Freezing Point Depressions of Dilute Solutions of Alkali Metal Chlorides and Bromides

Freezing point depressions (¿Tf) of dilute solutions of several alkali metal chlorides and bromides were calculated by means of the best activity coefficient equations. In the calculations, Hückel, Hamer and Pitzer equationswere used for activity coefficients. The experimental ¿Tf values available in the literature for dilute LiCl, NaCl and KBr solutions can be predicted within experimental error by the Hückel equations used. The experimental ¿Tf values for dilute LiCl and KBr solutions can also be accurately calculated by corresponding Pitzer equations and those for dilute NaCl solutions by the Hamer equation for this salt. Neither Hamer nor Pitzer equations predict accurately the freezing points reported in the literature for LiBr and NaBr solutions. The ¿Tf values available for dilute solutions of RbCl, CsCl or CsBr are not known at the moment accurately because the existing data for these solutions are not precise. The freezing point depressions are tabulated in the present study for LiCl, NaCl and KBr solutions at several rounded molalities. The ¿Tf values in this table can be highly recommended. The activity coefficient equations used in the calculation of these values have been tested with almost allhigh-precision electrochemical data measured at 298.15 K.

Isentropic Exergy and Pressure of the Shock Wave Caused by the Explosion of a Pressure Vessel

An accidental burst of a pressure vessel is an uncontrollable and explosion-like batch process. In this study it is called an explosion. The destructive effectof a pressure vessel explosion is relative to the amount of energy released in it. However, in the field of pressure vessel safety, a mutual understanding concerning the definition of explosion energy has not yet been achieved. In this study the definition of isentropic exergy is presented. Isentropic exergy is the greatest possible destructive energy which can be obtained from a pressure vessel explosion when its state changes in an isentropic way from the initial to the final state. Finally, after the change process, the gas has similar pressure and flow velocity as the environment. Isentropic exergy differs from common exergy inthat the process is assumed to be isentropic and the final gas temperature usually differs from the ambient temperature. The explosion process is so fast that there is no time for the significant heat exchange needed for the common exergy.Therefore an explosion is better characterized by isentropic exergy. Isentropicexergy is a characteristic of a pressure vessel and it is simple to calculate. Isentropic exergy can be defined also for any thermodynamic system, such as the shock wave system developing around an exploding pressure vessel. At the beginning of the explosion process the shock wave system has the same isentropic exergyas the pressure vessel. When the system expands to the environment, its isentropic exergy decreases because of the increase of entropy in the shock wave. The shock wave system contains the pressure vessel gas and a growing amount of ambient gas. The destructive effect of the shock wave on the ambient structures decreases when its distance from the starting point increases. This arises firstly from the fact that the shock wave system is distributed to a larger space. Secondly, the increase of entropy in the shock waves reduces the amount of isentropic exergy. Equations concerning the change of isentropic exergy in shock waves are derived. By means of isentropic exergy and the known flow theories, equations illustrating the pressure of the shock wave as a function of distance are derived. Amethod is proposed as an application of the equations. The method is applicablefor all shapes of pressure vessels in general use, such as spheres, cylinders and tubes. The results of this method are compared to measurements made by various researchers and to accident reports on pressure vessel explosions. The test measurements are found to be analogous with the proposed method and the findings in the accident reports are not controversial to it.

Ion-exchange resins as stationary phase in reactive chromatography

Dynamic behavior of bothisothermal and non-isothermal single-column chromatographic reactors with an ion-exchange resin as the stationary phase was investigated. The reactor performance was interpreted by using results obtained when studying the effect of the resin properties on the equilibrium and kinetic phenomena occurring simultaneously in the reactor. Mathematical models were derived for each phenomenon and combined to simulate the chromatographic reactor. The phenomena studied includes phase equilibria in multicomponent liquid mixture¿ion-exchange resin systems, chemicalequilibrium in the presence of a resin catalyst, diffusion of liquids in gel-type and macroporous resins, and chemical reaction kinetics. Above all, attention was paid to the swelling behavior of the resins and how it affects the kinetic phenomena. Several poly(styrene-co-divinylbenzene) resins with different cross-link densities and internal porosities were used. Esterification of acetic acid with ethanol to produce ethyl acetate and water was used as a model reaction system. Choosing an ion-exchange resin with a low cross-link density is beneficial inthe case of the present reaction system: the amount of ethyl acetate as well the ethyl acetate to water mole ratio in the effluent stream increase with decreasing cross-link density. The enhanced performance of the reactor is mainly attributed to increasing reaction rate, which in turn originates from the phase equilibrium behavior of the system. Also mass transfer considerations favor the use ofresins with low cross-link density. The diffusion coefficients of liquids in the gel-type ion-exchange resins were found to fall rapidly when the extent of swelling became low. Glass transition of the polymer was not found to significantlyretard the diffusion in sulfonated PS¿DVB ion-exchange resins. It was also shown that non-isothermal operation of a chromatographic reactor could be used to significantly enhance the reactor performance. In the case of the exothermic modelreaction system and a near-adiabatic column, a positive thermal wave (higher temperature than in the initial state) was found to travel together with the reactive front. This further increased the conversion of the reactants. Diffusion-induced volume changes of the ion-exchange resins were studied in a flow-through cell. It was shown that describing the swelling and shrinking kinetics of the particles calls for a mass transfer model that explicitly includes the limited expansibility of the polymer network. A good description of the process was obtained by combining the generalized Maxwell-Stefan approach and an activity model that was derived from the thermodynamics of polymer solutions and gels. The swelling pressure in the resin phase was evaluated by using a non-Gaussian expression forthe polymer chain length distribution. Dimensional changes of the resin particles necessitate the use of non-standard mathematical tools for dynamic simulations. A transformed coordinate system, where the mass of the polymer was used as a spatial variable, was applied when simulating the chromatographic reactor columns as well as the swelling and shrinking kinetics of the resin particles. Shrinking of the particles in a column leads to formation of dead volume on top of the resin bed. In ordinary Eulerian coordinates, this results in a moving discontinuity that in turn causes numerical difficulties in the solution of the PDE system. The motion of the discontinuity was eliminated by spanning two calculation grids in the column that overlapped at the top of the resin bed. The reactive and non-reactive phase equilibrium data were correlated with a model derived from thethermodynamics of polymer solution and gels. The thermodynamic approach used inthis work is best suited at high degrees of swelling because the polymer matrixmay be in the glassy state when the extent of swelling is low.

Potentiometric titration as a method of determining the stoichiometric dissociation constants of weak acids from the thermodynamic dissociation constants of aqueous solutions at 298.15 K

The simple single-ion activity coefficient equation originating from the Debye-Hückel theory was used to determine the thermodynamic and stoichiometric dissociation constants of weak acids from data concerning galvanic cells. Electromotive force data from galvanic cells without liquid junctions, which was obtained from literature, was studied in conjuction with the potentiometric titration data relating to aqueous solutions at 298.15 K. The dissociation constants of weak acids could be determined by the presented techniques and almost all the experimental data studied could be interpreted within the range of experimental error. Potentiometric titration has been used here and the calculation methods were developed to obtain the thermodynamic and stoichiometric dissociation constants of some weak acids in aqueous solutions at 298.15 K. The ionic strength of titrated solutions were adjusted using an inert electrolyte, namely, sodium or potassium chloride. Salt content alonedetermines the ionic strength. The ionic strength of the solutions studied varied from 0.059 mol kg-1 to 0.37 mol kg-1, and in some cases up to 1.0 mol kg-1. The following substances were investigated using potentiometric titration: aceticacid, propionic acid, L-aspartic acid, L-glutamic acid and bis(2,2-dimethyl-3-oxopropanol) amine.

Selective catalytic reduction of nitrogen oxides with ammonia in forced unsteady state reactors - Case based reasoning and mathematical model simulation reasoning

The application of forced unsteady-state reactors in case of selective catalytic reduction of nitrogen oxides (NOx) with ammonia (NH3) is sustained by the fact that favorable temperature and composition distributions which cannot be achieved in any steady-state regime can be obtained by means of unsteady-state operations. In a normal way of operation the low exothermicity of the selective catalytic reduction (SCR) reaction (usually carried out in the range of 280-350°C) is not enough to maintain by itself the chemical reaction. A normal mode of operation usually requires supply of supplementary heat increasing in this way the overall process operation cost. Through forced unsteady-state operation, the main advantage that can be obtained when exothermic reactions take place is the possibility of trapping, beside the ammonia, the moving heat wave inside the catalytic bed. The unsteady state-operation enables the exploitation of the thermal storage capacity of the catalyticbed. The catalytic bed acts as a regenerative heat exchanger allowing auto-thermal behaviour when the adiabatic temperature rise is low. Finding the optimum reactor configuration, employing the most suitable operation model and identifying the reactor behavior are highly important steps in order to configure a proper device for industrial applications. The Reverse Flow Reactor (RFR) - a forced unsteady state reactor - corresponds to the above mentioned characteristics and may be employed as an efficient device for the treatment of dilute pollutant mixtures. As a main disadvantage, beside its advantages, the RFR presents the 'wash out' phenomena. This phenomenon represents emissions of unconverted reactants at every switch of the flow direction. As a consequence our attention was focused on finding an alternative reactor configuration for RFR which is not affected by the incontrollable emissions of unconverted reactants. In this respect the Reactor Network (RN) was investigated. Its configuration consists of several reactors connected in a closed sequence, simulating a moving bed by changing the reactants feeding position. In the RN the flow direction is maintained in the same way ensuring uniformcatalyst exploitation and in the same time the 'wash out' phenomena is annulated. The simulated moving bed (SMB) can operate in transient mode giving practically constant exit concentration and high conversion levels. The main advantage of the reactor network operation is emphasizedby the possibility to obtain auto-thermal behavior with nearly uniformcatalyst utilization. However, the reactor network presents only a small range of switching times which allow to reach and to maintain an ignited state. Even so a proper study of the complex behavior of the RN may give the necessary information to overcome all the difficulties that can appear in the RN operation. The unsteady-state reactors complexity arises from the fact that these reactor types are characterized by short contact times and complex interaction between heat and mass transportphenomena. Such complex interactions can give rise to a remarkable complex dynamic behavior characterized by a set of spatial-temporal patterns, chaotic changes in concentration and traveling waves of heat or chemical reactivity. The main efforts of the current research studies concern the improvement of contact modalities between reactants, the possibility of thermal wave storage inside the reactor and the improvement of the kinetic activity of the catalyst used. Paying attention to the above mentioned aspects is important when higher activity even at low feeding temperatures and low emissions of unconverted reactants are the main operation concerns. Also, the prediction of the reactor pseudo or steady-state performance (regarding the conversion, selectivity and thermal behavior) and the dynamicreactor response during exploitation are important aspects in finding the optimal control strategy for the forced unsteady state catalytic tubular reactors. The design of an adapted reactor requires knowledge about the influence of its operating conditions on the overall process performance and a precise evaluation of the operating parameters rage for which a sustained dynamic behavior is obtained. An apriori estimation of the system parameters result in diminution of the computational efforts. Usually the convergence of unsteady state reactor systems requires integration over hundreds of cycles depending on the initial guess of the parameter values. The investigation of various operation models and thermal transfer strategies give reliable means to obtain recuperative and regenerative devices which are capable to maintain an auto-thermal behavior in case of low exothermic reactions. In the present research work a gradual analysis of the SCR of NOx with ammonia process in forced unsteady-state reactors was realized. The investigation covers the presentationof the general problematic related to the effect of noxious emissions in the environment, the analysis of the suitable catalysts types for the process, the mathematical analysis approach for modeling and finding the system solutions and the experimental investigation of the device found to be more suitable for the present process. In order to gain information about the forced unsteady state reactor design, operation, important system parameters and their values, mathematical description, mathematicalmethod for solving systems of partial differential equations and other specific aspects, in a fast and easy way, and a case based reasoning (CBR) approach has been used. This approach, using the experience of past similarproblems and their adapted solutions, may provide a method for gaining informations and solutions for new problems related to the forced unsteady state reactors technology. As a consequence a CBR system was implemented and a corresponding tool was developed. Further on, grooving up the hypothesis of isothermal operation, the investigation by means of numerical simulation of the feasibility of the SCR of NOx with ammonia in the RFRand in the RN with variable feeding position was realized. The hypothesis of non-isothermal operation was taken into account because in our opinion ifa commercial catalyst is considered, is not possible to modify the chemical activity and its adsorptive capacity to improve the operation butis possible to change the operation regime. In order to identify the most suitable device for the unsteady state reduction of NOx with ammonia, considering the perspective of recuperative and regenerative devices, a comparative analysis of the above mentioned two devices performance was realized. The assumption of isothermal conditions in the beginningof the forced unsteadystate investigation allowed the simplification of the analysis enabling to focus on the impact of the conditions and mode of operation on the dynamic features caused by the trapping of one reactant in the reactor, without considering the impact of thermal effect on overall reactor performance. The non-isothermal system approach has been investigated in order to point out the important influence of the thermal effect on overall reactor performance, studying the possibility of RFR and RN utilization as recuperative and regenerative devices and the possibility of achieving a sustained auto-thermal behavior in case of lowexothermic reaction of SCR of NOx with ammonia and low temperature gasfeeding. Beside the influence of the thermal effect, the influence of the principal operating parameters, as switching time, inlet flow rate and initial catalyst temperature have been stressed. This analysis is important not only because it allows a comparison between the two devices and optimisation of the operation, but also the switching time is the main operating parameter. An appropriate choice of this parameter enables the fulfilment of the process constraints. The level of the conversions achieved, the more uniform temperature profiles, the uniformity ofcatalyst exploitation and the much simpler mode of operation imposed the RN as a much more suitable device for SCR of NOx with ammonia, in usual operation and also in the perspective of control strategy implementation. Theoretical simplified models have also been proposed in order to describe the forced unsteady state reactors performance and to estimate their internal temperature and concentration profiles. The general idea was to extend the study of catalytic reactor dynamics taking into account the perspectives that haven't been analyzed yet. The experimental investigation ofRN revealed a good agreement between the data obtained by model simulation and the ones obtained experimentally.

Compromise solutions for bankruptcy situations: a note

Although classic bankruptcy problems take into account a single claims vector, Pulido et al. (2008) show that there are real bankruptcy situations where agents face more than one reference vector. In particular, they consider the claims and an additional reference vector. To analyze these situations, they propose the extreme and the diagonal approaches. Nonetheless, the former approach depends on the order of the vectors: if we interchange the claims and the reference vectors, the result changes. Moreover their study is limited to the case in which the reference vector is lower than the claims vector. In the present note, we propose an extension that solves these short- comings by introducing the idea of impartiality. Keywords: bankruptcy problems; reference point; compromise solution; impartiality.

Power spectral changes of the superimposed M wave during isometric voluntary contractions of increasing strength.

INTRODUCTION: We examined the power spectral changes of the compound muscle action potential (M wave) evoked during isometric contractions of increasing strength. METHODS: Surface electromyography (sEMG) of the vastus lateralis and medialis was recorded from 20 volunteers who performed 4-s step-wise isometric contractions of different intensities. A maximal M wave was elicited by a single stimulus to the femoral nerve and superimposed on the voluntary contractions. The spectral characteristics (Fmean and Fmedian) of sEMG and M-wave signals were calculated. RESULTS: M-wave spectral indicators increased systematically with contraction intensity up to 60% MVC and then leveled off at higher forces. Over the 10-60% MVC range, the increase in spectral indicators was 3 times higher for M waves (36%) than for sEMG (12%). CONCLUSIONS: The consistent increase in M-wave spectral characteristics with force is due to the fact that the number of motor units recruited by the superimposed supramaximal stimulus is approximately stable.

Dilaton quantum cosmology in two dimensions

We consider a renormalizable two-dimensional model of dilaton gravity coupled to a set of conformal fields as a toy model for quantum cosmology. We discuss the cosmological solutions of the model and study the effect of including the back reaction due to quantum corrections. As a result, when the matter density is below some threshold new singularities form in a weak-coupling region, which suggests that they will not be removed in the full quantum theory. We also solve the Wheeler-DeWitt equation. Depending on the quantum state of the Universe, the singularities may appear in a quantum region where the wave function is not oscillatory, i.e., when there is not a well-defined notion of classical spacetime.

Properties of amorphous silicon thin films grown in square wave modulated silane rf discharges.

Hydrogenated amorphous silicon (a‐Si:H) thin films have been obtained from pure SiH4 rf discharges by using the square wave modulation (SQWM) method. Film properties have been studied by means of spectroellipsometry, thermal desorption spectrometry, photothermal deflection spectroscopy and electrical conductivity measurements, as a function of the modulation frequency of the rf power amplitude (0.2-4000 Hz). The films deposited at frequencies about 1 kHz show the best structural and optoelectronic characteristics. Based upon the experimental results, a qualitative model is presented, which points up the importance of plasma negative ions in the deposition of a‐Si:H from SQWM rf discharges through their influence on powder particle formation.

Uusien energianormien vaikutus pientalojen rakenteisiin ympäristön kannalta

Tehokkaimpia keinoja vähentää rakennusten lämmitysenergian kulutusta ja lämmityksen aiheuttavia hiilidioksidi- ja happamoitavia päästöjä on tiukentaa rakentamismääräysten lämmöneristysvaatimuksia. Hyvin lämmöneristetyissä, tiiveissä ja ilmanvaihdoltaan optimoiduissa taloissa on pienet lämpöhäviöt. Näin ympäristöä kuormittava vaikutus saadaan paljon vähemmäksi kuin nykynormien mukaisissa asuinrakennuksissa. Johtumislämpöhäviö pienenee suoraan eristekerroksia paksuntamalla ja siihen on helpointa vaikuttaa. Mitä suurempiin eristepaksuuksiin mennään sen suuremmaksi tulee konvektion osuus kokonaislämpöhäviöstä. Tulevaisuudessa parempia ratkaisuja haetaan erityisesti konvektiosta ja säteilystä aiheutuvien lämpöhäviöiden pienentämiseksi. Eristeen osastointi ilmanpitävillä, vesihöyryä diffuusisesti läpäisevillä pystysuuntaisilla konvektiokatkoilla vähentää tehokkaasti paksun seinäeristeen kuljettumis-ilmavirtauksia. Katkoina käytetään erilaisia kalvoja ja rakennuspapereita, joilla on pieni emissiviteetti. Katkojen merkitys kasvaa, kun mennään uusien normien mukaisiin eristepaksuuksiin. Lämmöneriste voidaan toteuttaa myös kokoamalla ohuita kalvoja paketiksi, jotka jakavat ilmatilan ja siis eristeelle varatun paksuuden suljettuihin ilmaväleihin. Kun kalvoiksi valitaan pieniemissiviteettisiä pintoja, saadaan säteilylämmönsiirto lähes eliminoiduksi. Tällaisen ilmatilan lämmönjohtumisluku lähestyy paikallaan pysyvän ilman lämmönjohtumislukua, l = 0,025 W/Km, eli tällä rakennesysteemillä on mahdollista toteuttaa ohuempia rakenteita kuin perinteisillä eristeillä. Hygroskooppisen massan käyttö sisäilman kosteutta tasaavana rakenteena voi olla tulevaisuutta. Kehitystyö tuottaa uusia, kosteusteknisesti toimivia sovelluksia. Toisaalta palomääräykset tulevat kehitystyötä vastaan. Hygroskooppinen pintamateriaali on kevyt (pieni tiheys) ja paloteknisesti arka. Suoraa sähkölämmitystä ei voida pitää ympäristöystävällisenä. Sen jalostusketju on pitkä ja monivaiheinen. Millä peruspolttoaineella sähköä tuotetaan, vaikuttaa asiaan luonnollisestikin. Suoraa sähkölämmitystä voidaan suositella vain yksinäisen ihmisen taloudessa lämmitysmuotona taloudellisista syistä. Halvan polttoaineen säästöllä ei voida maksaa suuria laiteinvestointeja. Aurinkoenergian hyvä hyödyntäminen edellyttää hyvää säätöä, joka kytkee lämmityksen pois päältä silloin, kun aurinko lämmittää. Auringon hetkelliset säteilytehot ovat suuria verrattuna rakenteen lämpöhäviöihin ja huonetilojen lämmöntarpeeseen. Ratkaisu aurinkoenergian hetkellisyyteen ja paikallisuuteen on energian siirtäminen lämmöntarpeen mukaan rakennuksen eri osiin ja sen varastoiminen päivätasolla. Kun varastoivasta massasta ei ole suoraa yhteyttä ulos, voidaan kerääjäeristeeltä saatu lämpö käyttää häviöttömästi huonetilojen lämmittämiseen. Vaikka lämmitysenergian käytössä päästään 30 % vähennyksiin uudisrakennusten osalta, ei kokonaisenergian käyttö merkittävästi pienene, jos taloussähkön kulutus pysyy vakiona. Sama pätee myös CO2 -päästöihin. Saavutettava etu lämmitys-energian kulutuksessa voidaan hukata yhä suurenevaksi taloussähkön käytöksi, mikä olisi erityisen huono asia ympäristön kannalta.

PHOTOCATALYTIC OXIDATION OF AQUEOUS SOLUTIONS OF JET FUEL AND ICING INHIBITORS

The present paper is devoted to the results of experimental research undertaken into photocatalytical oxidation (PCO) of aqueous solutions of de-icing agents and aqueous extract of jet fuel. The report consists of introduction, literature review, description of materials and methods, discussion of results and conclusions. TiO2 was selected as a photocatalyst for the experiments with synthetic solutions of ethylene glycol, 2-ethoxyethanol and aqueous extract of jet fuel. To explain the PCO mechanisms affecting certain behaviour of de-icing agent under distinctive conditions, the following factors were studied: the impact of initial concentration of pollutant, the role of pH, the presence of tert-butanol as OH·-radicals scavenger and mineral admixtures. PCO under solar radiation performed in two ways: catalysed by irradiated TiO2 slurry or by TiO2 attached to buoyant hollow glass micro-spheres. Special attention was paid to the energy-saving PCO with reduced intensity mixing of the slurry. The effect of PCO was assessed by determination of residual chemical oxygen demand of solution (COD) and by measuring of concentration of glycols. The PCO process efficiency was assumed to be dependent on the TiO2 suspension fractional composition. Thus, the following effects of solutions’ media were viewed: presence of organic admixtures, pH influence, mixing mode during the PCO. The effects of mineral admixtures - Ca2+, Fe3+/2+, Mn2+, SO42- - that are often present in natural and wastewater systems or produced during the degradation of organic pollutants and which can affect the rate of PCO of de-icing agents, were also investigated.

Secure IP-based Connection Solutions for Mobile Users

Tämä diplomityö tutkii turvallisia etäyhteystapoja yritysverkkoihin. Samanaikasesti kuin Internettiin liitetyt langattomat verkot, kuten langattomat lähiverkot ja pakettikytkentäiset matkapuhelinverkot, tulevat yhä yleisemmiksi, mahdollisuus etäyhteksien luomiseen näiden verkkojen kautta tulee yhä suositummaksi. Vaikka tietoverkot kehittyvät, pysyvät niitä uhkaavat yleisluontoiset uhat samoina. IP pohjaiset VPN-verkot ovat sopiva tapa suojata Internetin ylitse tapahtuvia etäyhteksiä. Eri VPN-ratkaisuja on kuitenkin tarjolla laaja valikoima. Oikean tyyppisen VPN-ratkaisun valinta on kriittistä, jotta yrityksen etäyhteystarpeet saadaan täytettyä. Diplomityö esittelee eräänä vaihtoehtona miten Pocket PC 2002 PDA laitetta ja Windows XP Professional käyttöjärjestelmää voidaan käyttää edullisen VPN ratkaisun toteuttamiseen.

Clinical management and burden of bipolar disorder: a multinational longitudinal study (WAVE-bd Study)

BACKGROUND: Studies in bipolar disorder (BD) to date are limited in their ability to provide a whole-disease perspective--their scope has generally been confined to a single disease phase and/or a specific treatment. Moreover, most clinical trials have focused on the manic phase of disease, and not on depression, which is associated with the greatest disease burden. There are few longitudinal studies covering both types of patients with BD (I and II) and the whole course of the disease, regardless of patients' symptomatology. Therefore, the Wide AmbispectiVE study of the clinical management and burden of Bipolar Disorder (WAVE-bd) (NCT01062607) aims to provide reliable information on the management of patients with BD in daily clinical practice. It also seeks to determine factors influencing clinical outcomes and resource use in relation to the management of BD. METHODS: WAVE-bd is a multinational, multicentre, non-interventional, longitudinal study. Approximately 3000 patients diagnosed with BD type I or II with at least one mood event in the preceding 12 months were recruited at centres in Austria, Belgium, Brazil, France, Germany, Portugal, Romania, Turkey, Ukraine and Venezuela. Site selection methodology aimed to provide a balanced cross-section of patients cared for by different types of providers of medical aid (e.g. academic hospitals, private practices) in each country. Target recruitment percentages were derived either from scientific publications or from expert panels in each participating country. The minimum follow-up period will be 12 months, with a maximum of 27 months, taking into account the retrospective and the prospective parts of the study. Data on demographics, diagnosis, medical history, clinical management, clinical and functional outcomes (CGI-BP and FAST scales), adherence to treatment (DAI-10 scale and Medication Possession Ratio), quality of life (EQ-5D scale), healthcare resources, and caregiver burden (BAS scale) will be collected. Descriptive analysis with common statistics will be performed. DISCUSSION: This study will provide detailed descriptions of the management of BD in different countries, particularly in terms of clinical outcomes and resources used. Thus, it should provide psychiatrists with reliable and up-to-date information about those factors associated with different management patterns of BD. TRIAL REGISTRATION NO: ClinicalTrials.gov: NCT01062607.