Collective Organization of Complex Networks: Emergent Scales, Vulnerability, and Targeting of Desired Dynamics

Cuando una colectividad de sistemas dinámicos acoplados mediante una estructura irregular de interacciones evoluciona, se observan dinámicas de gran complejidad y fenómenos emergentes imposibles de predecir a partir de las propiedades de los sistemas individuales. El objetivo principal de esta tesis es precisamente avanzar en nuestra comprensión de la relación existente entre la topología de interacciones y las dinámicas colectivas que una red compleja es capaz de mantener. Siendo este un tema amplio que se puede abordar desde distintos puntos de vista, en esta tesis se han estudiado tres problemas importantes dentro del mismo que están relacionados entre sí. Por un lado, en numerosos sistemas naturales y artificiales que se pueden describir mediante una red compleja la topología no es estática, sino que depende de la dinámica que se desarrolla en la red: un ejemplo son las redes de neuronas del cerebro. En estas redes adaptativas la propia topología emerge como consecuencia de una autoorganización del sistema. Para conocer mejor cómo pueden emerger espontáneamente las propiedades comúnmente observadas en redes reales, hemos estudiado el comportamiento de sistemas que evolucionan según reglas adaptativas locales con base empírica. Nuestros resultados numéricos y analíticos muestran que la autoorganización del sistema da lugar a dos de las propiedades más universales de las redes complejas: a escala mesoscópica, la aparición de una estructura de comunidades, y, a escala macroscópica, la existencia de una ley de potencias en la distribución de las interacciones en la red. El hecho de que estas propiedades aparecen en dos modelos con leyes de evolución cuantitativamente distintas que siguen unos mismos principios adaptativos sugiere que estamos ante un fenómeno que puede ser muy general, y estar en el origen de estas propiedades en sistemas reales. En segundo lugar, proponemos una medida que permite clasificar los elementos de una red compleja en función de su relevancia para el mantenimiento de dinámicas colectivas. En concreto, estudiamos la vulnerabilidad de los distintos elementos de una red frente a perturbaciones o grandes fluctuaciones, entendida como una medida del impacto que estos acontecimientos externos tienen en la interrupción de una dinámica colectiva. Los resultados que se obtienen indican que la vulnerabilidad dinámica es sobre todo dependiente de propiedades locales, por tanto nuestras conclusiones abarcan diferentes topologías, y muestran la existencia de una dependencia no trivial entre la vulnerabilidad y la conectividad de los elementos de una red. Finalmente, proponemos una estrategia de imposición de una dinámica objetivo genérica en una red dada e investigamos su validez en redes con diversas topologías que mantienen regímenes dinámicos turbulentos. Se obtiene como resultado que las redes heterogéneas (y la amplia mayora de las redes reales estudiadas lo son) son las más adecuadas para nuestra estrategia de targeting de dinámicas deseadas, siendo la estrategia muy efectiva incluso en caso de disponer de un conocimiento muy imperfecto de la topología de la red. Aparte de la relevancia teórica para la comprensión de fenómenos colectivos en sistemas complejos, los métodos y resultados propuestos podrán dar lugar a aplicaciones en sistemas experimentales y tecnológicos, como por ejemplo los sistemas neuronales in vitro, el sistema nervioso central (en el estudio de actividades síncronas de carácter patológico), las redes eléctricas o los sistemas de comunicaciones. ABSTRACT The time evolution of an ensemble of dynamical systems coupled through an irregular interaction scheme gives rise to dynamics of great of complexity and emergent phenomena that cannot be predicted from the properties of the individual systems. The main objective of this thesis is precisely to increase our understanding of the interplay between the interaction topology and the collective dynamics that a complex network can support. This is a very broad subject, so in this thesis we will limit ourselves to the study of three relevant problems that have strong connections among them. First, it is a well-known fact that in many natural and manmade systems that can be represented as complex networks the topology is not static; rather, it depends on the dynamics taking place on the network (as it happens, for instance, in the neuronal networks in the brain). In these adaptive networks the topology itself emerges from the self-organization in the system. To better understand how the properties that are commonly observed in real networks spontaneously emerge, we have studied the behavior of systems that evolve according to local adaptive rules that are empirically motivated. Our numerical and analytical results show that self-organization brings about two of the most universally found properties in complex networks: at the mesoscopic scale, the appearance of a community structure, and, at the macroscopic scale, the existence of a power law in the weight distribution of the network interactions. The fact that these properties show up in two models with quantitatively different mechanisms that follow the same general adaptive principles suggests that our results may be generalized to other systems as well, and they may be behind the origin of these properties in some real systems. We also propose a new measure that provides a ranking of the elements in a network in terms of their relevance for the maintenance of collective dynamics. Specifically, we study the vulnerability of the elements under perturbations or large fluctuations, interpreted as a measure of the impact these external events have on the disruption of collective motion. Our results suggest that the dynamic vulnerability measure depends largely on local properties (our conclusions thus being valid for different topologies) and they show a non-trivial dependence of the vulnerability on the connectivity of the network elements. Finally, we propose a strategy for the imposition of generic goal dynamics on a given network, and we explore its performance in networks with different topologies that support turbulent dynamical regimes. It turns out that heterogeneous networks (and most real networks that have been studied belong in this category) are the most suitable for our strategy for the targeting of desired dynamics, the strategy being very effective even when the knowledge on the network topology is far from accurate. Aside from their theoretical relevance for the understanding of collective phenomena in complex systems, the methods and results here discussed might lead to applications in experimental and technological systems, such as in vitro neuronal systems, the central nervous system (where pathological synchronous activity sometimes occurs), communication systems or power grids.

Policy processes and collective action in water reforms: the cases of Nicaragua and Suriname

Las reformas de agua en países en desarrollo suelen llevarse a cabo junto con cambios institucionales más profundos o, incluso, acompañadas de cambios constitucionales o de régimen político. Por lo tanto, los marcos institucionales adaptados a países gobernados sujetos al estado de derecho pueden no ser apropiados para contextos gobernados fundamentalmente, al menos en sus inicios, por instituciones informales o poco maduras. Esta tesis toma las reformas de agua como punto de partida y pretende contribuir a la literatura mediante una serie de análisis empíricos tanto del ámbito general como del plano individual o sujeto personal de la política del agua. En el ámbito general, el foco se pone en los factores que explican el fallo de la acción colectiva en dos contextos diferentes: 1) en la implementación de la nueva Ley de Aguas de Nicaragua y 2) en el mantenimiento y revitalización de las instituciones de riego en Surinam. En el plano del individuo, la investigación se centra en las decisiones de los usuarios de los recursos y analiza el papel crítico de las variables sociales para la gestión de los recursos comunes. Para ello, el método de investigación utilizado es mixto, combinando el análisis de entrevistas, encuestas y experimentos. En el ámbito general, los resultados muestran que las principales barreras para la implementación de la nueva Ley de Aguas de Nicaragua podrían tener su reflejo en el lenguaje de la Ley y, por tanto, en la forma en la que se definen y configuran las instituciones incluidas en dicha Ley. Así, la investigación demuestra que la implementación de políticas no puede ser estudiada o entendida sin tener en cuenta tanto el diseño de la propia política como el marco socio-ecológico en el que se enmarca. El contexto específico de Nicaragua remarca la importancia de considerar tanto las instituciones formales como informales en los procesos de transición política. A pesar de que las reformas de agua requieren plazos largos para su implementación, el hecho de que exista una diferencia entre las reglas tal cual se definen formalmente y las reglas que operan en la realidad merece una mayor consideración en el diseño de políticas basadas fundamentalmente en instituciones formales. En el ámbito de la conducta individual, el análisis de la acción colectiva ofrece una serie de observaciones empíricas interesantes. En el caso de Nicaragua, los resultados indican que la intensidad de las relaciones sociales, el tipo de agentes dispuestos a proporcionar apoyo social y el nivel de confianza en la comunidad son factores que explican de manera significativa la participación en la comunidad. Sin embargo, el hecho de que la gestión colectiva de riego se produzca, en la mayoría de casos, en torno a lazos familiares sugiere que las variables de capital social críticas se definen en gran medida en la esfera familiar, siendo difícil que se extiendan fuera de estos nexos. El análisis experimental de los resultados de un juego de uso de recurso común y contribución al bien público muestra que las preferencias pro-sociales de los individuos y la heterogeneidad del grupo en términos de composición por sexo son factores que explican significativamente los resultados y las decisiones de apropiación a lo largo del juego. En términos del diseño de las políticas, es fundamental tener en cuenta las dinámicas de participación y uso de los recursos comunes de manera que los niveles de cooperación puedan mantenerse en el largo plazo, lo cual, como se observa en el caso de Surinam, no es siempre posible. Finalmente, el caso de Surinam es un ejemplo ilustrativo de los procesos de acción colectiva en economías en transición. El análisis del fallo de la acción colectiva en Surinam muestra que los procesos políticos vinculados al período colonial y de independencia explican en gran medida la falta de claridad en las reglas operacionales y colectivas que gobiernan la gestión de los sistemas de riego y drenaje. Los resultados empíricos sugieren que a pesar de que la acción colectiva para la provisión de los servicios de riego y drenaje estaba bien establecida bajo el régimen colonial, la auto-organización no prosperó en un contexto dependiente del apoyo externo y regido fundamentalmente por reglas diseñadas al nivel competencial del gobierno central. El sistema socio-ecológico que se desarrolló durante la transición post-colonial favoreció, así, la emergencia de comportamientos oportunistas, y posteriormente la inoperancia de los Water Boards (WBs) creados en la época colonial. En este sentido, cualquier intento por revitalizar los WBs y fomentar el desarrollo de la auto-organización de los usuarios necesitará abordar los problemas relacionados con los patrones demográficos, incluyendo la distribución de la tierra, el diseño de instituciones y la falta de confianza en el gobierno, además de las inversiones típicas en infraestructura y sistemas de información hidrológicos. El liderazgo del gobierno, aportando empuje de arriba-abajo, es, además, otro elemento imprescindible en Surinam. ABSTRACT Water reforms in developing countries take place along deeper institutional and even constitutional. Therefore, institutional frameworks that might result in positive outcomes in countries governed by the rule of law might not fit in contexts governed mainly by informal or immature institutions. This thesis takes water reforms as the starting point and aims to contribute to the literature by presenting several conceptual and empirical analyses at both general and individual levels. At the general national level, the focus is on the factors explaining failure of collective action in two different settings: 1) in the implementation of the new Nicaraguan Water Law and 2) in sustaining and revitalizing irrigation institutions in Suriname. At the individual level, the research focuses on the actions of resource users and analyzes the critical role of social variables for common pool resources management. For this purpose, the research presented in this thesis makes use of a mixed-method approach, combining interviews, surveys and experimental methods. Overall, the results show that major barriers for the implementation of the new Nicaraguan Water Law have its reflection on the language of the Law and, therefore, on the way institutions are defined and configured. In this sense, our study shows that implementation cannot fruitfully be studied and understood without taking into account both the policy design and the social-ecological context in which it is framed. The specific setting of Nicaragua highlights the relevance of considering both formal and informal institutions when promoting policy transitions. Despite the unquestionable fact that water reforms implementation needs long periods of time, there is still a gap between the rules on paper and the rules on the ground that deserves further attention when proposing policy changes on the basis of formal institutions. At the level of the individual agent, the analysis of collective action provides a number of interesting empirical insights. In the case of Nicaragua, I found that the intensity of social networks, the type of agents willing to provide social support and the level of trust in the community are all significant factors in explaining collective action at community level. However, the fact that most collective irrigation relies on family ties suggests that critical social capital variables might be defined within the family sphere and making it difficult to go beyond it. Experimental research combining a common pool resource and a public good game in Nicaragua shows that individuals’ pro-social traits and group heterogeneity in terms of sex composition are significant variables in explaining efficiency outcomes and effort decisions along the game. Thus, with regard to policy design, it is fundamental to consider carefully the dynamics of agents' participation and use of common pool resources, for sustaining cooperation in the long term, which, as seen in the case and Surinam, is not always possible. The case of Suriname provides a rich setting for the analysis of collective action in transition economies. The analysis of decay of collective irrigation in Suriname shows that the lack of clear operational and collective choice rules appear to be rooted in deeper political processes that date back to the colonial period. The empirical findings suggest that despite collective action for the provision of irrigation and drainage services was well established during the colonial period, self-organization did not flourish in a context governed by colonial state-crafted rules and mostly dependent on external support. The social-ecological system developed during the post-colonial transition process favored the emergence of opportunistic behavior. In this respect, any attempt to revitalize WBs and support self-organization will need to tackle the problems derived from demographic patterns, including land allocation, institutions design and government distrust, in addition to the typical investments in both physical infrastructure and hydrological information systems. The leadership role of the government, acting as a top-down trigger, is another essential element in Suriname.

Dynamics in the governance of collective irrigation systems: Evidence from field experiments in Nicaragua.

The objective of this study is to analyze the common pool resource appropriation and public good provisiondecisions in a dynamic setting, testing the differences in behavior and performance between lab and field subjects. We performeda total of 45 games in Nicaragua, including 88 villagers in rural communities and 92 undergraduate students. In order to analyze sequential decision making, we introduce a dynamic and asymmetric irrigation game that combines the typical social dilemmas associated to irrigation systems management.In addition, in 9 out of 22 villagers’ groups, we implemented a treatment that included the disclosure of subjects’ appropriation of the common pool resource. The results reveal that the provision of individuals’ appropriation level results in higher appropriation in subsequent rounds. In addition, the results show that non-treated villagers provide more public good than treated villagers but if compared with students the differences are not significant. The results also suggest that appropriation levels are below the Nash prediction of full appropriation, but above the social efficient level. This results in an efficiency loss in the game that can be explained to a large extent by individual decisions on appropriation and public good contribution and by group appropriation behavior.

Análisis mediante cálculo numérico (CFD) del comportamiento de anemómetros de cazoletas = CFD analysis of cup anemometers performance

El presente trabajo consiste en la simulación del flujo aerodinámico alrededor de cazoletas de anemómetros. Para ello se ha utilizado un código numérico o software comercial de análisis numérico de fluidos o CFD (Computational Fluid Dynamics). Este trabajo es un aporte más en la línea de investigación acerca del comportamiento de los anemómetros de cazoletas, que viene llevándose a cabo en el Instituto Universitario de Microgravedad “Ignacio Da Riva” (IDR/UPM). La primera parte de este proyecto consistió en la realización de simulaciones de tipo estacionarias (esto es, con la cazoleta bajo un cierto ángulo de incidencia con respecto al viento pero sin movimiento de rotación). De esta forma se analiza de forma independiente y asilada la cazoleta en cada una de las diferentes posiciones a lo largo de un giro de 360 grados. Así pues, a varios modelos de cazoleta se les fue variando su posición en incrementos de 10 grados desde de la posición angular inicial q = 0º hasta q = 180º, ya que las cazoletas presentan un comportamiento simétrico. La segunda parte de este proyecto se destinó a la realización de otra serie de simulaciones de tipo no estacionarias. Este tipo de simulaciones se realizaron concretamente a sólo un modelo de cazoleta (cónica no porosa). Estas últimas simulaciones, en concreto nueve, se realizaron variando la velocidad angular de la cazoleta respecto a la velocidad del viento.

Performance-based seismic design of a retaining wall

The design of containment walls suffering seismic loads traditionally has been realized with methods based on pseudoanalitic procedures such as Mononobe-Okabe's method, which it has led in certain occasions to insecure designs, that they have produced the ruin of many containment walls suffering the action of an earthquake. The recommendations gathered in Mononobe-Okabe's theory have been included in numerous Codes of Seismic Design. It is clear that a revision of these recommendations must be done. At present there is taking place an important review of the design methods of anti-seismic structures such as containment walls placed in an area of numerous earthquakes, by means of the introduction at the beginning of the decade of 1990 the Displacement Response Spectrum (DRS) and the Capacity Demand Diagram (CDD) that suppose an important change in the way of presenting the Elastic Response Spectrum (ERS). On the other hand in case of action of an earthquake, the dynamic characteristics of a soil have been referred traditionally to the speed of the shear waves that can be generated in a site, together with the characteristics of plasticity and damping of the soil. The Principle of the energy conservation explains why a shear upward propagating seismic wave can be amplified when travelling from a medium with high shear wave velocity (rock) to other medium with lower velocity (soil deposit), as it happened in the earthquake of Mexico of 1985. This amplification is a function of the speed gradient or of the contrast of impedances in the border of both types of mediums. A method is proposed in this paper for the design of containment walls in different soils, suffering to the action of an earthquake, based on the Performance-Based Seismic Design.

Teamwork, motivational profiles and academic performance in computer science engineering

The present work is aimed at discussing several issues related to the teamwork generic competence, motivational profiles and academic performance. In particular, we study the improvement of teamwork attitude, the predominant types of motivation in different contexts and some correlations among these three components of the learning process. The above-mentioned aspects are of great importance. Currently, the professional profile of engineers has a strong teamwork component and the motivational profile of students determines both their tendencies when they come to work as part of a team, as well as their performance at work. Taking these issues into consideration, we suggest four hypotheses: (H1) students improve their teamwork capacity through specific training and carrying out of a set of activities integrated into an active learning process; (H2) students with higher mastery motivation have a better attitude towards teamwork; (H3) students with different types of motivations reach different levels of academic performance; and (H4) students show different motivation profiles in different circumstances: type of courses, teaching methodologies, different times of the learning process. This study was carried out with Computer Science Engineering students from two Spanish universities. The first results point to an improvement in teamwork competence of students if they have previously received specific training in facets of that competence. Other results indicate that there is a correlation between the motivational profiles of students and their perception of teamwork competence. Finally, results point to a clear relationship between some kind of motivation and academic performance. In particular, four kinds of motivation are analyzed and students are classified into two groups according to them. After analyzing several marks obtained in compulsory courses, we perceive that those students that show higher motivation for avoiding failure obtain, in general, worse academic performance.

Shake-table tests of a reinforced concrete frame designed following modern codes: seismic performance and damage evaluation

This paper presents shake-table tests conducted on a two-fifths-scale reinforced concrete frame representing a conventional construction design under current building code provisions in the Mediterranean area. The structure was subjected to a sequence of dynamic tests including free vibrations and four seismic simulations in which a historical ground motion record was scaled to levels of increasing intensity until collapse. Each seismic simulation was associated with a different level of seismic hazard, representing very frequent, frequent, rare and very rare earthquakes. The structure remained basically undamaged and within the inter-story drift limits of the "immediate occupancy" performance level for the very frequent and frequent earthquakes. For the rare earthquake, the specimen sustained significant damage with chord rotations of up to 28% of its ultimate capacity and approached the upper bound limit of inter-story drift associated with "life safety". The specimen collapsed at the beginning of the "very rare" seismic simulation. Besides summarizing the experimental program, this paper evaluates the damage quantitatively at the global and local levels in terms of chord rotation and other damage indexes, together with the energy dissipation demands for each level of seismic hazard. Further, the ratios of column-to-beam moment capacity recommended by Eurocode 8 and ACI-318 to guarantee the formation of a strong column-weak beam mechanism are examined.

Seismic performance and damage evaluation of a reinforced concrete frame with hysteretic dampers through shake-table tests

Passive energy dissipation devices are increasingly implemented in frame structures to improve their performance under seismic loading. Most guidelines for designing this type of system retain the requirements applicable to frames without dampers, and this hinders taking full advantage of the benefits of implementing dampers. Further, assessing the extent of damage suffered by the frame and by the dampers for different levels of seismic hazard is of paramount importance in the framework of performance-based design. This paper presents an experimental investigation whose objectives are to provide empirical data on the response of reinforced concrete (RC) frames equipped with hysteretic dampers (dynamic response and damage) and to evaluate the need for the frame to form a strong column-weak beam mechanism and dissipate large amounts of plastic strain energy. To this end, shake-table tests were conducted on a 2/5-scale RC frame with hysteretic dampers. The frame was designed only for gravitational loads. The dampers provided lateral strength and stiffness, respectively, three and 12 times greater than those of the frame. The test structure was subjected to a sequence of seismic simulations that represented different levels of seismic hazard. The RC frame showed a performance level of "immediate occupancy", with maximum rotation demands below 20% of the ultimate capacity. The dampers dissipated most of the energy input by the earthquake. It is shown that combining hysteretic dampers with flexible reinforced concrete frames leads to structures with improved seismic performance and that requirements of conventional RC frames (without dampers) can be relieved.

Magnetic Attitude Control System for a Small Satellite. Impact on the Thermal Performance

El principal objetivo de la tesis es estudiar el acoplamiento entre los subsistemas de control de actitud y de control térmico de un pequeño satélite, con el fin de buscar la solución a los problemas relacionados con la determinación de los parámetros de diseño. Se considera la evolución de la actitud y de las temperaturas del satélite bajo la influencia de dos estrategias de orientación diferentes: 1) estabilización magnética pasiva de la orientación (PMAS, passive magnetic attitude stabilization), y 2) control de actitud magnético activo (AMAC, active magnetic attitude control). En primer lugar se presenta el modelo matemático del problema, que incluye la dinámica rotacional y el modelo térmico. En el problema térmico se considera un satélite cúbico modelizado por medio de siete nodos (seis externos y uno interno) aplicando la ecuación del balance térmico. Una vez establecido el modelo matemático del problema, se estudia la evolución que corresponde a las dos estrategias mencionadas. La estrategia PMAS se ha seleccionado por su simplicidad, fiabilidad, bajo coste, ahorrando consumo de potencia, masa coste y complejidad, comparado con otras estrategias. Se ha considerado otra estrategia de control que consigue que el satélite gire a una velocidad requerida alrededor de un eje deseado de giro, pudiendo controlar su dirección en un sistema inercial de referencia, ya que frecuentemente el subsistema térmico establece requisitos de giro alrededor de un eje del satélite orientado en una dirección perpendicular a la radiación solar incidente. En relación con el problema térmico, para estudiar la influencia de la velocidad de giro en la evolución de las temperaturas en diversos puntos del satélite, se ha empleado un modelo térmico linealizado, obtenido a partir de la formulación no lineal aplicando un método de perturbaciones. El resultado del estudio muestra que el tiempo de estabilización de la temperatura y la influencia de las cargas periódicas externas disminuye cuando aumenta la velocidad de giro. Los cambios de temperatura se reducen hasta ser muy pequeños para velocidades de rotación altas. En relación con la estrategia PMAC se ha observado que a pesar de su uso extendido entre los micro y nano satélites todavía presenta problemas que resolver. Estos problemas están relacionados con el dimensionamiento de los parámetros del sistema y la predicción del funcionamiento en órbita. Los problemas aparecen debido a la dificultad en la determinación de las características magnéticas de los cuerpos ferromagnéticos (varillas de histéresis) que se utilizan como amortiguadores de oscilaciones en los satélites. Para estudiar este problema se presenta un modelo analítico que permite estimar la eficiencia del amortiguamiento, y que se ha aplicado al estudio del comportamiento en vuelo de varios satélites, y que se ha empleado para comparar los resultados del modelo con los obtenidos en vuelo, observándose que el modelo permite explicar satisfactoriamente el comportamiento registrado. ABSTRACT The main objective of this thesis is to study the coupling between the attitude control and thermal control subsystems of a small satellite, and address the solution to some existing issues concerning the determination of their parameters. Through the thesis the attitude and temperature evolution of the satellite is studied under the influence of two independent attitude stabilization and control strategies: (1) passive magnetic attitude stabilization (PMAS), and (2) active magnetic attitude control (AMAC). In this regard the mathematical model of the problem is explained and presented. The mathematical model includes both the rotational dynamics and the thermal model. The thermal model is derived for a cubic satellite by solving the heat balance equation for 6 external and 1 internal nodes. Once established the mathematical model of the problem, the above mentioned attitude strategies were applied to the system and the temperature evolution of the 7 nodes of the satellite was studied. The PMAS technique has been selected to be studied due to its prevalent use, simplicity, reliability, and cost, as this strategy significantly saves the overall power, weight, cost, and reduces the complexity of the system compared to other attitude control strategies. In addition to that, another control law that provides the satellite with a desired spin rate along a desired axis of the satellite, whose direction can be controlled with respect to the inertial reference frame is considered, as the thermal subsystem of a satellite usually demands a spin requirement around an axis of the satellite which is positioned perpendicular to the direction of the coming solar radiation. Concerning the thermal problem, to study the influence of spin rate on temperature evolution of the satellite a linear approach of the thermal model is used, which is based on perturbation theory applied to the nonlinear differential equations of the thermal model of a spacecraft moving in a closed orbit. The results of this study showed that the temperature stabilization time and the periodic influence of the external thermal loads decreases by increasing the spin rate. However, the changes become insignificant for higher values of spin rate. Concerning the PMAS strategy, it was observed that in spite of its extended application to micro and nano satellites, still there are some issues to be solved regarding this strategy. These issues are related to the sizing of its system parameters and predicting the in-orbit performance. The problems were found to be rooted in the difficulties that exist in determining the magnetic characteristics of the ferromagnetic bodies (hysteresis rods) that are applied as damping devices on-board satellites. To address these issues an analytic model for estimating their damping efficiency is proposed and applied to several existing satellites in order to compare the results with their respective in-flight data. This model can explain the behavior showed by these satellites.

Co-simulation Methodologies for Hybrid and Electric Vehicle Dynamics

In recent decades, full electric and hybrid electric vehicles have emerged as an alternative to conventional cars due to a range of factors, including environmental and economic aspects. These vehicles are the result of considerable efforts to seek ways of reducing the use of fossil fuel for vehicle propulsion. Sophisticated technologies such as hybrid and electric powertrains require careful study and optimization. Mathematical models play a key role at this point. Currently, many advanced mathematical analysis tools, as well as computer applications have been built for vehicle simulation purposes. Given the great interest of hybrid and electric powertrains, along with the increasing importance of reliable computer-based models, the author decided to integrate both aspects in the research purpose of this work. Furthermore, this is one of the first final degree projects held at the ETSII (Higher Technical School of Industrial Engineers) that covers the study of hybrid and electric propulsion systems. The present project is based on MBS3D 2.0, a specialized software for the dynamic simulation of multibody systems developed at the UPM Institute of Automobile Research (INSIA). Automobiles are a clear example of complex multibody systems, which are present in nearly every field of engineering. The work presented here benefits from the availability of MBS3D software. This program has proven to be a very efficient tool, with a highly developed underlying mathematical formulation. On this basis, the focus of this project is the extension of MBS3D features in order to be able to perform dynamic simulations of hybrid and electric vehicle models. This requires the joint simulation of the mechanical model of the vehicle, together with the model of the hybrid or electric powertrain. These sub-models belong to completely different physical domains. In fact the powertrain consists of energy storage systems, electrical machines and power electronics, connected to purely mechanical components (wheels, suspension, transmission, clutch…). The challenge today is to create a global vehicle model that is valid for computer simulation. Therefore, the main goal of this project is to apply co-simulation methodologies to a comprehensive model of an electric vehicle, where sub-models from different areas of engineering are coupled. The created electric vehicle (EV) model consists of a separately excited DC electric motor, a Li-ion battery pack, a DC/DC chopper converter and a multibody vehicle model. Co-simulation techniques allow car designers to simulate complex vehicle architectures and behaviors, which are usually difficult to implement in a real environment due to safety and/or economic reasons. In addition, multi-domain computational models help to detect the effects of different driving patterns and parameters and improve the models in a fast and effective way. Automotive designers can greatly benefit from a multidisciplinary approach of new hybrid and electric vehicles. In this case, the global electric vehicle model includes an electrical subsystem and a mechanical subsystem. The electrical subsystem consists of three basic components: electric motor, battery pack and power converter. A modular representation is used for building the dynamic model of the vehicle drivetrain. This means that every component of the drivetrain (submodule) is modeled separately and has its own general dynamic model, with clearly defined inputs and outputs. Then, all the particular submodules are assembled according to the drivetrain configuration and, in this way, the power flow across the components is completely determined. Dynamic models of electrical components are often based on equivalent circuits, where Kirchhoff’s voltage and current laws are applied to draw the algebraic and differential equations. Here, Randles circuit is used for dynamic modeling of the battery and the electric motor is modeled through the analysis of the equivalent circuit of a separately excited DC motor, where the power converter is included. The mechanical subsystem is defined by MBS3D equations. These equations consider the position, velocity and acceleration of all the bodies comprising the vehicle multibody system. MBS3D 2.0 is entirely written in MATLAB and the structure of the program has been thoroughly studied and understood by the author. MBS3D software is adapted according to the requirements of the applied co-simulation method. Some of the core functions are modified, such as integrator and graphics, and several auxiliary functions are added in order to compute the mathematical model of the electrical components. By coupling and co-simulating both subsystems, it is possible to evaluate the dynamic interaction among all the components of the drivetrain. ‘Tight-coupling’ method is used to cosimulate the sub-models. This approach integrates all subsystems simultaneously and the results of the integration are exchanged by function-call. This means that the integration is done jointly for the mechanical and the electrical subsystem, under a single integrator and then, the speed of integration is determined by the slower subsystem. Simulations are then used to show the performance of the developed EV model. However, this project focuses more on the validation of the computational and mathematical tool for electric and hybrid vehicle simulation. For this purpose, a detailed study and comparison of different integrators within the MATLAB environment is done. Consequently, the main efforts are directed towards the implementation of co-simulation techniques in MBS3D software. In this regard, it is not intended to create an extremely precise EV model in terms of real vehicle performance, although an acceptable level of accuracy is achieved. The gap between the EV model and the real system is filled, in a way, by introducing the gas and brake pedals input, which reflects the actual driver behavior. This input is included directly in the differential equations of the model, and determines the amount of current provided to the electric motor. For a separately excited DC motor, the rotor current is proportional to the traction torque delivered to the car wheels. Therefore, as it occurs in the case of real vehicle models, the propulsion torque in the mathematical model is controlled through acceleration and brake pedal commands. The designed transmission system also includes a reduction gear that adapts the torque coming for the motor drive and transfers it. The main contribution of this project is, therefore, the implementation of a new calculation path for the wheel torques, based on performance characteristics and outputs of the electric powertrain model. Originally, the wheel traction and braking torques were input to MBS3D through a vector directly computed by the user in a MATLAB script. Now, they are calculated as a function of the motor current which, in turn, depends on the current provided by the battery pack across the DC/DC chopper converter. The motor and battery currents and voltages are the solutions of the electrical ODE (Ordinary Differential Equation) system coupled to the multibody system. Simultaneously, the outputs of MBS3D model are the position, velocity and acceleration of the vehicle at all times. The motor shaft speed is computed from the output vehicle speed considering the wheel radius, the gear reduction ratio and the transmission efficiency. This motor shaft speed, somehow available from MBS3D model, is then introduced in the differential equations corresponding to the electrical subsystem. In this way, MBS3D and the electrical powertrain model are interconnected and both subsystems exchange values resulting as expected with tight-coupling approach.When programming mathematical models of complex systems, code optimization is a key step in the process. A way to improve the overall performance of the integration, making use of C/C++ as an alternative programming language, is described and implemented. Although this entails a higher computational burden, it leads to important advantages regarding cosimulation speed and stability. In order to do this, it is necessary to integrate MATLAB with another integrated development environment (IDE), where C/C++ code can be generated and executed. In this project, C/C++ files are programmed in Microsoft Visual Studio and the interface between both IDEs is created by building C/C++ MEX file functions. These programs contain functions or subroutines that can be dynamically linked and executed from MATLAB. This process achieves reductions in simulation time up to two orders of magnitude. The tests performed with different integrators, also reveal the stiff character of the differential equations corresponding to the electrical subsystem, and allow the improvement of the cosimulation process. When varying the parameters of the integration and/or the initial conditions of the problem, the solutions of the system of equations show better dynamic response and stability, depending on the integrator used. Several integrators, with variable and non-variable step-size, and for stiff and non-stiff problems are applied to the coupled ODE system. Then, the results are analyzed, compared and discussed. From all the above, the project can be divided into four main parts: 1. Creation of the equation-based electric vehicle model; 2. Programming, simulation and adjustment of the electric vehicle model; 3. Application of co-simulation methodologies to MBS3D and the electric powertrain subsystem; and 4. Code optimization and study of different integrators. Additionally, in order to deeply understand the context of the project, the first chapters include an introduction to basic vehicle dynamics, current classification of hybrid and electric vehicles and an explanation of the involved technologies such as brake energy regeneration, electric and non-electric propulsion systems for EVs and HEVs (hybrid electric vehicles) and their control strategies. Later, the problem of dynamic modeling of hybrid and electric vehicles is discussed. The integrated development environment and the simulation tool are also briefly described. The core chapters include an explanation of the major co-simulation methodologies and how they have been programmed and applied to the electric powertrain model together with the multibody system dynamic model. Finally, the last chapters summarize the main results and conclusions of the project and propose further research topics. In conclusion, co-simulation methodologies are applicable within the integrated development environments MATLAB and Visual Studio, and the simulation tool MBS3D 2.0, where equation-based models of multidisciplinary subsystems, consisting of mechanical and electrical components, are coupled and integrated in a very efficient way.

Active materiality : the agency of matter from the phenomenological perspective = Materialidad activa : la operatividad de la materia desde el punto de vista fenomenológico

The role of matter has remained central to the making and the thinking of architecture, yet many attempts to capture its essence have been trapped in a dialectic tension between form and materiality, between material consistency and immaterial modes of perception, between static states and dynamic processes, between the real and the virtual, thus advancing an increasing awareness of the perplexing complexity of the material world. Within that complexity, the notion of agency – emerging from and within ecological, politico-economic and socio-cultural processes – calls for a reconceptualization of matter, and consequently processes of materialisation, offering a new understanding of context and space, approached as a field of dynamic relationships. In this context, cutting across boundaries between architectural discourse and practice as well as across the vast trans-disciplinary territory, this dissertation aims to illustrate a variety of design methodologies that have derived from the relational approach. More specifically, the intention is to offer new insights into spatial epistemologies embedded within the notion of atmosphere – commonly associated with the so-called New Phenomenology – and to reflect upon its implications for architectural production. In what follows, the intended argumentation has a twofold dimension. First, through a scrutiny of the notion of atmosphere, the aim is to explore ways of thinking and shaping reality through relations, thus acknowledging the aforementioned complexity of the material universe disclosed through human and non-human as well as material and immaterial forces. Secondly, despite the fact that concerns for atmospherics have flourished over the last few decades, the objective is to reveal that the conceptual foundations and procedures for the production of atmosphere might be found beneath the surface of contemporary debates. Hence, in order to unfold and illustrate previously advocated assumptions, an archaeological approach is adopted, tracing a particular projective genealogy, one that builds upon an atmospheric awareness. Accordingly, in tracing such an atmospheric awareness the study explores the notoriously ambiguous nature and the twofold dimension of atmosphere – meteorological and aesthetic – and the heterogeneity of meanings embedded in them. In this context, the notion of atmosphere is presented as parallactic. It transgresses the formal and material boundaries of bodies. It calls for a reevaluation of perceptual experience, opening a new gap that exposes the orthodox space-bodyenvironment relationships to questioning. It offers to architecture an expanded domain in which to manifest itself, defining architectural space as a contingent construction and field of engagement, and presenting matter as a locus of production/performance/action. Consequently, it is such an expanded or relational dimension that constitutes the foundation of what in the context of this study is to be referred to as affective tectonics. Namely, a tectonics that represents processual and experiential multiplicity of convergent time and space, body and environment, the material and the immaterial; a tectonics in which matter neither appears as an inert and passive substance, nor is limited to the traditionally regarded tectonic significance or expressive values, but is presented as an active element charged with inherent potential and vitality. By defining such a relational materialism, the intention is to expand the spectrum of material attributes revealing the intrinsic relationships between the physical properties of materials and their performative, transformative and affective capacities, including effects of interference and haptic dynamics – i.e. protocols of transmission and interaction. The expression that encapsulates its essence is: ACTIVE MATERIALITY RESUMEN El significado de la materia ha estado desde siempre ligado al pensamiento y el quehacer arquitectónico. Sin embargo, muchos intentos de capturar su esencia se han visto sumergidos en una tensión dialéctica entre la forma y la materialidad, entre la consistencia material y los modos inmateriales de la percepción, entre los estados estáticos y los procesos dinámicos, entre lo real y lo virtual, revelando una creciente conciencia de la desconcertante complejidad del mundo material. En esta complejidad, la noción de la operatividad o capacidad agencial– que emerge desde y dentro de los procesos ecológicos, políticos y socio-culturales– requiere de una reconceptualización de la materia y los procesos inherentes a la materialización, ofreciendo una nueva visión del contexto y el espacio, entendidos como un campo relacional dinámico. Oscilando entre el discurso arquitectónico y la práctica arquitectónica, y atravesando un extenso territorio trans-disciplinar, el objetivo de la presente tesis es ilustrar la variedad de metodologías proyectuales que emergieron desde este enfoque relacional. Concretamente, la intención es indagar en las epistemologías espaciales vinculadas a la noción de la atmósfera– generalmente asociada a la llamada Nueva Fenomenología–, reflexionando sobre su impacto en la producción arquitectónica. A continuación, el estudio ofrece una doble línea argumental. Primero, a través del análisis crítico de la noción de atmósfera, el objetivo es explorar maneras de pensar y dar forma a la realidad a través de las relaciones, reconociendo la mencionada complejidad del universo material revelado a través de fuerzas humanas y no-humanas, materiales e inmateriales. Segundo, a pesar de que el interés por las atmósferas ha florecido en las últimas décadas, la intención es demostrar que las bases conceptuales y los protocolos proyectuales de la creación de atmósferas se pueden encontrar bajo la superficie de los debates contemporáneos. Para corroborar e ilustrar estas hipótesis se propone una metodología de carácter arqueológico, trazando una particular genealogía de proyectos– la que se basa en una conciencia atmosférica. Asimismo, al definir esta conciencia atmosférica, el estudio explora tanto la naturaleza notoriamente ambigua y la dimensión dual de la atmósfera– meteorológica y estética–, como la heterogeneidad de significados derivados de ellas. En este contexto, la atmósfera se entiende como un concepto detonante, ya que sobrepasa los limites formales y materiales de los cuerpos, llevando a la re-evaluación de la experiencia perceptiva y abriendo a preguntas la ortodoxa relación espacio- cuerpo-ambiente. En consecuencia, la noción de la atmósfera ofrece a la arquitectura una dimensión expandida donde manifestarse, definiendo el espacio como una construcción contingente, performativa y afectiva, y presentando la materia como locus de producción/ actuación/ acción. Es precisamente esta dimensión expandida relacional la que constituye una base para lo que en el contexto del presente estudio se define como una tectónica afectiva. Es decir, una tectónica que representa una multiplicidad procesual y experiencial derivada de la convergencia entre el tiempo y el espacio, el cuerpo y el entorno, lo material y lo inmaterial; una tectónica en la que la materia no aparece como una substancia pasiva e inerte, ni es limitada al significado considerado tradicionalmente constructivo o a sus valores expresivos, sino que se presenta como elemento activo cargado de un potencial y vitalidad inherentes. A través de la definición de este tipo de materialismo afectivo, la intención es expandir el espectro de los atributos materiales, revelando las relaciones intrínsecas entre las propiedades físicas de los materiales y sus capacidades performativas, transformativas y afectivas, incluyendo efectos de interferencias y dinámicas hápticas– o dicho de otro modo, protocolos de transmisión e interacción. Una expresión que encapsula su esencia vendría a ser: MATERIALIDAD ACTIVA

GESTÃO DO CONHECIMENTO: UM ESTUDO SOBRE A RELAÇÃO ENTRE A LIDERANÇA TRANSFORMACIONAL, A CONVERSÃO DO CONHECIMENTO E A EFICÁCIA ORGANIZACIONAL

Este estudo teve como objetivo principal analisar a relação entre a Liderança Transformacional, a Conversão do Conhecimento e a Eficácia Organizacional. Foram considerados como pressupostos teóricos conceitos consolidados sobre os temas desta relação, além de recentes pesquisas já realizadas em outros países e contextos organizacionais. Com base nisto identificou-se potencial estudo de um modelo que relacionasse estes três conceitos. Para tal considera-se que as organizações que buscam atingir Vantagem Competitiva e incorporam a Knowledge-Based View possam conquistar diferenciação frente a seus concorrentes. Nesse contexto o conhecimento ganha maior destaque e papel protagonista nestas organizações. Dessa forma criar conhecimento através de seus colaboradores, passa a ser um dos desafios dessas organizações ao passo que sugere melhoria de seus indicadores Econômicos, Sociais, Sistêmicos e Políticos, o que se define por Eficácia Organizacional. Portanto os modos de conversão do conhecimento nas organizações, demonstram relevância, uma vez que se cria e se converte conhecimentos através da interação entre o conhecimento existente de seus colaboradores. Essa conversão do conhecimento ou modelo SECI possui quatro modos que são a Socialização, Externalização, Combinação e Internalização. Nessa perspectiva a liderança nas organizações apresenta-se como um elemento capaz de influenciar seus colaboradores, propiciando maior dinâmica ao modelo SECI de conversão do conhecimento. Se identifica então na liderança do tipo Transformacional, características que possam influenciar colaboradores e entende-se que esta relação entre a Liderança Transformacional e a Conversão do Conhecimento possa ter influência positiva nos indicadores da Eficácia Organizacional. Dessa forma esta pesquisa buscou analisar um modelo que explorasse essa relação entre a liderança do tipo Transformacional, a Conversão do Conhecimento (SECI) e a Eficácia Organizacional. Esta pesquisa teve o caráter quantitativo com coleta de dados através do método survey, obtendo um total de 230 respondentes válidos de diferentes organizações. O instrumento de coleta de dados foi composto por afirmativas relativas ao modelo de relação pesquisado com um total de 44 itens. O perfil de respondentes concentrou-se entre 30 e 39 anos de idade, com a predominância de organizações privadas e de departamentos de TI/Telecom, Docência e Recursos Humanos respectivamente. O tratamento dos dados foi através da Análise Fatorial Exploratória e Modelagem de Equações Estruturais via Partial Least Square Path Modeling (PLS-PM). Como resultado da análise desta pesquisa, as hipóteses puderam ser confirmadas, concluindo que a Liderança Transformacional apresenta influência positiva nos modos de Conversão do Conhecimento e que; a Conversão do Conhecimento influencia positivamente na Eficácia Organizacional. Ainda, concluiu-se que a percepção entre os respondentes não apresenta resultado diferente sobre o modelo desta pesquisa entre quem possui ou não função de liderança.

Alternative splicing, muscle calcium sensitivity, and the modulation of dragonfly flight performance

Calcium sensitivity of myosin cross-bridge activation in striated muscles commonly varies during ontogeny and in response to alterations in muscle usage, but the consequences for whole-organism physiology are not well known. Here we show that the relative abundances of alternatively spliced transcripts of the calcium regulatory protein troponin T (TnT) vary widely in flight muscle of Libellula pulchella dragonflies, and that the mixture of TnT splice variants explains significant portions of the variation in muscle calcium sensitivity, wing-beat frequency, and an index of aerodynamic power output during free flight. Two size-distinguishable morphs differ in their maturational pattern of TnT splicing, yet they show the same relationship between TnT transcript mixture and calcium sensitivity and between calcium sensitivity and aerodynamic power output. This consistency of effect in different developmental and physiological contexts strengthens the hypothesis that TnT isoform variation modulates muscle calcium sensitivity and whole-organism locomotor performance. Modulating muscle power output appears to provide the ecologically important ability to operate at different points along a tradeoff between performance and energetic cost.

Ecological chaos in the wake of invasion.

Irregularities in observed population densities have traditionally been attributed to discretization of the underlying dynamics. We propose an alternative explanation by demonstrating the evolution of spatiotemporal chaos in reaction-diffusion models for predator-prey interactions. The chaos is generated naturally in the wake of invasive waves of predators. We discuss in detail the mechanism by which the chaos is generated. By considering a mathematical caricature of the predator-prey models, we go on to explain the dynamical origin of the irregular behavior and to justify our assertion that the behavior we present is a genuine example of spatiotemporal chaos.

An experimental study on Aerobic Gymnastic: performance analysis as an effective evaluation for technique and teaching of motor gestures

Aerobic Gymnastic is the ability to perform complex movements produced by the traditional aerobic exercises, in a continuous manner, with high intensity, perfectly integrated with soundtracks. This sport is performed in an aerobic/anaerobic lactacid condition and expects the execution of complex movements produced by the traditional aerobic exercises integrated with difficulty elements performed with a high technical level. An inaccuracy about this sport is related to the name itself “aerobic” because Aerobic Gymnastic does not use just the aerobic work during the competition, due to the fact that the exercises last among 1’30” and 1’45” at high rhythm. Agonistic Aerobics exploit the basic movements of amateur Aerobics and its coordination schemes, even though the agonistic Aerobics is so much intense than the amateur Aerobics to need a completely different mix of energetic mechanisms. Due to the complexity and the speed with which you perform the technical elements of Aerobic Gymnastic, the introduction of video analysis is essential for a qualitative and quantitative evaluation of athletes’ performance during the training. The performance analysis can allow the accurate analysis and explanation of the evolution and dynamics of a historical phenomenon and motor sports. The notational analysis is used by technicians to have an objective analysis of performance. Tactics, technique and individual movements can be analyzed to help coaches and athletes to re-evaluate their performance and gain advantage during the competition. The purpose of the following experimental work will be a starting point for analyzing the performance of the athletes in an objective way, not only during competitions, but especially during the phases of training. It is, therefore, advisable to introduce the video analysis and notational analysis for more quantitative and qualitative examination of technical movements. The goal is to lead to an improvement of the technique of the athlete and the teaching of the coach.