Surface recombination at semiconductor electrodes: a single level study

The recombination and the faradaic fluxes are shown to be sensitive to the location of a single level recombination center, when it is located near the band edges. As the surface level is shifted deeper into the band gap from either of the band edges, the back emission terms are dominated by electron capture and hole capture terms, and the occupancy of the surface level is no longer determined by its location in the band gap. However, when one of the back emission terms determines the surface state occupancy, it is shown that there exists a simple relation between the value of the surface level and the recombination and the faradaic fluxes respectively. Expressions to this effect are derived and verified in the case of the recombination flux, which characterized by the potential at which it attains its maximum value. For the faradaic flux the results are qualitative.

A New Liquid Level Sensor for Process-Control Applications

Many process-control systems are air-operated. In such an environment, it would be desirable and economical to use pneumatic sensors. Bubble-back pressure sensors perform quite satisfactorily, but in case of viscous inflammable and slurry-like liquids with a tendency to froth, this level sensor is inadequate. The method suggested in this paper utilizes a pneumatic capacitor, one boundary of which is formed by the liquid level, to modulate a fluid amplifier feedback oscillator. The absence of moving parts and economy obtained makes this method attractive for process-control applications. The system has been mathematically modeled and simulated on an IBM 360/44 digital computer. Experimental values compare fairly well with the theoretical results. For the range tested, the sensor is found to have a linear frequency variation with the liquid level Extended running in the laboratory shows that the system is very reliable. This system has been found insensitive to temperature variations of up to 15ðC.

Rate Control State-of-the-art Survey

The majority of Internet traffic use Transmission Control Protocol (TCP) as the transport level protocol. It provides a reliable ordered byte stream for the applications. However, applications such as live video streaming place an emphasis on timeliness over reliability. Also a smooth sending rate can be desirable over sharp changes in the sending rate. For these applications TCP is not necessarily suitable. Rate control attempts to address the demands of these applications. An important design feature in all rate control mechanisms is TCP friendliness. We should not negatively impact TCP performance since it is still the dominant protocol. Rate Control mechanisms are classified into two different mechanisms: window-based mechanisms and rate-based mechanisms. Window-based mechanisms increase their sending rate after a successful transfer of a window of packets similar to TCP. They typically decrease their sending rate sharply after a packet loss. Rate-based solutions control their sending rate in some other way. A large subset of rate-based solutions are called equation-based solutions. Equation-based solutions have a control equation which provides an allowed sending rate. Typically these rate-based solutions react slower to both packet losses and increases in available bandwidth making their sending rate smoother than that of window-based solutions. This report contains a survey of rate control mechanisms and a discussion of their relative strengths and weaknesses. A section is dedicated to a discussion on the enhancements in wireless environments. Another topic in the report is bandwidth estimation. Bandwidth estimation is divided into capacity estimation and available bandwidth estimation. We describe techniques that enable the calculation of a fair sending rate that can be used to create novel rate control mechanisms.

Gonadal cell surface receptor for plasma retinol-binding protein A method for its radioassay and studies on its level during spermatogenesis

A specific membrane receptor for plasma retinol-binding protein has been demonstrated in testicular cells. Prealbumin-2 did not show any specific binding to the membrane. The affinity of retinol-binding protein for receptor drastically decreases upon delivery of retinol and the retinol-binding protein does not enter the cell. The mechanism of delivery of retinol to the target cell by plasma retinol-binding protein has been investigated. The process involves two steps: direct binding of retinol-binding protein to the receptor and uptake of retinol by the target cell with a concomitant drastic reduction in the affinity of the retinol-binding protein to the receptor. Probably the second step of the process needs a cytosolic factor, possibly the cellular retinol-binding protein or an enzyme.The binding of retinol-binding protein to the receptor is saturable and reverible. The interaction shows a Kd value of 2.1 · 10−10 M. The specific binding of a retinol-binding protein with great affinity has been employed in the development of a method for radioassay of the receptor. The receptor level of the gonadal cell has been found to vary with the stage of differentiation. The receptor concentrations in 11-week-old birds and adult birds are comparable. Testoterone treatment of 11-week-old birds produced a substantial increase in the receptor concentration over control, while the protein content increased marginally, indicating that, probably, synthesis of the receptor is specifically induced by testoterone during spermatogenesis, and the concentration of receptor is relatively higher before the formation of the acrosome.

Kehittämistutkimus: Tieto- ja viestintätekniikkaa kemian opetukseen

The main aim of the present study was to develop information and communication technology (ICT) based chemistry education. The goals for the study were to support meaningful chemistry learning, research-based teaching and diffusion of ICT innovations. These goals were used as guidelines that form the theoretical framework for this study. This Doctoral Dissertation is based on eight-stage research project that included three design researches. These three design researches were scrutinized as separate case studies in which the different cases were formed according to different design teams: i) one researcher was in charge of the design and teachers were involved in the research process, ii) a research group was in charge of the design and students were involved in the research process, and iii) the design was done by student teams, the research was done collaboratively, and the design process was coordinated by a researcher. The research projects were conducted using mixed method approach, which enabled a comprehensive view on education design. In addition, the three central areas of design research: problem analysis, design solution and design process were included in the research, which was guided by the main research questions formed according to these central areas: 1) design solution: what kind of elements are included in ICT-based learning environments that support meaningful chemistry learning and diffusion of innovation, 2) problem analysis: what kind of new possibilities the designed learning environments offer for the support of meaningful chemistry learning, and 3) design process: what kind of opportunities and challenges does collaboration bring to the design of ICT-based learning environments? The main research questions were answered according to the analysis of the survey and observation data, six designed learning environments and ten design narratives from the three case studies. Altogether 139 chemistry teachers and teacher students were involved in the design processes. The data was mainly analysed by methods of qualitative content analysis. The first main result from the study give new information on the meaningful chemistry learning and the elements of ICT-based learning environment that support the diffusion of innovation, which can help in the development of future ICT-education design. When the designed learning environment was examined in the context of chemistry education, it was evident that an ICT-based chemistry learning environment supporting the meaningful learning of chemistry motivates the students and makes the teacher s work easier. In addition, it should enable the simultaneous fulfilment of several pedagogical goals and activate higher-level cognitive processes. The learning environment supporting the diffusion of ICT innovation is suitable for Finnish school environment, based on open source code, and easy to use with quality chemistry content. According to the second main result, new information was acquired about the possibilities of ICT-based learning environments in supporting meaningful chemistry learning. This will help in setting the goals for future ICT education. After the analysis of design solutions and their evaluations, it can be said that ICT enables the recognition of all elements that define learning environments (i.e. didactic, physical, technological and social elements). The research particularly demonstrates the significance of ICT in supporting students motivation and higher-level cognitive processes as well as versatile visualization resources for chemistry that ICT makes possible. In addition, research-based teaching method supports well the diffusion of studied innovation on individual level. The third main result brought out new information on the significance of collaboration in design research, which guides the design of ICT education development. According to the analysis of design narratives, it can be said that collaboration is important in the execution of scientifically reliable design research. It enables comprehensive requirement analysis and multifaceted development, which improves the reliability and validity of the research. At the same time, it sets reliability challenges by complicating documenting and coordination, for example. In addition, a new method for design research was developed. Its aim is to support the execution of complicated collaborative design projects. To increase the reliability and validity of the research, a model theory was used. It enables time-pound documenting and visualization of design decisions that clarify the process. This improves the reliability of the research. The validity of the research is improved by requirement definition through models. This way learning environments that meet the design goals can be constructed. The designed method can be used in education development from comprehensive to higher level. It can be used to recognize the needs of different interest groups and individuals with regard to processes, technology and substance knowledge as well as interfaces and relations between them. The developed method has also commercial potential. It is used to design learning environments for national and international market.

Single‐gate deep level transient spectroscopy technique

A new deep level transient spectroscopy technique is suggested which allows the deep level parameters to be obtained from a single temperature scan. Using large ratio t2/t1 of the measurement gate positions t1 and t2 and analyzing the steep high‐temperature side of the peak, it is demonstrated that the deep level activation energy can be determined with high accuracy.

Effects of temper level on the dependence of fatigue crack growth threshold and crack closure on the prior austenitic grain size

An attempt has been made to systematically investigate the effects of microstructural parameters, such as the prior austenite grain size (PAGS), in influencing the resistance to fatigue crack growth (FCG) in the near-threshold region under three different temper levels in a quenched and tempered high-strength steel. By austenitizing at various temperatures, the PAGS was varied from about 0.7 to 96 μm. The microstructures with these grain sizes were tempered at 200 °C, 400 °C, and 530 °C and tested for fatigue thresholds and crack closure. It has been found that, in general, three different trends in the dependence of both the total threshold stress intensity range, ΔK th , and the intrinsic threshold stress intensity range, ΔK eff, th , on the PAGS are observable. By considering in detail the factors such as cyclic stress-strain behavior, environmental effects on FCG, and embrittlement during tempering, the present observations could be rationalized. The strong dependence of ΔK th and ΔK eff, th on PAGS in microstructures tempered at 530 °C has been primarily attributed to cyclic softening and thereby the strong interaction of the crack tip deformation field with the grain boundary. On the other hand, a less strong dependence of ΔK th and ΔK eff, th on PAGS is suggested to be caused by the cyclic hardening behavior of lightly tempered microstructures occurring in 200 °C temper. In both microstructures, crack closure influenced near-threshold FCG (NTFCG) to a significant extent, and its magnitude was large at large grain sizes. Microstructures tempered at the intermediate temperatures failed to show a systematic variation of ΔKth and ΔKeff, th with PAGS. The mechanisms of intergranular fracture vary between grain sizes in this temper. A transition from “microstructure-sensitive” to “microstructure-insensitive” crack growth has been found to occur when the zone of cyclic deformation at the crack tip becomes more or less equal to PAGS. Detailed observations on fracture morphology and crack paths corroborate the grain size effects on fatigue thresholds and crack closure.

Characterization of defects in gallium arsenide

It is well-known that the properties of semiconductor materials including gallium arsenide are controlled by defects and impurities. The characterization of these defects is important not only for better understanding of the solid state phenomena but also for improved reliability and performance of electronic devices. We have been investigating the defects in gallium arsenide for several years using deep level transient spectroscopy, photoconductivity, transient photoconductivity, photoluminescence etc. Results drawn from our recent studies are presented here to illustrate some of the problems concerning transition metal impurities, process-induced defects, occurrence of intracentre transitions and metastability of deep levels in gallium arsenide.

Composite Performance and Reliability Analysis for Hypercube Systems

In this paper we propose a novel technique to model and ana¿ lyze the performability of parallel and distributed architectures using GSPN-reward models.

Translational Up-Regulation and High-Level Protein Expression from Plasmid Vectors by mTOR Activation via Different Pathways in PC3 and 293T Cells

Background: Though 293T cells are widely used for expression of proteins from transfected plasmid vectors, the molecular basis for the high-level expression is yet to be understood. We recently identified the prostate carcinoma cell line PC3 to be as efficient as 293T in protein expression. This study was undertaken to decipher the molecular basis of high-level expression in these two cell lines. Methodology/Principal Findings: In a survey of different cell lines for efficient expression of platelet-derived growth factor-B (PDGF-B), beta-galactosidase (beta-gal) and green fluorescent protein (GFP) from plasmid vectors, PC3 was found to express at 5-50-fold higher levels compared to the bone metastatic prostate carcinoma cell line PC3BM and many other cell lines. Further, the efficiency of transfection and level of expression of the reporters in PC3 were comparable to that in 293T. Comparative analyses revealed that the high level expression of the reporters in the two cell lines was due to increased translational efficiency. While phosphatidic acid (PA)-mediated activation of mTOR, as revealed by drastic reduction in reporter expression by n-butanol, primarily contributed to the high level expression in PC3, multiple pathways involving PA, PI3K/Akt and ERK1/2 appear to contribute to the abundant reporter expression in 293T. Thus the extent of translational upregulation attained through the concerted activation of mTOR by multiple pathways in 293T could be achieved through its activation primarily by the PA pathway in PC3. Conclusions/Significance: Our studies reveal that the high-level expression of proteins from plasmid vectors is effected by translational up-regulation through mTOR activation via different signaling pathways in the two cell lines and that PC3 is as efficient as 293T for recombinant protein expression. Further, PC3 offers an advantage in that the level of expression of the protein can be regulated by simple addition of n-butanol to the culture medium.

Impact of climate change at species level: a case study of teak in India

In this study, we model the long-term effect of climate change on commercially important teak (Tectona grandis) and its productivity in India. This modelling assessment is based on climate projections of the regional climate model of the Hadley Center (HadRM3) and the dynamic vegetation model, IBIS. According to the model projections, 30% of teak grids in India are vulnerable to climate change under both A2 and B2 SRES scenarios because the future climate may not be optimal for teak at these grids. However, the net primary productivity and biomass are expected to increase because of elevated levels of CO2. Given these directions of likely impacts, it is crucial to further investigate the climate change impacts on teak and incorporate such findings into long-term teak plantation programs. This study also demonstrates the feasibility and limitations of assessing the impact of projected climate change at the species level in the tropics.

V-CE Sensing for IGBT Protection in NPC Three Level Converters-Causes For Spurious Trippings and Their Elimination

Neutral point clamped (NPC), three level converters with insulated gate bipolar transistor devices are very popular in medium voltage, high power applications. DC bus short circuit protection is usually done, using the sensed voltage across collector and emitter (i.e., V-CE sensing), of all the devices in a leg. This feature is accommodated with the conventional gate drive circuits used in the two level converters. The similar gate drive circuit, when adopted for NPC three level converter protection, leads to false V-CE fault signals for inner devices of the leg. The paper explains the detailed circuit behavior and reasons, which result in the occurrence of such false V-CE fault signals. This paper also illustrates that such a phenomenon shows dependence on the power factor of the supplied three-phase load. Finally, experimental results are presented to support the analysis. It is shown that the problem can be avoided by blocking out the V-CE sense fault signals of the inner devices of the leg.

Construction of energy-level diagram of oriented benzene using connectivity information obtained by modified z-cosy experiment

Experiments involving selective perturbation of a transition yield information about the directly connected transitions, which in turn yield information for deriving the parameters of the spin Hamiltonian of oriented molecules. Problems involved with selective perturbation are removed by the use of a two-dimensional experiment, namely, the modified Z-COSY-experiment, The use of this experiment is demonstrated for obtaining the connectivity information and for determining the parameters of the spin Hamiltonian of oriented benzene, a strongly coupled six-spin system