Vertical fluxes of sediment in oscillatory sheet flow

Time series of vertical sediment fluxes are derived from concentration time series in sheet flow under waves. While the concentrations C(z,t) vary very little with time for \z\ < 10d(50), the measured vertical sediment fluxes Q(zs)(z,t) vary strongly with time in this vertical band and their time variation follows, to some extent, the variation of the grain roughness Shields parameter 02,5(t). Thus, sediment distribution models based on the pickup function boundary condition are in some qualitative agreement with the measurements. However, the pickup function models are only able to model the upward bursts of sediment during the accelerating phases of the flow. They are, so far, unable to model the following strong downward sediment fluxes, which are observed during the periods of flow deceleration. Classical pickup functions, which essentially depend on the Shields parameter, are also incapable of modelling the secondary entrainment fluxes, which sometimes occur at free stream velocity reversal. The measured vertical fluxes indicate that the effective sediment settling velocity in the high [(0.3 < C(z,t) < 0.4] concentration area is typically only a few percent of the clear water settling velocity, while the measurements of Richardson and Jeronimo [Chem. Eng. Sci. 34 (1979) 1419], from a different physical setting, lead to estimates of the order 20%. The data does not support gradient diffusion as a model for sediment entrainment from the bed. That is, detailed modelling of the observed near-bed fluxes would require diffusivities that go negative during periods of flow deceleration. An observed general trend for concentration variability to increase with elevation close to the bed is also irreconcilable with diffusion models driven by a bottom boundary condition. (C) 2002 Published by Elsevier Science B.V.

Numerical investigations of flow and energy fields near a thermoacoustic couple

The flow field and the energy transport near thermoacoustic couples are simulated using a 2D full Navier-Stokes solver. The thermoacoustic couple plate is maintained at a constant temperature; plate lengths, which are short and long compared with the particle displacement lengths of the acoustic standing waves, are tested. Also investigated are the effects of plate spacing and the amplitude of the standing wave. Results are examined in the form of energy vectors, particle paths, and overall entropy generation rates. These show that a net heat-pumping effect appears only near the edges of thermoacoustic couple plates, within about a particle displacement distance from the ends. A heat-pumping effect can be seen even on the shortest plates tested when the plate spacing exceeds the thermal penetration depth. It is observed that energy dissipation near the plate increases quadratically as the plate spacing is reduced. The results also indicate that there may be a larger scale vortical motion outside the plates which disappears as the plate spacing is reduced. (C) 2002 Acoustical Society of America.

Beware the boogie board: blunt abdominal trauma from bodyboarding

Riding waves on a bodyboard (boogie board) at the beach is popular with children. Three teenagers who sustained blunt abdominal trauma during bodyboarding are described. Two suffered lacerated livers, one a lacerated spleen. Serious blunt abdominal injuries from bodyboarding mishaps have not previously been reported. The usual method of riding a bodyboard may place the rider at risk of abdominal trauma.

Critical comparison of Julius Kruttschnitt Mineral Research Centre (JKMRC) blast fragmentation models

Blast fragmentation can have a significant impact on the profitability of a mine. An optimum run of mine (ROM) size distribution is required to maximise the performance of downstream processes. If this fragmentation size distribution can be modelled and controlled, the operation will have made a significant advancement towards improving its performance. Blast fragmentation modelling is an important step in Mine to Mill™ optimisation. It allows the estimation of blast fragmentation distributions for a number of different rock mass, blast geometry, and explosive parameters. These distributions can then be modelled in downstream mining and milling processes to determine the optimum blast design. When a blast hole is detonated rock breakage occurs in two different stress regions - compressive and tensile. In the-first region, compressive stress waves form a 'crushed zone' directly adjacent to the blast hole. The second region, termed the 'cracked zone', occurs outside the crush one. The widely used Kuz-Ram model does not recognise these two blast regions. In the Kuz-Ram model the mean fragment size from the blast is approximated and is then used to estimate the remaining size distribution. Experience has shown that this model predicts the coarse end reasonably accurately, but it can significantly underestimate the amount of fines generated. As part of the Australian Mineral Industries Research Association (AMIRA) P483A Mine to Mill™ project, the Two-Component Model (TCM) and Crush Zone Model (CZM), developed by the Julius Kruttschnitt Mineral Research Centre (JKMRC), were compared and evaluated to measured ROM fragmentation distributions. An important criteria for this comparison was the variation of model results from measured ROM in the-fine to intermediate section (1-100 mm) of the fragmentation curve. This region of the distribution is important for Mine to Mill™ optimisation. The comparison of modelled and Split ROM fragmentation distributions has been conducted in harder ores (UCS greater than 80 MPa). Further work involves modelling softer ores. The comparisons will be continued with future site surveys to increase confidence in the comparison of the CZM and TCM to Split results. Stochastic fragmentation modelling will then be conducted to take into account variation of input parameters. A window of possible fragmentation distributions can be compared to those obtained by Split . Following this work, an improved fragmentation model will be developed in response to these findings.

Combining nonthermal technologies to control foodborne microorganisms

Novel nonthermal processes, such as high hydrostatic pressure (HHP), pulsed electric fields (PEFs), ionizing radiation and ultrasonication, are able to inactivate microorganisms at ambient or sublethal temperatures. Many of these processes require very high treatment intensities, however, to achieve adequate microbial destruction in low-acid foods. Combining nonthermal processes with conventional preservation methods enhances their antimicrobial effect so that lower process intensities can be used. Combining two or more nonthermal processes can also enhance microbial inactivation and allow the use of lower individual treatment intensities. For conventional preservation treatments, optimal microbial control is achieved through the hurdle concept, with synergistic effects resulting from different components of the microbial cell being targeted simultaneously. The mechanisms of inactivation by nonthermal processes are still unclear; thus, the bases of synergistic combinations remain speculative. This paper reviews literature on the antimicrobial efficiencies of nonthermal processes combined with conventional and novel nonthermal technologies. Where possible, the proposed mechanisms of synergy is mentioned. (C) 2003 Elsevier Science B.V. All rights reserved.

The application of wave induced forces to a two-dimensional finite element long wave hydrodynamic model

This paper describes the modification of a two-dimensional finite element long wave hydrodynamic model in order to predict the net current and water levels attributable to the influences of waves. Tests examine the effects of the application of wave induced forces, including comparisons to a physical experiment. An example of a real river system is presented with comparisons to measured data, which demonstrate the importance of simulating the combined effects of tides and waves upon hydrodynamic behavior. (C) 2002 Elsevier Science Ltd. All rights reserved.

Occurrence of storm-generated bedforms along the inner continental shelf - Southeastern Brazil

Levantamentos sonográficos desenvolvidos em duas áreas da plataforma interna adjacente ao estado do Espírito Santo revelam formas de fundo cuja origem é fortemente relacionada a eventos de tempestades. Estas são caracterizadas por alternâncias de bandas de areias finas sobrepostas, de forma alternada, a um fundo de areias grossas, gerando manchas de areias grossas intercaladas abruptamente com faixas de areias finas a profundidades de 25-30 m para GUA e de 05-08 m para BES. Em ambas as áreas as faixas de areias grossas apresentam marcas de ondulação geradas por ondas com orientação levemente paralela a linha de costa. A sedimentologia de GUA é composta por areias finas a muito finas lamosas carbonáticas com cascalhos siliciclásticos e a de BES por areias grossas e médias com cascalhos biodetríticos. Desta forma, é clara a ação de correntes/ondas de tempestade no fundo marinho de GUA e de BES; porém, a classificação quanto ao comportamento hidrodinâmico e ao transporte de sedimento é necessária para as estimativas sobre a formação, transporte e manutenção das feições encontradas.

Modelo de escoamento multifásico para estudo da interação onda/sedimento

Modelos de escoamento multifásico são amplamente usados em diversas áreas de pesquisa ambiental, como leitos fluidizados, dispersão de gás em líquidos e vários outros processos que englobam mais de uma propriedade físico-química do meio. Dessa forma, um modelo multifásico foi desenvolvido e adaptado para o estudo do transporte de sedimentos de fundo devido à ação de ondas de gravidade. Neste trabalho, foi elaborado o acoplamento multifásico de um modelo euleriano não-linear de ondas do tipo Boussinesq, baseado na formulação numérica encontrada em Wei et al. (1995), com um modelo lagrangiano de partículas, fundamentado pelo princípio Newtoniano do movimento com o esquema de colisões do tipo esferas rígidas. O modelo de ondas foi testado quanto à sua fonte geradora, representada por uma função gaussiana, pá-pistão e pá-batedor, e quanto à sua interação com a profundidade, através da não-linearidade e de propriedades dispersivas. Nos testes realizados da fonte geradora, foi observado que a fonte gaussiana, conforme Wei et al. (1999), apresentou melhor consistência e estabilidade na geração das ondas, quando comparada à teoria linear para um kh   . A não-linearidade do modelo de ondas de 2ª ordem para a dispersão apresentou resultados satisfatórios quando confrontados com o experimento de ondas sobre um obstáculo trapezoidal, onde a deformação da onda sobre a estrutura submersa está em concordância com os dados experimentais encontrados na literatura. A partir daí, o modelo granular também foi testado em dois experimentos. O primeiro simula uma quebra de barragem em um tanque contendo água e o segundo, a quebra de barragem é simulada com um obstáculo rígido adicionado ao centro do tanque. Nesses experimentos, o algoritmo de colisão foi eficaz no tratamento da interação entre partícula-partícula e partícula-parede, permitindo a evidência de processos físicos que são complicados de serem simulados por modelos de malhas regulares. Para o acoplamento do modelo de ondas e de sedimentos, o algoritmo foi testado com base de dados da literatura quanto à morfologia do leito. Os resultados foram confrontados com dados analíticos e de modelos numéricos, e se mostraram satisfatórios com relação aos pontos de erosão, de sedimentação e na alteração da forma da barra arenosa

Sistema de accionamento de pás móveis para turbina de impulso

A actual dependência mundial dos combustíveis fósseis e a crescente necessidade de redução do seu consumo têm culminado em novas directrizes de gestão de recursos de energia. A utilização de recursos energéticos renováveis apresenta-se como um caminho vital para o desenvolvimento sustentável da nossa sociedade. Assim sendo, a energia das ondas surge como potencial fonte de energia que muitos autores afirmam como sendo um dos sectores com maior potencial energético por metro quadrado de área. Contudo, esta ainda é uma tecnologia muito recente, que ainda evidencia uma grande diversidade de conceitos e que ainda se encontra numa fase inicial de demonstração. É neste contexto que foi criado o projecto CORES que visa desenvolver uma turbina de impulso com pás guia de posição variável, no âmbito do desenvolvimento de novos dispositivos e componentes para produção de energia através das ondas do mar. Neste trabalho será desenvolvido um sistema de accionamento de pás móveis para a turbina de impulso, tendo como principal objectivo o fabrico de um protótipo. Assim sendo, será realizado o desenvolvimento, dimensionamento e análise dos seus elementos móveis, bem como do sistema de actuação que melhor se adeqúe e permita um correcto funcionamento do conjunto.

A energia das ondas e o seu aproveitamento

As crises energéticas surgidas no decorrer do último século, incluindo a crise do petróleo, obrigaram o Homem a procurar cada vez mais fontes de energia alternativas e preferencialmente inesgotáveis. Desta situação, resultou uma forte aposta na exploração das fontes de energias renováveis, que são uma das principais alternativas para responder a um aumento de procura, e também, face às exigências de consumos actuais, beneficiando de ao se apostar numa energia limpa e renovável existir uma forte redução nos impactes ambientais que outras fontes de energia não apresentam. O aproveitamento dos recursos provenientes de fontes de energia renováveis para a produção de energia já existe há vários anos, e, em alguns casos, atingiram já um estado de maturidade considerável, como é caso da energia eólica. Em comparação, o mesmo já não acontece com a energia das ondas. Embora o oceano apresente um recurso com enorme potencial para ser explorado, incluindo as ondas e correntes oceânicas, os dispositivos tecnológicos necessários para a exploração deste recurso encontram-se maioritariamente ainda em fase experimental, havendo casos pontuais que atingiram a fase pré-comercial. Assim, não existe até à data um dispositivo padrão para a exploração da energia das ondas em grande escala, contrariamente ao que acontece com a energia eólica. Para esta situação, contribuiu o elevado número de dispositivos patenteados para a exploração da energia das ondas, nenhum deles com vantagens significativas relativamente a outros, e também, devido ao facto de a exploração deste tipo de energia não poder ser feito de igual modo na costa ou a muitos quilómetros dela. Na presente dissertação são apresentados alguns dos principais dispositivos existentes para a extracção de energia proveniente das ondas oceânicas, com especial atenção para os dispositivos de coluna de água oscilante.

Two-year follow-up study of elderly residents in S. Paulo, Brazil: methodology and preliminary results

INTRODUCTION: Previous cross-sectional studies have shown a high prevalence of chronic disease and disability among the elderly. Given Brazil’s rapid aging process and the obvious consequences of the growing number of old people with chronic diseases and associated disabilities for the provision of health services, a need was felt for a study that would overcome the limitations of cross-sectional data and shed some light on the main factors determining whether a person will live longer and free of disabling diseases, the so-called successful aging. The methodology of the first follow-up study of elderly residents in Brazil is presented. METHOD: The profile of the initial cohort is compared with previous cross-sectional data and an in-depth analysis of nonresponse is carried out in order to assess the validity of future longitudinal analysis. The EPIDOSO (‘Epidemiologia do Idoso’) Study conducted a two-year follow-up of 1,667 elderly people (65+), living in S. Paulo. The study consisted of two waves, each consisting of household, clinical, and biochemical surveys. RESULTS AND CONCLUSIONS: In general, the initial cohort showed a similar profile to previous cross-sectional samples in S. Paulo. There was a majority of women, mostly widows, living in multigenerational households, and a high prevalence of chronic illnesses, psychiatric disturbances, and physical disabilities. Despite all the difficulties inherent in follow-up studies, there was a fairly low rate of nonresponse to the household survey after two years, which did not actually affect the representation of the cohort at the final household assessment, making unbiased longitudinal analysis possible. Concerning the clinical and blood sampling surveys, the respondents tended to be younger and less disabled than the nonrespondents, limiting the use of the clinical and laboratory data to longitudinal analysis aimed at a healthier cohort. It is worth mentioning that gender, education, family support, and socioeconomic status were not important determinants of nonresponse, as is often the case.

Stratification of the earth beneath the Azores from P and S receiver functions

Seismic recordings of IRIS/IDA/GSN station CMLA and of several temporary stations in the Azores archipelago are processed with P and S receiver function (PRF and SRF) techniques. Contrary to regional seismic tomography these methods provide estimates of the absolute velocities and of the Vp/Vs ratio up to a depth of similar to 300 km. Joint inversion of PRFs and SRFs for a few data sets consistently reveals a division of the subsurface medium into four zones with a distinctly different Vp/Vs ratio: the crust similar to 20 km thick with a ratio of similar to 1.9 in the lower crust, the high-Vs mantle lid with a strongly reduced VpNs velocity ratio relative to the standard 1.8, the low-velocity zone (LVZ) with a velocity ratio of similar to 2.0, and the underlying upper-mantle layer with a standard velocity ratio. Our estimates of crustal thickness greatly exceed previous estimates (similar to 10 km). The base of the high-Vs lid (the Gutenberg discontinuity) is at a depth of-SO km. The LVZ with a reduction of S velocity of similar to 15% relative to the standard (IASP91) model is terminated at a depth of similar to 200 km. The average thickness of the mantle transition zone (TZ) is evaluated from the time difference between the S410p and SKS660p, seismic phases that are robustly detected in the S and SKS receiver functions. This thickness is practically similar to the standard IASP91 value of 250 km. and is characteristic of a large region of the North Atlantic outside the Azores plateau. Our data are indicative of a reduction of the S-wave velocity of several percent relative to the standard velocity in a depth interval from 460 to 500 km. This reduction is found in the nearest vicinities of the Azores, in the region sampled by the PRFs, but, as evidenced by SRFs, it is missing at a distance of a few hundred kilometers from the islands. We speculate that this anomaly may correspond to the source of a plume which generated the Azores hotspot. Previously, a low S velocity in this depth range was found with SRF techniques beneath a few other hotspots.

Modelling of n-stage Blumlein stacked lines for bipolar pulse generation

A Blumlein line is a particular Pulse Forming Line, PFL, configuration that allows the generation of high-voltage sub-microsecond square pulses, with the same voltage amplitude as the dc charging voltage, into a matching load. By stacking n Blumlein lines one can multiply in theory by n the input dc voltage charging amplitude. In order to understand the operating behavior of this electromagnetic system and to further optimize its operation it is fundamental to theoretically model it, that is to calculate the voltage amplitudes at each circuit point and the time instant that happens. In order to do this, one needs to define the reflection and transmission coefficients where impedance discontinuity occurs. The experimental results of a fast solid-state switch, which discharges a three stage Blumlein stack, will be compared with theoretical ones.

Cape Verde hotspot from the upper crust to the top of the lower mantle

We investigate the crust, upper mantle and mantle transition zone of the Cape Verde hotspot by using seismic P and S receiver functions from several tens of local seismograph stations. We find a strong discontinuity at a depth of similar to 10 km underlain by a similar to 15-km thick layer with a high (similar to 1.9) Vp/Vs velocity ratio. We interpret this discontinuity and the underlying layer as the fossil Moho, inherited from the pre-hotspot era, and the plume-related magmatic underplate. Our uppermost-mantle models are very different from those previously obtained for this region: our S velocity is much lower and there are no indications of low densities. Contrary to previously published arguments for the standard transition zone thickness our data indicate that this thickness under the Cape Verde islands is up to similar to 30 km less than in the ambient mantle. This reduction is a combined effect of a depression of the 410-km discontinuity and an uplift of the 660-km discontinuity. The uplift is in contrast to laboratory data and some seismic data on a negligible dependence of depth of the 660-km discontinuity on temperature in hotspots. A large negative pressure-temperature slope which is suggested by our data implies that the 660-km discontinuity may resist passage of the plume. Our data reveal beneath the islands a reduction of S velocity of a few percent between 470-km and 510-km depths. The low velocity layer in the upper transition zone under the Cape Verde archipelago is very similar to that previously found under the Azores and a few other hotspots. In the literature there are reports on a regional 520-km discontinuity, the impedance of which is too large to be explained by the known phase transitions. Our observations suggest that the 520-km discontinuity may present the base of the low-velocity layer in the transition zone. (C) 2011 Elsevier B.V. All rights reserved.

Boulder deposition during major tsunami events

A remarkable accumulation of marine boulders located above the present spring tide level has occurred in two coastal lowlands of the Algarve (Portugal). The size-interval of the particles studied here is seldom reported in the literature in association with extreme events of coastal inundation, thus making this study of relevance to many other coasts worldwide. The spreads of boulders extend several hundred meters inland and well beyond the present landward limit of storm activity. The marine origin of the boulders is demonstrated by well-developed macro-bioerosion sculpturing and in situ skeletal remains of endolithic shallow marine bivalves. The good state preservation of the fossils within the boulders indicates that abrasion duringtransport and redeposition was not significant. We envisage boulder deposition as having taken place during the Lisbon tsunami of ad 1755 through the simultaneous landward entrainment of coarse particles from nearshore followed by rapid shoreward suspended-dominated transport and non-graded redeposition that excluded significant sorting by weight or boulder dimensions. We use numerical hydrodynamic modeling of tsunami (and storm) waves to test the observational data on boulder dimensions (density, size, distribution) on the most likely processes of sediment deposition. This work demonstrates the effectiveness of the study of boulder deposits in tsunami reconstruction. Copyright (C) 2011 John Wiley & Sons, Ltd.