Nanocompósito de poliestireno reciclado, bentonita sódica e hemi-hidrato de sulfato de cálcio: obtenção e caracterização.

Nesta Tese foram preparados, em solução, filmes híbridos de argila e poliestireno provenientes de copos descartáveis comercializados no mercado brasileiro, com acetato de etila e glicerol. Posteriormente, foi adicionado o Hemi-hidrato de sulfato de cálcio como carga de reforço. Tanto a argila quanto o glicerol, assim como o hemihidrato de sulfato de cálcio, foram utilizados nos percentuais relativos à massa do poliestireno fragmentado correspondendo a 1%,2%, 3%,4%, 5% e 7%. Dos filmes, nos percentuais 3, 4, 5 e 7, exclui-se o percentual de 4% e os demais foram fragmentados e submetidos a extrusão, com resfriamento natural, à seco, produzindo-se grãos com os quais foi avaliado o índice de fluidez e injetados para a moldagem de corpos de prova rígidos. O desempenho dos corpos rígidos, foi comparado com os resultados do HIPS 484, e o GPPS comercializados no mercado brasileiro. Os filmes foram caracterizados por difração de raios X, microscopia eletrônica de varredura (MEV), calorimetria exploratória diferencial (DSC), além dos testes de resistência à tração, fluorescência de raios X, EDS e FTIR. Amostra do filme, ultrafino, obtido a partir da solução com o percentual de 5% foi observada ao microscópio ótico e no microscópio eletrônico de transmissão, assim como amostras de corpos rígidos microtomizadas. Nos corpos rígidos, além das análises instrumentais citadas, foram avaliadas a resistência à flexão, modulo de flexão, resistência à tração, alongamento e resistência ao impacto Izod. O desempenho sob chama foi avaliado em amostras de filme e também do corpo rígido. Resultados do DRX, e da MET foram coerentes com a bibliografia para nanocompósitos argila-polímero e, associado às respostas dos demais ensaios, indicaram um material de boa qualidade morfológica e boas propriedades mecânicas comparadas ao HIPS 484 e ao GPPS. Sob a chama o material produzido apresentou maior resistência à queima avaliado pela quantidade aparente de material residual para um mesmo tempo sob fogo. Constatou-se, também, uma boa dispersão das cargas na matriz polimérica, assim como uma adequada interação entre os elementos orgânicos e inorgânicos do material, a delaminação parcial da argila e quebra da estrutura do hemi-hidrato. Isto resultou em um bom desempenho mecânico e térmico do compósito que pode ser atribuído, tanto a uma forte influência dos íons metálicos presentes nas cargas inorgânicas, quanto às adições presentes na formulação dos copos descartáveis.

Tratamento de lesões white spot pelo sistema fosfato de cálcio caseína-fosfopeptideo amorfo (CPP-ACP): prevenção secundária

Dissertação para obtenção do grau de Mestre no Instituto Superior de Ciências da Saúde Egas Moniz

Quintosana e seus derivados conjugados com ácido gálico: avaliação de seu potencial antioxidante e de interferência na formação de cristais de oxalato de cálcio

Chitin is the second most abundant polysaccharide in nature and its derivative chitosan has been widely studied due to its unique chemical and pharmacological properties. However, studies show that when this molecule is used as food, drug, etc. it tends to accumulate in renal tissue and promotes an increase in calcium excretion. Nevertheless, the effect of chitosan on the formation of calcium oxalate (OxCa) crystals has never been evaluated. The formation of kidney stones (urolithiasis) is the disease that most often affects the kidneys and the urinary system. In addition, this is a disease with high prevalence and recurrence. Many molecules with antioxidant activity have been shown to decrease the potential for in vitro OxCa crystals formation. Thus, the aim of this study was to evaluate the effect of low molecular weight chitosan and its derivatives conjugated to gallic acid (AG) as antioxidant and inhibitor of OxCa crystals formation. The physico-chemical analysis confirmed the identity of chitosan. This molecule was subjected to five antioxidant tests and showed an excellent copper chelating activity. However, chitosan did not show other significant antioxidant activity. When chitosan was subjected to in vitro crystal formation tests, it increased the number of OxCa monohydrate crystals, modified the morphology of the crystals, modified the proportions between populations of crystals in solution and increased the zeta potential of these crystals formed. Four molecules of chitosan conjugated with GA were obtained. The physico-chemical analysis confirmed that chitosan and AG were covalently bonded. However, the amount of GA liked to chitosan did not increase even when 10 times more GA was used in experiment. When these derivatives were subjected to antioxidant tests, all chitosan conjugates showed higher antioxidant potential than their precursors. However, they showed different activity between them, which indicating that the position where AG is conjugated is an important factor for chitosan-GA activity. When conjugated chitosans were submitted to in vitro crystal formation tests, a reduction in the crystals number was observed when compared with those formed in the presence of unconjugated chitosan. Chitosan has a strong capacity for inducing OxCa monohydrate crystal formation, as well as modify their morphology and zeta potential. Over all, the process of conjugating AG to chitosan led to an increase in antioxidant potential of this molecule and was also able to decrease its capacity of inducing in vitro crystal formation

Uso de água produzida na formulação de fluidos de perfuração

Drilling fluids have fundamental importance in the petroleum activities, since they are responsible for remove the cuttings, maintain pressure and well stability, preventing collapse and inflow of fluid into the rock formation and maintain lubrication and cooling the drill. There are basically three types of drilling fluids: water-based, non-aqueous and aerated based. The water-based drilling fluid is widely used because it is less aggressive to the environment and provide excellent stability and inhibition (when the water based drilling fluid is a inhibition fluid), among other qualities. Produced water is generated simultaneously with oil during production and has high concentrations of metals and contaminants, so it’s necessary to treat for disposal this water. The produced water from the fields of Urucu-AM and Riacho da forquilha-RN have high concentrations of contaminants, metals and salts such as calcium and magnesium, complicating their treatment and disposal. Thus, the objective was to analyze the use of synthetic produced water with similar characteristics of produced water from Urucu-AM and Riacho da Forquilha-RN for formulate a water-based drilling mud, noting the influence of varying the concentration of calcium and magnesium into filtered and rheology tests. We conducted a simple 32 factorial experimental design for statistical modeling of data. The results showed that the varying concentrations of calcium and magnesium did not influence the rheology of the fluid, where in the plastic viscosity, apparent viscosity and the initial and final gels does not varied significantly. For the filtrate tests, calcium concentration in a linear fashion influenced chloride concentration, where when we have a higher concentration of calcium we have a higher the concentration of chloride in the filtrate. For the Urucu’s produced water based fluids, volume of filtrate was observed that the calcium concentration influences quadratically, this means that high calcium concentrations interfere with the power of the inhibitors used in the formulation of the filtered fluid. For Riacho’s produced water based fluid, Calcium’s influences is linear for volume of filtrate. The magnesium concentration was significant only for chloride concentration in a quadratic way just for Urucu’s produced water based fluids. The mud with maximum concentration of magnesium (9,411g/L), but minimal concentration of calcium (0,733g/L) showed good results. Therefore, a maximum water produced by magnesium concentration of 9,411g/L and the maximum calcium concentration of 0,733g/L can be used for formulating water-based drilling fluids, providing appropriate properties for this kind of fluid.

Caracterização físico-química e química do fruto do juazeiro (Ziziphus joazeiro Mart) e avaliação da sua conservação por fermentação láctica

Considering the plant biodiversity in the Brazilian Northeast, whose components can be inserted into sustainable production systems, the jujube (Ziziphus joazeiro Mart.) emerges as to recovery of its fruit. The present study has as objective to characterize the fruit of the jujube under the physical, physicochemical and chemical approach and assess its conservation by spontaneous lactic fermentation under the influence of chloride, sodium, calcium and potassium. According to the legislation, vegetable acidified by fermentation that is subjected to lactic acid fermentation in order to achieve a final product pH less than or equal to 4.5. The results of the physical, chemical and physico-chemistry of ripe fruit jujube showed the potential of this species for agro-processing. The yield of edible portion (91.83%), soluble solids content (18,98º Brix), titratable acidity (0.14% citric acid), pH (5.30) and its composition, divided in moisture (79.01%), protein (2.01%), lipids (0.52%), carbohydrate (17.59%), fiber, ash (0.76%) and its minerals were consistent with the characteristic profile fruits, thus favoring the development of spontaneous lactic fermentation. The minimum pH and titratable acidity observed maximum in the fermentation process under the influence of mixtures of salts (NaCl and KCl NaCl2) values ranged from 3.4 to 3.7 and from 0.54 to 0.95 (% lactic acid), respectively. The profile of the lactic fermentation of fruit of jujube in brine, fermented microbiological quality and the result of analysis of primary sensory prepared preserved, the application of endorsed by the consumer sensory evaluation, more particularly, derived from fermented fruit preserved in the presence of chloride sodium, in accordance with the traditional techniques of lactic fermentation of vegetables. The results of sensory evaluation conducted with 100 consumers (tasters) revealed an acceptance rate equal to 78% of the preserve. Despite restrictions on the sensory acceptability of fermented under the influence of salts (KCl and CaCl2) substitutes sodium chloride, preserved these perspectives presented to balance the optimization of mixtures, health product safety and consumer awareness towards prefer a more healthy product with reduced sodium content.

Contribuição da poliacrilamida parcialmente hidrolisada em associação com a bentonita em fluidos de perfuração aquosos

In this study, we investigated the effect of addition of partially hydrolyzed polyacrylamide (HPAM) and bentonite in the physicochemical properties of acquous drilling fluids. Two formulations were evaluated: F1 formulation, which was used as reference, containing carboxymethylcellulose (CMC), magnesium oxide (MgO), calcite (calcium carbonate - CaCO3 ), xanthan gum, sodium chloride (NaCl) and triazine (bactericidal); and F2, containig HPAM steady of CMC and bentonite in substituition of calcite. The prepared fluids were characterized by rheological properties, lubricity and fluid loss. Calcite was characterized by granulometry and thermal gravimetric analysis (TGA). The formulation F2 presented filtration control at 93◦C 34 mL while F1 had total filtration. The lubricity coefficient was 0.1623 for F2 and 0.2542 for F1, causing reduction in torque of 25% for F1 and 52 % for F2, compared to water. In the temperature of 49 ◦C and shear rate of 1022 s −1 , the apparent viscosities were 25, 5 and 48 cP for F1 and F2 formulation, respectively, showing greater thermal resistance to F2. With the confirmation of higher thermal stability of F2, factorial design was conducted in order to determine the HPAM and of bentonite concentrations that resulted in the better performance of the fluids. The statistical design response surfaces indicated the best concentrations of HPAM (4.3g/L) and bentonite (28.5 g/L) to achieve improved properties of the fluids (apparent viscosity, plastic viscosity, yield point and fluid loss) with 95% confidence, as well as the correlations between these factors (HPAM and bentonite concentrations). The thermal aging tests indicated that the formulations containing HPAM and bentonite may be used to the maximum temperature until 150 ◦C. The analyze of the filter cake formed after filtration of fluids by X-ray diffraction showed specific interactions between the bentonite and HPAM, explaining the greater thermal stability of F2 compared to the fluid F1, that supports maximum temperature of 93 ◦C.

Estudo das alterações hematológicas e urinárias em cães em diferentes estágios de disfunção renal e avaliação do biomarcador cistatina C

Chapter 2 - Cystatin C is a cationic protein is not glycosylated, produced a steady state for all nucleated and present in biological fluids cells being freely filtered by the glomeruli and almost completely catabolized in the proximal tubule, it is a promising early renal dysfunction marker. This study aimed to determine and compare the serum concentration of cystatin C biomarker in 86 dogs. The animals were divided into four groups according to serum creatinine levels: G1 - up. 1.4 mg / dL (23 animals), G2 - 1.5-2.0 mg / dL (16 animals), G3 - 2.1 to 5.0 mg / dL (24 animals) and G4 - above 5.1 mg / dL (23 animals). There was the measurement of the parameters used in the clinical routine of small animals such as urea, urinary gamma glutamyl transferase, proteinuria, alkaline phosphatase, sodium, potassium, chloride, calcium, phosphorus, calcium/phosphorus ratio and cystatin C. There was no statistical difference for urea, proteinuria, phosphorus, calcium/phosphorus, potassium and cystatin C, however, the other showed no statistical difference. Based on the results we can infer that cystatin C was not a good early indicator of kidney disease in dogs. Chapter 3 - This study aimed to determine the hematological and urinalysis elements such as density, proteinuria, cylinders and pH in 86 dogs The animals were divided into four stages according to serum creatinine levels: I - up to 1.4 mg/dL (23 animals), II - 1.5-2.0 mg/dL (16 animals), III from 2.1 to 5.0 mg/dL (24 animals) and IV - above 5.1 mg/dL (23 animals). In stage III, IV there was anemia normocytic normochromic type. Stage II had a leukocytosis frame by neutrophilia with a regenerative left shift and stage III and IV detour degenerative left. The density remained within the reference values all stages. Proteinuria showed statistical significance for the classification 2+ (1.0 g/L), between stage I and II, II and IV. Only the cylinder granular statistical difference in the classification 2+ between stage II and III, and 3+ between stage I and III. The prevailing pH was acid. The haematological values compared to serum creatinine stages showed the changes in hemoglobin and packed cell volume erythrocytes become more pronounced as serum creatinine values rise , this is also the behavior of neutrophils rods and proteinuria.

Níveis de cálcio e relação cálcio: fósforo em rações para poedeiras leves de 24 a 40 semanas de idade

v. 17, n. 2, p. 206-216, abr./jun. 2016.

Cimentos injetáveis à base de fosfatos de cálcio para vertebroplastia

O principal objectivo desta investigação foi o desenvolvimento cimentos de fosfatos de cálcio com injetabilidade melhorada e propriedades mecânicas adequadas para aplicação em vertebroplastia. Os pós de fosfato de tricálcico (TCP) não dopados e dopados (Mg, Sr e Mn) usados neste estudo foram obtidos pelo processo de precipitação em meio aquoso, seguidos de tratamento térmico de forma a obter as fases pretendidas, α− e β−TCP. A substituição parcial de iões Ca por iões dopantes mostrou ter implicações em termos de estabilidade térmica da fase β−TCP. Os resultados demonstraram que as transformações de fase alotrópicas β↔α−TCP são fortemente influenciadas por variáveis experimentais como a taxa de arrefecimento, a presença de impurezas de pirofosfato de cálcio e a extensão do grau de dopagem com Mg. Os cimentos foram preparados através da mistura de pós, β−TCP (não dopados e dopados) e fosfato monocálcico monidratado (MCPM), com meios líquidos diferentes usando ácido cítrico e açucares (sucrose e frutose) como agentes retardadores de presa, e o polietilenoglicol, a hidroxipropilmetilcelulose e a polivinilpirrolidona como agentes gelificantes. Estes aditivos, principalmente o ácido cítrico, e o MCPM aumentam significativamente a força iónica do meio, influenciando a injetabilidade das pastas. Os resultados também mostraram que a distribuição de tamanho de partícula dos pós é um factor determinante na injetabilidade das pastas cimentícias. A combinação da co-dopagem de Mn e Sr com a adição de sucrose no líquido de presa e com uma distribuição de tamanho de partícula dos pós adequada resultou em cimentos de brushite com propriedades bastante melhoradas em termos de manuseamento, microestrutura, comportamento mecânico e biológico: (i) o tempo inicial de presa passou de ~3 min to ~9 min; (ii) as pastas cimentícias foram totalmente injectadas para uma razão liquido/pó de 0.28 mL g−1 com ausência do efeito de “filter-pressing” (separação de fases líquida e sólida); (iii) após imersão numa solução durante 48 h, as amostras de cimento molhadas apresentam uma porosidade total de ~32% e uma resistência a compressão de ~17 MPa, valor muito superior ao obtido para os cimentos sem açúcar não dopados (5 MPa) ou dopados só com Sr (10 MPa); e (iv) o desempenho biológico, incluindo a adesão e crescimento de células osteoblásticas na superfície do cimento, foi muito melhorado. Este conjunto de propriedades torna os cimentos excelentes para regeneração óssea e engenharia de tecidos, e muito promissores para aplicação em vertebroplastia.

Scaffolds porosos à base de fosfatos de cálcio para regeneração óssea

Graças ao aumento da esperança média de vida do ser humano, a engenharia de tecidos tem sido uma área alvo de enorme investigação. A utilização de estruturas tridimensionais porosas e biodegradáveis, denominadas de scaffolds, como matriz para a adesão e proliferação celular tem sido amplamente investigada. Existem atualmente diversas técnicas para a produção destas estruturas mas o grau de exigência tem vindo a aumentar, existindo ainda lacunas que necessitam ser preenchidas. A técnica de robocasting consiste numa deposição camada a camada de uma pasta coloidal, seguindo um modelo computorizado (CAD) e permite a produção de scaffolds com porosidade tamanho de poro e fração de porosidade controlados, boa reprodutibilidade, e com formas variadas, as quais podem ser idênticas às dos defeitos ósseos a preencher. O presente estudo teve como objetivo produzir scaffolds porosos à base de fosfatos de cálcio através de robocasting. Para tal, foram estudadas duas composições de pós à base de β-TCP, uma pura e outra co-dopada com estrôncio, zinco e manganês. Inicialmente os pós foram sintetizados pelo método de precipitação química por via húmida. Após a síntese, estes foram filtrados, secos, calcinados a 1000ºC e posteriormente moídos até possuírem um tamanho médio de partícula de cerca de 1,5 μm. Os pós foram depois peneirados com uma malha de 40μm e caracterizados. Posteriormente foram preparadas várias suspensões e avaliado o seu comportamento reológico, utilizando Targon 1128 como dispersante, Hidroxipropilmetilcelulose (HPMC) como ligante e polietilenimina (PEI) como agente floculante. Por fim, e escolhida a melhor composição para a formação da pasta, foram produzidos scaffolds com diferentes porosidades, num equipamento de deposição robótica (3D Inks, LLC). Os scaffolds obtidos foram secos à temperatura ambiente durante 48 horas, sinterizados a 1100ºC e posteriormente caracterizados por microscopia eletrónica de varrimento (SEM), avaliação dos tamanhos de poro, porosidade total e testes mecânicos. Ambas as composições estudadas puderam ser transformadas em pastas extrudíveis, mas a pasta da composição pura apresentou uma consistência mais próxima do ideal, tendo originado scaffolds de melhor qualidade em termos de microestrutura e de propriedades mecânicas.

Polissacarídeos sulfatados da Alga Marrom Dictyopteris justii como agentes antioxidantes e inibidores da formação de cristais de oxalato de cálcio

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior

Quantificação do ião cálcio nas uvas e vinhos brancos por espectroscopia de infravermelho

Com o objetivo de diminuir a incidência das leveduras encapsulas em alginato se aglomerarem na segunda fermentação em garrafa e reduzir custos associados à sua eliminação, pretendeu-se utilizar a metodologia NIR para determinar a quantidade de cálcio no vinho. Foram quantificados outros minerais para avaliar hipotéticos antagonismos iónicos. Observou-se também que este controlo de qualidade poderá ser efetuado no mosto. Atualmente este controlo é realizado por metodologias de análise de referência bastante morosas como EAA. Contudo a metodologia NIR demonstrou ser uma boa alternativa no controlo dos parâ-metros de qualidade na produção de vinho espumante, permitindo a diminuição do tempo de análise e de resíduos. No desenvolvimento dos modelos matemáticos para a calibração do NIR utilizaram-se 79 vinhos brancos e 60 amostras de mosto. Foram desenvolvidos 11 modelos de calibração onde o coeficiente de correlação foi, em aproximadamente 58% dos casos, maior que 0,99; ABSTRACT: In order to reduce the incidence of alginate beads aggregation during the second fermentation in the bottle and to reduce costs associated with their disposal, it was used the NIR technology to quantify calcium content in the wine. Other minerals were also quantified in order to evaluate possible ionic antagonisms. Quality control is usually done in the base wine but it can also be evaluated in the must. Currently this control was carried out by reference analysis methodologies generally rather slow as AAS. However NIR proved to be a good alternative technique in the control of quality parameters of wine production, allowing the reduction of the analysis time and waste. In order to develop mathematical models for the calibration of NIR it was used 79 white wine samples and 60 must samples. Eleven calibration models have been developed, where the correlation coeffi-cient was, in approximately 58% of cases, greater than 0,99.

Influência da adição de cálcio nas propriedades de pastas geopoliméricas destinadas a cimentação de poços de petróleo

Nowadays, the search for new technologies that are able to follow the upcoming challenges in oil industry is a constant. Always trying properties improvements of the used materials, looking for the best performance and greater life time. Besides the search for technologies that show an improvement of performance, the search for materials environmentally correct along the whole production process. In Oil well cementing, this search for new technologies passes through the development of slurry systems that support these requests and that are also environmentally friendly. In this context, the use of geopolymer slurries is a great alternative route to cementing oil wells. Besides having good properties, comparable to Portland cement slurries, this alternative material releases much less CO2 gas in the production of their root materials when compared the production of Portland cement, which releases tons of CO2. In order to improve the properties of geopolymer slurries has been added Calcium Oxide, as observed in other studies that slurries where the Calcium is present the values of compressive strength is greater. The addition has been realized based in the CaO/SiO2 molar ratio of 0.05, 0.10 and 0.15. Have been performed compressive strength tests, thickening time, rheology and fliud loss control test of the slurries, following NBR 9831, as well as the physical chemical characterization of XRD, SEM and TG. Has been observed in most of the tests the slurries follow a tendency until the ratio of 0.10, which inverses in the ratio 0.15. This behavior can be explained by two phenomena that occur simultaneously, the first one is the break of the polymer chains and a consequent increase in molucules mobility, which prevails until the ratio of 0.1, and the second is possible approach of the chains due to the capacity of the calcium ions stabilize the charges of two different aluminum. There is only one linearity in the mechanical behavior that can be attributed to the appereance of the C-S-H phase. Based on this, it is concluded that the phenomenon of breaking the polymer chains predominates until the ratio of 0.1, causing an increase of the filtrate volume, lower rheological parameters and increasing thickening time. From the ratio of 0.15 the approach of the chains predominates, and the behavior is reversed