Synthetic polymers blend used in the production of high activated carbon for pesticides removals from liquid phase

For the activated carbon (AC) production, we used the most common industrial and consumer solid waste, namely polyethyleneterephthalate (PET), alone or blended with other synthetic polymer such polyacrylonitrile (PAN). By mixing PET, with PAN, an improvement in the yield of the AC production was found and the basic character and some textural and chemical properties were enhanced. The PET–PAN mixture was subjected to carbonisation, with a pyrolysis yield of 31.9%, between that obtained with PET (16.9%) or PAN (42.6%) separately. The AC revealed a high surface area (1400, 1230 and 1117 m2 g−1) and pore volume (0.46, 0.56 and 0.50 cm3 g−1), respectively, for PET, PAN and PET–PAN precursors. Selected ACs were successfully tested for 4- chloro-2-methylphenoxyacetic acid (MCPA) and diuron removal from the liquid phase, showing a higher adsorption capacity (1.7 and 1.2 mmol g−1, respectively, for MCPA and diuron) and good fits with the Langmuir (PET) and Freundlich equation (PAN and PET–PAN blend). With MCPA, the controlling factor to the adsorption capacity was the porous volume and the average pore size. Concerning diuron, the adsorption was controlled essentially by the external diffusion. A remarkable result is the use of different synthetic polymers wastes, as precursors for the production of carbon materials, with high potential application on the pesticides removals from the liquid phase.

Using Different Co-Adjuvant Activating Agents to Improve Activated Carbon Adsorption Capacities

Activated carbon (AC) has proved to be an effective adsorbent for the removal of an assortment of organic and inorganic pollutants from aqueous or gaseous media. However, the pursuit for more effective and cheaper AC is still very active and a diversity of textural and chemical treatments are described as a way to expand their applications. It is well known that the surface area and surface chemistry of AC strongly affect their adsorption capacity [1-3]. In particular, an increase in the nitrogen content has been related to an increase of the basic character and also to the development of the porous structure. In most published work this was achieved through an AC post treatment, including either a reaction with nitrogen containing reagents, such as ammonia, nitric acid, or a diversity of amines. However, the AC prepared directly from a nitrogen rich precursor through a physical or chemical activation is referred to as presenting the best characteristics, namely high nitrogen content, high basic character, low nitrogen leaching and also a good thermal stability [4]. To improve the AC adsorption capacities for acidic pesticide removal from the aqueous phase, we intend to improve the porous structure and introduce nitrogenated groups directly into the AC matrix, using different co-adjuvant activating agents as a nitrogen source, by chemical activation, with potassium hydroxide, of cork or poly(ethyleneterephthalate) (PET) precursors.

Production of activated carbons from single and mixtures of synthetic polymers

The production of activated carbons (ACs) involves two main steps: the carbonization of the carbonaceous of raw materials at temperatures below 1073 K in the absence of oxygen and the activation had realized at the temperature up to 1173 but the most useful temperature at 1073 K. In our study we used the most common industrial and consumer solid waste, namely PET, alone or blended with other synthetic polymer PAN. By mixing the two polymers in different ratios, an improvement of the yield of the AC production was found and some textural properties were enhanced by comparison with the AC prepared using each polymer separately. When all the samples were exposed through the carbonization process with a pyrolysis the mixture of PAN-PET (1:1w/w) yield around 31.9%, between that obtained with PET (16.9%) or PAN (42.6%) separately. The combine activation, with CO2 at 1073 K, allow ACs with a lower burn-off degree isothermally, when compared with those attained with PET or PAN alone, but with similarly chemicals or textural properties. The resultant ACs are microporous in their nature, as the activation time increase, the PET-PAN mixture AC are characterized by a better developed porous structure, when associated with the AC prepared from PAN. The AC prepared from PET-PAN mixture are characterized by basic surface characteristics, with a pHpzc around 10.5, which is an important characteristic for future applications on acidic pollutants removals from liquid or gaseous phase. In this study we had used the FTIR methods to determine the main functional groups in the surface of the activated carbons. The adsorbents prepared from PAN fibres presents an IR spectrum with similar characteristics to those obtained with PET wastes, but with fewer peaks and bands with less intensity, in particular for the PAN-8240 sample. This can be reflected by the stretching and deformation modes of NH bond in the range 3100 – 3300 cm-1 and 1520 – 1650 cm-1, respectively. Also, stretching mode associated to C–N, C=N, can contributed to the profile of IR spectrum around 1170 cm-1, 1585 – 1770 cm-1. And the TGA methods was used to study the loses of the precursors mass according to the excessive of the temperature. The results showed that, there were different decreasing of the mass of each precursors. PAN degradation started at almost 573 K and at 1073 K, PAN preserve more than 40% of the initial mass. PET degradation started at 650 K, but at 1073 K, it has lost 80% of the initial mass. However, the mixture of PET-PAN (1:1w/w) showed a thermogravimetric profile between the two polymers tested individually, with a final mass slightly less than 30%. From a chemical point of view, the carbonisation of PET mainly occurs in one step between 650 and 775 K.

Preparação, caracterização e modificação de adsorventes para remoção de pesticidas de águas

O objectivo principal deste trabalho de mestrado consistiu em avaliar a potencial utilização de materiais adsorventes, nomeadamente, de carvões activados (AC) preparados por activação química com KOH, a partir de PET reciclado, e de materiais com estrutura mesoporosa ordenada, do tipo MCM-41 e SBA-15, na remoção de ácido 4 - cloro - 2 - metilfenoxiacético (MCPA) e de azul de metileno (MB), presentes nas águas. Nesta tese apresentam-se estudos de preparação e caracterização de materiais micro e mesoporosos e também estudos de avaliação da capacidade adsortiva em fase líquida. Prepararam-se três materiais microporosos, nomeadamente, PET-2-700, PET-2-700ox (AC oxidado) e PET-2-700red (AC reduzido), dois materiais constituídos exclusivamente por mesoporos, Si-MCM-41 e Ti-MCM-41-50 e dois materiais contendo maioritariamente mesoporos, mas que também possuem alguma microporosidade, tais corno, Si-SBA-15 e Ti-SBA-15-50. A caracterização textural dos adsorventes foi inferida por adsorção de azoto a 77K e por de difracção de raios X. Recorreu-se a três métodos de análise das isotérmicas, nomeadamente, Dubinin-Radushkevich, Brunauer-Ernrnett-Teller e alfa-s (as). A caracterização química dos AC foi realizada recorrendo-se a técnicas de análise elementar (AE) e espectroscopia de infravermelho com transformadas de Fourier (FTIR) e à determinação do ponto de carga zero. Os três carvões activados possuem valores de área superficial externa idênticos, o PET-2-700 possui o maior volume microporoso e o PET-2-700ox exibe o maior diâmetro de poros. Por outro lado, o PET-2-700ox possui um carácter fortemente ácido, o PET-2-700 exibe carácter ligeiramente ácido e o PET-2-700red apresenta propriedades ligeiramente alcalinas. Com base na AE, todas as amostras possuem percentagens de carbono elevadas, sendo que o PET-2-700red apresenta o valor mais elevado. Os resultados obtidos para a caracterização estrutural dos revelaram a obtenção de materiais mesoporosos de alta qualidade, definida pela elevada regularidade e uniformidade da estrutura porosa. A análise dos parâmetros de caracterização textura! permitiu inferir que os quatro materiais mesoporosos possuem valores de área superficial elevados, e que os materiais SBA-15 apresentam valores de volume poroso total e de tamanho de poros superiores aos manifestados pelos MCM-41. A incorporação de titânio não conduziu a uma perda significativa de qualidade dos materiais substituídos em relação às correspondentes amostras de sílica. Efectuaram-se estudos de adsorção em fase líquida de forma a avaliar a possível aplicação dos vários adsorventes na remoção de MCPA e de MB de efluentes líquidos. concluiu-se que o tempo de equilíbrio de 72 horas seria adequado e que a capacidade de adsorção dos vários AC era superior em meio ácido. Com base nas isotérmicas de adsorção do MCPA e do MB e na aplicação da representação de Langmuir e de Freundlich, foi possível concluir que o PET-2-700 possui a maior capacidade de adsorção do MCPA, 1.42 mmol/g, enquanto que o PET-2-700ox revelou a maior capacidade de adsorção do MB, 1.43 mmol/g. Na realidade, os materiais microporosos estudados apresentaram percentagens de remoção elevadas, tanto do MCPA como do MB. Relativamente aos materiais mesoporosos ordenados preparados neste trabalho, a percentagem de remoção de para os poluentes em estudo foi relativamente baixa, constatando-se que nesta fase dos estudos não constituem uma alternativa viável à utilização dos AC. No entanto, uma funcionalização criteriosa dos mesmos pode eventualmente proporcionar um aumento da capacidade adsortiva. ABSTRACT: The work presented in this master thesis, consisted of evaluating the potential use of different adsorbents materials, like activated carbon (AC) prepared by chemical activation with KOH, from recycled poly (ethylene terephthalate) (PET) and materials with ordered mesoporous structure such as MCM-41 and SBA-15, for removing acid 4-chlorine-2-metilfenoxiacétic and methylene blue from aqueous phase. We had prepared three microporous materials, PET-200-700, PET-2-700ox (AC oxidized) and PET-2-700red (reduced AC), two materials consisting exclusively of mesopores, Si-MCM-41 and Ti-MCM-41-50 and two materials containing mainly mesopores, but also having some microporosity, such as Si-SBA-15 and Ti-SBA-15-50. The textural characterization of the adsorbents was inferred by nitrogen adsorption at 77K and X-ray diffraction. Three methods were used to analyse the isotherms, namely, Dubinin-Radushkevich, Brunauer-Emmett-Teller and alpha-s (as). The chemical characterization of AC was performed using the elementary analysis, Fourier transform infrared spectroscopy (FTIR) and determination of the point of zero charge. Concerning the AC, the three present almost the same externa! surface area, PET-2-700 has a high micropore volume and PET-2-700ox shows the largest pore size diameter. On the other hand, PET-2-700ox had a strong acid character, PET-2-700 exhibits just a slightly acid character and PET-2-700red presents alkaline properties. The AE analysis allows confirming the high carbon content of theses AC, with PET-2-700red exhibiting the highest carbon proportion. The results from the structural characterization of the mesoporous materials, had disclosed the attainment of materials with high quality, defined by the raised regularity and uniformity of the porous structure. The analysis of the textural parameters allowed inferring that the four studied mesoporous materials possess high superficial area. The SBA-15 type materials present higher values of total porous volume and pores size diameter as the MCM-41. Also, the titanium incorporation did not lead to a significant loss of quality of the materials substituted in relation to the corresponding silica samples. The adsorption studies in liquid phase allow evaluating the possibility of using the different adsorbents for the MCPA and the MB removal. The kinetic studies had allowed to state the equilibrium time as 72 hours and a higher adsorption capacity was achieved in an acid medium. The influence of the pH of the medium, on the MCPA adsorption was evaluated. The MCPA and MB isotherms were analysed based on the Langmuir and Freundlich equation, the representations presented an excellent linearity, indicating the applicability of these equations to these systems. Also, it allows concluded that PET-2-700 had a higher adsorption capacity for MCPA, 1.42 mmol/g, and PET-2-700ox had a higher adsorption capacity for MB, 1.43 mmol/g. The AC used presented high removal percentages for MCPA and MB. Concerning the mesoporous materials prepared in this work, the percentage removal for the pollutants in study was relatively low, and evidencing that at the moment these mesoporous materials do not constitute a viable alternative to the AC. However, an astute funcionalisation of the same ones can, eventually provide an increase of the adsorption capacity.

EFFECT OF SALT REDUCTION ON THE SAFETY AND STABILITY OF TRADITIONAL BLOOD DRY-CURED SAUSAGES

Health issues such as cardiovascular disease are often due to dietary habits. Thus, meat industry needs to reduce salt in their products. However, production of low-salt content dry-cured not affected. The current study evaluated the effect of salt reduction from 6% to 3% in two Portuguese traditional blood dry-cured sausages. Physicochemical and microbiological parameters, biogenic amines content, fatty acids profile, texture profile analyses and sensory panel evaluations were considered. Differences due to salt reduction were noticeable in a faint increase in water activity, which slightly favoured microbial growth, with the highest yeasts numbers found in 6% salt sausages. Total biogenic amines content ranged from 224.72 to 1302.81 mg kg-1 dry matter, with higher amounts, particularly of cadaverine, histamine and tyramine, in low-salt products. Still, histamine significant differences were observed due to salt content. However, texture profile analysis revealed that low-salt products showed lower resilience and cohesiveness, even though no textural changes were observed by the panellists. Nevertheless, low-salt sausages were clearly preferred. Still, taking the safety of these traditional meat products into account, the results obtained for pH, aw and biogenic amines, have shown that a reduction in salt content should be accompanied by complementary safety measures, such as the use of starter cultures to minimise microbiological and chemical risks.

Characterization of medieval glass artefacts from Miranduolo site, Chiusdino, Italy

This archaeovitreological study deals with artefacts of Miranduolo site, Tuscany region (Italy), dated 1250-1350 AD. The Miranduolo site is a medieval hill-village dated from 7th to 14th century. The information obtained reveal that Miranduolo was under control of noble families, which displayed the social, economic and political power. It is marked by controlling the farmers and metal workers on the site, as well as having control over agricultural surpluses. No in situ glass workshop has been recovered, implying that the glass artefacts were imported. One aim of this work is application of SEM-EDS to visualize textural characteristics and thickness of the pristine glass and corrosion layers. Preliminary qualification and semi-quantification of major and minor chemical elements will provide the data on the glass group present and fluxes employed. The data obtained will be integrated with the one obtained by more sensitive techniques such as PIXE/PIGE and LA-ICP-MS. Twenty cross-sections of transparent glasses (colorless, azure, and different hues of yellow and) have been analyzed by VP-SEM. All the analyzed glasses display a homogenous matrix. Only four samples (MD 24, MD 139, MD 143, MD 259) show corrosion layers of various thickness with 2.25μm, 136-500 μm, 26.8 μm and 17.01 μm. EDS linescan analyses indicate strong depletion in the corrosion layers of Na and K, while Ca depletes to a minor extent. In general, both glass composition and the burial conditions were favorable for preservation. Samples can be classified as mainly plant ash Na-Ca-Si glasses made with both unpurified and purified Levantine ash. Only sample MD 243 is made from Barilla plant ash. Sample MD 139 cannot be classified into main compositional groups as K2O is 1.33 wt% and MgO 5.92 wt%. In 8 samples MnO content is lower than 0.8 wt%, meaning that in these samples MnO is naturally present. In other 12 samples, MnO above 0.8 wt% indicates deliberate addition as a decolorant agent to intentionally obtain different hues or the amount added was not successful in making the glass transparent. The results considering fluxes are compatible with archaeovitreological study from contemporary primary glass workshops in Tuscany. For determining the provenance of silica sources, further analysis with more sensitive techniques has to be carried out; Resumo: Este estudo “arqueovitreologia” lida com artefatos do local Miranduolo, região da Toscana (Itália), datados de 1250-1350 AD. O sitio de Miranduolo é uma colina vila medieval datada do séc.VII ao séc.XIV. As informações obtidas revelam que Miranduolo estava sob o controle de famílias nobres, que exibiu o poder social, económico e político. É marcado por controlar os agricultores e trabalhadores do metal no sitio, bem como ter controlo sobre os excedentes agrícolas. Não há na oficina de vidro in situ foi recuperado, o que implica que os artefactos de vidro foram importados. Um dos objetivos deste trabalho é a aplicação de SEM-EDS para visualizar características de textura e espessura das camadas de corrosão do vidro também como da áreas originais. qualificação preliminar e semi-quantificação de maiores e menores elementos químicos irá fornecer os dados sobre o grupo presente vidro e fluxos empregado. Os dados obtidos são integrados com os dados obtidos por meio de técnicas mais sensíveis, como PIXE / PIGE e LA-ICP-MS. Vinte secções transversais de vidros transparentes (incolor, azul celeste, e diferentes tons de amarelo) foram analisados por VP-SEM. Todos os vidros analisados exibir uma matriz homogénea. Apenas quatro amostras (MD 24, MD 139, MD 143, MD 259) mostram camadas de corrosão de várias espessuras com 2.25μm, 136-500μm, 26,8μm e 17,01μm. Análises Linescan EDS indicam forte esgotamento nas camadas de corrosão de Na e K, enquanto Ca esgota, em menor grau. Em geral, tanto a composição de vidro e as condições de depósito foram favoráveis para a preservação. As amostras podem ser classificados como vidros principalmente Na-Ca-Si feitas com cinzas de plantas do tipo levantino, não purificada e purificada. Apenas a amostra MD 243 é feita a partir de cinzas vegetais tipo “Barilla”. A amostra MD 139 não pode ser classificada em grupos principais de composição porque K2O é 1,33% em peso e MgO 5,92% em peso. Em 8 amostras, o teor de MnO é menor do que 0,8% em peso, o que significa que nestas amostras MnO está naturalmente presente. Em outras 12 amostras, MnO acima de 0,8% em peso indica adição intencional como um agente de colorante para obter intencionalmente diferentes matizes ou o valor acrescentado não foi bem sucedido em fazer o vidro transparente. Os resultados, considerando os fluxos são compatíveis com o estudo “arqueovitreologico” com as principais oficinas de vidro contemporâneos na Toscana. Para determinar a origem das fontes de sílica, uma análise mais aprofundada com técnicas mais sensíveis tem de ser levada a cabo.

ESTUDO DE CONDUTIVIDADE HIDRÁULICA EM SOLOS DE SAVANA ENCONTRADOS EM ÁREAS A MARGEM DREITA DO CÓRREGO DA ONÇA, MUNICÍPIO DE UBERLÂNDIA/ MG/ BR

Por suas características físicas, principalmente textura e estrutura, os oxissolos, solos evoluídos e amplamente intemperizados das regiões de savana (cerrado) no Brasil, apresentam boas condições de circulação de fluídos, o que de certa forma os tornam vulneráveis ‘a processos de contaminação. Um dos parâmetros utilizados na análise de vulnerabilidade é o conhecimento do comportamento da condutividade hidráulica e que constitui o objetivo desse trabalho. A área de estudo localiza-se na micro-bacia do córrego da Onça, município de Uberlândia, Minas Gerais, Brasil. Na determinação dos valores de condutividade hidráulica em superfície e em profundidade foram utilizadas respectivamente nessa ordem as técnicas de anéis concêntricos e open end hole. Os valores de condutividade hidráulica de superfície nos pontos amostrados variaram entre 1x10-5 9x10-5. Os valores de condutividade nas profundidades de 0,5, 1,0, 1,5 e 2,0 m variaram entre 4,1x10-6 a 2,5x10-5. A análise textural e respectivo enquadramento no triângulo textural, indicam composição argilosa dos solos nas diferentes profundidades. Materiais com condutividade hidráulica acima de 1x10-7 são considerados permeáveis, sendo assim, constata-se que esses solos estão sujeitos a contaminação química, seja ela de forma direta, por uso agrícola ou resíduos das atividades urbanas.