Particle number and mass emission factors from combustion of wood samples collected from Queensland forest

Knowledge of particle emission characteristics associated with forest fires and in general, biomass burning, is becoming increasingly important due to the impact of these emissions on human health. Of particular importance is developing a better understanding of the size distribution of particles generated from forest combustion under different environmental conditions, as well as provision of emission factors for different particle size ranges. This study was aimed at quantifying particle emission factors from four types of wood found in South East Queensland forests: Spotted Gum (Corymbia citriodora), Red Gum (Eucalypt tereticornis), Blood Gum (Eucalypt intermedia), and Iron bark (Eucalypt decorticans); under controlled laboratory conditions. The experimental set up included a modified commercial stove connected to a dilution system designed for the conditions of the study. Measurements of particle number size distribution and concentration resulting from the burning of woods with a relatively homogenous moisture content (in the range of 15 to 26 %) and for different rates of burning were performed using a TSI Scanning Mobility Particle Sizer (SMPS) in the size range from 10 to 600 nm and a TSI Dust Trak for PM2.5. The results of the study in terms of the relationship between particle number size distribution and different condition of burning for different species show that particle number emission factors and PM2.5 mass emission factors depend on the type of wood and the burning rate; fast burning or slow burning. The average particle number emission factors for fast burning conditions are in the range of 3.3 x 1015 to 5.7 x 1015 particles/kg, and for PM2.5 are in the range of 139 to 217 mg/kg.

The guide to the project management body of knowledge (PMBOK Guide) : applicability and contribution to project success in Australia

The PMBOK Guide is one of the most influential publications concerning the knowledge of the project manangement. Moreover, the pervasion of this guide seems to be set to increase as the basis of accreditation - in conjunction with the increasing global trend toward obtaining project management professional status. However, despite the influence and strengthening profile of this guide, reports continue to be published that detail numerous project failures in a wide range of different industries. The PMBOK Guide comprises mainly declarative (know-what) and procedural (know-how) information. In this sense, the guide is largely normative and provides a very good example of the limitations of this approach as highlighted by proponents of a move to the genuine application of positibe theory in project management.----- The aim of this paper is to determine the applicability of the guide in Australia and to determine the extent to which project success can be attributed to the guide. Project Managers from a variety of organisations were surveyed. This postal survey yielded 48 replies. Descriptive statistics was used to assess the incidence and effectivieness of all the processes in the guide. The results indicate that there were no processes that could be considered as peripheral or as a candidate for elimination from the guide. More specifically, all the processes were identified as either a key routine process or a key selective process and positively related to the level of project success. However, the results also indicated that other major factors pertaining to causal knowledge (know-why) are, at least, equally important determinants of project success. It is concluded that declarative, procedural and causal knowledge are all valuable, and given the preponderance of the first two types of knowledge, there seems to be an urgent need to now ensure an equal quest for causal knowledge. In terms of developing causal knowledge, a good starting point would appear to be both positive theory from production and economics.

Mobile communications : a study of factors influencing consumer use of m-services

New mobile digital communication technologies present opportunities for advertisers to capitalize on the evolving relationships of consumers with their mobile devices and their desire to access enhanced information services while mobile (m-services). Consumers already use mobile devices (cell phones, personal mobile digital assistants) for traditional phone calls and message handling (e.g., Kalakota and Robinson, 2002; Sullivan Mort and Drennan, 2002). The combination of rapidly developing mobile digital technology and high uptake rates of mobile devices presents enormous potential for delivery of m-services through these devices (Bitner, Brown, and Meuter, 2000). M-services encompass a wide variety of types including the ability to trade stock, to book theater and movie tickets while accessing seating plans online, to send and receive text and pictures, and receive personalized direct advertising such as alerts for shopping bargains. Marketing communications, and specifically advertising, may be delivered as an m-service and termed m-services advertising, forming part of the broader category of m-services. However, advertising research has not yet addressed the area of m-services and needs to do so to be able to take advantage of the advanced interactivity (Yadav and Varadarajan, 2005) of mobile communication devices. Such advertising research is likely to help develop open attitudes and responses to new business models as has been advocated for other new technology such as advanced television (Tauder, 2005). In this article, we model the factors influencing the use of m-services, in the context of consumers' existing relationships with mobile devices. First, we address the value propositions underpinning consumer involvement with mobile devices. Next, we canvass the types of involvement relevant to this consumption domain and argue that involvement, together with personal attributes innovativeness and self-efficacy, will influence use of m-services. Finally, implications for advertising delivered as an m-service are discussed, the potential for m-services advertising as part of m-commerce are canvassed, and directions for future research identified.

Issues in the development of pitch labelling skill

Pitch discrimination skills are important for general musicianship. The ability to name musical notes or produce orally any named note without the benefit of a known reference is called Absolute Pitch (AP) and is comparatively rare. Relative Pitch (RP) is the ability to name notes when a known reference is available. AP has historically been regarded as being innate. This paper will examine the notion that pitch discrimination skill is based on knowledge constructed through a suite of experiences. That is, it is learnt. In particular, it will be argued that early experiences promote the development of AP. Second it will argue that AP and RP represent different types of knowledge, and that this knowledge emerges from different experiences. AP is a unique research phenomenon because it spans the fields of cognition and perception, in that it links verbal labels with physiological sensations, and because of its rarity. It may provide a vantage for investigating the nature/nurture of musicianship; expertise; knowledge structure development; and the role of knowledge in perception. The study of AP may inform educational practice and curriculum design both in music and cross-curriculur. This paper will report an initial investigation into the similarities and differences between the musical experiences of AP possessors and the manifestation of their AP skill. Interview and questionnaire data will be used for the development and proposal of a preliminary model for AP development.

Experiential knowledge representation and the design of product usability

The topic of designers’ knowledge and how they conduct design process has been widely investigated in design research. Understanding theoretical and experiential knowledge in design has involved recognition of the importance of designers’ experience of experiencing, seeing, and absorbing ideas from the world as points of reference (or precedents) that are consulted whenever a design problem arises (Lawson, 2004). Hence, various types of design knowledge have been categorized (Lawson, 2004), and the nature of design knowledge continues to be studied (Cross, 2006); nevertheless, the study of the experiential aspects embedded in design knowledge is a topic not fully addressed. In particular there has been little emphasis on the investigation of the ways in which designers’ individual experience influences different types of design tasks. This research focuses on the investigation of the ways in which designers inform a usability design process. It aims to understand how designers design product usability, what informs their process, and the role their individual experience (and episodic knowledge) plays within the design process. This paper introduces initial outcomes from an empirical study involving observation of a design task that emphasized usability issues. It discusses the experiential knowledge observed in the visual representations (sketches) produced by designers as part of the design tasks. Through the use of visuals as means to represent experiential knowledge, this paper presents initial research outcomes to demonstrate how designers’ individual experience is integrated into design tasks and communicated within the design process. Initial outcomes demonstrate the influence of designers’ experience in the design of product usability. It is expected that outcomes will help identify the causal relationships between experience, context of use, and product usability, which will contribute to enhance our understanding about the design of user-product interactions.

From resource base to dynamic capabilities : an investigation of new firms

Despite the numerous observations that dynamic capabilities lie at the source of competitive advantage, we still have limited knowledge as to how access to firm-based resources and changes to these affect the development of dynamic capabilities. In this paper, we examine founder human capital, access to employee human capital, access to technological expertise, access to other specific expertise, and access to two types of tangible resources in a sample of new firms in Sweden. We empirically measure four dynamic capabilities and find that the nature and effect of resources employed in the development of these capabilities vary greatly. For the most part, there are positive effects stemming from access to particular resources. However, for some resources, such as access to employee human capital and access to financial capital, unexpected negative effects also appear. This study therefore provides statistical evidence as to the varying role of resources in capability development. Importantly, we also find that changes in resource bases have more influential roles in the development of dynamic capabilities than the resource stock variables that were measured at an earlier stage of firm development. This provides empirical support for the notion of treating the firm as a dynamic flow of resources as opposed to a static stock. This finding also highlights the importance of longitudinal designs in studies of dynamic capability development. Further recommendations for future empirical studies of dynamic capabilities are presented.

PSED II and the comprehensive Australian study of entrepreneurial emergence (CAUSEE)

Two current longitudinal studies in advanced countries, PSED II in the US and CAUSEE in Australia, have attempted to harmonize the major features of the research design. A comparison of the initial screening and first detailed interviews indicates a higher participation in new firm creation in the U.S. Similar types of persons are involved in both countries, albeit more immigrants, older individuals with more work experience and more established individuals in Australia. The nascent enterprises in the two countries are similar on many characteristics, although those in Australia report greater emphasis on new technology and international customers. Assessment of the prevalence of nascent enterprises and new firms from the Global Entrepreneurship Monitor surveys indicates a higher prevalence of new firms in Australia. These two longitudinal projects may help determine if this reflects a high proportion of new firm births or greater survival in the early years among Australian new firms.

Capital Works Procurement: The Selection of a Building Procurement Method

The determination of the most appropriate procurement method for capital works projects is a challenging task for the Department of Housing and Works (DHW) and other Western Australian State Government Agencies because of the array of assessment criteria that are considered and the procurement methods that are available. A number of different procurement systems can be used to deliver capital works projects such a traditional, design and construct and management. Sub-classifications of these systems have proliferated and continue to emerge in response to market demands. The selection of an inappropriate procurement method may lead to undesirable project outcomes. To facilitate DHW in selecting an appropriate procurement method for its capital works projects, a six step procurement method selection process is presented. The characteristics of the most common forms of procurement method used in Australia are presented. Case studies where procurement methods have been used for specific types of capital works in Western Australia are offered to provide a reference point and learning opportunity for procurement method selection.

Raman spectroscopic study of the metatellurate mineral : Xocomecatlite Cu3TeO4(OH)4

The mineral xocomecatlite is a hydroxy metatellurate mineral with Te6+O4 units. Tellurates may be subdivided according to their formula into three types of tellurate minerals: type (a) (AB)m(TeO4)pZq, type (b) (AB)m(TeO6).xH2O and (c) compound tellurates in which a second anion including the tellurite anion, is involved. The mineral Xocomecatlite is an example of the first type. Raman bands for xocomecatlite at 710, 763 and 796 cm-1 and 600 and 680 cm-1 are attributed to the ν1 (TeO4)2- symmetric and ν3 antisymmetric stretching mode. Raman bands observed at 2867 and 2926 cm-1 are assigned to TeOH stretching vibrations and enable estimation of the hydrogen bond distances of 2.622 Å (2867 cm-1), 2.634 Å (2926 cm-1) involving these OH units. The hydrogen bond distances are very short implying that they are necessary for the stability of the mineral.

User friendly guide for rehabilitation or strengthening of bridge structures using fiber reinforced polymer composites

A worldwide interest is being generated in the use of fibre reinforced polymer composites (FRP) in rehabilitation of reinforced concrete structures. As a replacement for the traditional steel plates or external post-tensioning in strengthening applications, various types of FRP plates, with their high strength to weight ratio and good resistance to corrosion, represent a class of ideal material in external retrofitting. Within the last ten years, many design guidelines have been published to provide guidance for the selection, design and installation of FRP systems for external strengthening of concrete structures. Use of these guidelines requires understanding of a number of issues pertaining to different properties and structural failure modes specific to these materials. A research initiative funded by the CRC for Construction Innovation was undertaken (primarily at RMIT) to develop a decision support tool and a user friendly guide for use of fibre reinforced polymer composites in rehabilitation of concrete structures. The user guidelines presented in this report were developed after industry consultation and a comprehensive review of the state of the art technology. The scope of the guide was mainly developed based on outcomes of two workshops with Queensland Department of Main Roads (QDMR). The document covers material properties, recommended construction requirements, design philosophy, flexural, shear and torsional strengthening of beams and strengthening of columns. In developing this document, the guidelines published on FIB Bulletin 14 (2002), Task group 9.3, International Federation of Structural Concrete (FIB) and American Concrete Institute Committee 440 report (2002) were consulted in conjunction with provisions of the Austroads Bridge design code (1992) and Australian Concrete Structures code AS3600 (2002). In conclusion, the user guide presents design examples covering typical strengthening scenarios.

The role of relational capabilities in developing the capacity for supply chain innovation

The purpose of this paper is to gain a better understanding of the types of relational capabilities supply chain participants develop to enable ongoing supply chain innovation capacity building that produces improved business outcomes. This is exploratory research using qualitative data gathered by using five interviews, with the Australian road freight industry as the context. Two key relational capabilities and the improvement of four key business outcomes were identified as being present in the interaction of freight transport service providers with members of their supply chain. The data also demonstrates that by entering into competence building relationships with customers and suppliers firms can build capabilities that will increase their capacity for supply chain innovation. Even in short term arm’s length relationships firms can acquire improved skills behaviours and practices that enhance their operation effectiveness and the efficiency of the supply chain relationships.

Down the aisle : the effects of technological change on retail workers skills

Reconfiguration of corporate structures and the retailer-supplier interface in the retail industry have restructured product markets and supply chains, as well as supermarket employment, over the past decade or so (Baret, Lehndorff & Sparks 2000; du Gay 1996). Various studies have examined the consequent changes in labour usage practices within supermarkets or superstores (Baret et al. 2000; Marchington 1995; Penn & Wirth 1993; Sparks 1992; Dawson, Findlay & Sparks 1987, 1986). Commonly, this literature explores the interplay between shifts in the structure of the labour market, broader societal trends and retailers’ employment strategies. One study found that domestic and gender dimensions, accompanied by industrial relations regimes, exert considerable influence on patterns of labour usage (Baret et al. 2000). However, while the types of labour usage and the drivers of changes to labour usage patterns have attracted significant academic attention, research has largely overlooked the ways in which the nature of supermarket work has evolved as a result of changing technology, which effectively bolsters managerial prerogative, and which has affected the skill levels of workers in the industry (Marchington 1995).

The aptitudes of allied health professionals working in remote communities

This study aimed to identify the aptitudes required in allied health professionals working in three different service delivery models serving remote locations in Northern tropical Australia. Eighteen allied health professionals including," dietetics, diabetes educators, occupational therapy, physiotherapy, psychology, podiatry, social work and speech pathology participated in this exploratory study using a narrative approach. A range of aptitudes were identified and themed under the following headings: (1) being organized but flexible, (2) cooperation and mediation, (3) culturally aware and accepting communicators, (4) knowing the community (5) resourcefulness and resilience and (6) reflectivity. Limiting factors were also deduced. Three of the themes are discussed in this paper. The study found that allied health professionals working in remote settings identified as important personal attributes not necessarily valued in metropolitan settings. Recruitment processes and education programs need to recognize the importance of personal attributes as well as professional skills.

Operation and control of a microgrid containing inertial and non-inertial micro sources

In this paper, a new power sharing control method for a microgrid with several distributed generation units is proposed. The presence of both inertial and noninertial sources with different power ratings, maximum power point tracking, and various types of loads pose a great challenge for the power sharing and system stability. The conventional droop control method is modified to achieve the desired power sharing ensuring system stability in a highly resistive network. A transformation matrix is formed to derive equivalent real and reactive power output of the converter and equivalent feedback gain matrix for the modified droop equation. The proposed control strategy, aimed for the prototype microgrid planned at Queensland University of Technology, is validated through extensive simulation results using PSCAD/EMTDC software.

Synthesis and Raman spectroscopic study of Mg/Al,Fe hydrotalcites with variable cationic ratios

Hydrotalcites of formula Mg6 (Fe,Al)2(OH)16(CO3).4H2O formed by intercalation with the carbonate anion as a function of divalent/trivalent cationic ratio have been successfully synthesised. The XRD patterns show variation in the d-spacing attributed to the size of the cation. Raman and infrared bands in the OH stretching region are assigned to (a) brucite layer OH stretching vibrations (b) water stretching bands and (c) water strongly hydrogen bonded to the carbonate anion. Multiple (CO3)2- symmetric stretching bands suggest that different types of (CO3)2- exist in the hydrotalcite interlayer. Increasing the cation ratio (Mg/Al,Fe) resulted in an increase in the combined intensity of the 2 Raman bands at around 3600 cm-1, attributed to Mg-OH stretching modes, and a shift of the overall band profile to higher wavenumbers. These observations are believed to be a result of the increase in magnesium in the structure. Raman spectroscopy shows a reduction in the symmetry of the carbonate, leading to the conclusion that the anions are bonded to the brucite-like hydroxyl surface and to the water in the interlayer. Water bending modes are identified in the infrared spectra at positions greater than 1630 cm-1, indicating the water is strongly hydrogen bonded to both the interlayer anions and the brucite-like surface.