Estudo térmico de um sistema solar de aquecimento de água residencial para duas configurações de superfície absorvedora

It presents a solar collector to be used in a system for heating water for bathing, whose main characteristics are its low cost and easy manufacturing and assembly. The absorbing surface of the collector is formed by an aluminum plate with eight flaps where they lodge PVC pipes. The catchment area of solar radiation corresponds to 1.3 meters. The collector box was made of wood, is covered by transparent glass and thermal insulation of tire chips and expanded polystyrene (EPS). Absorber tubes were connected in parallel through the use of PVC fittings and fixed to the plate by the use of metal poles and rivets. The entire absorber received paint flat black for better absorption of sunlight. The system worked on a thermosiphon assembly and absorber of the collector has been tested in two configurations: with the tubes facing up, directly exposed to the impact of sunlight and facing down, exchanging heat with the plate by conduction. It was determined the most efficient configuration for the correct purpose. The solar collector was connected to a thermal reservoir, also alternative, low-cost forming the system of solar water heating. We evaluated thermal parameters that proved the viability of the heating system studied

Análise da sensibilidade do biodiesel B5 em frotas de transporte coletivo com motorização diesel

The aim of this study was investigate the consolidation of the biodiesel fuel used in (a) engines of urban and intercity bus companies, (b) a stationary engine. It was necessary to investigate and analyze, technologically, if the biodiesel fuels were presenting troubleshooting relative to wear of parts lied to fuel and to evaluate the consumption fluctuations of this fuel. The urban and intercity bus companies, localized in Natal, Rio Grande do Norte state, Brazil, had 41 and 12 vehicles, respectively. It were analyzed datasheet of each one vehicle during three years, since 2008 until 2010 and were interviewed the management of the maintenance team of bus companies relative to aspects concerning the substitution of the diesel fuel by the B5 biodiesel. The second aim of this study was visually inspect the wear of the parts directly lied to combustion process. For this reason, it was investigated a stationary engine, manufactured by Branco BD5, 5 HP of power, fueled by (a) diesel, (b) biodiesel B5, (c) biodiesel B20 and (d) diesel or biodiesel, both contaminated by distilled water. In this engine, its power utilizing biodiesel B5 versus diesel was lower about 5.2% and, in the investigated case of B20 versus diesel, it was lower around 11.5%

Desempenho de um veículo flex em bancada dinamométrica de chassi

Flex-fuel vehicles are equipped with Otto Cycle internal combustion engines and have the capability of functioning with more than one type of fuel, mixed at the same tank and burned in the combustion chamber simultaneously. This sort of motorization is a world pattern due to the scarcity of petroleum, the trade of several types of fuels, technology advances and the restriction imposed to gas emissions to the atmosphere. In Brazil, the Flexfuel vehicles are a reality, specially the ones using fuel with 20 to 25% anhydrous alcohol mixed with gasoline and those that use natural gas or original liquid fuel (gasoline or hydrated ethanol). The Brazilian model Fiat Siena, the object of this present scientific investigation, is equipped with a unique electronic central capable of managing the liquid or gaseous fuels. The purpose of this research was to perform a comparative analysis in terms of performance (in terms of both potency and consumption) of a tetra-fuel vehicle - using a chassis dynamometer, operating with different fuels: common gasoline, premium gasoline, Podium gasoline, ethanol or natural gas. It became necessary to develop a bench of tests and trials procedures, as well as to know the functioning of the electronic management of the vehicle under analysis. The experiments were performed at the automotive laboratory in CTGAS-ER (Center of Gas Technologies and Renewable energies) at the light of Brazilian standard ABNT, NBR 7024: Light on-road vehicles - measurement of fuel consumption. The essay results on specific fuel consumption using common gasoline, premium gasoline and Podium gasoline have shown similar results, both for urban and road driving cycles

Otimização topológica de estruturas termoelásticas tridimensionais

This work presents an optimization technique based on structural topology optimization methods, TOM, designed to solve problems of thermoelasticity 3D. The presented approach is based on the adjoint method of sensitivity analysis unified design and is intended to loosely coupled thermomechanical problems. The technique makes use of analytical expressions of sensitivities, enabling a reduction in the computational cost through the use of a coupled field adjoint equation, defined in terms the of temperature and displacement fields. The TOM used is based on the material aproach. Thus, to make the domain is composed of a continuous distribution of material, enabling the use of classical models in nonlinear programming optimization problem, the microstructure is considered as a porous medium and its constitutive equation is a function only of the homogenized relative density of the material. In this approach, the actual properties of materials with intermediate densities are penalized based on an artificial microstructure model based on the SIMP (Solid Isotropic Material with Penalty). To circumvent problems chessboard and reduce dependence on layout in relation to the final optimal initial mesh, caused by problems of numerical instability, restrictions on components of the gradient of relative densities were applied. The optimization problem is solved by applying the augmented Lagrangian method, the solution being obtained by applying the finite element method of Galerkin, the process of approximation using the finite element Tetra4. This element has the ability to interpolate both the relative density and the displacement components and temperature. As for the definition of the problem, the heat load is assumed in steady state, i.e., the effects of conduction and convection of heat does not vary with time. The mechanical load is assumed static and distributed

Controle de plantas daninhas em arroz irrigado mediante o momento da admissão e da altura da lâmina de água

Este trabalho, desenvolvido ao nível de campo, na Fazenda Experimental Edgárdia, da Faculdade de Ciências Agronômicas da UNESP, Botucatu, no ano agrícola 1990/91, objetivou avaliar os efeitos do momento de admissão da água e da altura da lâmina de água sobre o desenvolvimento das plantas daninhas e os reflexos sobre as de arroz. O delineamento experimental usado foi de blocos ao acaso com parcelas subsubdivididas. Às parcelas, corresponderam os momentos de admissão de água M1, M2 e M3, respectivamente, 15, 42 e 74 dias após a emergência das plantas de arroz. As subparcelas corresponderam às alturas das lâminas de água L5, L10 e L15, respectivamente, 5, 10 e 15 cm e as subsubparcelas, a dois sistemas de condução: com capina (cc) e sem capina (sc). Verificou-se que o desenvolvimento das plantas daninhas foi afetado tanto pelo momento de admissão de água como pela altura da lâmina de água sendo a produção de grãos reduzida 61,5% devido à competição das plantas daninhas com a cultura.

Seletividade de herbicidas em variedades de cana-de-açúcar

Este trabalho teve como objetivo avaliar a seletividade do herbicida topramezone aplicado de forma isolada e em mistura com tebuthiuron, em pós-emergência inicial, sobre dez variedades de cana-de-açúcar em condição de cana-planta. Os tratamentos utilizados foram: topramezone + Dash® (70 g ha-1 + 0,25% v/v); topramezone + tebuthiuron + Dash® (70 + 1.000 g ha-1 + 0,25% v/v); topramezone + tebuthiuron + Dash® (100 + 1.000 g ha-1 + 0,25% v/v); e ametryn + tebuthiuron (1.500 + 1.000 g ha-1), aplicados aos 35 dias após o plantio, além de uma testemunha sem aplicação de herbicidas. Durante a condução do experimento, todas as parcelas permaneceram livres da interferência das plantas daninhas por meio de capinas. As plantas de cana-de-açúcar estavam com duas a quatro folhas por ocasião da aplicação dos herbicidas. O delineamento experimental utilizado foi o de blocos casualizados em parcelas subdivididas, com quatro repetições, sendo as variedades dispostas nas parcelas e os herbicidas nas subparcelas. As variedades utilizadas foram: SP 83 2847, SP 80 3280, RB 85 5453, SP 80 1842, SP 89 1115, RB 86 7515, PO 8862, RB 85 5156, SP 80 1816 e SP 81 3250. As avaliações visuais de fitotoxicidade foram realizadas aos 7, 14, 28 e 35 dias após a aplicação. Ao final do estudo foram determinados os parâmetros tecnológicos pol, fibra e brix e os parâmetros produtivos rendimento de colmos e produção de açúcar. A formulação isolada de topramezone seguida de suas misturas com tebuthiuron proporcionaram inicialmente severos sintomas visuais de injúrias às plantas de cana-de-açúcar; contudo, as plantas de todas as variedades testadas tiveram uma total recuperação visual a partir dos 35 dias após a aplicação dos herbicidas. A mistura de tebuthiuron com topramezone reduziu os sintomas de injúrias iniciais provocados por este último. A mistura de ametryn + tebuthiuron foi o tratamento que evidenciou a ação fitotóxica menos severa às plantas, independentemente da variedade estudada. Nenhum dos herbicidas testados afetou negativamente os componentes tecnológicos e produtivos, sendo as diferenças observadas dependentes apenas das variedades. Podem-se considerar seletivos os herbicidas utilizados sobre as variedades avaliadas de cana-de-açúcar.

Desenvolvimento de equipamento para controle mecânico de plantas aquáticas na UHE de Americana-SP

Os objetivos deste trabalho foram desenvolver e avaliar o rendimento operacional de um equipamento para controle de plantas aquáticas, além de estabelecer procedimentos que permitissem a otimização dessa prática na UHE de Americana-SP. O equipamento constitui-se de uma esteira de margem (3,0 m de largura x 10,0 m de comprimento) para captação e condução das plantas até um picador, que as fragmenta antes do descarte, facilitando assim sua decomposição e seu transporte. A análise realizada indicou que a capacidade operacional foi de aproximadamente 7,73 m³ h-1. Considerando-se a menor taxa de crescimento observada no histórico do reservatório, 2,27%, o sistema deveria permitir a remoção de aproximadamente 28 m³ h-1. Dessa forma, esse equipamento pode funcionar como um método auxiliar no controle das plantas aquáticas, não realizando um controle efetivo se empregado de forma isolada.

Teste de condutividade elétrica em função do período e da temperatura de embebição para sementes de milheto

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Duração do teste de germinação do capim-tanzânia

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Efeito do lodo de esgoto e nitrogênio na nutrição e desenvolvimento inicial da mamoneira

Aiming to evaluate the application effect of different sewage sludge ( SS) doses, with and without nitrogen addition, in the castorbean initial development, one experiment was installed in an entirely randomized experimental design, in split-plot scheme 5 X 2, constituted of five sewage sludge doses (0, 4, 8, 16 e 32 Mg ha(-1)) and nitrogen addition or not (15 kg ha(-1)), with five replications. The experimental unit was constituted of plastic bags with capacity of 3,5 dm(3) of soil. Fifty days after emergency it was evaluated height of plants, dry matter of the aerial part, nutrient content in the aerial part, soil electrical conductivity and soil chemical analysis. The SS doses promoted increase in the height of plants and dry matter of castorbean. The concentration of N, K, Mg and S and also the micronutrients Cu, Fe, Mn and Zn in the aerial part of the plants also suffered a positive effect with SS doses, the same didn't occur for the P and Ca concentrations. N addition increased the concentration of N, S, Cu and Zn in the plants. The SS did not present significant effect over pH levels, phosphorous, potassium, calcium, magnesium, organic matter and soil cation exchange capacity after the experiment conduction period.

Estado nutricional e componentes da produção de plantas de pimentão conduzidas em sistema de fertirrigação durante indução de estresse salino em cultivo protegido

O uso das técnicas de fertirrigação em ambiente protegido vem aumentando no Brasil devido à praticidade de condução e redução dos custos de produção. Apesar dessas vantagens, salienta-se que esta prática também pode trazer riscos, principalmente pelo acúmulo de sais na superfície do solo e na região periférica do bulbo radicular. em caso de salinização do solo pelo manejo incorreto do sistema podem ocorrer alterações na disponibilidade de nutrientes, com conseqüências fisiológicas no desenvolvimento das plantas. Neste trabalho, utilizou-se o pimentão (Capsicum annuum L.) como planta-modelo para estudos da interferência da salinidade na nutrição das plantas, pela alteração da condutividade elétrica (CE) na solução do solo. Os resultados revelaram indícios de antagonismo entre nutrientes, notadamente entre as formas catiônicas em razão do aumento da concentração de KCl nos tratamentos com alta CE. A suplementação do solo com adubo orgânico não atenuou os efeitos do aumento da concentração salina e os valores extremos de CE interferiram drasticamente na produção.

Estudo dos óxidos A2B2O7 e ABO3 a base de terras raras, para aplicações térmicas e catalíticas a altas temperaturas

Rare earth elements have recently been involved in a range of advanced technologies like microelectronics, membranes for catalytic conversion and applications in gas sensors. In the family of rare earth elements like cerium can play a key role in such industrial applications. However, the high cost of these materials and the control and efficiencies associated processes required for its use in advanced technologies, are a permanent obstacle to its industrial development. In present study was proposed the creation of phases based on rare earth elements that can be used because of its thermal behavior, ionic conduction and catalytic properties. This way were studied two types of structure (ABO3 and A2B2O7), the basis of rare earths, observing their transport properties of ionic and electronic, as well as their catalytic applications in the treatment of methane. For the process of obtaining the first structure, a new synthesis method based on the use of EDTA citrate mixture was used to develop a precursor, which undergone heat treatment at 950 ° C resulted in the development of submicron phase BaCeO3 powders. The catalytic activity of perovskite begins at 450 ° C to achieve complete conversion at 675 ° C, where at this temperature, the catalytic efficiency of the phase is maximum. The evolution of conductivity with temperature for the perovskite phase revealed a series of electrical changes strongly correlated with structural transitions known in the literature. Finally, we can establish a real correlation between the high catalytic activity observed around the temperature of 650 ° C and increasing the oxygen ionic conductivity. For the second structure, showed clearly that it is possible, through chemical processes optimized to separate the rare earth elements and synthesize a pyrochlore phase TR2Ce2O7 particular formula. This "extracted phase" can be obtained directly at low cost, based on complex systems made of natural minerals and tailings, such as monazite. Moreover, this method is applied to matters of "no cost", which is the case of waste, making a preparation method of phases useful for high technology applications

O efeito do regime hidrológico do semiárido na composição de espécies durante dominância de cianobactérias em um reservatório tropical

The potentially toxic cyanobacterial blooms in water bodies are spread across the globe, resulting in the loss of water quality and adverse effects on human health. In arid and semiarid regions, the hydrologic regime characterized by an annual cycle of drought and rain, change the volume and the retention time of the reservoir. Such changes affect the limnological characteristics and causing changes in composition and biomass community of cyanobacteria. The reservoir Cruzeta (Zmax = 8.7 m) is a eutrophic water supply source located in the semiarid tropical (Northeast Brazil). Raised the hypothesis that the hydrological regime of semi-arid tropical is a determining factor in the availability of resources in eutrophic water sources, which influences the composition of dominant species of cyanobacteria. The aim of this study was to analyze the changes in biomass and species composition of cyanobacteria for two annual hydrological cycles and evaluate factors drivers. The study was divided into five distinct periods (dry 2010, rain 2011, dry 2011, rain 2012, dry 2012). The dominant group found in all periods was Cyanobacteria (99% of total biomass), which contributed to the low diversity. The filamentous species Cylindrospermopsis raciborskii was present at both points in almost every study. The colonial species Microcystis panniformis and Sphaerocavum brasiliensis dominated only in periods with lower volumes of water. The diatoms contribute more to the biomass during the period of severe drought. The point near the dam (P1) had phytoplankton biomass larger than the point near the tributary (P2). The dominant species of colonial cyanobacteria lasted until the overflow in P1, and P2 this dominance was until the first rains. The redundancy analysis indicated that physical factors such as light availability and water level were the main factors driving the seasonal succession of phytoplankton. The composition of phytoplankton in spring was alternated by species of filamentous cyanobacteria in conditions of poor stability of the water column, such as Cylindrospermopsis raciborskii, and colonial species under conditions of high stability of the water column, such as Microcystis panniformis and Sphaerocavum brasiliensis. The extremes of torrential rains and severe droughts, governed by the hydrological regime of the semi-arid region led to the availability of resources in the watershed, directing the spatial and temporal dynamics of phytoplankton in the reservoir Cruzeta

Avaliando a aprendizagem de língua inglesa em uma escola de ensino médio a partir de contribuições discentes

This study discusses the evaluation of the English language‟s learning developed in a public high school from Lajes-RN in 2011 starting from a qualitative evaluation proposal (SAUL 1988; CANAN, 1996; DEMO, 2008) aiming the production of knowledge about the evaluation process developed in the classes of English language involving the contributions from students. To diagnose and characterize the evaluation process of English language of the researched school, identifying the representations that students attributed to the evaluation, we have implemented the evaluation instruments suggested by students to perform the evaluation of language learning and allowed a reflection about the student‟s participation in the construction of the evaluation process of the English language, subject discussed by Sant‟anna (2002) and other theorists (CANAN, 1996; BRAZIL, 2002; PEREIRA, 2009). To conduct the research work, we use the qualitative approach with ethnographic basis, substantiate in authors like Bogdan, Biklen (1994), Mazzotti; Gewandsznajder (1998), Strauss, Corbin (2008) among others. The methodology was the action research (ANDRÉ, 1995; NUNAN, 2007; LANKSHEAR; KNOBEL, 2008) described as research of empirical basis which associates an action with a resolution of a collective problem, because in it, its researchers and employees are engaged in a cooperatively way (THIOLLENT, 1985). When we treat about the evaluation of English language‟s learning (ALMEIDA FILHO, 1993; SCARAMUCCI, 2009) practiced before and after the contributions made by the students of the second year of the refereed school, the study considers that high school students have a more critical and reflective conscience with regard to their evaluations, not just opining on the assessment of learning English but also about the assessment of other subjects from their scholar curriculum and so this research presents possibilities for performing the act of evaluation which consider the participation of students in decisions regarding this process, because we cogitate that when the teachers share the decisions with their students, teachers can add quality to the evaluation process

Comportamento elétrico a alta temperatura de termistor cerâmico alfa-Fe2O3 com coeficiente de temperatura negativo

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)