Lateral torsional buckling behaviour of cold-formed steel beams at elevated temperatures

Abstract: This paper presents the details of a study into the behaviour and moment capacities of cold-formed steel lipped channel beams (LCB) subject to lateral-torsional buckling at elevated temperatures. It was based on a validated numerical model of a simply supported and laterally unrestrained LCB subjected to a uniform moment. The ultimate moment capacities from this study were compared with the predicted values using ambient and fire design methods. This study showed that the lateral torsional buckling capacity is strongly influenced by the level of non-linearity in the stress-strain curves of steel at elevated temperatures. Hence most of the current design methods based on a single buckling curve were not adequate to determine the moment capacities. This paper proposes a new design method for the cold-formed steel LCBs subject lateral-torsional buckling at elevated temperatures.

Investigation into the transport, behaviour and deposition of combustion aerosols from transport sources

The deterioration of air quality is a significant issue in large and growing cities. This work investigates particulate emissions from transport, the largest source of air pollution in cities today. Emitters such as busy roads and diesel trains are investigated, with specific reference to the evolution of particles over time and distance. Diesel trains are investigated as an alternative to road traffic in investigating evolutionary processes. Higher emissions and solitary sources mean that the emitted plume can be observed over time in a single location. These results represent the first investigation of the evolution of fine and ultrafine aerosol particles from this type of source. Aerosols near a busy road are investigated, with the result that a dependence of total number concentration on distance from the road is shown to be related to the fragmentation of nanoparticle clusters. Local meteorological conditions are also monitored and humidity is shown to vary with distance from the road in a nonmonotonic way. Particles from a busy road were also examined using a scanning electron microscope, with the intention of understanding the make up of the emitted aerosol plume. It was determined that due to significant surface behaviour post-deposition, this method of analysis could not directly classify airborne pollutants. Some interesting results were obtained however, particularly in terms of composite particles and the analysis of deposited patterns. This thesis introduces new work in terms of the analysis of diesel train particulate emissions, as well as adding further evidence towards the fragmentation process of aerosol evolution in both background concentrations and emitted aerosol plumes.

Mapping Services to Support a Patient's Journey through Evidence-Based Care Pathways After a Cardiac Event

Background: There are inequalities in geographical access and delivery of health care services in Australia, particularly for cardiovascular disease (CVD), Australia's major cause of death. Analyses and models that can inform and positively influence strategies to augment services and preventative measures are needed. The Cardiac-ARIA project is using geographical spatial technology (GIS) to develop a national index for each of Australia's 13,000 population centres. The index will describe the spatial distribution of CVD health care services available to support populations at risk, in a timely manner, after a major cardiac event. Methods: In the initial phase of the project, an expert panel of cardiologists and an emergency physician have identified key elements of national and international guidelines for management of acute coronary syndromes, cardiac arrest, life-threatening arrhythmias and acute heart failure, from the time of onset (potentially dial 000) to return from the hospital to the community (cardiac rehabilitation). Results: A systematic search has been undertaken to identify the geographical location of, and type of, cardiac services currently available. This has enabled derivation of a master dataset of necessary services, e.g. telephone networks, ambulance, RFDS, helicopter retrieval services, road networks, hospitals, general practitioners, medical community centres, pathology services, CCUs, catheterisation laboratories, cardio-thoracic surgery units and cardiac rehabilitation services. Conclusion: This unique and innovative project has the potential to deliver a powerful tool to both highlight and combat the burden of disease of CVD in urban and regional Australia.

Obtaining peak performance in the transition to Higher Education: Support for the worried well, acutely anxious and seriously sluggish student

Research suggests that students in their late teens and early twenties have not reached "identity formation" (James Marcia, 1969, 1980). The heightened anxiety and uncertainty about themselves and their future contribute to sometimes crippling fears emanating as anxiety, clinical depression and other mood disorders. This paper will explore some issues and suggest healthy ways of helping young people safely through these chaotic years and into a fulfilling career.

Ethical issues in research on adolescent depression and suicidal behaviour

Argues that the codes of ethical conduct of the Australian Psychological Society and the American Psychological Association imply that researchers of adolescent depression and suicidal behavior must plan to intervene to assess risk where a participant in a study indicates an intention to commit suicide. Participants in research of this kind need to be advised of this possibility in advance. The obligation to intervene, and to advise of the possibility of intervention, poses practical and methodological problems for research in this area but does not, it is argued, absolve the researcher of the primary responsibility to contribute to the welfare of the research participant. This obligation exists only when there is indication of harm but not, for instance, in the case of depression without suicidal intent.

The use of virtual prototyping for hazard identification in the early design stage

Purpose: The construction industry is well known for its high accident rate and many practitioners consider a preventative approach to be the most important means of bringing about improvements. This paper addresses previous research and the weaknesses of existing preventative approaches and a new application is described and illustrated involving the use of a multi-dimensional simulation tool - Construction Virtual Prototyping (CVP). Methodology: A literature review was conducted to investigate previous studies of hazard identification and safety management and to develop the new approach. Due to weaknesses in current practice, the research study explored the use of computer simulation techniques to create virtual environments where users can explore and identify construction hazards. Specifically, virtual prototyping technology was deployed to develop typical construction scenarios in which unsafe or hazardous incidents occur. In a case study, the users’ performance was evaluated their responses to incidents within the virtual environment and the effectiveness of the computer simulation system established though interviews with the safety project management team. Findings: The opinions and suggestions provided by the interviewees led to the initial conclusion that the simulation tool was useful in assisting the safety management team’s hazard identification process during the early design stage. Originality: The research introduces an innovative method to support the management teams’ reviews of construction site safety. The system utilises three-dimensional modelling and four-dimensional simulation of worker behaviour, a configuration that has previously not been employed in construction simulations. An illustration of the method’s use is also provided, together with a consideration of its strengths and weaknesses.

Antecedents of sustainable management support for IT-related initiatives

Having IT-related capabilities is not enough to secure value from the IT resources and survive in today’s competitive environment. IT resources evolve dynamically and organisations must sustain their existing capabilities to continue to leverage value from their IT resources. Organisations’ IT-related management capabilities are an important source of their competitive advantage. We suggest that organisations can sustain these capabilities through appropriate considerations of resources at the technology-use level. This study suggests that an appropriate organisational design relating to decision rights and work environment, and a congruent reward system can create a dynamic IT-usage environment. This environment will be a vital source of knowledge that could help organisations to sustain their IT-related management capabilities. Analysis of data collected from a field survey demonstrates that this dynamic IT-usage environment, a result of the synergy between complementary factors, helps organisations to sustain their IT-related management capabilities. This study adds an important dimension to understanding why some organisations continue to perform better with their IT resources than others. For practice, this study suggests that organisations need to consider a comprehensive approach to what constitutes their valuable resources.

Commentaries and Responses to "The Driver Behaviour Questionnaire as a predictor of accidents: A meta-analysis" [Commentaries lead by Anders af Wahlberg; Responses lead by J.C.F. de Winter]

The following discussion is in response to a 2010 article published in the Journal of Safety Research by J.C.F. de Winter and D. Dodou entitled “The Driver Behaviour Questionnaire as a predictor of accidents: A meta-analysis” (Volume 41, Number 6, pp. 463-470, available on sciencedirect.com). The editors are pleased to provide a forum for this exchange and welcome further comments.

Incentivising private health insurance through the income tax regime : Capitalising on behavioural models

The Australian income tax regime is generally regarded as a mechanism by which the Federal Government raises revenue, with much of the revenue raised used to support public spending programs. A prime example of this type of spending program is health care. However, a government may also decide that the private sector should provide a greater share of the nation's health care. To achieve such a policy it can bring about change through positive regulation, or it can use the taxation regime, via tax expenditures, not to raise revenue but to steer or influence individuals in its desired direction. When used for this purpose, tax expenditures steer taxpayers towards or away from certain behaviour by either imposing costs on, or providing benefits to them. Within the context of the health sector, the Australian Federal Government deploys social steering via the tax system, with the Medicare Levy Surcharge and the 30 percent Private Health Insurance Rebate intended to steer taxpayer behaviour towards the Government’s policy goal of increasing the amount of health provision through the private sector. These steering mechanisms are complemented by the ‘Lifetime Health Cover Initiative’. This article, through the lens of behavioural economics, considers the ways in which these assorted mechanisms might have been expected to operate and whether they encourage individuals to purchase private health insurance.

Structural behaviour and design of cold-formed steel wall systems under fire conditions

In recent times, light gauge steel framed (LSF) structures, such as cold-formed steel wall systems, are increasingly used, but without a full understanding of their fire performance. Traditionally the fire resistance rating of these load-bearing LSF wall systems is based on approximate prescriptive methods developed based on limited fire tests. Very often they are limited to standard wall configurations used by the industry. Increased fire rating is provided simply by adding more plasterboards to these walls. This is not an acceptable situation as it not only inhibits innovation and structural and cost efficiencies but also casts doubt over the fire safety of these wall systems. Hence a detailed fire research study into the performance of LSF wall systems was undertaken using full scale fire tests and extensive numerical studies. A new composite wall panel developed at QUT was also considered in this study, where the insulation was used externally between the plasterboards on both sides of the steel wall frame instead of locating it in the cavity. Three full scale fire tests of LSF wall systems built using the new composite panel system were undertaken at a higher load ratio using a gas furnace designed to deliver heat in accordance with the standard time temperature curve in AS 1530.4 (SA, 2005). Fire tests included the measurements of load-deformation characteristics of LSF walls until failure as well as associated time-temperature measurements across the thickness and along the length of all the specimens. Tests of LSF walls under axial compression load have shown the improvement to their fire performance and fire resistance rating when the new composite panel was used. Hence this research recommends the use of the new composite panel system for cold-formed LSF walls. The numerical study was undertaken using a finite element program ABAQUS. The finite element analyses were conducted under both steady state and transient state conditions using the measured hot and cold flange temperature distributions from the fire tests. The elevated temperature reduction factors for mechanical properties were based on the equations proposed by Dolamune Kankanamge and Mahendran (2011). These finite element models were first validated by comparing their results with experimental test results from this study and Kolarkar (2010). The developed finite element models were able to predict the failure times within 5 minutes. The validated model was then used in a detailed numerical study into the strength of cold-formed thin-walled steel channels used in both the conventional and the new composite panel systems to increase the understanding of their behaviour under nonuniform elevated temperature conditions and to develop fire design rules. The measured time-temperature distributions obtained from the fire tests were used. Since the fire tests showed that the plasterboards provided sufficient lateral restraint until the failure of LSF wall panels, this assumption was also used in the analyses and was further validated by comparison with experimental results. Hence in this study of LSF wall studs, only the flexural buckling about the major axis and local buckling were considered. A new fire design method was proposed using AS/NZS 4600 (SA, 2005), NAS (AISI, 2007) and Eurocode 3 Part 1.3 (ECS, 2006). The importance of considering thermal bowing, magnified thermal bowing and neutral axis shift in the fire design was also investigated. A spread sheet based design tool was developed based on the above design codes to predict the failure load ratio versus time and temperature for varying LSF wall configurations including insulations. Idealised time-temperature profiles were developed based on the measured temperature values of the studs. This was used in a detailed numerical study to fully understand the structural behaviour of LSF wall panels. Appropriate equations were proposed to find the critical temperatures for different composite panels, varying in steel thickness, steel grade and screw spacing for any load ratio. Hence useful and simple design rules were proposed based on the current cold-formed steel structures and fire design standards, and their accuracy and advantages were discussed. The results were also used to validate the fire design rules developed based on AS/NZS 4600 (SA, 2005) and Eurocode Part 1.3 (ECS, 2006). This demonstrated the significant improvements to the design method when compared to the currently used prescriptive design methods for LSF wall systems under fire conditions. In summary, this research has developed comprehensive experimental and numerical thermal and structural performance data for both the conventional and the proposed new load bearing LSF wall systems under standard fire conditions. Finite element models were developed to predict the failure times of LSF walls accurately. Idealized hot flange temperature profiles were developed for non-insulated, cavity and externally insulated load bearing wall systems. Suitable fire design rules and spread sheet based design tools were developed based on the existing standards to predict the ultimate failure load, failure times and failure temperatures of LSF wall studs. Simplified equations were proposed to find the critical temperatures for varying wall panel configurations and load ratios. The results from this research are useful to both structural and fire engineers and researchers. Most importantly, this research has significantly improved the knowledge and understanding of cold-formed LSF loadbearing walls under standard fire conditions.

Antecedents of sustainable management support for IT related initiatives

Having IT-related capabilities is not enough to secure value from IT resources and survive in today’s competitive environment. IT resources evolve dynamically and firms must sustain their existing capabilities to continue to leverage value from their IT resources. Firm’s human resources are an important IT-related capability, and an important source of their competitive advantage. Using a field survey, this study demonstrates that a dynamic end-user environment, a result of a coordinated change in complementary factors can help sustain firms’ IT-related management capabilities. These factors include an appropriate organizational design to decision rights and work environment and a congruent reward system. This study adds an important dimension in understanding why some firms continue to perform better with their IT resources than others. For practice, this study suggests that a comprehensive approach to what constitutes valuable organizational resources is necessary.

A Context Space Model for Detecting Anomalous Behaviour in Video Surveillance

Having a good automatic anomalous human behaviour detection is one of the goals of smart surveillance systems’ domain of research. The automatic detection addresses several human factor issues underlying the existing surveillance systems. To create such a detection system, contextual information needs to be considered. This is because context is required in order to correctly understand human behaviour. Unfortunately, the use of contextual information is still limited in the automatic anomalous human behaviour detection approaches. This paper proposes a context space model which has two benefits: (a) It provides guidelines for the system designers to select information which can be used to describe context; (b)It enables a system to distinguish between different contexts. A comparative analysis is conducted between a context-based system which employs the proposed context space model and a system which is implemented based on one of the existing approaches. The comparison is applied on a scenario constructed using video clips from CAVIAR dataset. The results show that the context-based system outperforms the other system. This is because the context space model allows the system to considering knowledge learned from the relevant context only.

Models of collective cell behaviour with crowding effects : comparing lattice-based and lattice-free approaches

Individual-based models describing the migration and proliferation of a population of cells frequently restrict the cells to a predefined lattice. An implicit assumption of this type of lattice based model is that a proliferative population will always eventually fill the lattice. Here we develop a new lattice-free individual-based model that incorporates cell-to-cell crowding effects. We also derive approximate mean-field descriptions for the lattice-free model in two special cases motivated by commonly used experimental setups. Lattice-free simulation results are compared to these mean-field descriptions and to a corresponding lattice-based model. Data from a proliferation experiment is used to estimate the parameters for the new model, including the cell proliferation rate, showing that the model fits the data well. An important aspect of the lattice-free model is that the confluent cell density is not predefined, as with lattice-based models, but an emergent model property. As a consequence of the more realistic, irregular configuration of cells in the lattice-free model, the population growth rate is much slower at high cell densities and the population cannot reach the same confluent density as an equivalent lattice-based model.

The role of cultural beliefs in contributing to risky road use behaviour in Pakistan

Background Pakistan has the highest population rate of road fatalities in South Asia (25.3 fatalities per 100,000 people: Global Status Report on Road Safety, WHO 2009). Along with road environment and vehicle factors, human factors make a substantial contribution to traffic safety in Pakistan. Beliefs about road crash causation and prevention have been demonstrated to contribute to risky road use behaviour and resistance to preventive measures in a handful of other developing countries, but has not been explored in Pakistan. In particular, fatalism (whether based on religion, other cultural beliefs or experience) has been highlighted as a barrier to achieving changes in attitudes and behaviour. Aims The research reported here aimed (i) to explore perceptions of road crash causation among policy makers, police officers, professional drivers and car drivers in Pakistan; (ii) to identify how cultural and religious beliefs influence road use behaviour in Pakistan; and (iii) to understand how fatalistic beliefs may work as obstacles to road safety interventions. Methods In-depth interviews were conducted by the primary author (mostly in Urdu) in Lahore, Rawalpindi and Islamabad with 12 professional drivers (taxi, bus and truck), 4 car drivers, 6 police officers, 4 policy makers and 2 religious orators. All but two were Muslim, two were female, and they were drawn from a wide range of ages (24 to 60) and educational backgrounds. The interviews were taped and transcribed, then translated into English and analysed for themes related to the aims. Results Fatalism emerged as a pervasive belief utilised to justify risky road use behaviour and to resist messages about preventive measures. There was a strong religious underpinning to the statement of fatalistic beliefs (this reflects popular conceptions of Islam rather than scholarly interpretations), but also an overlap with superstitious beliefs which have longer-standing roots in Pakistani culture. These beliefs were not limited to people of poor educational background or position. A particular issue which was explored in more detail was the way in which these beliefs and their interpretation within Pakistani society contributed to poor police reporting of crashes. Discussion and conclusions The pervasive nature of fatalistic beliefs in Pakistan affects road user behaviour by supporting continued risk taking behaviour on the road, and by interfering with public health messages about behaviours which would reduce the risk of traffic crashes. The widespread influence of these beliefs on the ways that people respond to traffic crashes and the death of family members contribute to low crash reporting rates and to a system which is difficult to change. The promotion of an evidence-based approach to road user behaviour is recommended, along with improved professional education for police and policy makers.

One more tier, no more tears: Students’ perceptions of QUT Library’s 2nd tier learning and study support

This nuts and bolts session discusses QUT Library’s Study Solutions service which is staffed by academic skills advisors and librarians as the 2nd tier of its learning and study support model. Firstly, it will discuss the rationale behind the Study Solutions model and provide a brief profile of the service. Secondly, it will outline what distinguishes it from other modes of one-to-one learning support. Thirdly, it will report findings from a student perception study conducted to determine what difference this model of individual study assistance made to academic confidence, ability to transfer academic skills and capacity to assist peers. Finally, this session will include small group discussions to consider the feasibility of this model as best practice for other tertiary institutions and student perception as a valuable measure of the impact of learning support services.