Effects of Milling on Surface Integrity of Low-Carbon Steel

This work measured the effect of milling parameters on the surface integrity of low-carbon alloy steel. The Variance Analysis showed that only depth of cut did not influence on the workpiece roughness and the Pearson's Coefficient indicated that cutting speed was more influent than tool feed. All cutting parameters introduced tensile residual stress in workpiece surface. The chip formation mechanism depended specially on cutting speed and influenced on the roughness and residual stress of workpiece.

Spatial variability of soil water content and mechanical resistance of Brazilian ferralsol

The spatial variability of mechanical resistance to penetration (PR) and gravimetric moisture (GM) was studied at a depth of 0-0.40 m, in a ferralsol cropped with corn, and under conventional tillage in llha Solteira, Brazil (latitude 20 degrees 17'S, and longitude 52 degrees 25'W). The purpose of this study was to analyse and to try explaining the spatial variability of the mentioned soil physical properties using geostatistics. Soil data was collected at points arranged on the nodes of a mesh with 97 points. Geostatistics was used to analyse the spatial variability of PR and GM at four depths: 0-0. 1, 0.1-0.2, 0.2-0.3 and 0.3-0.4 m. PR showed a higher variability of data, with coefficients of variation of 52.39, 30.54, 16.91, and 15.18%, from the surface layers to the deepest layers. The values of the coefficients of variation for GM were lower: 9.99, 5.13, 5.59, and 5.69%. Correlation between GM and PR for the same soil layers was low. Penetration resistance showed spatial structure only in the 0.30-0.40 m layer, while gravimetric moisture showed spatial structure at all depths except for 0-0. 10 m. All the models of fitted semivariograms were spherical and exponential, with ranges of 10-80 m. Data for the variable 'GM' in the 0.20-0.30 and 0.30-0.40 m layers revealed a trend in data attributed to the occurrence of subsurface water flow. (C) 2005 Elsevier B.V. All rights reserved.

Sowing depths of brachiaria in intercropping with corn in no tillage planting

A produção de forragem na integração lavoura-pecuária é de suma importância, tanto para alimentação animal como para formação de palhada para plantio direto. O experimento foi conduzido no outono/inverno de 2009 e 2010, em Selvíria -MS, na Fazenda de Ensino, Pesquisa e Extensão da FEIS/UNESP. O objetivo foi avaliar a profundidade mais adequada para deposição das sementes de duas espécies de braquiárias em consórcio com milho, com ênfase para a produtividade do milho e formação de palha. O delineamento experimental foi em blocos ao acaso, em esquema fatorial 3 x 3, com quatro repetições. Os tratamentos principais foram duas espécies de braquiárias (Urochloa brizantha cv. Marandú e Urochloa ruziziensis), cujas sementes foram misturadas ao fertilizante do milho, e um tratamento-testemunha (sem consórcio). Os tratamentos secundários constituíram-se em três profundidades (8; 10 e 16 cm) de deposição do fertilizante (em consórcio e na testemunha). Os consórcios de milho com braquiária produziram quantidades de palha semelhantes. A produção total de palha foi maior nos consórcios e nas menores profundidades. O consórcio com U. ruziziensis propiciou maior produtividade de grãos de milho em relação ao com U. brizantha, em 2010. As profundidades de semeadura das forrageiras não afetaram a produtividade de milho.

The use of scaled semivariograms to plan soil sampling in sugarcane fields

Spatial sampling designs used to characterize the spatial variability of soil attributes are crucial for science studies. Sample planning for the interpolation of a regionalized variable may use several criteria, which could be best selected from an estimated semivariogram from a previously established grid. The objective of this study was to optimize the procedure for scaled semivariogram use to plan soil sampling in sugarcane fields in the Alfisol and Oxisol regions of Jaboticabal Town in So Paulo State, Brazil. A scaled semivariogram for several soil chemical attributes was estimated from the data obtained from two grids positioned on a sugarcane field area, sampled at a depth of 0.0-0.5 m. The research showed that regular grids with uniform intervals did not express the real spatial variability of the soil attributes of Oxisols and Alfisols in the study area. The calculated final sampling density based on the scaled parameters of the semivariogram was one sample for each 2 ha in Area 1 (convex landscape) and one sample for each 1 ha in Area 2 (linear landscape), as indicated by SANOS 0.1 software. The combined use of the simulation programs and scaled semivariograms can be used to define sampling points. These results may help in soil fertility mapping and thereby improve nutrient management in sugarcane crops.

A complete dosimetric characterization of two Sr-90-Y-90 dermatologic applicators

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Influence of the Connector and Implant Design on the Implant-Tooth-Connected Prostheses

Purpose:The purpose of this study was to evaluate stress transfer patterns between implant-tooth-connected prostheses comparing rigid and semirigid connectors and internal and external hexagon implants.Materials and Methods:Two models were made of photoelastic resin PL-2, with an internal hexagon implant of 4.00 x 13 mm and another with an external hexagon implant of 4.00 x 13 mm. Three denture designs were fabricated for each implant model, incorporating one type of connection in each one to connect implants and teeth: 1) welded rigid connection; 2) semirigid connection; and 3) rigid connection with occlusal screw. The models were placed in the polariscope, and 100-N axial forces were applied on fixed points on the occlusal surface of the dentures.Results:There was a trend toward less intensity in the stresses on the semirigid connection and solid rigid connection in the model with the external hexagon; among the three types of connections in the model with the internal hexagon implant, the semirigid connection was the most unfavorable one; in the tooth-implant association, it is preferable to use the external hexagon implant.Conclusions:The internal hexagon implant establishes a greater depth of hexagon retention and an increase in the level of denture stability in comparison with the implant with the external hexagon. However, this greater stability of the internal hexagon generated greater stresses in the abutment structures. Therefore, when this association is necessary, it is preferable to use the external hexagon implant.

Local application of tetracycline solution with a microbrush: An alternative treatment for persistent periodontitis

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Histometric analysis of ligature-induced periodontitis in rats: a comparison of histological section planes

The purpose of this study was to analyze the histometry of ligature-induced periodontitis in rats at different histological section depths. Sixteen male adult Wistar rats were randomly assigned to two groups: ligature and control. In the ligature group, rats received a sterile 4/0 silk ligature around the maxillary right 2nd molar. Thirty serial sections containing the 1st and 2nd molars, in which the coronal and root pulp, cementoenamel junction (CEJ) in the mesial side of the 2nd molar, interproximal alveolar bone and connective fiber attachment were clearly visible, were selected for histometric analysis. The histological sections were clustered in groups of 10 sections corresponding the buccal (B), central (C) and lingual (L) regions of the of periodontal tissue samples. The distance between the CEJ in the mesial side of the 2nd molar and the attached periodontal ligament fibers (CEJ-PL) as well as the distance between the CEJ and the alveolar bone crest (CEJ-BC) were determined. From CEJ-PL and CEJ-BC distances measured for each specimen, the measurements obtained in the B, L and C regions were recorded individually and together. Data were submitted to statistical analysis. Significant differences (p<0.001) were observed between the control and ligature groups regarding CEJ-PL (0.05 mm and 0.26 mm, respectively) and CEJ-BC (0.47 mm and 0.77 mm, respectively) measurements. Regarding the depth of the buccal, central and lingual planes, the means of CEJ-PL and CEJ-BC of both groups showed no statistically significant differences (p>0.05). In conclusion, the selection of 10 serial sections of the central region of periodontal tissue samples at any depth can be considered as representative for the evaluation of periodontal ligament fiber attachment and bone loss in ligature-induced periodontitis in rats.

Micromorphologic assessment of CVD (chemical vapor deposition) and conventional diamond tips and their cutting effectiveness

The aim of this study was to compare the micromorphology of CVD diamond tips coupled to ultrasound with conventional high speed diamond tips after cavity preparations, and to measure the width and depth of the cavities obtained. Two hundred bovine teeth were divided into 20 subgroups. Each of the diamond tips (10 CVD and 10 conventional) were used to prepare 10 standardized cavities, using an apparatus that controlled the time (t: 27 s), speed (5.3 mm/s) and load (0.012 KGF) of the tip against the teeth during preparation. The unused and the used (after one, five and 10 preparations) tips were analyzed by scanning electronic microscopy. The images were randomly assessed by 3 examiners with regard to the presence or absence of micromorphologic alterations. Cavity measurements were made after visualization under a stereoscopic microscope. Cavity widths and depths were analyzed by the ANOVA Factorial test (p < 0.05). The CVD diamond tips presented less wear than the conventional tips after all the cavity preparations performed, but produced shallower cavities that were equivalent in width to those made by conventional tips after the fifth preparation. CVD diamond tips may be suggested as an alternative to conventional diamond tips due to their conservative preparation and greater longevity.

Effect of the Insertion and Polymerization Technique in Composite Resin Restorations: Analysis of Marginal Gap by Atomic Force Microscopy

This in vitro study evaluated the marginal gap at the composite tooth/resin interface in class V cavities under the influence of two insertion techniques and a curing system by means of atomic force microscopy (AFM). Forty enamel and dentin cavities were prepared on the buccal surface in bovine teeth with quadratic forms measuring 2 mm X 2 mm and depth of 1.5 mm. The teeth were then divided into four groups: group A, 10 cavities were restored in one increment, light cured by halogen light; group B, 10 cavities filled with bulk filling, light cured by the light emitting diodes (LED); group C, 10 cavities were restored by the incremental technique, light cured by halogen light; group D, 10 cavities were restored by the incremental technique, light cured by the LED. The teeth underwent the polishing procedure and were analyzed by AFM for tooth/restoration interface evaluation. The data were compared between groups using the nonparametric Kruskall-Wallis and Mann-Whitney tests (p < 0.05). The results showed a statistically significant difference between groups A and B and groups A and C. It was concluded that no insertion and polymerization technique was able to completely seal the cavity.

Effect of different dental composite resins on the polymerization process

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Penetration into dentin of sodium hypochlorite associated with acid solutions

Objective. The objective of this study was to evaluate the penetration of 2.5% NaOCl associated with 17.0% EDTA, 1.0% citric acid, and 1.0% peracetic acid into dentin tubules.Study design. The roots of 44 bovine incisors were cross-sectioned and 5-mm-long fragments were produced from their middle thirds. The specimens were instrumented with ProTaper hand files, stained in crystal violet, then sectioned mesiodistally. The buccal fragments were divided into 4 groups (n = 9) and subjected to 2 consecutive 10-minute immersion periods in one of the following acid solutions combined with 2.5% NaOCl: 17.0% EDTA (group 1), 1.0% citric acid (group 2), and 1.0% peracetic acid (group 3). Nine fragments were immersed in 2.5% NaOCl (group 4). The analysis of the penetration of NaOCl solutions into dentin was performed by measuring the depth of crystal violet stain that was bleached using a steromicroscope under x50 magnification. Statistical comparisons were carried out by Kruskal-Wallis and Dunn's tests at the 5% significance level.Results. Group 1 showed less penetration into dentin than group 4 (P < .05). No statistically significant differences were observed among groups 2, 3, and 4 (P > .05).Conclusions. Association of NaOCl with acid solutions did not increase its penetration depth into root dentin. (Oral Surg Oral Med Oral Pathol Oral Radiol Endod 2011;112:e155-e159)

Morphometric analysis of the intestine of domestic quails (Coturnix coturnix japonica) treated with different levels of dietary calcium

The aim of this study was to perform a morphometric analysis of the various parts of the intestine of the domestic quail. Twenty-four female quails (Coturnix coturnix japonica) aged 37 weeks were used and accommodated in laying cages for 12 weeks. Each group was fed a standardized diet containing different quantities of calcium: 2.0%, 2.5%. 3.0% and 3.5%. The birds were weighed, killed, and samples of 1 cm were collected from the duodenum, jejunum and ileum and submitted to the histological routine. The sections obtained were stained in haematoxylin & eosin (H&E). For morphometric analysis, 30 villi and 30 crypts of each segment of the small intestine were measured in order to determine the height and area of the villi, as well as the depth of the crypts. The results showed that although the integrity of the gastrointestinal tract was maintained in all the birds treated with the different calcium levels, a calcium level of 3.0% showed the most promise, as the levels of 2.0% and 2.5% did not cause any alteration in the intestinal tract. Furthermore, a calcium level of 3.5% led to a significant reduction in the height of the villosities, and in consequence reduced the digestive and absorptive capabilities.

Diel variations in decapod catch rate and size of captured individuals in a subtropical area of Brazil

Diel variations in decapod crustaceans catch rate, as well as variations in size of sampled individuals, were investigated in a sublittoral portion of Ubatuba Bay (23 degrees 20', 23 degrees 35'S and 44 degrees 50', 45 degrees 14'W) in order to detect differential patterns of occurrence. Three replicate trawls, each enclosing a 2,500 m(2) area, were performed at a median depth of 3.5 m during the waning moon period, in 3 consecutive summer and winter months. Trawls were conducted at dawn, noon, dusk and midnight. Hydrological and substratum features were monitored. Penaeoideans did not show a significant diel catch rate variation during the sampling periods, but the catch rate of brachyurans was highest at dusk and midnight during winter (p < 0.01). Fixing diel variation, catch rates of both brachyurans and penaeoideans are subjected to significant seasonal differences (p < 0.05). The largest specimens of Callinectes ornatus, Xiphopenaeus kroyeri, Rimapenaeus constrictus and Farfantepenaeus spp were found at twilight during summer. Differences on size of captured individuals mainly in samples of portunids and penaeids taken during the course of the day evidences that significant daily movements take place. This confirms that activity alterations depend on characteristics of daily schedules and on environmental demands of studied species.

Diel comparison of the catch and size of the shrimp artemesia longinaris (dendrobranchiata, penaeidae) in the ubatuba region, northern coast of the state of São Paulo

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)