Impact of E22 on two-stroke and four-stroke snowmobiles

A push to reduce dependency on foreign energy and increase the use of renewable energy has many gas stations pumping ethanol blended fuels. Recreational engines typically have less complex fuel management systems than that of the automotive sector. This prevents the engine from being able to adapt to different ethanol concentrations. Using ethanol blended fuels in recreational engines raises several consumer concerns. Engine performance and emissions are both affected by ethanol blended fuels. This research focused on assessing the impact of E22 on two-stroke and four-stroke snowmobiles. Three snowmobiles were used for this study. A 2009 Arctic Cat Z1 Turbo with a closed-loop fuel injection system, a 2009 Yamaha Apex with an open-loop fuel injection system and a 2010 Polaris Rush with an open-loop fuel injection system were used to determine the impact of E22 on snowmobile engines. A five mode emissions test was conducted on each of the snowmobiles with E0 and E22 to determine the impact of the E22 fuel. All of the snowmobiles were left in stock form to assess the effect of E22 on snowmobiles currently on the trail. Brake specific emissions of the snowmobiles running on E22 were compared to that of the E0 fuel. Engine parameters such as exhaust gas temperature, fuel flow, and relative air to fuel ratio (λ) were also compared on all three snowmobiles. Combustion data using an AVL combustion analysis system was taken on the Polaris Rush. This was done to compare in-cylinder pressures, combustion duration, and location of 50% mass fraction burn. E22 decreased total hydrocarbons and carbon monoxide for all of the snowmobiles and increased carbon dioxide. Peak power increased for the closed-loop fuel injected Arctic Cat. A smaller increase of peak power was observed for the Polaris due to a partial ability of the fuel management system to adapt to ethanol. A decrease in peak power was observed for the open-loop fuel injected Yamaha.

Understanding Michigan nonindustrial private forest landowners attitudes and knowledge about forest management

Approximately one-fourth of the non-industrial private forestland (NIPF) owners in the state of Michigan, who collectively own approximately 50% of the private forested land, have conducted commercial timber harvest in recent years. Previous studies indicated that NIPFs preferred to manage their forest for a sustained yield of high-quality timber, but were limited to even-aged regeneration treatments or conversion for uneven-aged silviculture due to previous cuttings. Improved knowledge about NIPF’s intentions and forest management behavior could be useful for successful implementation of sustained yield management. This study’s objective was to identify more active NIPF’s attitudes towards timber management, their forest management practices and whether their forest management behavior leads or leads not to q management for sustained yield. Active NIPF’s intentions to harvest timber for biofuels and its suitability with NIPF’s forest management behavior will be discussed. Phone interviews of 30 NIPFs who have experience with commercial timber harvests were conducted between August and October 2011. All interviews were recorded, transcribed, and analyzed for identifying NIPF’s motivations, attitudes, forest management behavior and forestry related knowledge. Interviewees, whether consciously or not, tended to manage their land for a sustained yield and they would be willing to harvest timber for biofuels facility as long as it benefits landowners management goals.

Control design and genetic algorithm optimization for electrostatic MEMS

This dissertation discusses structural-electrostatic modeling techniques, genetic algorithm based optimization and control design for electrostatic micro devices. First, an alternative modeling technique, the interpolated force model, for electrostatic micro devices is discussed. The method provides improved computational efficiency relative to a benchmark model, as well as improved accuracy for irregular electrode configurations relative to a common approximate model, the parallel plate approximation model. For the configuration most similar to two parallel plates, expected to be the best case scenario for the approximate model, both the parallel plate approximation model and the interpolated force model maintained less than 2.2% error in static deflection compared to the benchmark model. For the configuration expected to be the worst case scenario for the parallel plate approximation model, the interpolated force model maintained less than 2.9% error in static deflection while the parallel plate approximation model is incapable of handling the configuration. Second, genetic algorithm based optimization is shown to improve the design of an electrostatic micro sensor. The design space is enlarged from published design spaces to include the configuration of both sensing and actuation electrodes, material distribution, actuation voltage and other geometric dimensions. For a small population, the design was improved by approximately a factor of 6 over 15 generations to a fitness value of 3.2 fF. For a larger population seeded with the best configurations of the previous optimization, the design was improved by another 7% in 5 generations to a fitness value of 3.0 fF. Third, a learning control algorithm is presented that reduces the closing time of a radiofrequency microelectromechanical systems switch by minimizing bounce while maintaining robustness to fabrication variability. Electrostatic actuation of the plate causes pull-in with high impact velocities, which are difficult to control due to parameter variations from part to part. A single degree-of-freedom model was utilized to design a learning control algorithm that shapes the actuation voltage based on the open/closed state of the switch. Experiments on 3 test switches show that after 5-10 iterations, the learning algorithm lands the switch with an impact velocity not exceeding 0.2 m/s, eliminating bounce.

THERMAL CHARACTERIZATION OF A GASOLINE TURBOCHARGED DIRECT INJECTION (GTDI) ENGINE UTILIZING LEAN OPERATION AND EXHAUST GAS RECIRCULATION (EGR)

The push for improved fuel economy and reduced emissions has led to great achievements in engine performance and control. These achievements have increased the efficiency and power density of gasoline engines dramatically in the last two decades. With the added power density, thermal management of the engine has become increasingly important. Therefore it is critical to have accurate temperature and heat transfer models as well as data to validate them. With the recent adoption of the 2025 Corporate Average Fuel Economy(CAFE) standard, there has been a push to improve the thermal efficiency of internal combustion engines even further. Lean and dilute combustion regimes along with waste heat recovery systems are being explored as options for improving efficiency. In order to understand how these technologies will impact engine performance and each other, this research sought to analyze the engine from both a 1st law energy balance perspective, as well as from a 2nd law exergy analysis. This research also provided insights into the effects of various parameters on in-cylinder temperatures and heat transfer as well as provides data for validation of other models. It was found that the engine load was the dominant factor for the energy distribution, with higher loads resulting in lower coolant heat transfer and higher brake work and exhaust energy. From an exergy perspective, the exhaust system provided the best waste heat recovery potential due to its significantly higher temperatures compared to the cooling circuit. EGR and lean combustion both resulted in lower combustion chamber and exhaust temperatures; however, in most cases the increased flow rates resulted in a net increase in the energy in the exhaust. The exhaust exergy, on the other hand, was either increased or decreased depending on the location in the exhaust system and the other operating conditions. The effects of dilution from lean operation and EGR were compared using a dilution ratio, and the results showed that lean operation resulted in a larger increase in efficiency than the same amount of dilution with EGR. Finally, a method for identifying fuel spray impingement from piston surface temperature measurements was found. Note: The material contained in this section is planned for submission as part of a journal article and/or conference paper in the future.

Case Study of a Children's Judo Class: Musculoskeletal Fitness Changes

We evaluated the musculoskeletal fitness changes in 18 children enrolled in the Montana Tech Fall Judo Camp (test sample) and 12 children from a 3rd grade class at a local elementary school in Butte, Montana (control sample). The musculoskeletal fitness tests included push-up test, pull-up test, and one-minute timed sit-ups for the test sample and push-ups and one minute timed sit-ups for the control sample, with five minutes of rest between each test. The test sample increased their performances in pull-ups, sit-ups, and push-ups by 07, 3.7, and 6.6 repetitions, respectively. The control sample decreased in their sit-up performance by 1.3 repetitions, and improved their push-up performance by 0.2 repetitions. These results show that the test sample improved their musculoskeletal fitness as measured fitness as measured by these tests.

Structural characterization and reliable biomechanical assessment of integrative cartilage repair

Structural and functional characterization of integrative cartilage repair in controlled model systems can play a key role in the development of innovative strategies to improve the long-term outcome of many cartilage repair procedures. In this work, we first developed a method to reproducibly generate geometrically defined disk/ring cartilage composites and to remove outgrown fibrous layers which can encapsulate cartilaginous tissues during culture. We then used the model system to test the hypothesis that such fibrous layers lead to an overestimation of biomechanical parameters of integration at the disk/ring interface. Transmission electron microscopy images of the composites after 6 weeks of culture indicated that collagen fibrils in the fibrous tissue layer were well integrated into the collagen network of the cartilage disk and ring, whereas molecular bridging between opposing disk/ring cartilage surfaces was less pronounced and restricted to regions with narrow interfacial regions (< 2 microm). Stress-strain profiles generated from mechanical push-out tests for composites with the layers removed displayed a single and distinct peak, whereas profiles for composites with the layers left intact consisted of multiple superimposed peaks. As compared to composites with removed layers, composites with intact layers had significantly higher adhesive strengths (161+/-9 vs. 71+/-11 kPa) and adhesion energies (15.0+/-0.7 vs. 2.7+/-0.4 mJ/mm2). By combining structural and functional analyses, we demonstrated that the outgrowing tissue formed during in vitro culture of cartilaginous specimens should be eliminated in order to reliably quantify biomechanical parameters related to integrative cartilage repair.

Subcutaneous immunoglobulin: opportunities and outlook

Immunoglobulin (Ig) administration via the subcutaneous (s.c.) route has become increasingly popular in recent years. The method does not require venous access, is associated with few systemic side effects and has been reported to improve patients' quality of life. One current limitation to its use is the large volumes which need to be administered. Due to the inability of tissue to accept such large volumes, frequent administration at multiple sites is necessary. Most studies conducted to date have investigated the use of subcutaneous immunoglobulin (SCIg) in patients treated previously with the intravenous (i.v.) formulation. New data now support the use of s.c. administration in previously untreated patients with primary immunodeficiencies. SCIg treatment may further be beneficial in the treatment of autoimmune neurological conditions, such as multi-focal motor neuropathy; however, controlled trials directly comparing the s.c. and i.v. routes are still to be performed for this indication. New developments may further improve and facilitate the s.c. administration route. For example, hyaluronidase-facilitated administration increases the bioavailability of SCIg, and may allow for the administration of larger volumes at a single site. Alternatively, more concentrated formulations may reduce the volume required for administration, and a rapid-push technique may allow for shorter administration times. As these developments translate into clinical practice, more physicians and patients may choose the s.c. administration route in the future.

What is the Relation between Human Practical Action and an Accompanying Discourse? Discussing the Status of Practical Theory

The article discusses the function of an accompanying discourse in relation to the genesis of human practical action. On the one side, theory cannot be taken as the ground for practical action; practical action is not a realisation of intentions. On the other hand, human practical action is accompanied by series of explanations, justifications, declarations of intent, pre‑ and post-rationalisations, motivations etc. These accompanying discourses seem in one way or the other to be necessary for the actual realisation of human practical action. Following Pierre Bourdieu, it is suggested that an accompanying discourse cannot in a meaningful manner be separated from the human practical action, that practical theory should be regarded not as theory but as part of practice, and that practical theory first of all provides a common language for talking about practice and hence for reproducing a fundamentally arbitrary idea of the genesis of human practical action. Parallels are drawn to the education/formal training of semi-professionals.

A Critical Response to Kevin Stenson’s Governing the Local: Sovereignty, Social Governance and Community Safety

In his compelling case study of local governance and community safety in the UK Thames Valley, Kevin Stenson makes several important contributions to the field of governmentality studies. While the paper’s merits are far-reaching, to this reader’s assessment they can be summarized in the following key areas: 1) Empirically, the article enhances our knowledge of the political economic transformation of a region otherwise overlooked in social science research ; 2) Conceptually, Stenson offers several theoretical and analytical refrains that, while becoming increasingly commonplace, are nonetheless still germane and rightly oriented to offer push back against otherwise totalizing, reified accounts of roll back/roll out neoliberalism. A welcomed new approach is offered as a corrective, The Realist Governmentality perspective, which emphasizes the interrelated and co-constitutive nature of politics, local culture, and habitus in processes related to the restructuring of social governance; 3) Methodologically, the paper makes a pitch for the ways in which finely grained, nuanced, mixed-method/ethnographic analyses have the potential to further problematize and recast a field of governmentality studies far too often dominated by discursive and textual approaches.

The Car Resequencing Problem with Pull-Off Tables

The car sequencing problem determines sequences of different car models launched down a mixed-model assembly line. To avoid work overloads of workforce, car sequencing restricts the maximum occurrence of labor-intensive options, e.g., a sunroof, by applying sequencing rules. We consider this problem in a resequencing context, where a given number of buffers (denoted as pull-off tables) is available for rearranging a stirred sequence. The problem is formalized and suited solution procedures are developed. A lower bound and a dominance rule are introduced which both reduce the running time of our graph approach. Finally, a real-world resequencing setting is investigated.

Transapical access closure: the TA PLUG device

OBJECTIVES Percutaneous closure of the transapical (TA) access site for large-calibre devices is an unsolved issue. We report the first experimental data on the TA PLUG device for true-percutaneous closure following large apical access for transcatheter aortic valve implantation. METHODS The TA PLUG, a self-sealing full-core closure device, was implanted in an acute animal study in six pigs (60.2 ± 0.7 kg). All the pigs received 100 IU/kg of heparin. The targeted activated clotting time was left to normalize spontaneously. After accessing the left ventricular apex with a 39 French introducer, the closure plug device was delivered with a 33 French over-the-wire system under fluoroscopic guidance into the apex. Time to full haemostasis as well as rate of bleeding was recorded. Self-anchoring properties were assessed by haemodynamic push stress under adrenalin challenge. An additional feasibility study was conducted in four pigs (58.4 ± 1.1 kg) with full surgical exposure of the apex, and assessed device anchoring by pull-force measurements with 0.5 Newton (N) increments. All the animals were electively sacrified. Post-mortem analysis of the heart was performed and the renal embolic index assessed. RESULTS Of six apical closure devices, five were correctly inserted and fully deployed at the first attempt. One became blocked in the delivery system and was placed successfully at the second attempt. In all the animals, complete haemostasis was immediate and no leak was recorded during the 5-h observation period. Neither leak nor any device dislodgement was observed under haemodynamic push stress with repeated left ventricular peak pressure of up to 220 mmHg. In the feasibility study assessing pull-stressing, device migration occurred at a force of 3.3 ± 0.5 N corresponding to 247.5 mmHg. Post-mortem analyses confirmed full expansion of all devices at the intended target. No macroscopic damage was identified at the surrounding myocardium. The renal embolic index was zero. CONCLUSIONS True-percutaneous left ventricular apex closure following large access is feasible with the self-sealing TA PLUG. The device allows for immediate haemostasis and a reliable anchoring in the acute animal setting. This is the first report of a true-percutaneous closure for large-calibre transcatheter aortic valve implantation access.

GATA-4 and GATA-6 modulate tissue-specific transcription of the human gene for P450c17 by direct interaction with Sp1.

Cytochrome P450c17 catalyzes steroidogenic 17alpha-hydroxylase and 17,20 lyase activities. Expression of the gene for P450c17 is cAMP dependent, tissue specific, developmentally programmed, and varies among species. Binding of Sp1, Sp3, and NF1-C (nuclear factor 1-C) to the first 227 bp of 5'flanking DNA (-227/LUC) is crucial for basal transcription in human NCI-H295A adrenal cells. Human placental JEG-3 cells contain Sp1, Sp3, and NF1, but do not express -227/LUC, even when transfected with a vector expressing steroidogenic factor 1 (SF-1). Therefore, other factors are essential for basal expression of P450c17. Deoxyribonuclease I footprinting and EMSAs identified a GATA consensus site at -64/-58 and an SF-1 site at -58/-50. RT-PCR identified GATA-4, GATA-6, and SF-1 in NCI-H295A cells and GATA-2 and GATA-3, but not GATA-4, GATA-6, or SF-1 in JEG-3 cells. Cotransfection of either GATA-4 or GATA-6 without SF-1 activated -227/LUC in JEG-3 cells, but cotransfection of GATA-2 or GATA-3 with or without SF-1 did not. Surprisingly, mutation of the GATA binding site in -227/LUC increased GATA-4 or GATA-6 induced activity, whereas mutation of the Sp1/Sp3 site decreased it. Furthermore, promoter constructs including the GATA site, but excluding the Sp1/Sp3 site at -196/-188, were not activated by GATA-4 or GATA-6, suggesting an interaction between Sp1/Sp3 and GATA-4 or GATA-6. Glutathione-S-transferase pull-down experiments and coimmunoprecipitation demonstrated interaction between GATA-4 or GATA-6 and Sp1, but not Sp3. Chromatin immunoprecipitation assays confirmed that this GATA-4/6 interaction with Sp1 occurred at the Sp site in the P450c17 promoter in NCI-H295A cells. Demethylation with 5-aza-2-deoxycytidine permitted JEG-3 cells to express endogenous P450c17, SF-1, GATA-4, GATA-6, and transfected -227/LUC. Thus, GATA-4 or GATA-6 and Sp1 together regulate expression of P450c17 in adrenal NCI-H295A cells and methylation of P450c17, GATA-4 and GATA-6 silence the expression of P450c17 in placental JEG-3 cells.

Physical and functional interaction between the dopamine transporter and the synaptic vesicle protein synaptogyrin-3.

Uptake through the dopamine transporter (DAT) represents the primary mechanism used to terminate dopaminergic transmission in brain. Although it is well known that dopamine (DA) taken up by the transporter is used to replenish synaptic vesicle stores for subsequent release, the molecular details of this mechanism are not completely understood. Here, we identified the synaptic vesicle protein synaptogyrin-3 as a DAT interacting protein using the split ubiquitin system. This interaction was confirmed through coimmunoprecipitation experiments using heterologous cell lines and mouse brain. DAT and synaptogyrin-3 colocalized at presynaptic terminals from mouse striatum. Using fluorescence resonance energy transfer microscopy, we show that both proteins interact in live neurons. Pull-down assays with GST (glutathione S-transferase) proteins revealed that the cytoplasmic N termini of both DAT and synaptogyrin-3 are sufficient for this interaction. Furthermore, the N terminus of DAT is capable of binding purified synaptic vesicles from brain tissue. Functional assays revealed that synaptogyrin-3 expression correlated with DAT activity in PC12 and MN9D cells, but not in the non-neuronal HEK-293 cells. These changes were not attributed to changes in transporter cell surface levels or to direct effect of the protein-protein interaction. Instead, the synaptogyrin-3 effect on DAT activity was abolished in the presence of the vesicular monoamine transporter-2 (VMAT2) inhibitor reserpine, suggesting a dependence on the vesicular DA storage system. Finally, we provide evidence for a biochemical complex involving DAT, synaptogyrin-3, and VMAT2. Collectively, our data identify a novel interaction between DAT and synaptogyrin-3 and suggest a physical and functional link between DAT and the vesicular DA system.

Dissecting the Interaction between p53 and TRIM24

Dissecting the Interaction of p53 and TRIM24 Aundrietta DeVan Duncan Supervisory Professor, Michelle Barton, Ph.D. p53, the “guardian of the genome”, plays an important role in multiple biological processes including cell cycle, angiogenesis, DNA repair and apoptosis. Because it is mutated in over 50% of cancers, p53 has been widely studied in established cancer cell lines. However, little is known about the function of p53 in a normal cell. We focused on characterizing p53 in normal cells and during differentiation. Our lab recently identified a novel binding partner of p53, Tripartite Motif 24 protein (TRIM24). TRIM24 is a member of the TRIM family of proteins, defined by their conserved RING, B-box, and coiled coil domains. Specifically, TRIM24 is a member of the TIF1 subfamily, which is characterized by PHD and Bromo domains in the C-terminus. Between the Coiled-coil and PHD domain is a linker region, 437 amino acids in length. This linker region houses important functions of TRIM24 including it’s site of interaction with nuclear receptors. TRIM24 is an E3-ubiquitin ligase, recently discovered to negatively regulate p53 by targeting it for degradation. Though it is known that Trim24 and p53 interact, it is not known if the interaction is direct and what effect this interaction has on the function of TRIM24 and p53. My study aims to elucidate the specific interaction domains of p53 and TRIM24. To determine the specific domains of p53 required for interaction with TRIM24, we performed co-immuoprecipitation (Co-IP) with recombinant full-length Flag-tagged TRIM24 protein and various deletion constructs of in vitro translated GST-p53, as well as the reverse. I found that TRIM24 binds both the carboxy terminus and DNA binding domain of p53. Furthermore, my results show that binding is altered when post-translational modifications of p53 are present, suggesting that the interaction between p53 and TRIM24 may be affected by these post-translational modifications. To determine the specific domains of TRIM24 required for p53 interaction, we performed GST pull-downs with in vitro translated, Flag-TRIM24 protein constructs and recombinant GST-p53 protein purified from E. coli. We found that the Linker region is sufficient for interaction of p53 and TRIM24. Taken together, these data indicate that the interaction between p53 and TRIM24 does occur in vitro and that interaction may be influenced by post-translational modifications of the proteins.