Cost-effectiveness of alternative powertrains for reduced energy use and CO2 emissions in passenger vehicles

This work analysed the cost-effectiveness of avoiding carbon dioxide (CO2) emissions using advanced internal combustion engines, hybrids, plug-in hybrids, fuel cell vehicles and electric vehicles across the nine UK passenger vehicles segments. Across all vehicle types and powertrain groups, minimum installed motive power was dependent most on the time to accelerate from zero to 96.6km/h (60mph). Hybridising the powertrain reduced the difference in energy use between vehicles with slow (t z - 60 > 8 s) and fast acceleration (t z - 60 < 8 s) times. The cost premium associated with advanced powertrains was dependent most on the powertrain chosen, rather than the performance required. Improving non-powertrain components reduced vehicle road load and allowed total motive capacity to decrease by 17%, energy use by 11%, manufacturing cost premiums by 13% and CO2 emissions abatement costs by 15%. All vehicles with advanced internal combustion engines, most hybrid and plug-in hybrid powertrains reduced net CO2 emissions and had lower lifetime operating costs than the respective segment reference vehicle. Most powertrains using fuel cells and all electric vehicles had positive CO2 emissions abatement costs. However, only vehicles using advanced internal combustion engines and parallel hybrid vehicles may be attractive to consumers by the fuel savings offsetting increases in vehicle cost within two years. This work demonstrates that fuel savings are possible relative to today's fleet, but indicates that the most cost-effective way of reducing fuel consumption and CO2 emissions is by advanced combustion technologies and hybridisation with a parallel topology. © 2014 Elsevier Ltd.

Photodegradation of 2-naphthol in aqueous solutions in the presence of humic acid and ferric ions

In this work, the photodegradation of the carcinogenic pollutant 2-naphthol in aqueous solution containing Aldrich humic acid (HA) and ferric ions (Fe(III)) under 125 W and 250 W high pressure mercury lamp (HPML, lambda >= 365 nm) irradiation was investigated. The photooxidation efficiencies were dependent on the pH values, light intensities and Fe(III)/HA concentration in the water, with higher efficiency at pHs 3-4, and 50 mu mol l(-1) Fe(III) with 20 mg l(-1) HA under 250 W HPML. The initial rate of photooxidation increases with increasing, the initial concentration of 2-naphthol from 10 mu mol l(-1) to 100 mu mol l(-1), while do not change at 50 and 100 mu mol l(-1). However, higher removal efficiency of 2-naphthol is achieved at its lower initial concentration of 10 mu mol l(-1), and initial rate of photooxidation is 0.193 mu mol l(-1) min(-1). Dissolved oxygen (DO) plays an important role in the system containing Fe(III)-HA complexes in which Fenton and photo-Fenton reactions were enhanced in the environment. Hydroxyl radicals produced in HA solution with or without ferric ions were determined by using benzene as free radical scavenger and phenol as scavenging products proportional to hydroxyl radicals. By using UV-Vis and excited fluorescence spectrum techniques, the main photooxidation products, which have higher absorption in the region of 240-340 nm, were found, and the mechanisms for the oxidative degradation is proposed.

Photoreduction of mercuric salt in UV/Fe (III)-oxalate complex system

In this paper, the photochemical reduction process of Hg (II) in aqueous solution containing ferric iron and oxalate (Ox) has been studied. Under the radiation of a low-pressure mercury lamp (lambda = 253.7 nm, 8W), Fe(III)-oxalate complexes undergo photolysis to produce ferrous ions and other organic reductive species, which reduce Hg(II) subsequently. For 0.1 mg/L Hg (II), the photoreduction efficiency is comparatively higher in the solution at pH 5.0 than that over the range of 3.0 similar to 8.0. The photoreduction efficiency of Ho (II) in aqueous solution increases with increasing, initial concentration of ferric ions from 0.02 mmol/L to 0.2 mmol/L and initial concentration of oxalate from 0.96 mmol/L to 4.8 mmol/L and then gradually approaches to a steady state. CH3OH also contributes the reduction of Hg (II). We investigate the increase of the ferric, oxalate and CH3OH concentrations resulting from the increase of reduction efficiency of Hg (II). It can be seen that ferrous ions and other reactive species are reductants of Hg (II), and the reaction product with oxalate is mainly volatile metallic mercury.

Environmental threats to children's health in Southeast Asia and the Western Pacific

The Southeast Asia and Western Pacific regions contain half of the world's children and are among the most rapidly industrializing regions of the globe. Environmental threats to children's health are widespread and are multiplying as nations in the area undergo industrial development and pass through the epidemiologic transition. These environmental hazards range from traditional threats such as bacterial contamination of drinking water and wood smoke in poorly ventilated dwellings to more recently introduced chemical threats such as asbestos construction materials; arsenic in groundwater; methyl isocyanate in Bhopal, India; untreated manufacturing wastes released to landfills; chlorinated hydrocarbon and organophosphorous pesticides; and atmospheric lead emissions from the combustion of leaded gasoline. To address these problems, pediatricians, environmental health scientists, and public health workers throughout Southeast Asia and the Western Pacific have begun to build local and national research and prevention programs in children's environmental health. Successes have been achieved as a result of these efforts: A cost-effective system for producing safe drinking water at the village level has been devised in India; many nations have launched aggressive antismoking campaigns; and Thailand, the Philippines, India, and Pakistan have all begun to reduce their use of lead in gasoline, with resultant declines in children's blood lead levels. The International Conference on Environmental Threats to the Health of Children, held in Bangkok, Thailand, in March 2002, brought together more than 300 representatives from 35 countries and organizations to increase awareness on environmental health hazards affecting children in these regions and throughout the world. The conference, a direct result of the Environmental Threats to the Health of Children meeting held in Manila in April 2000, provided participants with the latest scientific data on children's vulnerability to environmental hazards and models for future policy and public health discussions on ways to improve children's health. The Bangkok Statement, a pledge resulting from the conference proceedings, is an important first step in creating a global alliance committed to developing active and innovative national and international networks to promote and protect children's environmental health.

Enhanced infrared emission from colloidal HgTe nanocrystal quantum dots on silicon-on-insulator photonic crystals

A two dimensional silicon-on-insulator based photonic crystal structure is used to enhance the emission from colloidal HgTe nanocrystal quantum dots embedded in a thin polymer film. The enhancement is resonant to the leaky eigenmodes of the photonic crystals due to coherent scattering effects. Transmittance and photoluminescence experiments are presented to map the leaky mode dispersion and the angle dependence of the emission enhancement factor, which reaches values up to 80 (650) for vertical (oblique) emission in the telecommunication wavelength range.

Electronic structure and electron g factors of HgTe quantum dots

The electronic structure and electron g factors of HgTe quantum dots are investigated, in the framework of the eight-band effective-mass approximation. It is found that the electron states of quantum spheres have aspheric properties due to the interaction between the conduction band and valence band. The highest hole states are S (l = 0) states, when the radius is smaller than 9.4 nm. the same as the lowest electron states. Thus strong luminescence from H-Te quantum dots with radius smaller than 9.4 nm has been observed (Rogach et al 2001 Phys. Statits Solidi b 224 153). The bandgap of H-Te quantum spheres is calculated and compared with earlier experimental results (Harrison et al 2000 Pure Appl. Chem. 72 295). Due to the quantum confinement effect, the bandgap of the small HgTe quantum spheres is positive. The electron g factors of HgTe quantum spheres decrease with increasing radius and are nearly 2 when the radius is very small. The electron g factors of HgTe quantum ellipsoids are also investigated. We found that as some of the three dimensions increase, the electron g factors decrease. The more the dimensions increase, the more the g factors decrease. The dimensions perpendicular to the direction of the magnetic field affect the g factors more than the other dimension.

Hg胁迫对两种基因型小麦生长及其过氧化物酶活性的影响

用不同浓度Hg处理两种基因型小麦种子,较低浓度的Hg对小麦种子萌发影响比较小,对抗旱品种的小麦种子(陕合)的萌发有略微的刺激作用。小剂量、短时间的重金属处理可以提高POD的活性,发芽后受到Hg胁迫的陕合对Hg的耐受性低于发芽前就受到Hg胁迫的陕合,也低于同样胁迫处理的小麦品种(郑引)。发芽后进行Hg胁迫处理情况下,陕合对于Hg胁迫比较敏感,POD活性随着Hg浓度的升高而下降;而郑引,低浓度Hg对其POD活性有促进作用。在小麦发芽前就受到Hg胁迫的情况下,陕合和郑引的POD活性都随着Hg浓度增加表现为先上升而后下降趋势。

运用含有偶氮苯的自组装单层膜在光化学条件下可逆地控制细胞黏附

细胞生物学研究的一个重要方向是动态地控制细胞在基底上的黏附。最近，随着表面化学的研究深入，尤其是对烷基硫醇在金基底上形成自组装单层膜（self-assembled monolayers, SAMs）这一体系的研究，使得人们能在分子水平的表面上控制细胞黏附。精氨酸-甘氨酸-天冬氨酸（arginine-glycine-aspartate, RGD）序列首先是从细胞外基质蛋白中分离出来的，能够识别并非共价结合细胞膜表面的整合素受体，从而促进细胞黏附。以前的一些工作已经证实，将含有RGD的肽链连接到SAMs表面之后，能够生物特异性地黏附动物细胞。已有的手段比如光照、电压、加热、微电极、微流控以及表面纳米形貌的梯度变化，都不能真正实现可逆地控制细胞黏附，原因是这些方法所用的化学有限；这些方法也不能得到完全抗拒细胞黏附的表面，原因是这些方法产生的表面缺陷等不完整。用两种不同波长的光（紫外光和可见光）照射偶氮苯，偶氮苯会发生可逆的光致异构变化，因此，偶氮苯的光致异构性质可以用来可逆地控制细胞在表面黏附。运用含有偶氮苯的混合SAMs，偶氮苯的末端连接GRGDS肽，混合SAMs中是以末端为六聚乙二醇的硫醇为背景，该SAMs修饰而成的表面能够黏附或者抗拒细胞黏附，其表面黏附性质取决于SAMs中偶氮苯的构象。该方法提供了一种在分子水平的表面上我们所了解到的唯一能可逆控制细胞黏附的方法，该方法需要用到的光源来自于标准荧光显微镜所配置的汞灯。 为了实现在金基底表面可逆的控制细胞黏附，我们合成了如下三个化合物： 由于化合物1的溶解性很差，几乎在所有溶剂里都不溶，所以不能直接用化合物1制备SAMs；化合物2能高效地抗拒细胞的黏附；化合物3的偶氮苯末端是活化酯，能够连接GRGDS肽，从而控制细胞黏附。 将化合物2和化合物3以一定的比例均匀混合在金基底表面形成SAMs，然后将GRGDS肽连接到偶氮苯(反式)的末端（通过GRGDS肽的甘氨酸上的伯胺基与偶氮苯末端的活化酯反应），从而得到细胞黏附的表面。用紫外光照射该细胞黏附表面5-10小时，随着偶氮苯的构象由反式变为顺式，偶氮苯末端的GRGDS肽淹没在化合物2的六聚乙二醇中，得到抗拒细胞黏附的惰性表面。再用可见光照射该惰性表面1个小时，随着偶氮苯的构象由顺式变为反式，原先埋没在六聚乙二醇中的GRGDS肽伸展至单层膜的末端，又得到了细胞黏附的表面。因此，该表面能完全可逆地控制细胞在金表面黏附。 An important area in cell biology is the dynamic control of cell adhesion on substrates. Recent advancements in surface chemistry, in particular, self-assembled monolayers (SAMs) of alkanethiols on gold substrates, have permitted unprecedented control of cell adhesion via molecularly defined surfaces. The tri-peptide sequence arginine-glycine-aspartate (RGD), initially isolated from the extracellular matrix (ECM) proteins, can recognize and non-covalently bind with integrin receptors on cell membranes to promote cell adhesion. Some previous work has demonstrated that RGD peptide grafted on SAMs can allow bio-specific adhesion of mammalian cells that mimic natural adhesion. Existing technologies such as light, voltage, heat, microelectrodes, microfluidic systems and surface gradient of nanotopography, either cannot realize fully reversible control of cell adhesion, due to the limitation in the chemistry used, or cannot yield a surface completely resistant against cell adhesion, due to the imperfection of surfaces. Azobenzenes undergo reversible photo-induced isomerization rapidly at two different wavelengths of light (UV and visible light), it therefore potentially allows the reversible control of cell adhesion on a surface. By using a mixed SAMs presenting azobenzene groups terminated in GRGDS peptides in a background of hexa(ethylene glycol) groups, the surface can either accommodate or resist cell adhesion depending on the conformation of the azobenzene embedded in SAMs. This method provides the only means we know to control cell adhesion reversibly on a molecularly well-defined surface by using light generated by a mercury lamp equipped on standard fluorescence microscopes. To realize the reversible control of cell adhesion on gold surface, we synthesized three kinds of compounds as following, We found that it was difficult to obtain SAMs directly from compound 1 because of its poor solubility in almost all kinds of solvents; compound 2 can resist cell adhesion efficiently; compound 3 presents an azobenzene terminated with NHS-activated ester, which can couple with a GRGDS peptide to control cell adhesion. After coating a gold surface with compound 2 and 3 in appropriate ratios to form a SAM followed by coupling the GRGDS peptides with NHS-activated esters at the end of azobenzene (E configuration) resulted in a cell-adhesive SAM. Irradiating this cell-adhesive SAM with UV light for 5-10 h converted the E configuration of azobenzene into the Z form, the GRGDS peptides becoming masked in the PEG, resulting in a cell-resistant surface. These SAM could again support cell adhesion as a result of the conformational switch of azobenzene from Z to E with the irradiation of visible light for 1 h. This surface, therefore, allows completely reversible control of cell adhesion on a gold surface.

Protein A immobilized monolithic capillary column for affinity chromatography

Monolithic capillary columns for affinity chromatography were prepared by an in situ polymerization procedure using glycidyl methacrylate (GMA) as a monomer and trimethylolpropane trimethacrylate (TRIM) and ethylene dimethacrylate (EDMA) as cross-linkers, respectively. Scanning electron microscopy was applied to characterize the morphology of the end of monolithic capillary and mercury intrusion porosimetry to characterize the polymer rod prepared within the confines of a stainless steel column with 50 mm x 4.6 mm i.d. under the same polymerization condition. Obvious differences in the porous properties between the TRIM- and EDMA-based monoliths could be observed. Moreover, the mechanical stability of these two monolithic capillary columns was compared by testing the reproducibility of the column performance. The rod prepared with GMA and TRIM proved to be mechanically more stable than that prepared with GMA and EDMA. Protein A was immobilized on the monolithic rod for affinity chromatography and the experiments were performed on a capillary electrophoresis instrument, using its pressure system as the driving force. Non-specific adsorption was not observed on the TRIM-based affinity column, as proved with bovine serum albumin (BSA) as a test protein. The affinity column prepared with GMA and TRIM was then applied to determine the hIgG concentration in human serum. The correlative coefficient of the calibration curve reached 0.9942. The amount of adsorbed hIgG was unaffected by the flow rate of the loading buffer, which makes this method suitable for fast determination of biomacromolecules in microliter samples. (C) 2002 Elsevier Science B.V All rights reserved.

Automated voltammetric system for shipboard determination of metal speciation in sea water

An automated and semi-intelligent voltammetric system is described for trace metal analysis. The system consists of a voltammeter interfaced with a personal computer, a sample changer, 2 peristaltic pumps, a motor burette and a hanging mercury drop electrode. The system carries out fully automatically approximately 5 metal determinations per hour (including at least 3 repetitive scans and calibration by standard addition) at trace levels encountered in clean sea water. The computer program decides what level of standard addition to use and evaluates the data prior to switching to the next sample. Alternatively, the system can be used to carry out complexing ligand titration with copper whilst recording the labile copper concentration; in this mode up to 8 full titrations are carried out per day. Depth profiles for chromium speciation in the Mediterranean Sea and a profile for copper complexing ligand concentrations in the North Atlantic Ocean measured on board-ship with the system are presented. The chromium speciation was determined using a new method to differentiate between Cr(III) and Cr(VI) utilizing adsorption of Cr(III) on silica particles.

Nontoxic electrodes of solid amalgams

This is a review of electrodes based on nontoxic solid amalgams (MeSAE) (prepared by amalgamation of soft metal powders) in connection with some other kinds of voltammetric electrodes is given. Information is summarized on various types of MeSAEs (esp. AgSAE, CuSAE, AuSAE), pretreatment of their surfaces, their hydrogen overvoltage in aqueous solutions, conditions for their testing, electroanalytical parameters and use, in compared with the hanging mercury drop electrode (HMDE). Although the solid amalgam electrodes do not reach the quality of the HMDE, in many cases they represent its possible alternative. The broad range of voltammetric applications of the MeSAEs, especially of the AgSAEs, their good mechanical stability, simple handling, and new aspects of their use in electrochemical techniques are documented by numerous examples.

Stripping voltammetric determination of Pb(II) and Cd(II) based on the multiwalled carbon nanotubes-Nafion-bismuth modified glassy carbon electrodes

In this work, a new method for the simultaneous determination of Pb(II) and Cd(II) on the multiwalled carbon nanotubes (MWNT)-Nafion-bismuth modified glassy carbon electrode (GCE) using square-wave anodic stripping voltammetry has been studied. Scanning electron microscopy was used to investigate the characteristics of the MWNT-Nafion-bismuth modified GCE.

Bluish-white emission from radical carbonyl impurities in amorphous Al2O3 prepared via the Pechini-type sol-gel process

Many efforts have been devoted to exploring novel luminescent materials that do not contain expensive or toxic elements, or do not need mercury vapor plasma as the excitation source. In this paper, amorphous Al2O3 powder samples were prepared via the Pechini-type sol-gel process. The resulting samples were characterized by X-ray diffraction (XRD), Fourier transform infrared (FT-IR) spectroscopy, field emission scanning electron microscopy (FESEM), photoluminescence (PL) excitation and emission spectra, kinetic decay, and electron paramagnetic resonance (EPR).