Microbial Treatment Of Rubber Latex Centrifugation Effluent

Many of the existing methods for the treatment of rubber latex centrifugation eflluent are not only unsatisfactory in their efliciency to effect near perfect treatment in bringing down the COD to optimum level, but also time consuming and need a large landspace. As the rate of effluent generation is extremely high (20 litres for kilogram of rubber) there is a need for development of efficient system,capable of rapid reduction of COD and BOD. Though the organic load of the rubber efiluent is very high, it does not contain much processed chemicals and therefore it can be considered as a ‘biological eflluent’. Further, the ratio of the Chemical Oxygen Demand to Biological Oxygen Demand (COD/BOD) of this effluent remain almost as a constant value. According to Montgomery (1967), estimation of BOD is not ideally suited for studies on process design, treatability, control of treatment plants, setting standards for treated effluents and assessing the effect of polluting discharges on the oxygen resources of receiving waters. Hence in the present study COD was measured to determine the impact of treatment system on the effluent. In the present study, attempts were made to evaluate the efficiencies of certain methods such as packed bed reactor using immobilized microbial cells, rotating biological contactor (RBC) and activated sludge process, for rapid and efficient treatment of natural rubber latex centrifugation effluent. In addition, studies were also carn'ed out to develop a suitable bioprocess for the coagulation of skim latex, as an alternative to the presently used acid coagulation process towards reducing the pollution load, besides recovering quality rubber

Dye-sensitized solar cells based on perylene derivatives

The oil price rises more and more, and the world energy consumption is projected to expand by 50 percent from 2005 to 2030. Nowadays intensive research is focused on the development of alternative energies. Among them, there are dye-sensitized nanocrystalline solar cells (DSSCs) “the third generation solar cells”. The latter have gained attention during the last decade and are currently subject of intense research in the framework of renewable energies as a low-cost photovoltaic. At present DSSCs with ruthenium based dyes exhibit highest efficiencies (ca 11%). The objective of the present work is to fabricate, characterize and improve the performance of DSSCs based on metal free dyes as sensitizers, especially on perylene derivatives. The work begins by a general introduction to the photovoltaics and dye-sensitized solar cells, such as the operating principles and the characteristics of the DSSCs. Chapter 2 and 3 discuss the state of the art of sensitizers used in DSSCs, present the compounds used as sensitizer in the present work and illustrate practical issues of experimental techniques and device preparation. A comparative study of electrolyte-DSSCs based on P1, P4, P7, P8, P9, and P10 are presented in chapter 4. Experimental results show that the dye structure plays a crucial role in the performance of the devices. The dye based on the spiro-concept (bipolar spiro compound) exhibited a higher efficiency than the non-spiro compounds. The presence of tert-butylpyridine as additive in the electrolyte was found to increase the open circuit voltage and simultaneously decrease the efficiency. The presence of lithium ions in the electrolyte increases both output current and the efficiency. The sensitivity of the dye to cations contained in the electrolyte was investigated in the chapter 5. FT-IR and UV-Vis were used to investigate the in-situ coordination of the cation to the adsorbed dye in the working devices. The open-circuit voltage was found to depend on the number of coordination sites in the dye. P1 with most coordination sites has shown the lowest potential drop, opposite to P7, which is less sensitive to cations in the working cells. A strategy to improve the dye adsorption onto the TiO2 surface, and thus the light harvesting efficiency of the photoanode by UV treatment, is presented in chapter 6. The treatment of the TiO2 film with UV light generates hydroxyl groups and renders the TiO2 surface more and more hydrophilic. The treated TiO2 surface reacts readily with the acid anhydride group of the dye that acts as an anchoring group and improves the dye adsorption. The short-circuit current density and the efficiency of the electrolyte-based dye cells was considerably improved by the UV treatment of the TiO2 film. Solid-state dye-sensitized solar cells (SSDs) based on spiro-MeOTAD (used as hole transport material) are studied in chapter 7. The efficiency of SSDs was globally found to be lower than that of electrolyte-based solar cells. That was due to poor pore filling of the dye-loaded TiO2 film by the spin-coated spiro-MeOTAD and to the significantly slower charge transport in the spiro-MeOTAD compared to the electrolyte redox mediator. However, the presence of the donor moieties in P1 that are structurally similar to spiro-MeOTAD was found to improve the wettability of the P1-loaded TiO2 film. As a consequence the performance of the P1-based solid-state cells is better compared to the cells based on non-spiro compounds.

Matter fluxes in mountain oases of Al Jabal Al Akhdar, Oman

Since 1970 when Sultan Qaboos bin Said Al Said took over power from this father, agriculture in Oman has undergone major transformations as a consequence of rapid population and economic growth. In this process groundwater extraction has dramatically increased to meet domestic and agricultural needs. Recently, the agro-ecosystem of ancient mountain oases of Oman have received greater attention as interest has grown to understand the causes of their often millennia old sustainable productivity. Particularly little is known about the carbon (C) and nutrient turnover in these intensive landuse systems. This is partly due to the difficulties to measure such processes in the often remote fields. To fill the existing gap of knowledge, field studies were conducted in five oases at different altitudes of Al Jabal Al Akhdar, the highest agricultural area in Oman, to determine C and nutrient fluxes as well as nutrient use efficiencies for two different cropping systems as affected by temperature, irrigation, and manure quality. The results of this study indicated that water scarcity as a result of low precipitation and an increase in urban water consumption is a major threat to the sustainability of agriculture in these oases. Optimizing the use of irrigation water is a major challenge for agriculture in these oases, particularly given ever increasing competition for this most limiting resource. Traditionally, farmers of these oases adapt to variation of irrigation water supply by minimizing the growing area of annual crops, leaving these areas uncultivated through drought seasons (Luedeling and Buerkert 2008). In this study, a remarkable reduction in annual crop area was observed in 2009 for all oases. Our results suggested that water scarcity as a result of low precipitation and the increase in urban water consumption cause such changes in land use. The data also underline the intensive C and nutrient turnover in the man-made irrigated agroecosystems and confirmed the importance of the large manure quantities applied continuously to the terraces as a key factor responsible for sustainable soil productivity. To trace the fate of C and plant nutrients that are released from the large amount of manure applied by oasis farmers, more detailed studies under controlled conditions, using isotope signatures, would be needed.

Effect of management strategies on the performance of ruminant livestock production systems and the safety of plant and animal products in the city of Sikasso, Mali

The regional population growth in West Africa, and especially its urban centers, will bring about new and critical challenges for urban development policy, especially in terms of ensuring food security and providing employment for the growing population. (Peri-) urban livestock and vegetable production systems, which can contribute significantly to these endeavours, are limited by various constraints, amongst them limited access to expensive production factors and their (in)efficient use. To achieve sustainable production systems with low consumer health risks, that can meet the urban increased demand, this doctoral thesis determined nutrient use efficiencies in representative (peri-) urban livestock production systems in three West African cities, and investigated potential health risks for consumers ensuing from there. The field study, which was conducted during July 2007 to December 2009, undertook a comparative analysis of (peri-) urban livestock production strategies across 210 livestock keeping households (HH) in the three West African cities of Kano/Nigeria (84 HH), Bobo Dioulasso/Burkina Faso (63 HH) and Sikasso/Mali (63 HH). These livestock enterprises were belonging to the following three farm types: commercial gardening plus field crops and livestock (cGCL; 88 HH), commercial livestock plus subsistence field cropping (cLsC; 109 HH) and commercial gardening plus semi-commercial livestock (cGscL; 13 HH) which had been classified in a preceding study; they represented the diversity of (peri-) urban livestock production systems in West Africa. In the study on the efficiency of ruminant livestock production, lactating cowsand sheep herd units were differentiated based on whether feed supplements were offered to the animals at the homestead (Go: grazing only; Gsf: mainly grazing plus some supplement feeding). Inflows and outflows of nutrients were quantified in these herds during 18 months, and the effects of seasonal variations in nutrient availability on animals’ productivity and reproductive performance was determined in Sikasso. To assess the safety of animal products and vegetables, contamination sources of irrigated lettuce and milk with microbiological contaminants, and of tomato and cabbage with pesticide residues in (peri-) urban agriculture systems of Bobo Dioulasso and Sikasso were characterized at three occasions in 2009. Samples of irrigation water, organic fertilizer and ix lettuce were collected in 6 gardens, and samples of cabbage and tomato in 12 gardens; raw and curdled milk were sampled in 6 dairy herds. Information on health risks for consumers of such foodstuffs was obtained from 11 health centers in Sikasso. In (peri-) urban livestock production systems, sheep and goats dominated (P<0.001) in Kano compared to Bobo Dioulasso and Sikasso, while cattle and poultry were more frequent (P<0.001) in Bobo Dioulasso and Sikasso than in Kano. Across cities, ruminant feeding relied on grazing and homestead supplementation with fresh grasses, crop residues, cereal brans and cotton seed cake; cereal grains and brans were the major ingredients of poultry feeds. There was little association of gardens and livestock; likewise field cropping and livestock were rarely integrated. No relation existed between the education of the HH head and the adoption of improved management practices (P>0.05), but the proportion of HH heads with a long-term experience in (peri-) urban agriculture was higher in Kano and in Bobo Dioulasso than in Sikasso (P<0.001). Cattle and sheep fetched highest market prices in Kano; unit prices for goats and chicken were highest in Sikasso. Animal inflow, outflow and dairy herd growth rates were significantly higher (P<0.05) in the Gsf than in the Go cattle herds. Maize bran and cottonseed expeller were the main feeds offered to Gsf cows as dry-season supplement, while Gsf sheep received maize bran, fresh grasses and cowpea pods. The short periodic transhumance of Go dairy cows help them maintaining their live weight, whereas Gsf cows lost weight during the dry season despite supplement feeding at a rate of 1506 g dry matter per cow and day, resulting in low productivity and reproductive performance. The daily live weight gains of calves and lambs, respectively, were low and not significantly different between the Go and the Gsf system. However, the average live weight gains of lambs were significantly higher in the dry season (P<0.05) than in the rainy season because of the high pressure of gastrointestinal parasites and of Trypanosoma sp. In consequence, 47% of the sheep leaving the Go and Gsf herds died due to diseases during the study period. Thermo-tolerant coliforms and Escherichia coli contamination levels of irrigation water significantly exceeded WHO recommendations for the unrestricted irrigation of vegetables consumed raw. Microbial contamination levels of lettuce at the farm gate and the market place in Bobo Dioulasso and at the farm gate in Sikasso were higher than at the market place in Sikasso (P<0.05). Pesticide residues were detected in only one cabbage and one tomato sample and were below the maximum residue limit for consumption. Counts of thermo-tolerant coliforms and Escherichia coli were higher in curdled than in raw milk (P<0.05). From 2006 to x 2009, cases of diarrhea/vomiting and typhoid fever had increased by 11% and 48%, respectively, in Sikasso. For ensuring economically successful and ecologically viable (peri-) urban livestock husbandry and food safety of (peri-) urban foodstuffs of animal and plant origin, the dissemination and adoption of improved feeding practices, livestock healthcare and dung management are key. In addition, measures fostering the safety of animal products and vegetables including the appropriate use of wastewater in (peri-) urban agriculture, restriction to approve vegetable pesticides and the respect of their latency periods, and passing and enforcement of safety laws is required. Finally, the incorporation of environmentally sound (peri-) urban agriculture in urban planning by policy makers, public and private extension agencies and the urban farmers themselves is of utmost importance. To enable an efficient (peri-) urban livestock production in the future, research should concentrate on cost-effective feeding systems that allow meeting the animals’ requirement for production and reproduction. Thereby focus should be laid on the use of crop-residues and leguminous forages. The improvement of the milk production potential through crossbreeding of local cattle breeds with exotic breeds known for their high milk yield might be an accompanying option, but it needs careful supervision to prevent the loss of the local trypanotolerant purebreds.

Ideotyping integrated aquaculture systems to balance soil nutrients

Due to growing land scarcity and lack of nutrient inputs, African farmers switched from shifting cultivation to continuous cropping and extended crop area by bringing fragile lands such as river banks and hill slopes into production. This accelerated soil fertility decline caused by erosion, harvesting and insufficient nutrient replenishment. We explored the feasibility to reduce nutrient depletion by increasing nutrient utilization efficiencies, while diversifying and increasing food production through the development of integrated aquaculture – agriculture (IAA). Considering the climatic conditions prevailing in Kenyan highlands, aquaculture production scenarios were ideotyped per agro-ecological zone. These aquaculture production scenarios were integrated into existing NUTrient MONitoring (NUTMON) farm survey data for the area. The nutrient balances and flows of the resulting IAA-systems were compared to present land use. The effects of IAA development on nutrient depletion and total food production were evaluated. With the development of IAA systems, nutrient depletion rates dropped by 23–35%, agricultural production increased by 2–26% and overall farm food production increased by 22–70%. The study demonstrates that from a bio-physical point of view, the development of IAA-systems in Africa is technically possible and could raise soil fertility and total farm production. Further studies that evaluate the economic feasibility and impacts on the livelihood of farming households are recommended.

Matter flows and balances in urban vegetable gardens of Bobo Dioulasso, Burkina Faso (West Africa)

Many efforts are undertaken for sustaining urban agriculture in African cities. This study therefore investigated nutrient management practices in urban vegetable gardens of Bobo Dioulasso, Burkina Faso (West Africa). Nitrogen (N), phosphorus (P), potassium (K), and carbon (C) fluxes were quantified and nutrient balances calculated for three gardens representing the typical commercial gardening + field crops and livestock system (cGCL) and three gardens representing the commercial gardening + semi-commercial field crop system (cGscC). Nutrient and C balances were similarly positive in both production systems reaching annual averages of 688 kg N ha -1, 251 kg P ha-1 yr-1, 189 kg K ha-1, and 31 t C ha-1. Inputs in all gardens exceeded the amounts recommended by the extension service. Gaseous emissions of N and C represented important pathways of N and C losses. The highest emission rates occurred during the hottest periods of the day and the peaks were observed after fertilizer applications. Management recommendations should be geared towards increasing nutrient use efficiencies by better tailoring nutrient availability to crop demand and adjusted fertilization techniques to mitigate N losses.

Technical and scale efficiency of cassava production system in Delta State, Nigeria: an application of Two-Stage DEA approach

The present study examines the level of pure technical and scale efficiencies of cassava production system including its sub-processes (that is production and processing stages) of 278 cassava farmers/processors from three regions of Delta State, Nigeria by applying Two-Stage Data Envelopment Analysis (DEA) approach. Results reveal that pure technical efficiency (PTE) is significantly lower at the production stage 0.41 vs 0.55 for the processing stage, but scale efficiency (SE) is high at both stages (0.84 and 0.87), implying that productivity can be improved substantially by reallocation of resources and adjusting operation size. The socio-economic determinants exert differential impacts on PTE and SE at each stage. Overall, education, experience and main occupation as farmer significantly improve SE while subsistence pressure reduces it. Extension contact significantly improves SE at the processing stage but reduces PTE and SE overall. Inverse size-PTE and size-SE relationships exist in cassava production system. In other words, large/medium farms are technically and scale inefficient. Gender gap exists in performance. Male farmers are technically efficient at processing stage but scale inefficient overall. Farmers in northern region are technically efficient. Investments in education, extension services and infrastructure are suggested as policy options to improve the cassava sector in Nigeria.

Simultaneous Drying and Separation of Composite Agricultural Material for Hay Processing

In composite agricultural materials such as grass, tee, medicinal plants; leaves and stems have a different drying time. By this behavior, after leaving the dryer, the stems may have greater moisture content than desired, while the leaves one minor, which can cause either the appearance of fungi or the collapse of the over-dried material. Taking into account that a lot of grass is dehydrated in forced air dryers, especially rotary drum dryers, this research was developed in order to establish conditions enabling to make a separation of the components during the drying process in order to provide a homogeneous product at the end. For this, a rotary dryer consisting of three concentric cylinders and a circular sieve aligned with the more internal cylinder was proposed; so that, once material enters into the dryer in the area of the inner cylinder, stems pass through sieve to the middle and then continue towards the external cylinder, while the leaves continue by the inner cylinder. For this project, a mixture of Ryegrass and White Clover was used. The characteristics of the components of a mixture were: Drying Rate in thin layer and in rotation, Bulk density, Projected Area, Terminal velocity, weight/Area Ratio, Flux through Rotary sieve. Three drying temperatures; 40°C, 60° C and 80° C, and three rotation speeds; 10 rpm, 20 rpm and 40 rpm were evaluated. It was found that the differences in drying time are the less at 80 °C when the dryer rotates at 40 rpm. Above this speed, the material adheres to the walls of the dryer or sieve and does not flow. According to the measurements of terminal velocity of stems and leaves of the components of the mixture, the speed of the air should be less than 1.5 m s-1 in the inner drum for the leaves and less than 4.5 m s-1 in middle and outer drums for stems, in such way that only the rotational movement of the dryer moves the material and achieves a greater residence time. In other hand, the best rotary sieve separation efficiencies were achieved when the material is dry, but the results are good in all the moisture contents. The best rotary speed of sieve is within the critical rotational speed, i.e. 20 rpm. However, the rotational speed of the dryer, including the sieve in line with the inner cylinder should be 10 rpm or less in order to achieve the greatest residence times of the material inside the dryer and the best agitation through the use of lifting flights. With a finite element analysis of a dryer prototype, using an air flow allowing speeds of air already stated, I was found that the best performance occurs when, through a cover, air enters the dryer front of the Middle cylinder and when the inner cylinder is formed in its entirety through a sieve. This way, air flows in almost equal amounts by both the middle and external cylinders, while part of the air in the Middle cylinder passes through the sieve towards the inner cylinder. With this, leaves do not adhere to the sieve and flow along drier, thanks to the rotating movement of the drums and the showering caused by the lifting flights. In these conditions, the differences in drying time are reduced to 60 minutes, but the residence time is higher for the stems than for leaves, therefore the components of the mixture of grass run out of the dryer with the same desired moisture content.

Reconfigurable Architectures for General-Purpose Computing

General-purpose computing devices allow us to (1) customize computation after fabrication and (2) conserve area by reusing expensive active circuitry for different functions in time. We define RP-space, a restricted domain of the general-purpose architectural space focussed on reconfigurable computing architectures. Two dominant features differentiate reconfigurable from special-purpose architectures and account for most of the area overhead associated with RP devices: (1) instructions which tell the device how to behave, and (2) flexible interconnect which supports task dependent dataflow between operations. We can characterize RP-space by the allocation and structure of these resources and compare the efficiencies of architectural points across broad application characteristics. Conventional FPGAs fall at one extreme end of this space and their efficiency ranges over two orders of magnitude across the space of application characteristics. Understanding RP-space and its consequences allows us to pick the best architecture for a task and to search for more robust design points in the space. Our DPGA, a fine- grained computing device which adds small, on-chip instruction memories to FPGAs is one such design point. For typical logic applications and finite- state machines, a DPGA can implement tasks in one-third the area of a traditional FPGA. TSFPGA, a variant of the DPGA which focuses on heavily time-switched interconnect, achieves circuit densities close to the DPGA, while reducing typical physical mapping times from hours to seconds. Rigid, fabrication-time organization of instruction resources significantly narrows the range of efficiency for conventional architectures. To avoid this performance brittleness, we developed MATRIX, the first architecture to defer the binding of instruction resources until run-time, allowing the application to organize resources according to its needs. Our focus MATRIX design point is based on an array of 8-bit ALU and register-file building blocks interconnected via a byte-wide network. With today's silicon, a single chip MATRIX array can deliver over 10 Gop/s (8-bit ops). On sample image processing tasks, we show that MATRIX yields 10-20x the computational density of conventional processors. Understanding the cost structure of RP-space helps us identify these intermediate architectural points and may provide useful insight more broadly in guiding our continual search for robust and efficient general-purpose computing structures.

Análisis del efecto de engranaje generado por la entrada en vigor del Tratado de Lisboa el 1 de diciembre de 2009 en el marco de la Política Común de Seguridad y Defensa (PCSD) en la Unión Europea

El proceso de integración en Unión Europea se caracteriza por la incorporación de los asuntos de seguridad exterior y defensa, tras el Tratado de Lisboa se enmarcaron en la PCSD. Dicha política por un proceso de integración progresiva, Spillover, ha tenido periodos de reactivación y de letargos.

Análisis del modelo de Internacionalización de e-Tech Simulation según la teoría de redes

La teoría de redes de Johanson y Mattson (1988) explica como las pequeñas empresas, también conocidas como PyMes, utilizan las redes de negocio para desarrollar sus procesos de internacionalización. Es así que a través de las redes pueden superar sus limitaciones de tamaño para encontrar cierto tipo de fluidez y dinamismo en su gestión, con el fin de aprovechar los beneficios de la internacionalización. A partir del desarrollo y fortalecimiento de las relaciones dentro de la red la organización puede posicionarse en una instancia competitiva cada vez más fuerte (Jarillo, 1988). Según Forsgren y Johanson (1992), para los gerentes es importante coordinar la interacción entre los diferentes actores de la red, ya que a través de estas su posición dentro de la red mejora y así mismo el flujo de recursos será mayor. El propósito de este trabajo es analizar el modelo de internacionalización según la teoría de redes, desde una perspectiva cultural, de e-Tech Simulation una PyME “Born to be global” norteamericana. Esta empresa ha minimizado su riesgo de internacionalización, a través del desarrollo de acuerdos entre los diferentes actores. Al mejorar su posición dentro de la red, es decir al fortalecer aún más los lazos existentes y crear nuevas relaciones, la empresa ha obtenido mayores beneficios de la misma y ha logrado ser aún más flexible con sus clientes. Es por esto que a partir de este análisis se planteó una serie de recomendaciones para mejorar los procesos de negociación dentro de la red, bajo un contexto cultural. De igual forma se evidencio la importancia del papel del emprendimiento del gerente en los procesos de internacionalización, así como su habilidad para mezclar los recursos obtenidos de diferentes mercados internacionales para satisfacer las necesidades de los clientes.

El virus de l'hepatitis C i la ribonucleasa Phumana: aspectes biològics i terapèutics

El virus de l'hepatitis C (VHC) provoca una hepatitis crònica que afecta a més de 170 milions de persones d'arreu del món. És un virus petit que es classifica dins de la família Flaviviridae i és un virus d'RNA de cadena positiva amb un genoma d'aproximadament 9.600 nucleòtids. A l'extrem 5' del genoma viral s'hi troba una regió no codificant (5'NCR) que comprèn els primers 341 nucleòtids i la seva funció està relaciona amb la traducció. Immediatament després hi ha una pauta de lectura oberta ORF que acaba en un únic codó d'aturada i codifica una poliproteïna de 3.010 aminoàcids. A continuació l'extrem 3' no codificant (3'NCR), que malgrat es desconeixen les seves funcions exactes, s'ha demostrat que és essencial per a la replicació vírica. La única poliproteïna generada és processada co- i postraduccionalment mitjançant proteases de l'hoste i víriques, donant lloc a les proteïnes estructurals (Core, E1 i E2-p7) i no estructurals (NS2-NS5B). Igual que la majoria de virus RNA, el VHC es caracteritza per tenir una taxa de mutació elevada. De fet, el genoma del virus no es pot definir com una única seqüència sinó per una població de variants molt relacionades entre sí. A aquesta manera d'organitzar la informació genètica se l'anomena quasiespècie viral i una de les seves implicacions principals és la facilitat amb què sorgeixen resistents al tractament. Els tractaments disponibles són llargs, cars, provoquen efectes secundaris considerables i només es resolen completament el 40% dels casos. Per aquesta raó es busquen altres solucions terapèutiques per combatre el virus entre les quals s'hi inclouen diferents estratègies. Una de les més innovadores i prometedores és la utilització de ribozims dirigits directament contra el genoma del virus. Aquest treball es centra en l'estudi de les noves estratègies terapèutiques basades en ribozims, concretament la ribonucleasa P. La ribonucleasa P és un ribozim que està present en tots els organismes ja que és l'enzim responsable de la maduració dels precursors d'RNA de transferència. El més interessant a nivell terapèutic és que s'ha demostrat que es pot dirigir la seva activitat cap a qualsevol RNA utilitzant una seqüència guia d'RNA que quan hibrida amb l'RNA diana, l'híbrid imita l'estructura secundària del substrat natural. En el cas del VHC, s'han estudiat ribozims dependents de seqüència (ribozims derivats d'RNAs satèl·lits i de viroides de plantes), sempre dirigits contra la regió més conservada del virus per evitar una disminució de l'eficiència del ribozim deguda a la variació de la diana. La ribonucleasa P és una endonucleasa d'activitat molt específica i es diferencia dels altres ribozims naturals en el sistema de reconeixement del substrat, reconeix elements estructurals i no de seqüència. L'objectiu final del treball és tallar in vitro l'RNA del VHC aprofitant la propietat que presenta aquest ribozim de reconèixer elements estructurals i no de seqüència ja que per a un mateix nombre de seqüències, el nombre d'estructures viables que pot adoptar l'RNA genòmic és molt més petit i per tant la variabilitat de la diana disminueix. S'han estudiat dos models d'RNasa P, la RNasa P humana guiada per seqüència guia externa (EGS) i l'RNA M1 de l'RNasa P d'E.coli unit a la seqüència guia per l'extrem 3' (ribozim M1GS). Abans però de dirigir el ribozim, s'han estudiat l'estructura i la variabilitat d'una regió del genoma del virus ja que s'ha descrit que són factors que poden limitar l'eficiència de qualsevol ribozim. Derivat d'aquests estudis s'aporten dades sobre accessibilitat i variabilitat d'una regió interna del genoma del virus de l'hepatitis C, la zona d'unió de la regió E2/NS2 (regió 2658-2869). L'estudi d'accessibilitat revela que la regió 2658-2869 del genoma del virus conté dominis oberts i tancats i que la transició entre uns i altres no és brusca si es compara amb altres regions d'estructura coneguda (regió 5' no codificant). Els resultats dels assajos in vitro amb els dos models de RNasa P mostren que s'ha aconseguit dirigir tant la ribonucleasa P humana com el ribozim M1GS cap a una zona, predeterminada segons l'estudi d'accessibilitat, com a poc estructurada i tallar l'RNA del virus. De l'anàlisi de mutacions, però, es dedueix que la regió estudiada és variable. Tot i dirigir el ribozim cap a la zona més accessible, la variació de la diana podria afectar la interacció amb la seqüència guia i per tant disminuir l'eficiència de tall. Si es proposés una estratègia terapèutica consistiria en un atac simultani de vàries dianes.D'altra banda i derivat d'un resultat inesperat on s'ha observat en els experiments control que l'extracte de RNasa P humana tallava l'RNA viral en absència de seqüències guia externes, s'ha caracteritzat una nova interacció entre l'RNA del VHC i la RNasa P humana. Per a la identificació de l'enzim responsable dels talls s'han aplicat diferents tècniques que es poden dividir en mètodes directes (RNA fingerprinting) i indirectes (immunoprecipitació i inhibicions competitives). Els resultats demostren que la ribonucleasa P humana, i no un altre enzim contaminant de l'extracte purificat, és la responsable dels dos talls específics observats i que es localitzen, un a l'entrada interna al ribosoma (IRES) i molt a prop del codó AUG d'inici de la traducció i l'altre entre la regió codificant estructural i no estructural. La ribonucleasa P és un dels enzims del metabolisme del tRNA que s'utilitza per identificar estructures similars al tRNA en substrats diferents del substrat natural. Així doncs, el fet que la ribonucleasa P reconegui i talli el genoma del VHC en dues posicions determinades suggereix que, a les zones de tall, el virus conté estructures semblants al substrat natural, és a dir estructures tipus tRNA. A més, tot i que el VHC és molt variable, els resultats indiquen que aquestes estructures poden ser importants per el virus, ja que es mantenen en totes les variants naturals analitzades. Creiem que la seva presència podria permetre al genoma interaccionar amb factors cel·lulars que intervenen en la biologia del tRNA,particularment en el cas de l'estructura tipus tRNA que es localitza a l'element IRES. Independentment però de la seva funció, es converteixen en unes noves dianes terapèutiques per a la RNasa P. S'ha de replantejar però l'estratègia inicial ja que la similitud amb el tRNA les fa susceptibles a l'atac de la ribonucleasa P, directament, en absència de seqüències guia externes.

Eliminación de compuestos causantes de olores mediante adsorbentes/catalizadores obtenidos a partir de lodos de depuradora

El aumento de la cantidad de lodos y las dificultades inherentes a su aplicación agrícola y/o disposición en vertederos, hace necesario encontrar nuevas alternativas para su gestión. A nivel europeo, hoy en día se tiende hacia la aplicación de tratamientos térmicos (incineración, pirólisis y gasificación) que permiten una valoración energética de los lodos, si bien generan un residuo sólido que sigue siendo necesario gestionar. El problema medioambiental provocado por (malos) olores resulta difícil de abordar de una manera genérica, teniendo en consideración la propia naturaleza del olor y sus posibles causas. Los olores en las EDARs son provocados básicamente por la degradación de la materia orgánica en condiciones anaeróbicas y se detectan en todas las operaciones unitarias en diferentes niveles de concentración. Esta tesis incidiendo en ambos aspectos, tiene por objeto investigar la valorización de lodos como materiales precursores de adsorbentes/ catalizadores para la eliminación de olores en el entorno de las EDARs, maximizando la reutilización de los lodos. Para la realización de los experimentos se han seleccionado lodos procedentes de tres EDARs situadas en la región de Girona (SC, SB, SL) que difieren en cuanto al tratamiento de los lodos. Ambas muestras han sido caracterizadas con el fin de determinar las diferencias más importantes en los lodos de partida. Los parámetros de caracterización incluyen el análisis de composición química (análisis elemental e inmediato, determinación contenido en cenizas, medida pH, DRX, FT-IR, SEM / EDX) así como análisis de superficie (adsorción de N2 y CO2). En primer lugar los lodos caracterizados han sido sometidos a diferentes tratamientos térmicos de gasificación y pirólisis y los adsorbentes/ catalizadores obtenidos se han probado como adsorbentes para la eliminación de H2S. Como consecuencia de este estudio, se ha desechado el uso de uno de lodos (SC) puesto que se obtenían resultados muy similares a (SB), a continuación el estudio se centró en el lodo de SL. Con este objetivo se han preparado 12 muestras 6 de ellas pirolizadas y 6 gasificadas en el rango de temperaturas que comprende 600-1100 ºC. Posteriormente las muestras han sido caracterizadas y se ha determinado la capacidad de eliminación (x/M) del H2S. Los resultados muestran que hemos sido capaces de obtener unos materiales que si bien, presentan un bajo desarrollo de porosidad dan lugar a valores de capacidades de eliminación elevados y comparables a carbones y materiales adsorbentes comerciales (Centaur, Sorbalit). Las elevadas eficiencias de eliminación se atribuyen básicamente a la presencia de especies catalíticamente activas tales como los óxidos mixtos de calcio y hierro determinados por DRX en las muestras tratadas térmicamente. El segundo bloque de resultados se centra la mejora de las propiedades texturales de estos materiales adsorbentes. Con este objetivo se llevaron acabo procesos de activación física con CO2 y química con H3PO4 e hidróxidos alcalinos (NaOH y KOH), que hasta el momento no se había probado con este tipo de precursores. Los resultados indican que la activación física (CO2) y química (H3PO4) no son unos buenos métodos para la obtención de adsorbentes altamente porosos con este tipo de materia prima bajo las condiciones probadas, sin embargo la activación con hidróxidos alcalinos da lugar a materiales adsorbentes con superficies específicas de hasta 1600 m2g-1. En el caso de la activación con hidróxidos, tanto el incremento de la relación agente activante/ precursor como el incremento de la temperatura producen un descenso del rendimiento, al mismo tiempo que incrementan el valor de SBET. Los materiales resultantes de la activación con hidróxidos alcalinos se han probado como adsorbentes/ catalizadores para la eliminación de H2S. Los resultados indican que un incremento del área superficial no es indicativo de un aumento de la capacidad de eliminación dada la naturaleza ácida de estos materiales obtenidos. Con el fin de contrarrestar el efecto ácido de estos materiales se han realizado los mismos ensayos añadiendo NaOH al lecho de reacción llegando a valores de x/M de hasta 450 mgg-1. Posteriormente también se han realizado ensayos de eliminación de NH3 con algunas de estas muestras, y los resultados obtenidos de x/M son del orden de carbones activados comerciales. Los materiales adsorbentes obtenidos tras la activación con hidróxidos alcalinos se convierten en materiales muy atractivos para ser utilizados como adsorbentes/ catalizadores de múltiples contaminantes (COVs, Hg...).

Museums and quality, from the concept of the museum that carries out functions to the museum that provides services

Quality management Self-evaluation of the organisation Citizens/customers satisfaction Impact on society evaluation Key performance evaluation Good practices comparison (Benchmarking) Continuous improvement In professional environments, when quality assessment of museums is discussed, one immediately thinks of the honourableness of the directors and curators, the erudition and specialisation of knowledge, the diversity of the gathered material and study of the collections, the collections conservation methods and environmental control, the regularity and notoriety of the exhibitions and artists, the building’s architecture and site, the recreation of environments, the museographic equipment design. We admit that the roles and attributes listed above can contribute to the definition of a specificity of museological good practice within a hierarchised functional perspective (the museum functions) and for the classification of museums according to a scale, validated between peers, based on “installed” appreciation criteria, enforced from above downwards, according to the “prestige” of the products and of those who conceive them, but that say nothing about the effective satisfaction of the citizen/customers and the real impact on society. There is a lack of evaluation instruments that would give us a return of all that the museum is and represents in contemporary society, focused on being and on the relation with the other, in detriment of the ostentatious possession and of the doing in order to meet one’s duties. But it is only possible to evaluate something by measurement and comparison, on the basis of well defined criteria, from a common grid, implicating all of the actors in the self-evaluation, in the definition of the aims to fulfil and in the obtaining of results.

A Generic Deformable Model for Vehicle Recognition

This paper reports the development of a highly parameterised 3-D model able to adopt the shapes of a wide variety of different classes of vehicles (cars, vans, buses, etc), and its subsequent specialisation to a generic car class which accounts for most commonly encountered types of car (includng saloon, hatchback and estate cars). An interactive tool has been developed to obtain sample data for vehicles from video images. A PCA description of the manually sampled data provides a deformable model in which a single instance is described as a 6 parameter vector. Both the pose and the structure of a car can be recovered by fitting the PCA model to an image. The recovered description is sufficiently accurate to discriminate between vehicle sub-classes.