Matriz de Butler de Banda Ancha en Banda X para Antenas Reconfigurables

The work presented in this document shows the complete simulation of a Butler matrix. This circuit will be used in the feeding of a steerable on board antenna in X band. The antenna consists of printed elements grouped in an array. This terminal works in a frequency band from 7.25 up to 8.4 GHz (15% of bandwidth), where both bands, reception (7.25 – 7.75 GHz) and transmission (7.9–8.4 GHz), are included simultaneously. The whole antenna reaches 31 dBi, with a beam width smaller than 10º and a dual circular polarization. This antenna also includes the capability of electronic steering in elevation ±45º and mechanically motorized junction 360º in azimuth.

Electronic Steering antenna onboard for satellite communications in X band.

The antenna presented in this article will be developed for satellite communications onboard systems based on the recommendations ITU-R S.580-6 and ITU-R S.465-5. The antenna consists of printed elements grouped in an array, this terminal works in a frequency band from 7.25 up to 8.4 GHz (14.7% of bandwidth), where both bands, reception (7.25 - 7.75 GHz) and transmission (7.9 - 8.4 GHz), are included simultaneously. The antenna reaches a gain about 31 dBi, and it has a radiation pattern with a beamwidth smaller than 10° and a dual circular polarization. The antenna has the capability to steer in elevation from 90° to 40° electronically and 360° in azimuth with a motorized junction.

Mutual Coupling Reduction Techniques in Electronic Steering Antennas in X Band

This work provides the development of an antenna for satellite communications onboard systems based on the recommendations ITU-R S.580-6 [1] and ITU-R S.465-5 [2]. The antenna consists of printed elements grouped in an array, working in a frequency band from 7.25 up to 8.4 GHz (15% of bandwidth). In this working band, transmission and reception are included simultaneously. The antenna reaches a gain about 31 dBi, has a radiation pattern with a beam width smaller than 10oand dual circular polarization. It has the capability to steer in elevation through a Butler matrix to 45

Ku band transmitarray lens for microwave applications

In this document a microstrip constrained lens device for Ku band, for microwave purpose, is presented. This paper offers an overview of artificial lens-type devices and the proposed transmitarray lens is thoroughly studied in terms of design and manufacturing, with architecture discussion and selection, along with the design, manufacturing and validation of all the forming components of the transmitarray (transmission circuits, radiating elements, etc.). Each element is properly characterized and assembled properly in the complete transmitarray prototype. Eventually, radiation pattern measurements as well as gain and directivity values, are provided to show the proper behaviour of the proposed transmitarray lens.

Dual circular polarized steering antenna for satellite communications in X band

In this work, a dual circular polarized steering antenna for satellite communications in X band is presented. The antenna consists of printed elements grouped in an array. This terminal works in a frequency band from 7.25 GHz up to 8.4 GHz (15% of bandwidth), where both bands, reception (RX) and transmission (TX) are included simultaneously and Left Handed Circular Polarization (LHCP) and Right Handed Circular Polarization (RHCP) are interchangeable. The antenna is compact, narrow bandwidth and reaches a gain of 16 dBi. It has the capability to steer in elevation to 45±, 75±, 105± and 135± electronically with a Butler matrix and 360± in azimuth with a motorized junction.

La co[n]quista del reyno de Nauarra ... / hecha por Luys Correa.

Port. con esc. xil. de Gutierre de Padilla dentro de una orla

Centinela contra iudios puesta en la torre de la Iglesia de Dios / con el trabaio, caudal, y desuelo del P. Fr. Francisco de Torreioncillo, predicador ... de Descalzos de la Regular Obseruancia de nuestro Serafico Padre San Francisco.

Sign.: [calderón]8, A-P8

Mutual coupling reduction using EBG in steering antennas

In this letter, a dual circular polarized steering antenna for satellite communications in X-band is presented. This antenna consists of printed elements grouped in an array, able to work from 7.25 up to 8.4 GHz in both polarizations: left-handed circular polarization (LHCP) and right-handed circular polarization (RHCP). The module antenna is compact, with narrow beamwidth, and reaches a gain of 16 dBi. It has the capability to steer in elevation to and electronically with a Butler matrix. In order to reduce the mutual coupling between adjacent patches, electromagnetic band-gap (EBG) structures are introduced. These EBGs combine double-layer and edge location via in order to reduce the size, without changing the low-permittivity substrate, and therefore maintaining the high radiation efficiency of the antenna.

EBG size reduction for low permittivity substrates

Double layer and edge-location via techniques are combined for electromagnetic band gap (EBG) size reduction. The study of the required number of elements and their dimensions is carried out in order to suppress the surface wave propagation modes and consequently to reduce the mutual coupling between radiating elements in low-permittivity substrates. By applying these techniques, the size of the EBG mushroom is reduced by 30%; however, the bandwidth operation maintains its value, and these structures can be integrated between radiating elements in broad bandwidth antennas.

New EBG solutions for mutual coupling reduction

Electromagnetic Band Gap (EBG) based on Frequency Selective Surfaces (FSS) [1] are one type of metamaterials [2] with electrical properties [3]. This EBG are used in mutual coupling reduction, back lobe radiation reduction, etc. In this work not only new shapes for the mushroom-type are presented, but also multilayered configurations were studied in order to reduce the patch size and the necessary number of elements.

Revision of EBG metamaterials and active antennas

This review of Electromagnetic Band Gap (EGB) metamaterials and steering integrated antennas was carried out in IMST GmbH under a short collaboration stay. This activity is in line with Coordinating the Antenna Research in Europe (CARE). The aim is to identify the newest trends, and suggest novel solutions and design methodologies for various applications.

Sistema para cambiar la geometría de un motor

En este proyecto se desarrolla un sistema electrónico para variar la geometría de un motor de un monoplaza que participa en la competición Fórmula SAE. Fórmula SAE es una competición de diseño de monoplazas para estudiantes, organizado por “Society of Automotive Enginners” (SAE). Este concurso busca la innovación tecnológica de la automoción, así como que estudiantes participen en un trabajo real, en el cual el objetivo es obtener resultados competitivos cumpliendo con una serie de requisitos. La variación de la geometría de un motor en un vehículo permite mejorar el rendimiento del monoplaza consiguiendo elevar el par de potencia del motor. Cualquier mejora en del vehículo en un ámbito de competición puede resultar determinante en el desenlace de la misma. El objetivo del proyecto es realizar esta variación mediante el control de la longitud de los tubos de admisión de aire o “runners” del motor de combustión, empleando un motor lineal paso a paso. A partir de la información obtenida por sensores de revoluciones del motor de combustión y la posición del acelerador se debe controlar la distancia de dichos tubos. Integrando este sistema en el bus CAN del vehículo para que comparta la información medida al resto de módulos. Por todo esto se realiza un estudio aclarando los aspectos generales del objetivo del trabajo, para la comprensión del proyecto a realizar, las posibilidades de realización y adquisición de conocimientos para un mejor desarrollo. Se presenta una solución basada en el control del motor lineal paso a paso mediante el microcontrolador PIC32MX795F512-L. Dispositivo del fabricante Microchip con una arquitectura de 32 bits. Este dispone de un módulo CAN integrado y distintos periféricos que se emplean en la medición de los sensores y actuación sobre el motor paso a paso empleando el driver de Texas Instruments DRV8805. Entonces el trabajo se realiza en dos líneas, una parte software de programación del control del sistema, empleando el software de Microchip MPLABX IDE y otra parte hardware de diseño de una PCB y circuitos acondicionadores para la conexión del microcontrolador, con los sensores, driver, motor paso a paso y bus CAN. El software empleado para la realización de la PCB es Orcad9.2/Layout. Para la evaluación de las medidas obtenidas por los sensores y la comprobación del bus CAN se emplea el kit de desarrollo de Microchip, MCP2515 CAN Bus Monitor Demo Board, que permite ver la información en el bus CAN e introducir tramas al mismo. ABSTRACT. This project develops an electronic system to vary the geometry of a car engine which runs the Formula SAE competition. Formula SAE is a design car competition for students, organized by "Society of Automotive Engineers" (SAE). This competition seeks technological innovation in the automotive industry and brings in students to participate in a real job, in which the objective is to obtain competitive results in compliance with certain requirements. Varying engine’s geometry in a vehicle improves car’s performance raising engine output torque. Any improvement in the vehicle in a competition field can be decisive in the outcome of it. The goal of the project is the variation by controlling the length of the air intake pipe or "runners" in a combustion engine, using a linear motor step. For these, uses the information gathered by speed sensors from the combustion engine and by the throttle position to control the distance of these tubes. This system is integrated in the vehicle CAN bus to share the information with the other modules. For all this is made a study to clarify the general aspects of the project in order to understand the activities developed inside the project, the different options available and also, to acquire knowledge for a better development of the project. The solution is based on linear stepper motor control by the microcontroller PIC32MX795F512-L. Device from manufacturer Microchip with a 32-bit architecture. This module has an integrated CAN various peripherals that are used in measuring the performance of the sensors and drives the stepper motor using Texas Instruments DRV8805 driver. Then the work is done in two lines, first, control programming software system using software MPLABX Microchip IDE and, second, hardware design of a PCB and conditioning circuits for connecting the microcontroller, with sensors, driver stepper motor and CAN bus. The software used to carry out the PCB is Orcad9.2/Layout. For the evaluation of the measurements obtained by the sensors and CAN bus checking is used Microchip development kit, MCP2515 CAN Bus Monitor Demo Board, that allows you to see the information on the CAN bus and enter new frames in the bus.

An initial study on atmospheric pressure ion transport by laser ionization and electrostatic fields.

Laser ionization of mixtures of gases at atmospheric pressure and the subsequent transport through electrostatic field is studied. A prototype is designed to perform the transport and detection of the ions. Relevance of the composition of the mixture of gases and ionization parameters is shown

Nueva tecnología para la separación de gases atmosféricos y captura de dióxido de carbono por aplicación de campos electromagnéticos y fotoionización

Son numerosos los expertos que predicen que hasta pasado 2050 no se utilizarán masivamente las energías de origen renovable, y que por tanto se mantendrá la emisión de dióxido de carbono de forma incontrolada. Entre tanto, y previendo que este tipo de uso se mantenga hasta un horizonte temporal aún más lejano, la captura, concentración y secuestro o reutilización de dióxido de carbono es y será una de las principales soluciones a implantar para paliar el problema medioambiental causado. Sin embargo, las tecnologías existentes y en desarrollo de captura y concentración de este tipo de gas, presentan dos limitaciones: las grandes cantidades de energía que consumen y los grandes volúmenes de sustancias potencialmente dañinas para el medioambiente que producen durante su funcionamiento. Ambas razones hacen que no sean atractivas para su implantación y uso de forma extensiva. La solución planteada en la presente tesis doctoral se caracteriza por la ausencia de residuos producidos en la operación de captura y concentración del dióxido de carbono, por no utilizar substancias químicas y físicas habituales en las técnicas actuales, por disminuir los consumos energéticos al carecer de sistemas móviles y por evitar la regeneración química y física de los materiales utilizados en la actualidad. Así mismo, plantea grandes retos a futuras innovaciones sobre la idea propuesta que busquen fundamentalmente la disminución de la energía utilizada durante su funcionamiento y la optimización de sus componentes principales. Para conseguir el objetivo antes citado, la presente tesis doctoral, una vez establecido el planteamiento del problema al que se busca solución (capítulo 1), del estudio de las técnicas de separación de gases atmosféricos utilizadas en la actualidad, así como del de los sistemas fundamentales de las instalaciones de captura y concentración del dióxido de carbono (capítulo 2) y tras una definición del marco conceptual y teórico (capítulo 3), aborda el diseño de un prototipo de ionización fotónica de los gases atmosféricos para su posterior separación electrostática, a partir del estudio, adaptación y mejora del funcionamiento de los sistemas de espectrometría de masas. Se diseñarán y desarrollarán los sistemas básicos de fotoionización, mediante el uso de fuentes de fotones coherentes, y los de separación electrostática (capítulo 4), en que se basa el funcionamiento de este sistema de separación de gases atmosféricos y de captura y concentración de dióxido de carbono para construir un prototipo a nivel laboratorio. Posteriormente, en el capítulo 5, serán probados utilizando una matriz experimental que cubra los rangos de funcionamiento previstos y aporte suficientes datos experimentales para corregir y desarrollar el marco teórico real, y con los que se pueda establecer y corregir un modelo físico– matemático de simulación (capítulo 6) aplicable a la unidad en su conjunto. Finalmente, debido a la utilización de unidades de ionización fotónica, sistemas láseres intensos y sistemas eléctricos de gran potencia, es preciso analizar el riesgo biológico a las personas y al medioambiente debido al impacto de la radiación electromagnética producida (capítulo 7), minimizando su impacto y cumpliendo con la legislación vigente. En el capítulo 8 se planteará un diseño escalable a tamaño piloto de la nueva tecnología propuesta y sus principales modos de funcionamiento, así como un análisis de viabilidad económica. Como consecuencia de la tesis doctoral propuesta y del desarrollo de la unidad de separación atmosférica y de captura y concentración de dióxido de carbono, surgen diversas posibilidades de estudio que pueden ser objeto de nuevas tesis doctorales y de futuros desarrollos de ingeniería. El capítulo 9 tratará de incidir en estos aspectos indicando líneas de investigación para futuras tesis y desarrollos industriales. ABSTRACT A large number of experts predict that until at least 2050 renewable energy sources will not be massively used, and for that reason, current Primary Energy sources based on extensive use of fossil fuel will be used maintaining out of control emissions, Carbon Dioxide above all. Meanwhile, under this scenario and considering its extension until at least 2050, Carbon Capture, Concentration, Storage and/or Reuse is and will be one of the main solutions to minimise Greenhouse Gasses environmental effect. But, current Carbon Capture and Storage technology state of development has two main problems: it is a too large energy consuming technology and during normal use it produces a large volume of environmentally dangerous substances. Both reasons are limiting its development and its extensive use. This Ph Degree Thesis document proposes a solution to get the expected effect using a new atmospheric gasses separation system with the following characteristics: absence of wastes produced, it needs no chemical and/or physical substances during its operation, it reduces to minimum the internal energy consumptions due to absence of mobile equipment and it does not need any chemical and/or physical regeneration of substances. This system is beyond the State of the Art of current technology development. Additionally, the proposed solution raises huge challenges for future innovations of the proposed idea finding radical reduction of internal energy consumption during functioning, as well as regarding optimisation of main components, systems and modes of operation. To achieve this target, once established the main problem, main challenge and potential solving solutions (Chapter 1), it is established an initial starting point fixing the Atmospheric Gasses Separation and Carbon Capture and Storage developments (Chapter 2), as well as it will be defined the theoretical and basic model, including existing and potential new governing laws and mathematical formulas to control its system functioning (Chapter 3), this document will deal with the design of an installation of an operating system based on photonic ionization of atmospheric gasses to be separated in a later separation system based on the application of electrostatic fields. It will be developed a basic atmospheric gasses ionization prototype based on intense radioactive sources capable to ionize gasses by coherent photonic radiation, and a basic design of electrostatic separation system (Chapter 4). Both basic designs are the core of the proposed technology that separates Atmospheric Gasses and captures and concentrates Carbon Dioxide. Chapter 5 will includes experimental results obtained from an experimental testing matrix covering expected prototype functioning regimes. With the obtained experimental data, theoretical model will be corrected and improved to act as the real physical and mathematical model capable to simulate real system function (Chapter 6). Finally, it is necessary to assess potential biological risk to public and environment due to the proposed use of units of intense energy photonic ionization, by laser beams or by non–coherent sources and large electromagnetic systems with high energy consumption. It is necessary to know the impact in terms of and electromagnetic radiation taking into account National Legislation (Chapter 7). On Chapter 8, an up scaled pilot plant will be established covering main functioning modes and an economic feasibility assessment. As a consequence of this PhD Thesis, a new field of potential researches and new PhD Thesis are opened, as well as future engineering and industrial developments (Chapter 9).