VLC oriented energy efficient driver techniques

LEDs are substituting fluorescent and incandescent bulbs as illumination sources due to their low power consumption and long lifetime. Visible Light Communications (VLC) makes use of the LEDs short switching times to transmit information. Although LEDs switching speed is around Mbps range, higher speeds (hundred of Mbps) can be reached by using high bandwidth-efficiency modulation techniques. However, the use of these techniques requires a more complex driver which elevates drastically its power consumption. In this work an energy efficiency analysis of the different VLC modulation techniques and drivers is presented. Besides, the design of new schemes of VLC drivers is described.

Single - and double energy swift and slow heavy ion irradiated optical waveguides in Er: Tungstene-Tellurite glass and BGO for telecom applications

The fabrication of broadband amplifiers in wavelength division multiplexing (WDM) around 1.55 m, as they exhibit large stimulated cross sections and broad emission bandwidth. Bi4Ge3O12 (eultine type BGO) - well known scintillator material, also a rare-earth host material, photorefractive waveguides produced in it only using light ions in the past. Recently: MeV N+ ions and swift O5+ and C5+ ions, too*. Bi12GeO20 (sillenite type BGO) - high photoconductivity and photorefractive sensitivity in the visible and NIR good candidate for real-time holography and optical phase conjugation, photorefractive waveguides produced in it only using light ions. No previous attempts of ion beam fabrication of waveguides in it.

Evaluación de protocolos de encaminamiento en una red inalámbrica mallada desplegada en una zona rural

The implementation of wireless communication systems in rural areas through the deployment of data networks in infrastructure mode is often inadequate due to its high cost and no fault tolerant centralized structure. Mesh networks can overcome these limitations while increases the coverage area in a more flexible way. This paper proposes the performance evaluation of the routing protocols IEEE 802.11s and Batman-Adv on an experimental wireless mesh network deployed in a rural environment called Lachocc, which is a community located at 4700 MASL in the Huancavelica region in Peru. The evaluation was based on the measurement of quality of service parameters such as bandwidth, delay and delay variation. As a result, it was determined that both protocols offer a good performance, but in most of the cases, Batman-Adv provides slightly better performance

Analog mitigation of out of band strong interferers in wide band acquisition for multiband HF transmissions

It is clear that in the near future much broader transmissions in the HF band will replace part of the current narrow band links. Our personal view is that a real wide band signal is infeasible in this environment because the usage is typically very intensive and may suffer interferences from all over the world. Therefore, we envision that dynamic multiband transmissions may provide better satisfactory performance. From the very beginning, we observed that real links with our broadband transceiver suffered interferences out of our multiband but within the acquisition bandwidth that degrade the expected performance. Therefore, we concluded that a mitigation structure is required that operates on severely saturated signals as the interference may be of much higher power. In this paper we address a procedure based on Higher Order Crossings (HOC) statistics that are able to extract most of the signal structure in the case where the amplitude is severely distorted and allows the estimation of the interference carrier frequency to command a variable notch filter that mitigates its effect in the analog domain.

Synchronous Buck converter with Output Impedance Correction Circuit

This work is related to the improvement of the output impedance of the Buck converter by means of introducing an additional power path that virtually increases the output capacitance during transients. It is well known that in VRM applications, with wide load steps, voltage overshoots and undershoots may lead to undesired performance of the load. To solve this problem, high-bandwidth high-switching frequency power converters can be applied to reduce the transient time or a big output capacitor can be applied to reduce the output impedance. The first solution can degrade the efficiency by increasing switching losses of the MOSFETS, and the second solution is penalizing the cost and size of the output filter. The Output Impedance Correction Circuit (OICC), as presented here, is used to inject or extract a current n-1 times larger than the output capacitor current, thus virtually increasing n times the value of the output capacitance during the transients. This feature allows the usage of a low frequency Buck converter with smaller capacitor but satisfying the dynamic requirements.

Sensorless explicit model predictive control for multi-phase buck converters with variable output voltage

The purpose of this paper is to use the predictive control to take advantage of the future information in order to improve the reference tracking. The control attempts to increase the bandwidth of the conventional regulators by using the future information of the reference, which is supposed to be known in advance. A method for designing a controller is also proposed. A comparison in simulation with a conventional regulator is made controlling a four-phase Buck converter. Advantages and disadvantages are analyzed based on simulation results.

Power management techniques in an FPGA-Based WSN node for high performance application

In this work, the power management techniques implemented in a high-performance node for Wireless Sensor Networks (WSN) based on a RAM-based FPGA are presented. This new node custom architecture is intended for high-end WSN applications that include complex sensor management like video cameras, high compute demanding tasks such as image encoding or robust encryption, and/or higher data bandwidth needs. In the case of these complex processing tasks, yet maintaining low power design requirements, it can be shown that the combination of different techniques such as extensive HW algorithm mapping, smart management of power islands to selectively switch on and off components, smart and low-energy partial reconfiguration, an adequate set of save energy modes and wake up options, all combined, may yield energy results that may compete and improve energy usage of typical low power microcontrollers used in many WSN node architectures. Actually, results show that higher complexity tasks are in favor of HW based platforms, while the flexibility achieved by dynamic and partial reconfiguration techniques could be comparable to SW based solutions.

Optimal Design of Envelope Amplifier Based on Linear Assisted Buck Converter

Envelope Tracking (ET) and Envelope Elimination and Restoration (EER) are two techniques that have been used as a solution for highly efficient linear RF Power Amplifiers (PA). In both techniques the most important part is a dc-dc converter called envelope amplifier that has to supply the RF PA with variable voltage. Besides high efficiency, its bandwidth is very important as well. Envelope amplifier based on parallel combination of a switching dc-dc converter and a linear regulator is an architecture that is widely used due to its simplicity. In this paper we discuss about theoretical limitations of this architecture regarding its efficiency and we demonstrate two possible way of its implementation. In order to derive the presented conclusions, a theoretical model of envelope amplifier's efficiency has been presented. Additionally, the benefits of the new emerging GaN technology for this application have been shown as well.

Improvement of the Dynamic Performance of a Buck Converter using Controlled Current Source as an Additional Energy Path

This work is related to the improvement of the dynamic performance of the Buck converter by means of introducing an additional power path that virtually increase s the output capacitance during transients, thus improving the output impedance of the converter. It is well known that in VRM applications, with wide load steps, voltage overshoots and undershoots ma y lead to undesired performance of the load. To solve this problem, high-bandwidth high-switching frequency power converter s can be applied to reduce the transient time or a big output capacitor can be applied to reduce the output impedance. The first solution can degrade the efficiency by increasing switching losses of the MOSFETS, and the second solution is penalizing the cost and size of the output filter. The additional energy path, as presented here, is introduced with the Output Impedance Correction Circuit (OICC) based on the Controlled Current Source (CCS). The OICC is using CCS to inject or extract a current n - 1 times larger than the output capacitor current, thus virtually increasing n times the value of the output capacitance during the transients. This feature allows the usage of a low frequency Buck converter with smaller capacitor but satisfying the dynamic requirements.

High Efficiency Envelope Amplifier Using The Slow-Envelope Technique

High efficiency envelope amplifiers are demanded in EER technique for RF transmitters, which benefits low maintaining cost or long battery time. The conventional solution is a dc-dc switching converters. This dc-dc converter should operate at very high frequency to track an envelope in the MHz range to supply the power amplifier. One of the alternative circuits suitable for this application is a hybrid topology composed of a switched converter and a linear regulator in series that work together to adjust the output voltage to track the envelope with accuracy. This topology can take advantage of the reduced slew-rate technique (also called slow-envelope technique) where switching dc-dc converter provides the RF envelope with limited slew rate in order to avoid high switching frequency and high power losses, while the linear regulator performs fine adjustment in order to obtain the exact replica of the RF envelope. The combination of this control technique with this topology is proposed in this paper. Envelopes with different bandwidth will be considered to optimize the efficiency of the dc-dc converter.

Envelope Amplifier Based on a Hybrid Series Converter With The Slow-envelope Technique

High frequency dc-dc switching converters are used as envelope amplifiers in RF transmitters. The dc-dc converter should operate at very high frequency to track an envelope in the MHz range to supply the power amplifier. One of the circuits suitable for this application is a hybrid topology composed of a switched converter and a linear regulator in series that work together to adjust the output voltage to track the envelope with accuracy. This topology can take advantage of the reduced slew-rate technique where switching dc-dc converter provides the RF envelope with limited slew rate in order to avoid high switching frequency and high power losses, while the linear regulator performs fine adjustment in order to obtain the exact replica of the RF envelope. The combination of this control technique with this topology is proposed in this paper. Envelopes with different bandwidth will be considered to optimize the efficiency of the dc-dc converter. The calculations and experiments have been done to track a 2MHz envelope in the range 0-12V for an EER RF transmitter.

Comparison of V2IC control with voltage mode and current mode controls for high frequency (MHz) and very fast response applications

High switching frequencies (several MHz) allow the integration of low power DC/DC converters. Although, in theory, a high switching frequency would make possible to implement a conventional Voltage Mode control (VMC) or Peak Current Mode control (PCMC) with very high bandwidth, in practice, parasitic effects and robustness limits the applicability of these control techniques. This paper compares VMC and CMC techniques with the V2IC control. This control is based on two loops. The fast internal loop has information of the output capacitor current and the error voltage, providing fast dynamic response under load and voltage reference steps, while the slow external voltage loop provides accurate steady state regulation. This paper shows the fast dynamic response of the V2IC control under load and output voltage reference steps and its robustness operating with additional output capacitors added by the customer.

An overview of fast DC-DC converters for envelope amplifier in RF transmitters

In the last years, RF power amplifiers are taking advantage of the switched dc-dc converters to use them in several architectures that may improve the efficiency of the amplifier, keeping a good linearity. The use of linearization techniques such as Envelope Elimination and Restoration (EER) and Envelope Tracking (ET) requires a very fast dc-dc power converter to provide variable voltage supply to the power amplifier but theoretically the efficiency can be much higher than using the classical amplifiers belonging to classes A, B or AB. The purpose of this paper is to analyze the state of the art of the power converters used as envelope amplifiers in this application where a fast output voltage variation is required. The power topologies will be explored and several important parameters such as efficiency, bandwidth and output voltage range will be discussed.

Estudio de redes WSN y su aplicación a la ingeniería civil

Las redes inalámbricas están experimentando un gran crecimiento en el campo de la instrumentación electrónica. En concreto las redes de sensores inalámbricas (WSN de Wireless Sensor Network) suponen la opción más ventajosa para su empleo en la instrumentación electrónica ya que sus principales características se acoplan perfectamente a las necesidades. Las WSN permiten la utilización de un número relativamente alto de nodos, están orientadas a sistemas de bajo consumo y funcionamiento con baterías y poseen un ancho de banda adecuado para las necesidades de la instrumentación electrónica. En este proyecto fin de carrera se ha realizado un estudio de las tecnologías inalámbricas disponibles, se han comparado y se ha elegido la tecnología ZigBeeTM por considerarse la más adecuada y la que más se ajusta a las necesidades descritas. En el desarrollo de mi vida profesional se han conectado dos campos teóricamente distantes como son la instrumentación electrónica y la ingeniería civil. En este proyecto se hace una descripción de la instrumentación que se utiliza para controlar estructuras como presas, túneles y puentes y se proponen casos prácticos en los que las redes WSN aportan valor añadido a instrumentación actual y a los sistemas de comunicaciones utilizados. Se definen tanto los sistemas de comunicaciones utilizados actualmente como una serie de sensores utilizados para medir los principales parámetros a controlar en una obra civil. Por último se ha desarrollado una aplicación de prueba de una red ZigBeeTM basada en equipos comerciales del fabricante Digi. consiste en una aplicación desarrollada en entorno web que maneja de forma remota, a través de Internet, las entradas y salidas digitales y analógicas de los nodos que forman la red. Se forma una red ZigBeeTM con un coordinador, un router y un dispositivo final. El Coordinador está integrado en un Gateway que permite acceder a la red ZigBeeTM a través de internet y conocer el estado de los nodos que forman la red. Con los comandos adecuados se puede leer el estado de las entradas y salidas analógicas y digitales y cambiar el estado de una salida digital. ABSTRACT. Wireless networks are experiencing tremendous growth in the field of electronic instrumentation. In particular wireless sensor networks represent the most advantageous for use in electronic instrumentation since its main characteristics fit perfectly to the needs. The WSN allow the use of a relatively large number of nodes, are aimed at low-power systems and battery operation and have an adequate bandwidth for the needs of electronic instrumentation. In this project has made a study of available wireless technologies have been compared and chosen ZigBeeTM technology was considered the most appropriate to the needs described. In the course of my professional life have connected two fields are theoretically distant as electronic instrumentation and civil engineering. In this project, there is a description of the instrumentation used to control structures such as dams, tunnels and bridges and proposes practical cases in which WSN networks add value to current instrumentation and communications systems used. There are defined as communications systems now being used as a set of sensors used to measure the main parameters to be controlled in a civil structure. Finally, I have developed a test application based ZigBeeTM networking equipment maker Digi trading. It consists of a Web-based application developed to manage remotely, via the Internet, the digital and analog inputs and outputs nodes forming the network. ZigBeeTM It forms a network with a coordinator, router and end device. The Coordinator is built into a gateway that allows access to the ZigBeeTM network through internet and know the status of the nodes forming the network. With the appropriate command can read the status of the digital inputs and outputs and change the state of a digital output.

Hogar digital para servicios FTTH : dispositivos, tecnologías y QoE

FTTH (fibra hasta el hogar) es actualmente, junto con la banda ancha móvil, la principal evolución tecnológica en Redes y Servicios de Telecomunicaciones. Se prevé que en los próximos años, el despliegue de las redes FTTH se vea incrementado de manera significativa, gracias al interés creciente tanto de Operadores de Telecomunicaciones como de Organismos Gubernamentales. Este despliegue (que en el año 2013 ya se está haciendo realidad) llevará servicios de muy alta velocidad (superiores a 100 Mbps, incluso 1 Gbps) de manera masiva a los hogares, exigiendo nuevos requisitos y prestaciones en la red del hogar de los clientes. Se abre aquí, por tanto, un campo de exploración novedoso, incipiente y de requerimientos cada vez más exigentes. De hecho, sin duda, la red del hogar es uno de los elementos fundamentales para el éxito de las redes y servicios en FTTH. Debido a todo lo anterior, se convierte en una necesidad para el sector de las Telecomunicaciones el encontrar soluciones a los problemas anteriormente mencionados. Con objeto de contribuir al análisis de soluciones, este proyecto se enfoca en dos temas, ambos relacionados con la problemática ya mencionada en la red del hogar:  Prospección e identificación de soluciones tecnológicas avanzadas para la red del hogar. Descrito en capítulos 2, 3 y 4. En ellos se realiza un estudio detallado de la situación actual y tendencias futuras de los dispositivos utilizados en la red del hogar. Este estudio está enfocado en la distribución de señales de muy alto ancho de banda (en torno a los 100 Mbps por segundo) en el hogar.  Diseño y desarrollo de una aplicación que permita determinar la calidad de experiencia de cliente (QoE) de un servicio de televisión IP (IPTV). Descrito en capítulos 5 y 6. Se ha seleccionado este tipo de servicios debido a que son los que requieren mayores prestaciones tanto de la red de transporte como de la red del hogar y, al mismo tiempo, son los más complicados de medir debido a la fuerte componente de subjetividad del usuario final. Una red del hogar correctamente diseñada debe cumplir de manera equilibrada los requisitos demandados tanto por el operador como por el cliente o usuario final del servicio. Los requisitos del operador se centran principalmente en el control de la inversión (CAPEX) y del gasto de mantenimiento de la red del hogar (OPEX). El usuario, por otra parte, requiere sencillez en la instalación y mínimo número de elementos a instalar (cero intrusismo, ausencia de cableado). Para adaptarse a estos requerimientos, existe una serie de dispositivos y tecnologías que buscan encontrar el punto de equilibrio entre necesidades de operadores y de clientes finales. Las soluciones actualmente utilizadas pueden dividirse en soluciones cableadas e inalámbricas. También existen soluciones híbridas. Todas ellas se describen en detalle en los capítulos 3 y 4. Al final del estudio se concluye que, con la tecnología actual, es preferible el uso de soluciones cableadas tipo Ethernet o POF. Es recomendable no usar soluciones PLC de manera extensiva (G.hn puede ser una alternativa a futuro) y, en caso de no requerir cableado, utilizar WiFi 11n con frecuencias de 5 GHz, así como sus evoluciones, WiFi 11ac y 11ad. La aplicación desarrollada, explicada en los capítulos 5 y 6, permite capturar y medir en tiempo real la señal de televisión IP que se entrega al usuario. Esta aplicación estimará, a partir de dichas medidas, la calidad de la señal entregada. Para ello tendrá en cuenta el tipo de descodificador utilizado por el usuario así como la red empleada (red FTTH de Telefónica). Esta aplicación podría ser utilizada en los centros de atención técnica de las operadoras de telecomunicaciones, determinando así la relación existente entre reclamaciones recibidas y calidad de servicio medida por la aplicación. Asimismo, aparte de realizar medidas en tiempo real, la aplicación vuelca las medidas realizadas y alarmas detectadas en ficheros log, facilitando el análisis técnico de los problemas e incidencias registrados por dichos centros técnicos. Igualmente, esta aplicación puede ser utilizada para el proceso de certificación de equipamiento de red del hogar o incluso como herramienta para profundizar en parámetros teóricos y criterios de medida de calidad de servicio en IPTV. ABSTRACT. FTTH (Fiber To The Home) and mobile broadband are currently the main technological trend in the Network and Telecommunications Services area. In the next few years, the deployment of FTTH networks will experiment a significant increase, due to the growing interest of both telecommunications operators and government agencies. This deployment (that is becoming a reality) which will massively carry high-speed services to households (speeds of more than 100 Mbps, even 1 Gbps) will demand new requirements and features in the customer’s home network. It can be found here a new and emerging field of exploration, with increasingly demanding requirements. In fact, the home network is one of the key elements for the success of FTTH network and services. Due to the aforementioned, it is a necessity for the telecommunications industry to find solutions to these problems. In order to contribute into the solution analysis, this project focuses on two subjects, both related to the problems of home networking:  Exploratory research and identification of advanced technology solutions for the home network. Described in chapters 2, 3 and 4. These chapters show a detailed study of the current situation and future trends of the devices used at the home network. It focuses on the distribution of very high bandwidth signals (around 100 Mbps per second) in the customer’s home.  Design and development of an application to evaluate customer’s quality of experience (QoE) of an IP television service (IPTV). Described in chapters 5 and 6. IPTV service has been selected because it requires higher performance both from the transport and the home networks and, at the same time, it is the most difficult to measure due to the strong component of subjectivity of the end user. A correct design of the home network must meet the requirements demanded both by the network operator and the customer (end user of the service). Network operator requirements mainly focus on reduced capital expenditures (CAPEX) and operational expenditures (OPEX). Additionally, the final user requires a simple and easy installation and also the minimum number of items to install (zero intrusion, lack of wiring, etc.). Different devices and technologies seek to find a balance between these two requirements (network operators and final users requirements). Solutions available in the market can be divided into wired and wireless. There are also hybrid solutions. All of them are described thoroughly in the first part of the project. The conclusion at the end of the study recommends the use of wired technologies like Ethernet or POF. Additionally, the use of PLC is not advised (G.hn can be an alternative in the future) and, in the case of not requiring wiring, the use of 11ac and 11ad WiFi is advised. The application developed in the second part of the project allows capturing and measuring the real-time IPTV signal delivered to the user. This application will estimate the delivered signal quality from the captured measurements. For this purpose, it will also consider the type of decoder installed on the customer’s premises and the transport network (Telefonica’s FTTH network). This application could be used at the operator’s technical service centres, determining in this way the relationship between user’s complaints and the quality of service measured. Additionally, this application can write all the measurements and alarms in log files, making easier the technical analysis of problems and impairments recorded by the technical centres. Finally, the application can also be used for the certification process of home networking equipment (i.e. decoders) or even as a tool to deepen theoretical parameters and measuring criteria of quality of service in IPTV.