Laboratory Study of Structural Behavior of Alternative Dowel Bars, April 2006

Load transfer across transverse joints has always been a factor contributing to the useful life of concrete pavements. For many years, round steel dowels have been the conventional load transfer mechanism. Many problems have been associated with the round steel dowels. The most detrimental effect of the steel dowel is corrosion. Repeated loading over time also damages joints. When a dowel is repeatedly loaded over a long period of time, the high bearing stresses found at the top and bottom edge of a bar erode the surrounding concrete. This oblonging creates multiple problems in the joint. Over the past decade, Iowa State University has performed extensive research on new dowel shapes and materials to mitigate the effects of oblonging and corrosion. This report evaluates the bearing stress performance of six different dowel bar types subjected to two different shear load laboratory test methods. The first load test is the AASHTO T253 method. The second procedure is an experimental cantilevered dowel test. The major objective was to investigate and improve the current AASHTO T253 test method for determining the modulus of dowel support, k0. The modified AASHTO test procedure was examined alongside an experimental cantilever dowel test. The modified AASHTO specimens were also subjected to a small-scale fatigue test in order to simulate long-term dowel behavior with respect to concrete joint damage. Loss on ignition tests were also performed on the GFRP dowel specimens to determine the resin content percentage. The study concluded that all of the tested dowel bar shapes and materials were adequate with respect to performance under shear loading. The modified AASHTO method yielded more desirable results than the ones obtained from the cantilever test. The investigators determined that the experimental cantilever test was not a satisfactory test method to replace or verify the AASHTO T253 method.

Competition, innovation and growth with limited commitment

We study how barriers to business start-up affect the investment in knowledge capital when contracts are not enforceable. Barriers to business start-up lower the competition for knowledge capital and, in absence of commitment, reduce the incentive to accumulate knowledge. As a result, countries with large barriers experience lower income and growth. Our results are consistent with cross-country evidence showing that the cost of business start-up is negatively correlated with the level and growth of income.

Bank versus venture capital

Why do some start-up firms raise funds from banks andothers from venture capitalists? To answer this question,I develop a model of start-up financing when intellectualproperty rights are not well protected. The upside of VCfinancing is that the VC understands the business betterthan a bank. The downside, however, is that the VC maysteal the idea and use it himself. The results of themodel are consistent with empirical regularities onstart-up financing. The model implies that thecharacteristics of the firms financing from venturecapitalists are low-collateral, high-growth and high-profitability. The model also suggests that thetighter protection of intellectual property rightscontributes to the recent dramatic growth of the USventure capital industry.

Tidibi

Tidibi es una nueva comunidad digital que permite a sus miembros hacer pujas por ofertas de ocio exclusivas al precio que ellos decidan. En este momento estas ofertas de ocio se centran en hoteles de cuatro y cinco estrellas, pero está previsto lanzar pronto packs de esquí, cruceros y, más adelante, espectáculos. El usuario ganador de la oferta es aquel queha ofrecido un precio más alto (apéndices 1, 2 y 3) cuando el cronómetro que cuenta atrás llega a cero, y puede decidir cuántas noches quiere pasar en ese hotel (hasta un máximo de tres) a ese precio.La sociedad gestora de Tidibi, “Dragon Deal”, se constituyó jurídicamente como una S.L. el 6 de julio de 2012, pero el lanzamiento oficial de la página web www.tidibi.com no ocurrió hasta el 4 de octubre de este año. Sus creadores son un grupo de cuatro emprendedores (apéndice 4) que se conocieron en el curso de sus estudios MBA en la escuela de negocios IESE de Barcelona.Tidibi es un concepto innovador, basado en los nuevos usos de las tecnologías y en la línea de las nuevas tendencias del mercado, en el que existe una relación participativa por partede los clientes, en vez del tradicional rol del agente pasivo que espera que le hagan llegar la información. Dado que el precio es la principal barrera para que los compradores cibernéticos hagan sus compras on-line (iPerceptions “Hospitality and Tourism Industryreport” para Q4 2011), parece que Tidibi puede ofrecer una solución a esta problemática y hacer "business" con ello.Por lo que respecta a la inversión requerida, los emprendedores estiman una cantidad total de 450.000€, que se desglosa de la siguiente manera: 60.000€ fondos iniciales de la start-up, 140.000€ necesidades de capital circulante y 250.000€ de marketing y esfuerzo de ventas.Sin embargo, también reconocen que podrían funcionar con una inversión inferior, dadoque podrían adaptar y reducir la última de las partidas arriba mencionadas. A pesar de ello, creemos que una reducción significativa de esfuerzos en marketing podría comprometer eléxito de la empresa. Por ahora han conseguido cerca de la mitad del presupuesto en una ronda de financiación interna y un préstamo participativo de un fondo de capital riesgo. No podemos proveer más datos por razones de confidencialidad.

Critical behavior of a system with orientational and positional degrees of freedom: A Monte Carlo simulation study

The critical behavior of a system constituted by molecules with a preferred symmetry axis is studied by means of a Monte Carlo simulation of a simplified two-dimensional model. The system exhibits two phase transitions, associated with the vanishing of the positional order of the center of mass of the molecules and with the orientational order of the symmetry axis. The evolution of the order parameters and the specific heat is also studied. The transition associated with the positional degrees of freedom is found to change from a second-order to a first-order behavior when the two phase transitions are close enough, due to the coupling with the orientational degrees of freedom. This fact is qualitatively compared with similar results found in pure liquid crystals and liquid-crystal mixtures.

Atomic structure of the nanocrystalline Si particles appearing in nanostructured Si thin films produced in low-temperature radiofrequency plasmas

Nanostructured Si thin films, also referred as polymorphous, were grown by plasma-enhanced chemical vapor deposition. The term "polymorphous" is used to define silicon material that consists of a two-phase mixture of amorphous and ordered Si. The plasma conditions were set to obtain Si thin films from the simultaneous deposition of radical and ordered nanoparticles. Here, a careful analysis by electron transmission microscopy and electron diffraction is reported with the aim to clarify the specific atomic structure of the nanocrystalline particles embedded in the films. Whatever the plasma conditions, the electron diffraction images always revealed the existence of a well-defined crystalline structure different from the diamondlike structure of Si. The formation of nanocrystallinelike films at low temperature is discussed. A Si face-cubic-centered structure is demonstrated here in nanocrystalline particles produced in low-pressure silane plasma at room temperature.

Influence of the dipolar interactions in the magnetization reversal asymmetry of hard-soft magnetic ribbons

Partial crystallization of the metallic glass Co66Si16B12Fe4Mo2 was performed by annealing at temperatures between 500 and 540°C for 10-20 min, resulting in crystallite volume fractions of (0.7-5)×10¿3 and sizes of 50-100 nm. This two-phase alloy presents a remarkable feature: a hysteresis loop shift that can be tailored by simply premagnetizing the sample in the adequate magnetic field. Shifts as large as five times the coercive field have been obtained which make them interesting for application as magnetic cores in dc pulse transformers. The asymetrical magnetic reversal is explained in terms of the magnetic dipolar field interaction and the observed hysteresis loops have been satisfactorily simulated by a modification of Stoner-Wohlfarth¿s model of coherent rotations.

Precursor phenomena in frustrated systems

To understand the origin of the dynamical transition, between high-temperature exponential relaxation and low-temperature nonexponential relaxation, that occurs well above the static transition in glassy systems, a frustrated spin model, with and without disorder, is considered. The model has two phase transitions, the lower being a standard spin glass transition (in the presence of disorder) or fully frustrated Ising (in the absence of disorder), and the higher being a Potts transition. Monte Carlo results clarify that in the model with (or without) disorder the precursor phenomena are related to the Griffiths (or Potts) transition. The Griffiths transition is a vanishing transition which occurs above the Potts transition and is present only when disorder is present, while the Potts transition which signals the effect due to frustration is always present. These results suggest that precursor phenomena in frustrated systems are due either to disorder and/or to frustration, giving a consistent interpretation also for the limiting cases of Ising spin glass and of Ising fully frustrated model, where also the Potts transition is vanishing. This interpretation could play a relevant role in glassy systems beyond the spin systems case.

Thermodynamic investigations in the Si-Ge-rich part of the ruthenium-silicon-germanium system

This paper reports molar heat capacities of Ru50SixGe(50-x) and Ru40SiyGe(60-y) ternary solid solutions determined by differential scanning calorimetry. A second order transition has been characterised for alloys ranging from Ru40Ge60 to Ru40Si10Ge50 at temperatures ranging from 850 to 1040 K, respectively. Tie lines have been established at 1000-900-800-700-600 degrees C by electron microprobe measurements on annealed alloys of the two phase domains: Ru50SixGe(50-x)-Ru40SiyGe(60-y) and Ru40SiyGe(60-y)-SizGe(100-z).

Characterization of a genomic signature of pregnancy identified in the breast.

The objective of this study was to comprehensively compare the genomic profiles in the breast of parous and nulliparous postmenopausal women to identify genes that permanently change their expression following pregnancy. The study was designed as a two-phase approach. In the discovery phase, we compared breast genomic profiles of 37 parous with 18 nulliparous postmenopausal women. In the validation phase, confirmation of the genomic patterns observed in the discovery phase was sought in an independent set of 30 parous and 22 nulliparous postmenopausal women. RNA was hybridized to Affymetrix HG_U133 Plus 2.0 oligonucleotide arrays containing probes to 54,675 transcripts, scanned and the images analyzed using Affymetrix GCOS software. Surrogate variable analysis, logistic regression, and significance analysis of microarrays were used to identify statistically significant differences in expression of genes. The false discovery rate (FDR) approach was used to control for multiple comparisons. We found that 208 genes (305 probe sets) were differentially expressed between parous and nulliparous women in both discovery and validation phases of the study at an FDR of 10% and with at least a 1.25-fold change. These genes are involved in regulation of transcription, centrosome organization, RNA splicing, cell-cycle control, adhesion, and differentiation. The results provide initial evidence that full-term pregnancy induces long-term genomic changes in the breast. The genomic signature of pregnancy could be used as an intermediate marker to assess potential chemopreventive interventions with hormones mimicking the effects of pregnancy for prevention of breast cancer.

Evaluation of Asphalt Mix Permeability, MLR-90-2, 1992

Efforts to eliminate rutting on the Interstate system have resulted in 3/4 in. aggregate mixes, with 75 blow Marshall, 85% crushed aggregate mix designs. On a few of these projects paved in 1988-1989, water has appeared on the surfaces. Some conclusions have been reached by visual on-sight investigations that the water is coming from surface water, rain and melting snow gaining entry into the surface asphalt mixture, then coming back out in selected areas. Cores were taken from several Interstate projects and tested for permeability to investigate the surface water theory that supposedly happens with only the 3/4 in. mixtures. All cores were of asphalt overlays over portland cement concrete, except for the Clarke County project which is full depth AC. The testing consisted of densities, permeabilities, voids by high pressure airmeter (HPAM), extraction, gradations, AC content, and film thicknesses. Resilient modulus, indirect tensile and retained strengths after freeze/thaw were also done. All of the test results are about as expected. Permeabilities, the main reason for testing, ranged from 0.00 to 2.67 ft per day and averages less than 1/2 ft per day if the following two tests are disregarded. One test on each binder course came out to 15.24 ft/day, and a surface course at 13.78 ft/day but these are not out of supposedly problem projects.

Stepwise evaluation of syncope: a prospective population-based controlled study.

BACKGROUND: Evaluation of syncope remains often unstructured. The aim of the study was to assess the effectiveness of a standardized protocol designed to improve the diagnosis of syncope. METHODS: Consecutive patients with syncope presenting to the emergency departments of two primary and tertiary care hospitals over a period of 18 months underwent a two-phase evaluation including: 1) noninvasive assessment (phase I); and 2) specialized tests (phase II), if syncope remained unexplained after phase I. During phase II, the evaluation strategy was alternately left to physicians in charge of patients (control), or guided by a standardized protocol relying on cardiac status and frequency of events (intervention). The primary outcomes were the diagnostic yield of each phase, and the impact of the intervention (phase II) measured by multivariable analysis. RESULTS: Among 1725 patients with syncope, 1579 (92%) entered phase I which permitted to establish a diagnosis in 1061 (67%) of them, including mainly reflex causes and orthostatic hypotension. Five-hundred-eighteen patients (33%) were considered as having unexplained syncope and 363 (70%) entered phase II. A cause for syncope was found in 67 (38%) of 174 patients during intervention periods, compared to 18 (9%) of 189 during control (p<0.001). Compared to control periods, intervention permitted diagnosing more cardiac (8%, vs 3%, p=0.04) and reflex syncope (25% vs 6%, p<0.001), and increased the odds of identifying a cause for syncope by a factor of 4.5 (95% CI: 2.6-8.7, p<0.001). Overall, adding the diagnostic yield obtained during phase I and phase II (intervention periods) permitted establishing the cause of syncope in 76% of patients. CONCLUSION: Application of a standardized diagnostic protocol in patients with syncope improved the likelihood of identifying a cause for this symptom. Future trials should assess the efficacy of diagnosis-specific therapy.

Sprinkle Treatment of Asphalt Surfaces, HR-199, 1984

Methods of improving highway safety are of major concern to everyone who is involved in the planning, development and construction of improvements of our vast highway network. Other major concerns are the conservation of our rapidly disappearing sources of energy and quality building materials. This research is devoted to further exploration of a process which will: 1. help preserve higher quality aggregates; and, 2. improve the frictional characteristics and surface texture of asphalt pavement surfaces. Sprinkle treatment of asphalt concrete pavement surfaces with a non-polishing aggregate, a procedure which was developed in Europe, is one method which has shown promise in accomplishing the above listed objectives. This research seeks to explore the feasibility and cost effectiveness of using standard asphalt mixtures of local, less expensive aggregates for surface courses followed by a surface sprinkle treatment of a hard, durable, non-polishing layer of precoated chips to produce a durable, non-skid pavement surface for safe highway travel. Three standard mixture types are being evaluated for aggregate retention characteristics and six sprinkle aggregates are being evaluated for durability, polishing and friction characteristics. In addition, measurements of the surface texture by the silicone putty method are being made. Another feature of this research is the evaluation of a rubberized asphalt material called Overflex MS as a crack filler. It has been reported that the material could be beneficial in reducing reflective cracking. The project was begun in July of 1978 and was completed in August. A review made in the spring of 1979 indicates very satisfactory performance. It was determined from slide photos taken after construction and again in the spring that aggregate retention was very good. However, many cracks had reflected indicating that the Overflex MS had not been effective. Follow up friction test results and texture analysis were also very good. The results of these tests are shown in Appendix A.

Evaluation of Alternative Methods to Obtain Specific Gravity of Coarse Aggregate, MLR-89-7, 1990

AASHTO has a standard test method for determining the specific gravity of aggregates. The people in the Aggregate Section of the Central Materials Laboratory perform the AASHTO T-85 test for AMRL inspections and reference samples. Iowa's test method 201B, for specific gravity determinations, requires more time and more care to perform than the AASHTO procedure. The major difference between the two procedures is that T-85 requires the sample to be weighed in water and 201B requires the 2 quart pycnometer jar. Efficiency in the Central Laboratory would be increased if the AASHTO procedure for coarse aggregate specific gravity determinations was adopted. The questions to be answered were: (1) Do the two procedures yield the same test results? (2) Do the two procedures yield the same precision? An experiment was conducted to study the different test methods. From the experimental results, specific gravity determinations by AASHTO T-85 method were found to correlate to those obtained by the Iowa 201B method with an R-squared value of 0.99. The absorption values correlated with an R-squared value of 0.98. The single operator precision was equivalent for the two methods. Hence, this procedure was recommended to be adopted in the Central Laboratory.

Validation of real-time methylation-specific PCR to determine O6-methylguanine-DNA methyltransferase gene promoter methylation in glioma.

Epigenetic silencing of the DNA repair protein O(6)-methylguanine-DNA methyltransferase (MGMT) by promoter methylation predicts successful alkylating agent therapy, such as with temozolomide, in glioblastoma patients. Stratified therapy assignment of patients in prospective clinical trials according to tumor MGMT status requires a standardized diagnostic test, suitable for high-throughput analysis of small amounts of formalin-fixed, paraffin-embedded tumor tissue. A direct, real-time methylation-specific PCR (MSP) assay was developed to determine methylation status of the MGMT gene promoter. Assay specificity was obtained by selective amplification of methylated DNA sequences of sodium bisulfite-modified DNA. The copy number of the methylated MGMT promoter, normalized to the beta-actin gene, provides a quantitative test result. We analyzed 134 clinical glioma samples, comparing the new test with the previously validated nested gel-based MSP assay, which yields a binary readout. A cut-off value for the MGMT methylation status was suggested by fitting a bimodal normal mixture model to the real-time results, supporting the hypothesis that there are two distinct populations within the test samples. Comparison of the tests showed high concordance of the results (82/91 [90%]; Cohen's kappa = 0.80; 95% confidence interval, 0.82-0.95). The direct, real-time MSP assay was highly reproducible (Pearson correlation 0.996) and showed valid test results for 93% (125/134) of samples compared with 75% (94/125) for the nested, gel-based MSP assay. This high-throughput test provides an important pharmacogenomic tool for individualized management of alkylating agent chemotherapy.