Efeitos do treinamento isocinético e isométrico sobre a taxa de desenvolvimento de força máxima

The objective of the present study was to compare the effects of a high speed isokinetic training (180°.s-1) and an isometric training (75°) on the maximum rate of force development (RFDmax) measured in the isokinetic and isometric modes. Twenty seven male non active subjects participated of this study (Mean + SD = body mass 78.6 + 14.1 kg; stature 175.1 + 8.9 cm; age 22.6 + 3.8 years). They were randomly divided into three groups: Control (GC); Isokinetic training (GISOC) and; Isometric training (GISOM). The subjects were submitted in different days to the following pre training protocols: 1) Familiarization to the isokinetic dynamometer tests; 2) Five maximum concentric isokinetic contractions of the knee extensors (180°.s-1) to access the maximum concentric torque (TMC) and the concentric RFDmax; 3) Two maximum isometric contractions of the knee extensors (75°) to access the maximum isometric torque (TMI) and the isometric RFDmax. The same tests were repeated after the training period, but without the familiarization session. Eighteen training sessions were performed (3 times per week). The GISOC performed the entire training whit concentric isokinetic contractions whit the speed of 180°.s-1. The GISOM performed the entire training whit isometric contractions whit the angle between the thigh end the leg being 75° (0° = full knee extension). TMI, TMC, concentric RFDmax, isometric RFDmax values of the GC was not different between pre and post training. GISOM increased only the TMI and the GSIOC increased the TMC, concentric RFDmax and isometric RFDmax. Furthermore, the GISOC had a higher percentage increase of the isometric RFDmax than the isokinetic RFDmax. Based on these results, it is possible to conclude that the increase in maximum strength corresponded to the training specificity theory, unlike to the RFDmax. Thus the use of isometric contraction ...(Complete abstract click electronic access below)

Análise de algoritmos computacionais utilizados em sistemas de planejamento de braquiterapia de alta taxa de dose: estudo comparativo com o Código MCNP-5C

In radiotherapy, computational systems are used for radiation dose determination in the treatment’s volume and radiometric parameters quality analysis of equipment and field irradiated. Due to the increasing technological advancement, several research has been performed in brachytherapy for different computational algorithms development which may be incorporated to treatment planning systems, providing greater accuracy and confidence in the dose calculation. Informatics and information technology fields undergo constant updating and refinement, allowing the use Monte Carlo Method to simulate brachytherapy source dose distribution. The methodology formalization employed to dosimetric analysis is based mainly in the American Association of Physicists in Medicine (AAPM) studies, by Task Group nº 43 (TG-43) and protocols aimed at dosimetry of these radiation sources types. This work aims to analyze the feasibility of using the MCNP-5C (Monte Carlo N-Particle) code to obtain radiometric parameters of brachytherapy sources and so to study the radiation dose variation in the treatment planning. Simulations were performed for the radiation dose variation in the source plan and determined the dosimetric parameters required by TG-43 formalism for the characterization of the two high dose rate iridium-192 sources. The calculated values were compared with the presents in the literature, which were obtained with different Monte Carlo simulations codes. The results showed excellent consistency with the compared codes, enhancing MCNP-5C code the capacity and viability in the sources dosimetry employed in HDR brachytherapy. The method employed may suggest a possible incorporation of this code in the treatment planning systems provided by manufactures together with the equipment, since besides reducing acquisition cost, it can also make the used computational routines more comprehensive, facilitating the brachytherapy ...

Equações de taxa aplicadas na modelagem de dispositivos fotodetectores baseados em poços quânticos

In this work, it is presented a novel method for calculating some intrinsic parameters such as capture mean time, thermic emission mean time, capture probability and noise gain on quantum well infrared photodetectors. Such devices are built by depositing layers of semiconductors of different energy gap, forming quantum wells. The present method uses rate equations to describe the occupation of discrete states of the quantum wells, that together with noise gain equations given in literature, are solved self consistently. The input data of the method is experimental measurement of dark current (current measured with no relevant incident photon) versus applied bias. In order to validate this approach, the values obtained were compared with results from literature

Esportes de risco: perspectivas da psicologia do esporte na concepção do prazer

Com o ritmo acelerado que a vida moderna exige, é cada vez mais evidente a necessidade do ser humano em buscar novas experiências para que os façam sentir emoções e sensações inéditas, não existentes no dia a dia. Com isso a busca por esportes de risco vem sendo cada vez maior, visto que muitos destes esportes satisfazem os desejos por novas experiências. Acredita-se que haja inúmeros fatores atrativos que levam os indivíduos a aderirem a essas praticas. No presente estudo foi verificado que fatores psicológicos estão fortemente presentes, o medo e a ansiedade mostram-se fatores atrativos, assim como o desejo de conhecer lugares novos, o que aponta para uma ligação direta com o turismo. A sensação de bem estar, satisfação, alegria e orgulho foi afirmada por maioria dos sujeitos, o que acaba levando os indivíduos a procurarem diversos esportes de risco, favorecendo a aderência a essas modalidades e a permanência nas mesmas.

A concepção do aluno sobre o papel da educação física na escola após a experiência de acampante

Camping alloys the implementation of a broad variety of activities that involves many aspects of the corporal culture of movement. There is much more than fun in games and plays and that’s what we seek to include in the children’s daily routine. The Physical Education professional has as one of its duties to teach these elements, such as the knowledge related to the citizenship formation to its students. Therefore, the participation in camping can contribute to this formation, since the students have the chance to realize the amplitude of Physical Education and change their view on it, even at school. The aim of this research is to investigate after the camping experience, if the students change their conception on the Physical Education role at school. This study has used qualitative methodology consisting on interviews done prior and post the students camping experience at the school . Ten students of both gender, aged between 13 and 15 years old, were interviewed. It was used a script with semi-structured questions. As the main result it has found an unanimity among the students towards the importance of Physical Education: the responsibility for the health and it’s also arisen discussions on cooperation and respect. Although they recognize that the teacher does not discuss these values and attitudes; two students believe that to have changed their view towards school Physical Education after experiencing the activities proposed in the camping. Despite most of the students haven’t changed their concept on school Physical Education, they had the opportunity to see new activities and to think more carefully about the importance of Physical Education classes at school, an opportunity on building a more critical view on the discipline.

Treinamento de força unilateral: efeitos sobre a taxa de desenvolvimento de força do membro contralateral

The aim of this study was to analyze the effects of unilateral isokinetic strength training at high speed (180°.s-1) of the dominant leg on the rate of force development (RFD) of the contralateral limb. The study included 18 male individuals, apparently healthy, with an average of 23 years, and without regular practice of physical activities. The subjects were divided randomly into two groups: control group (GC) and isokinetic group (GISOC). Assessments were made of the values of peak isometric torque (PT isom) and RFD of both lower limbs in the pre-training. So, the GISOC underwent an isokinetic strength training with high speed (180°.s-1) for 6 weeks, with the dominant leg only and then reassessed. It was found that there was no significant improvement in value of PT isom (p> 0.05), and the RFD for the dominant limb had a significant improvement (p< 0.05) compared to the pre-training and that there was no transfer of values to the contralateral side (p> 0.05). It can be concluded that the isokinetic training at high speed was not enough for significant cross education

Confecção e caracterização de filmes finos de boro para a medida da taxa de reação 10B(N, a)7LI na terapia por captura de nêutrons pelo boro

The Boron Neutron Capture Therapy (BNCT), based on the 10B(n,α)7Li reaction, represents a promising modality for the treatment of cancers that are resistents to conventional treatments. So, it is necessary to find drugs (boron compounds) with high selectivity for each type of cancer, the neutrons source should be well characterized and the rate of 10B(n,α)7Li reaction should be measured with great accuracy as possible. This study aimed to develop a method for manufacturing thin films of boron, for measure the 10B(n,α)7Li reaction, and analyze the uniformity of the films. Five thin films of boron were manufactured with three different concentrations of boric acid, heated to transform the acid in boron, irradiated with thermic neutrons coupled to CR-39 detectors, in BNCT line at the reactor IEA-R1 IPEN/CNEN, São Paulo. After the irradiation, the detectors were chemically attacked with NaOH to reveal the tracks. The methodology presented is effective because it resulted in deposition of boron as thin film enabling the quantitative analysis of 10B(n,α)7Li reaction. The analysis of the uniformity of density of the induced tracks in CR-39 shows that, in most of the films, there is no uniformity in surface distribution of boron, but when the film is divided, we obtain some uniform sectors

Correlação entre aneuploidia cromossômica em espermatozóides e taxa de implantação embrionária: subtitulo

Infertility is directly related to chromosomal abnormalities in germ cells. Among them, the aneuploidies are the most frequent chromosomal abnormalities and responsible for embryo implantation failures, miscarriages, fetal losses and newborns with congenital malformations, mental disability and neuropsychomotor developmental delay. Male patients with normal somatic karyotype may present different rates of aneuploidies in sperm, resulting in abnormal embryos. This study aimed to correlate the frequency of chromosomal aneuploidies in spermatozoa with embryo implantation rate in couples undergoing assisted reproductive techniques. The methodology has included chromosomal analysis by GTG banding and molecular cytogenetic study using Fluorescent In Situ Hybridization technique for evaluation of chromosomes 9, X and Y in germ cells of 22 patients referred to the Human Reproduction Service of the Clinical Hospital FMRP-USP. Embryo implantation rates were determined by hormonal evaluation in maternal peripheral blood and ultrasound confirmation. Two patients presented abnormal karyotype, characterized by polymorphism of the heterochromatic region of the long arm of chromosome 9 and a satellite in the short arm of chromosome 22. Both alterations, usually considered variants of normality, have been related to infertility phenotype and miscarriages. Significant differences were detected between couples who presented pregnancy (group 1) and couples with embryo implantation failure (group 2), with higher frequency of aneusomy and diploidy of chromosome 9, as well as total aneuploidy in sperm of group 2 patients. Our results suggest a correlation between aneuploidy and embryo implantation rates, since the infertile group with reproductive failure has showed higher frequency of aneuploidy. Screening for aneuploidies detection in male germ cells should be included in order to decrease embryo implantation failures, miscarriages and fetuses with chromosomal ...

Avaliação da influência da taxa de resfriamento posterior ao tratamento térmico nas propriedades mecânicas do aço API 5L X70

In this work a study about the mechanical properties of the API 5L X70 steel, with or without heat treating, has been made, with the intetion of assess the influence of cooling after the austenitization heat treating by air cooling (normalizing) and a rapid cooling with oil (tempering). This steel is known by high strength and ductility values and it is commonly used in the manufacture of oil pipes. The growing energy demand encouraged the study and manufacture of this material. Although this microalloyed dispense subsequent heat treatings, it was proven that its implementation is very advantageous for this type of application, improving hardness and plastic stability. It was also assessed that the faster the cooling rate is, the better will be these properties

Estudo, desenvolvimento e concepção de uma célula de carga

In engineering projects, it’s fundamental to determine the active loads in components in order to guarantee acceptable values of safety and reliability according to project specifications. On the other hand, force measurement methods might be very complex and impracticable in some cases and, so that, load cells with eletric resistance strain gages can be applied as a simple and accurate option to measure the required load. The main purpose of this paper is to present the development of a load cell that measures uniaxial forces using electric resistance strain gages without being influenced by the location of the loading in a cantilever beam. For that, it was taken as basis a secondary purpose which is to present a general study of basic and wide concepts about transducers, load cells and extensometers primarily. Information such as: loading and measurements types, characteristics of the presented devices as well as factors that influence its functioning, the most common kinds of Wheatstone bridge links, the main points of a load cell project, cements used to fix extensometers and, finally, the project itself with the tests of the built transducer are presented. By the end of this paper, all the results are shown and analyzed, concluding about the designed load cell and the work itself

Efeitos do exercício aeróbio prévio sobre a taxa de desenvolvimento de força em indivíduos ativos

Clicar acesso eletrônico abaixo.

Competitividade internacional: uma análise dinâmica das exportações brasileiras frente à taxa de câmbio e aos estímulos governamentais no período recente

Não disponível

Parque Urbano – Arte e Educação Ambiental a partir de uma concepção lúdica

Não disponível

Análise macro e micrográfica da liga AA-356 conforme a taxa de resfriamento

The present work aims to study the characteristics of the alloy Al - 7 % Si - 0 , 3Mg ( AA356 ) , more specifically characterize the macrostructure and microstructure and mechanical properties of the alloy ingots AA356 obtained in metal molds and sand molds for power studying the structures through the difference of cooling rates . This alloy is explained by the fact of referring league has excellent combination of properties such as low solidification shrinkage and good fluidity, good weldability , high wear resistance , high strength to weight ratio, has wide application in general engineering , and particularly in the automotive and aerospace engineering . In this work we will verify this difference in properties through two different cooling rates . We monitor the solid solidification temperatures by thermocouples building with them the cooling curve as a tool that will aid us to evaluate the effectiveness of the grain refining because it achieved with some important properties of the alloy as the latent heat of solidification fraction the liquid and solid temperatures, the total solidification time, and identify the presence of inoculants for grain refinement. Thermal analysis will be supported by the study of graphic software “Origin “will be achieved where the cooling curve and its first derivative that is the cooling rate. Made thermal analysis, analysis will be made in macrographs ingots obtained for observation of macrostructures obtained in both types of ingots and also analysis of micrographs where sampling will occur in strategic positions ingots to correlate with the microstructure. Finally will be collecting data from Brinell hardness of ingots and so then correlating the properties of their respective ingots with cooling rate. We found that obtained with cast metal ingots showed superior properties to the ingots obtained with sand mold

A influência do alongamento prévio no pico de torque e na taxa de desenvolvimento de força

The objective of this study was to investigate the influence of previous active static stretch on the peak torque (PT) and rate of force development (TDF) during isokinetic concentric contractions at 60 and 180.s-1 in active individuals. Twelve active subjects with ages between 18 and 30 years participated of this study. The individuals were submitted in different days to the following tests: 1) Familiarization session to the isokinetic dynamometer; 2) Five maximal isokinetic concentric contractions for knee extensors at each angular velocity (60 and 180.s-1) to determine PT and TDF (Control), and; 3) Two active static stretching exercises for the dominant leg extensors (10 x 30 s for each exercise, with 20 s of rest). After the stretching, the isokinetic test was repeated (Post-Stretching). The conditions 2 and 3 were performed in random order. There was no significant modification after the stretch exercises on the PT, angle and time at which the PT was attained, at 60 and 180º.s-1. In the same way, there was no significant modification on the TDF and angle at which the maximal TDF was attained in both angular speeds. In other way, the time to attain maximal TDF (TTDF) at 180º.s-1 was significantly lower after the stretching (Pre - 98.3 ± 27.5 ms and Post - 86.6 ± 30.2 ms). There was significant modification on the torque (60 and 180º.s-1) and time (60º.s-1) at different delta of angle variations, obtained at 60º.s-1 at Control and Post-Stretching conditions. However, there was significant reduction of time after the stretching exercises on delta of angle variations of 90-88º (Pre - 46.6 ± 6.5 ms and Post - 44.1 ± 5.1 ms), 88-85º (Pre - 65.8 ± 7.9 ms and Post - 63.3 ± 4.9 ms) and 85-80º (Pre - 93.3 ± 7.7 ms and Post - 90.0 ± 4.2 ms) at 180º.s-1. With base on these data, it is possible to conclude that PT and TDF do not modify after static stretching, irrespectively on the speed...(Complete abstract click electronic access below)