Metric Short Course for the Office of Bridges and Structures, HR-378, 1995

This metric short course was developed in response to a request from the Office of Bridges and Structures to assist in the training of engineers in the use of metric units of measure which will be required in all highway designs and construction after September 30, 1996 (CFR Presidential Executive Order No. 12770). The course notes which are contained in this report, were developed for a half-day course. The course contains a brief review of metrication in the U.S., metric units, prefixes, symbols, basic conversions, etc. The unique part of the course is that it presents several typical bridge calculations (such as capacity of reinforced concrete compression members, strength of pile caps, etc.) worked two ways: inch-pound units throughout with end conversion to metric and initial hard conversion to metric with metric units throughout. Comparisons of partial results and final results (obtained by working the problems the two ways) are made for each of the example problems.

Fatigue and Residual Stress Investigation of Composite Prestressed Steel Beams, HR-74, 1963

Two composite, prestressed, steel beams, fabricated by slightly different methods, were fatigue tested to destruction. Stresses and deflections were measured at regular intervals, and the behavior of each beam as failure progressed was recorded. Residual stresses were then evaluated by testing segments of each beam. An attempt was made to assess the effects of the residual stresses on fatigue strength.

A Feasibility Study on Embedded Micro-Electromechanical Sensors and Systems (MEMS) for Monitoring Highway Structures, TR-575, 2011

Micro-electromechanical systems (MEMS) provide vast improvements over existing sensing methods in the context of structural health monitoring (SHM) of highway infrastructure systems, including improved system reliability, improved longevity and enhanced system performance, improved safety against natural hazards and vibrations, and a reduction in life cycle cost in both operating and maintaining the infrastructure. Advancements in MEMS technology and wireless sensor networks provide opportunities for long-term continuous, real-time structural health monitoring of pavements and bridges at low cost within the context of sustainable infrastructure systems. The primary objective of this research was to investigate the use of MEMS in highway structures for health monitoring purposes. This study focused on investigating the use of MEMS and their potential applications in concrete through a comprehensive literature review, a vendor survey, and a laboratory study, as well as a small-scale field study. Based on the comprehensive literature review and vendor survey, the latest information available on off-the-shelf MEMS devices, as well as research prototypes, for bridge, pavement, and traffic applications were synthesized. A commercially-available wireless concrete monitoring system based on radio-frequency identification (RFID) technology and off-the-shelf temperature and humidity sensors were tested under controlled laboratory and field conditions. The test results validated the ability of the RFID wireless concrete monitoring system in accurately measuring the temperature both inside the laboratory and in the field under severe weather conditions. In consultation with the project technical advisory committee (TAC), the most relevant MEMS-based transportation infrastructure research applications to explore in the future were also highlighted and summarized.

Wind Tunnel Analysis of the Effects of Planting at Highway Grade Separation Structures, HR-202, 1979

Blowing and drifting snow has been a problem for the highway maintenance engineer virtually since the inception of the automobile. In the early days, highway engineers were limited in their capability to design and construct drift free roadway cross sections, and the driving public tolerated the delays associated with snow storms. Modern technology, however, has long since provided the design expertise, financial resources, and construction capability for creating relatively snowdrift free highways, and the driver today has come to expect a highway facility that is free of snowdrifts, and if drifts develop they expect highway maintenance crews to open the highway within a short time. Highway administrators have responded to this charge for better control of snowdrifting. Modern highway designs in general provide an aerodynamic cross section that inhibits the deposition of snow on the roadway insofar as it is economically feasible to do so.

Evaluation of Control Structures for Stabilizing Degrading Stream Channels in Western Iowa, Phases II and III, HR-208A, 1985

Since the turn of the century, tributaries to the Missouri River in western Iowa have entrenched their channels to as much as six times their original depth. This channel degradation is accompanied by widening as the channel side slopes become unstable and landslides occur. The deepening and widening of these streams have endangered about 25% of the highway bridges in 13 counties [Lohnes et al. 1980]. Grade stabilization structures have been recommended as the most effective remedial measure for stream degradation [Brice et al., 1978]. In western Iowa, within the last seven years, reinforced concrete grade stabilization structures have cost between $300,000 and $1,200,000. Recognizing that the high cost of these structures may be prohibitive in many situations, the Iowa Department of Transportation (Iowa DOT) sponsored a study at Iowa State University (ISU) to find low-cost alternative structures. This was Phase I of the stream degradation study. Analytical and laboratory work led to the conclusion that alternative construction materials such as gabions and soil-cement might result in more economical structures [Lohnes et al. 1980]. The ISU study also recommended that six experimental structures be built and their performance evaluated. Phase II involved the design of the demonstration structures, and Phase III included monitoring and evaluating their performance.

Evaluation of Steel Bridges, Volumes I & II, TR-493, 2007

This report is divided into two volumes. This volume (Volume I) summarizes a structural health monitoring (SHM) system that was developed for the Iowa DOT to remotely and continuously monitor fatigue critical bridges (FCB) to aid in the detection of crack formation. The developed FCB SHM system enables bridge owners to remotely monitor FCB for gradual or sudden damage formation. The SHM system utilizes fiber bragg grating (FBG) fiber optic sensors (FOSs) to measure strains at critical locations. The strain-based SHM system is trained with measured performance data to identify typical bridge response when subjected to ambient traffic loads, and that knowledge is used to evaluate newly collected data. At specified intervals, the SHM system autonomously generates evaluation reports that summarize the current behavior of the bridge. The evaluation reports are collected and distributed to the bridge owner for interpretation and decision making. Volume II summarizes the development and demonstration of an autonomous, continuous SHM system that can be used to monitor typical girder bridges. The developed SHM system can be grouped into two main categories: an office component and a field component. The office component is a structural analysis software program that can be used to generate thresholds which are used for identifying isolated events. The field component includes hardware and field monitoring software which performs data processing and evaluation. The hardware system consists of sensors, data acquisition equipment, and a communication system backbone. The field monitoring software has been developed such that, once started, it will operate autonomously with minimal user interaction. In general, the SHM system features two key uses. First, the system can be integrated into an active bridge management system that tracks usage and structural changes. Second, the system helps owners to identify damage and deterioration.

Evaluation de deux structures à bas seuil de la ville de Lausanne : Le Passage et le Point d'eau

[Table des matières] 1. Méthodes d'évaluation. 2. Le Passage et le Point d'eau. 2.1. Historique et objectifs. 2.2. Etapes de la mise en route. 3.1. Professionnels salariés. 3.2. Bénévoles professionnels. 3.3. Bénévoles d'accueil. 4.1. Activités de la structure. 4.2. Accueil (animations, repas, collations). 4.3. L'offre socio-éducative. 4.4. L'offre sanitaire. 4.5. La distribution du matériel stérile. 5.1. Prestations d'hygiène. 5.2. Soins somatiques. 5.3. Activité sportive. 6.1. Profil des usagers. 6.2. Indicateurs socio-démographiques et d'intégration sociale. 6.3. Etat de santé perçu. 6.4. Fréquentation du réseau (dispositif bas seuil et autre) et de Point d'eau. 7. Consommation de drogues illégales. 8. Fréquentation de la structure. 9.1. Méthodes d'évaluation utilisées. 9.2. Evaluation du Passage et du Point d'eau.

Investigation of Field Corrosion Performance and Bond/Development Length of Galvanized Reinforcing Steel, TR-666, 2014

In reinforced concrete systems, ensuring that a good bond between the concrete and the embedded reinforcing steel is critical to long-term structural performance. Without good bond between the two, the system simply cannot behave as intended. The bond strength of reinforcing bars is a complex interaction between localized deformations, chemical adhesion, and other factors. Coating of reinforcing bars, although sometimes debated, has been commonly found to be an effective way to delay the initiation of corrosion in reinforced concrete systems. For many years, the standard practice has been to coat reinforcing steel with an epoxy coating, which provides a barrier between the steel and the corrosive elements of water, air, and chloride ions. Recently, there has been an industry-led effort to use galvanizing to provide the protective barrier commonly provided by traditional epoxy coatings. However, as with any new structural product, questions exist regarding both the structural performance and corrosion resistance of the system. In the fall of 2013, Buchanan County, Iowa constructed a demonstration bridge in which the steel girders and all internal reinforcing steel were galvanized. The work completed in this project sought to understand the structural performance of galvanized reinforcing steel as compared to epoxy-coated steel and to initiate a long-term corrosion monitoring program. This work consisted of a series of controlled laboratory tests and the installation of a corrosion monitoring system that can be observed for years in the future. The results of this work indicate there is no appreciable difference between the bond strength of epoxy-coated reinforcing steel and galvanized reinforcing steel. Although some differences were observed, no notable difference in either peak load, slip, or failure mode could be identified. Additionally, a long-term monitoring system was installed in this Buchanan County bridge and, to date, no corrosion activity has been identified.

Qui utilise les crèches en Suisse ? : logiques sociales du recours aux structures d'accueil collectif pour la petite enfance

Depuis quelque temps, de plus en plus de spécialistes de la politique sociale préconisent une stratégie d'investissement social dans laquelle les crèches joueraient un rôle majeur. Cette stratégie vise à prévenir les exclusions sociales par la promotion de l'égalité des chances et de l'accès à l'emploi en vue d'un allègement des dépenses de protection sociale passive. Outre qu'elles permettent aux familles d'avoir deux revenus, les crèches ont en effet l'avantage de réduire les écarts au niveau des compétences cognitives et linguistiques entre les enfants venant de différents milieux sociaux. Mais le succès d'une telle stratégie présuppose que certains publics cibles recourent effectivement aux crèches, à savoir les ménages disposant d'un faible revenu ou/et de niveau de formation, ainsi que les familles issues de l'immigration. Or, des analyses statistiques sur la base de l'Enquête suisse sur la population active (ESPA) de 2008 montrent que, pour les familles en Suisse, les chances d'utiliser une crèche augmentent avec le niveau de formation des parents. Concernant plus particulièrement le niveau de formation des mères, ce phénomène n'est d'ailleurs que partiellement conditionné par le taux d'activité supérieur de celles ayant accompli une formation de degré tertiaire. En outre, certaines populations d'immigrés dont l'intégration dans la société suisse est réputée difficile sont peu disposées à recourir aux crèches. Les immigrés de première génération de quasiment toutes les origines fortement représentées en Suisse ont en revanche plus de chances que les parents d'origine suisse de faire appel au service d'une crèche à raison d'au moins 4 jours/semaine, ce qui peut influer négativement sur le comportement de l'enfant. Ce dernier résultat semble paradoxal mais montre qu'une migration rend plus difficile l'organisation d'une garde informelle comme solution complémentaire à la crèche. En synthèse, la présente étude attire l'attention sur le fait que les atouts pédagogiques et socialisants des crèches reviennent avant tout aux enfants de parents d'origine suisse ou venant de pays culturellement proches et ayant un niveau de formation supérieur. Telle que conçue actuellement, l'offre de crèches en Suisse ne semble guère opérer comme un instrument efficace de l'investissement social. Immer mehr Experten der Sozialpolitik empfehlen eine ,,Strategie der sozialen Investitionen", die den Kindertagesstätten (bzw. Kinderkrippen) eine wichtige Rolle zuschreibt. Ziel dieser Strategie ist es, durch Förderung von Chancengleichheit und Arbeitsmarktpartizipation sozialen Ausgrenzungen vorzubeugen, um Einsparungen im Bereich der passiven Sozialleistungen zu ermöglichen. Krippen haben einerseits den Vorteil, dass sie es den Familien ermöglichen, zwei Einkommen zu erzielen. Andererseits tragen sie zur Minderung von kognitiven und sprachlichen Fähigkeitsunterschieden zwischen Vorschulkindern aus verschiedenen sozialen Milieus bei. Der Erfolg dieser Strategie setzt jedoch voraus, dass gewisse Zielgruppen tatsächlich Krippen nutzen, nämlich bezüglich Einkommen und/oder Bildung benachteiligte Haushalte sowie Familien mit Migrationshintergrund. Die vorliegenden statistischen Analysen aufgrund der SAKE-Daten von 2008 (Schweizerische Arbeitskräfteerhebung) ergeben jedoch für die Schweiz, dass die Wahrscheinlichkeit, eine Krippe zu nutzen, mit dem Bildungsniveau der Eltern steigt. Was das Bildungsniveau der Mütter im Besonderen anbelangt, ist dieses Phänomen nur teilweise bedingt durch den tendenziell höheren Beschäftigungsgrad der besser Ausgebildeten. Zudem haben einige Migrantengruppen, deren Integration in die Schweizer Gesellschaft als besonders schwierig betrachtet wird, eine bedeutend tiefere Benützungswahrscheinlichkeit als Eltern Schweizer Herkunft. Für fast alle in der Schweiz stark vertretenen Migranten erster Generation ist dennoch das statistische Risiko grösser, die Krippe während mindestens 4 Tagen/Woche zu nutzen, was einen negativen Einfluss auf das Verhalten des Kindes haben kann. Dieses scheinbar paradoxe Ergebnis ist darauf zurückzuführen, dass ein Migrationshintergrund das Organisieren von krippenergänzenden Betreuungslösungen informeller Art meist erschwert. Gesamthaft zeigt die vorliegende Studie auf, dass die positiven pädagogischen und sozialisierenden Effekte der Krippen in erster Linie Kindern zugutekommen, deren Eltern eine höhere Ausbildung haben, Schweizer Herkunft sind oder aus einem kulturell nahestehenden Land kommen. So wie es gegenwärtig eingerichtet ist, scheint das Krippenangebot in der Schweiz kaum als effizientes Instrument sozialer Investitionen zu wirken.

The Flexural Fatigue Strength of Prestressed Steel I-Beams, HR-73, 1962

The purpose of this investigation was to study the flexural fatigue strength of two prestressed steel I-beams which had previously been fabricated in connection with a jointly sponsored project under the auspices of the Iowa State Highway Commission. The beams were prestressed by deflecting them under the action of a concentrated load at the center of a simple span, then welding unstressed high strength steel plates to the top and bottom flanges to retain a predetermined amount of prestress. The beams were rolled sections of A36 steel and the plates were USS "T-1" steel. Each of the two test specimens were subjected to an identical repeated loading until a fatigue failure occurred. The loading was designed to produce stresses equivalent to those which would have occurred in a simulated bridge and amounted to 84 percent of a standard H-15 live load including impact. One of the beams sustained 2,469,100 repetitions of load to failure and the other sustained 2,756,100 cycles. Following the fatigue tests, an experimental study was made to determine the state of stress that had been retained in the prestressed steel beams. This information, upon which the calculated stresses of the test could be superimposed, provided a method of correlating the fatigue strength of the beams with the fatigue information available on the two steels involved.