Effect of polymerization techniques and cleaning solution on flexural resistance of acrylic resin chemically activated

The purpose of this study was to evaluate the impact of different disinfection solutions on flexural resistance of chemically-activated acrylic resin. Test pieces were made of clear acrylic resin using a rectangular mold and employing two techniques: wet polymerization under pressure (n = 20) and dry polymerization under pressure (n = 20). Test pieces were subdivided into four equal groups: distilled water (control), sodium bicarbonate, 1% sodium hypochlorite and effervescent ats. The 30-day cycling technique consisted of immersing the test pieces in 100 ml of solution for 10 min three times a day and placing them in closed containers containing artificial saliva at 37°C. Subsequently, the flexural resistance of samples was tested. Data were analyzed using two-way analysis of variance (ANOVA) with forces serving as the dependent variables and the polymerization technique and cleaning agents as independent variables. Post hoc multiple comparisons were performed using Tukey’s test. There was no statistically significant difference in the flexural strength between the two polymerization techniques. The greatest flexural strength was observed for the effervescent tablets group followed by the control and 1% sodium hypochlorite groups which were statistically similar. Thus, the sodium bicarbonate solution caused the lowest flexural resistance of the test pieces.

Efeito de diferentes gomas de mascar sobre o pH salivar de crianças

Objective: To evaluate the effect of different chewing gum brands on the salivary pH of children with primary dentition. Method: Forty children were selected and assigned to four groups: control (no chewing gum); sugarless chewing gum; chewing gum with casein phosphopeptide-amorphous calcium phosphate; and chewing gum with xylitol. The first saliva collection was made after supervised tooth brushing for stabilization of the oral pH. Next, all children were instructed to drink slowly 100 mL of a cola-based soft drink (Coca-Cola®) and a new saliva collection was made 10 min later. Then, each group chewed on the chewing gum for 5 min and discarded it after this time. Saliva was collected again at 5, 10 and 15 min intervals after start using the chewing gum. Measurement of salivary pH was made with colorimetric test papers and a digital pH-meter. Data were analyzed statistically by analysis of variance and Tukey’s test at a 5% significance level. Results: The use of chewing gums accelerated the increase of salivary pH to considerably alkaline levels after consumption of an acidic beverage, especially within the first minutes. The highest levels were obtained in the groups of children that used chewing gums containing xylitol and casein phosphopeptide-amorphous calcium phosphate. Conclusion: Children that used the chewing gums after ingestion of an acidic soft drink presented an increase in salivary pH, with the best results in the groups that used chewing gums containing casein phosphopeptide-amorphous calcium phosphate and xylitol.

Effect of peroxide bleaching on the biaxial flexural strength and modulus of bovine dentin

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Study of the feasibility of mix of species from sawmill waste and limiting for particleboard

This study aims to determine physical properties of particleboard made of sawmill waste, as a mix of several wood species, and two adhesives: urea-formaldehyde, usually employed in industry (even with drawbacks or formaldehyde emission during pressing) and FASTBOND®, water based resin, still poorly referenced in literature. Sixteen panels have been produced, in four experimental conditions, defined by using two adhesives and a 12 mm thick limiter (or not). Variance analysis was adopted to evaluate influence of experimental conditions on physical properties of produced panels, manufactured in nominal dimensions 350x350mm; 10% resin related to particles mass (at 5% moisture); 3.5 MPa compaction pressure, temperature 130°C, in a 10 min cycle. Tests to determine density, moisture content, swelling and water absorption were carried out based on normative parameters of ABNT NBR 14810:2006. Results have been satisfactory to panels produced with urea-formaldehyde but those manufactured with polychloroprene based resin (FASTBOND®) not meet regulatory requirements. Best results have been obtained without limiter.

Influência de tratamentos a plasma na resistência à corrosão e na propriedade de adesão de uma camada protetiva sobre a superfície de ligas de alumínio

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Estrutura supramolecular de um derivado de perileno em filmes finos fabricados por evaporação térmica a vácuo

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Qualidade pós-colheita dos frutos de jabuticaba tratada por hidrotermia

This study aimed to evaluate the hydrothermal effect on conservation of two jabuticaba fruits, Myrciaria jabuticaba Vell. Berg. Fruits were subjected to thermal treatment by 10 min at 5, 10, 15, 20 and 25 ºC and wrapped into expanded polystyrene trays, stored at 9 ºC and 85-90% RH, being evaluated every 5 d. Shelf life, weight loss, respiratory rate, soluble solids, titrable acidity, texture, C vitamin, pH, total and soluble pectin and polypheno loxidase activity were evaluated. Lower shelf life was observed for control treatment (31 d) and largest was found at 15, 20 and 25 ºC (45 d). A sligthly delay was observed in the breathing pick at 15, 20 and 25 ºC at 25 d and not in the 20 d as observed in the other treatments. Soluble solids increased with storage time for all of temperature treatment, but at 15, 20 and 25 ºC increase was smaller. Texture an C vitamin were higher in fruits stored at 25 ºC. Soluble pectin was smaller at the end of storage period, at temperatures of 20 and 25 ºC. Polyphenoloxidase activity decreased along 30 d regardless storage temperature. Treatments at 20 and 25 ºC were the most effective for mainteining posthaverst quality of the jabuticaba fruits.

Avaliação do conteúdo gástrico pela ultrassonografia

Pós-graduação em Anestesiologia - FMB

EC33-136 Corn in Nebraska

Corn is Nebraska's most important crop. Of the nearly 19 million acres under cultivation in the state, over 10 million acres or more than 50 percent is normally planted to corn. This is three times the acreage of wheat, four times that of oats, and ten times that of barley. The 10-year average acre yield of corn for this state is 25.8 bushels compared with 26.9 bushels for the entire United States. Nebraska, with an average annual crop of approximately 258 million bushels, usually ranks third among all states in the total production of corn, being exceeded by Iowa and Illinois. This 1933 extension circular discusses the importance of corn, seed, varieties of corn, freezing injury, testing seed corn, hybrid corn, soil fertility and rotation, cultural practices, harvesting and storing corn, power machinery in relation to costs in corn production, corn diseases and insects, and utilization of corn.

Thermostable invertases from Paecylomyces variotii produced under submerged and solid-state fermentation using agroindustrial residues

The filamentous fungus Paecylomices variotii was able to produce high levels of cell extract and extracellular invertases when grown under submerged fermentation (SbmF) and solid-state fermentation, using agroindustrial products or residues as substrates, mainly soy bran and wheat bran, at 40A degrees C for 72 h and 96 h, respectively. Addition of glucose or fructose (a parts per thousand yen1%; w/v) in SbmF inhibited enzyme production, while the addition of 1% (w/v) peptone as organic nitrogen source enhanced the production by 3.7-fold. However, 1% (w/v) (NH4)(2)HPO4 inhibited enzyme production around 80%. The extracellular form was purified until electrophoretic homogeneity (10.5-fold with 33% recovery) by DEAE-Fractogel and Sephacryl S-200 chromatography. The enzyme is a monomer with molecular mass of 102 kDa estimated by SDS-PAGE with carbohydrate content of 53.6%. Optima of temperature and pH for both, extracellular and cell extract invertases, were 60A degrees C and 4.0-4.5, respectively. Both invertases were stable for 1 h at 60A degrees C with half-lives of 10 min at 70A degrees C. Mg2+, Ba2+ and Mn2+ activated both extracellular and cell extract invertases from P. variotii. The kinetic parameters K-m and V-max for the purified extracellular enzyme corresponded to 2.5 mM and 481 U/mg prot(-1), respectively.

Epidural anesthesia and postoperatory analgesia with alpha-2 adrenergic agonists and lidocaine for ovariohysterectomy in bitches

The aim of this study was to determine the viability and cardiorespiratory effects of the association of epidural alpha-2 adrenergic agonists and lidocaine for ovariohysterectomy (OH) in bitches. Forty-two bitches were spayed under epidural anesthesia with 2.5 mg/kg body weight (BW) of 1% lidocaine with adrenaline (CON) or in association with 0.25 mg/kg BW of xylazine (XYL), 10 mu g/kg BW of romifidine (ROM), 30 mu g/kg BW of detomidine (DET), 2 mu g/kg BW of dexmedetomidine (DEX), or 5 mu g/kg BW of clonidine (CLO). Heart rate (HR), respiratory rate (f(R)) and arterial pressures were monitored immediately before and every 10 min after the epidural procedure. Blood gas and pH analysis were done before, and at 30 and 60 min after the epidural procedure. Animals were submitted to isoflurane anesthesia if they presented a slightest sign of discomfort during the procedure. Time of sensory epidural block and postoperative analgesia were evaluated. All animals in CON and DEX, 5 animals in ROM and CLO, 4 animals in XYL, and 3 in DET required supplementary isoflurane. All groups, except CLO, showed a decrease in HR. There was an increase in arterial pressures in all groups. Postoperative analgesia lasted the longest in XYL. None of the protocols were totally efficient to perform the complete procedure of OH; however, xylazine provided longer postoperative analgesia than the others.

Effects of different cryopreservation methods on post-thaw culture conditions of in vitro produced bovine embryos

The aim of this work was to evaluate the effect of cryopreservation protocols on subsequent development of in vitro produced bovine embryos under different culture conditions. Expanded in vitro produced blastocysts (n = 600) harvested on days 7-9 were submitted to controlled freezing [slow freezing group: 10% ethylene glycol (EG) for 10 min and 1.2 degrees C/min cryopreservation]; quick-freezing [rapid freezing group: 10% EG for 10 min, 20% EG + 20% glycerol (Gly) for 30 s]; or vitrification [vitrification group: 10% EG for 10 min, 25% EG + 25% Gly for 30 s] protocols. Control group embryos were not exposed to cryoprotectant or cryopreservation protocols and the hatching rate was evaluated on day 12 post-insemination. In order to evaluate development, frozen-thawed embryos were subjected to granulosa cell co-culture in TCM199 or SOFaa for 4 days. Data were analyzed by PROC MIXED model using SAS Systems for Windows (R). Values were significant at p < 0.05. The hatching rate of the control group was 46.09%. In embryos cultured in TCM199, slow freezing and vitrification group hatching rates were 44.65 +/- 5.94% and 9.43 +/- 6.77%, respectively. In embryos cultured in SOFaa, slow freezing and vitrification groups showed hatching rates of 11.65 +/- 3.37 and 8.67 +/- 4.47%, respectively. In contrast, the rapid freezing group embryos did not hatch, regardless of culture medium. The slow freezing group showed higher hatching rates than other cryopreservation groups. Under such conditions, controlled freezing (1.2 degrees C/min) can be an alternative to cryopreservation of in vitro produced bovine embryos.

A comparative study between crack analysis and a mechanical test for assessing the polymerization stress of restorative composites

Objectives. To verify the hypothesis that crack analysis and a mechanical test would rank a series of composites in a similar order with respect to polymerization stress. Also, both tests would show similar relationships between stress and composite elastic modulus and/or shrinkage. Methods. Soda-lime glass discs (2-mm thick) with a central perforation (3.5-mm diameter) received four Vickers indentations 500 mu m from the cavity margin. The indent cracks were measured (500x) prior and 10 min after the cavity was restored with one of six materials (Kalore/KL, Gradia/GR, Ice/IC, Wave/WV, Majesty Flow/MF, and Majesty Posterior/MP). Stresses at the indent site were calculated based on glass fracture toughness and increase in crack length. Stress at the bonded interface was calculated using the equation for an internally pressurized cylinder. The mechanical test used a universal testing machine and glass rods (5-mm diameter) as substrate. An extensometer monitored specimen height (2 mm). Nominal stress was calculated dividing the maximum shrinkage force by the specimen cross-sectional area. Composite elastic modulus was determined by nanoindentation and post-gel shrinkage was measured using strain gages. Data were subjected to one-way ANOVA/Tukey or Kruskal-Wallis/Mann-Whitney tests (alpha: 5%). Results. Both tests grouped the composites in three statistical subsets, with small differences in overlapping between the intermediate subset (MF, WV) and the highest (MP, IC) or the lowest stress materials (KL, GR). Higher stresses were developed by composites with high modulus and/or high shrinkage. Significance. Crack analysis demonstrated to be as effective as the mechanical test to rank composites regarding polymerization stress. (c) 2012 Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

A comparative evaluation of polymerization stress data obtained with four different mechanical testing systems

Objectives. The null hypothesis was that mechanical testing systems used to determine polymerization stress (sigma(pol)) would rank a series of composites similarly. Methods. Two series of composites were tested in the following systems: universal testing machine (UTM) using glass rods as bonding substrate, UTM/acrylic rods, "low compliance device", and single cantilever device ("Bioman"). One series had five experimental composites containing BisGMA:TEGDMA in equimolar concentrations and 60, 65, 70, 75 or 80 wt% of filler. The other series had five commercial composites: Filtek Z250 (3M ESPE), Filtek A110 (3M ESPE), Tetric Ceram (Ivoclar), Heliomolar (Ivoclar) and Point 4 (Kerr). Specimen geometry, dimensions and curing conditions were similar in all systems. sigma(pol) was monitored for 10 min. Volumetric shrinkage (VS) was measured in a mercury dilatometer and elastic modulus (E) was determined by three-point bending. Shrinkage rate was used as a measure of reaction kinetics. ANOVA/Tukey test was performed for each variable, separately for each series. Results. For the experimental composites, sigma(pol) decreased with filler content in all systems, following the variation in VS. For commercial materials, sigma(pol) did not vary in the UTM/acrylic system and showed very few similarities in rankings in the others tests system. Also, no clear relationships were observed between sigma(pol) and VS or E. Significance. The testing systems showed a good agreement for the experimental composites, but very few similarities for the commercial composites. Therefore, comparison of polymerization stress results from different devices must be done carefully. (c) 2012 Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

Oxytocin interference in the effects induced by inhalation of 7.5% CO2 in healthy volunteers

Objective The objective of this study was to assess the acute effect of intranasally administered oxytocin (OT) on subjective states, cardiovascular, and endocrine parameters in healthy volunteers who inhaled 7.5% CO2. Methods Forty-five subjects were allocated into three matched groups of subjects who received 24?international units (IU) of OT, 2?mg of lorazepam (LZP), or placebo (PL). The challenge consisted of medical air inhalation for 20?min, 10?min of rest, and CO2 7.5% inhalation for 20?min. Subjective effects were evaluated by self-assessment scales; heart rate, blood pressure, skin conductance, and salivary cortisol were also measured. Assessments were performed at four time points: (i) baseline (-15?min); (ii) post-air inhalation (90?min); (iii) post-CO2 inhalation (120?min), and (iv) post-test (160?min). Results CO2 inhalation significantly increased the anxiety score in the PL group compared with the post-air measurement but not in the OT or LZP groups. The LZP reduced anxiety after medical air inhalation. Other parameters evaluated were not affected by OT. Conclusion OT, as well as LZP, prevented CO2-induced anxiety, suggesting that this hormone has anxiolytic properties. Copyright (C) 2012 John Wiley & Sons, Ltd.