Performance enhancement of large industrial wastewater stabilization ponds

A 6-month-long, bench-scale simulation of an industrial wastewater stabilization pond (WSP) system was conducted to evaluate responses to several potential performance-enhancing treatments. The industrial WSP system consists of an anaerobic primary (1ry) WSP treating high-strength wastewater, followed by facultative secondary (2ry) and aerobic tertiary (3ry) WSPs in series treating lower-strength wastewater. The 1ry WSP was simulated with four glass aquaria which were fed with wastewater from the actual WSP system. The treatments examined were phosphorus supplementation (PHOS), phosphorus supplementation with pH control (PHOS+ALK), and phosphorus supplementation with pH control and effluent recycle (PHOS+ALK+RCY). The supplementary phosphorus treatment alone did not yield any significant change versus the CONTROL 1ry model pond. The average carbon to phosphorus ratio of the feed wastewater received from the WSP system was already 100:0.019 (i.e., 2,100 mg/l: 0.4 mg/l). The pH-control treatments (PHOS+ALK and PHOS+ALK+RCY) produced significant results, with 9 to 12 percent more total organic carbon (TOC) removal, 43 percent more volatile organic acid (VOA) generation, 78 percent more 2-ethoxyethanol and 14 percent more bis(2-chloroethyl)ether removal, and from 100- to 10,000-fold increases in bacterial enzyme activity and heterotrophic bacterial numbers. Recycling a 10-percent portion of the effluent yielded less variability for certain physicochemical parameters in the PHOS+ALK+RCY 1ry model pond, but overall there was no statistically-detectable improvement in performance versus no recycle. The 2ry and 3ry WSPs were also simulated in the laboratory to monitor the effect and fate of increased phosphorus loadings, as might occur if supplemental phosphorus were added to the 1ry WSP. Noticeable increases in algal growth were observed at feed phosphorus concentrations of 0.5 mg/l; however, there were no significant changes in the monitored physicochemical parameters. The effluent phosphorus concentrations from both the 2ry and 3ry model ponds did increase notably when feed phosphorus concentrations were increased from 0.5 to 1.0 mg/l. ^

Bench-scale evaluation of the activated sludge process for treatment of a high -strength chemical plant wastewater

A bench-scale treatability study was conducted on a high-strength wastewater from a chemical plant to develop an alternative for the existing waste stabilization pond treatment system. The objective of this study was to determine the treatability of the wastewater by the activated sludge process and, if treatable, to determine appropriate operating conditions, and to evaluate the degradability of bis(2-chloroethyl)ether (Chlorex) and benzene in the activated sludge system. Four 4-L Plexi-glass, complete mixing, continuous flow activated sludge reactors were operated in parallel under different operating conditions over a 6-month period. The operating conditions examined were hydraulic retention time (HRT), sludge retention time (SRT), nutrient supplement, and Chlorex/benzene spikes. Generally the activated sludge system treating high-strength wastewater was stable under large variations of organic loading and operating conditions. At an HRT of 2 days, more than 90% removal efficiency with good sludge settleability was achieved when the organic loading was less than 0.4 g BOD$\sb5$/g MLVSS/d or 0.8 g COD/g MLVSS/d. At least 20 days of SRT was required to maintain steady operation. Phosphorus addition enhanced the performance of the system especially during stressed operation. On the average, removals of benzene and Chlorex were 73-86% and 37-65%, respectively. In addition, the low-strength wastewater was treatable by activated sludge process, showing more than 90% BOD removal at a HRT of 0.5 days. In general, the sludge had poor settling characteristics. The aerated lagoon process treating high-strength wastewater also provided significant organic reduction, but did not produce an acceptable effluent concentration. ^

Monitoreo de parásitos patógenos en afluentes agroindustriales

Las aguas residuales son potenciales portadoras de enteroparásitos patógenos para el hombre cuya dosis infectiva puede ser mínima y prolongado el tiempo de sobrevivencia de huevos y quistes en el ambiente. La reglamentación limita la presencia de huevos de helmintos y, hasta el año 2000, no proponía una técnica para su detección. Este trabajo se realizó para caracterizar parasitológicamente los efluentes procedentes de agroindustrias. La capacitación en la identificación microscópica demandó la confección de fichas que describen las características de huevos de helmintos. Se efectuaron ensayos con muestras de bodegas y aceiteras en los puntos detectados de contaminación. Los métodos fueron adaptados a las particularidades de los efluentes. Los resultados no señalaron presencia de helmintos; no obstante, se hallaron Cyclospora e Isospora, protozoarios que, por su alto poder infectivo, también constituyen un riesgo para el hombre. Sin embargo, no están contemplados por la legislación. Respecto a helmintos, es necesario un estudio comparativo de las técnicas de detección para efluentes agroindustriales, con el fin de establecer las que optimicen su recuperación. En cuanto a otras especies es preciso continuar investigando su presencia para evaluar la conveniencia de incorporarlas a la reglamentación.

Arum italicum mill (Araceae) : cultivado en Mendoza

Fil: Roig, Fidel Antonio. Universidad Nacional de Cuyo. Facultad de Ciencias Agrarias

Ecotoxicology of pesticides on natural enemies of olive groves. Potential of ecdysone agonists for controlling Bactrocera oleae (Rossi) (Diptera: Tephritidae)

Pesticide applications are still one of the most common control methods against the main olive grove pests and diseases: the olive fruit fly, Bactrocera oleae (Rossi), the olive moth, Prays oleae (Bernard), the black scale, Saissetia oleae (Olivier), and the olive leaf spot, caused by the fungus Spilocaea oleagina Fries. However, and because the new pesticide legislation is aimed at an integrated pest and disease management, it is still important to evaluate and to know the ecotoxicology of pesticides on the natural enemies of the different agrosystems. A part of this work has been focusses on evaluating the direct and indirect effects of kaolin particle films and two copper-based products (Bordeaux mixture and copper oxychloride) through different laboratory, extended laboratory and semi-field experiments. Two natural enemies have been chosen: Psyttalia concolor (Szèpligeti), a parasitoid of the olive fruit fly, and Chilocorus nigritus (F.), predator of Diaspididae. This predator has been used instead of C. bipustulatus (L.), which is the species found in olive orchards. Kaolin mainly acts as a repellent of insects and/or as an oviposition deterrent. It is used in olive groves to control the olive fruit fly and the olive moth. Copper is applied against fungal and bacterial diseases. In olive groves it is used against the olive leaf spot and other diseases. No statistical differences were found in any of the experiments performed, compared to the controls, except when the oral toxicity of the products was evaluated on P. concolor females. In this case, kaolin and copper oxychloride caused a higher mortality 72 hours after the treatments, and both kaolin and the two copper formulations decreased females’ life span. Reproductive parameters were only negatively affected when kaolin was ingested. Apart from these experiments, due to the uncommon mode of action of kaolin, two extra experiments were carried out: a dual choice and a no-choice experiment. In this case, both P. concolor females and C. nigritus adults showed a clear preference for the untreated surfaces when they had the possibility of choosing between a treated surface and an untreated one. When there was no choice, no statistical differences were found between the treatments and the controls. Furthermore, the efficacy and the selectivity of three insect growth regulators (methoxyfenozide, tebufenozide and RH-5849) on B. oleae and P. concolor, respectively, have also been evaluated. In addition to laboratory experiments to evaluate the toxicity of the insecticides, also molecular approaches were used. RNA of both insects was isolated. cDNA was subsequently synthesized and the complete sequences of the ligand biding domain (LBD) of the ecdysone receptor of each insect were then determined. Afterwards the three dimensional structures of both LBDs were constructed. Finally, the docking of the insecticide molecules in the cavity delineated by the 12 α-helix that composed the LBD was performed. Both toxicity assays and molecular docking approaches showed that either methoxyfenozide or tebufenozide had no negative effects nor on B. oleae nor on P. concolor. In contrast, RH-5849 had no deleterious effect to the parasitoid but decreased olive fruit fly adults’ life span, especially when they were in contact with the fresh residue of the insecticide applied on a glass surface. The docking study of RH-5849 molecule has shown a very light hindrance with the wall of the LBD pocket. This means that this molecule could more or less adjust in the cavity. Thus, searching of new insecticides for controlling the olive fruit fly could be based on the basic lead structure of RH-5849 molecule.

Caracterización de la madera de Castanea sativa Mill. de procedencia española

La madera de castaño de procedencia española no está presente como material estructural en la norma europea EN 1912, y por lo tanto no está asignada a ninguna clase resistente como sí lo están otras especies españolas. Por ello, en el presente trabajo se realizó una caracterización de madera aserrada de castaño de Asturias con fines estructurales, realizando los ensayos según la norma UNE EN 408:2004, y calculando sus valores característicos según la norma UNE EN 384:2010. Los valores obtenidos permitieron asignar una clase resistente de las establecidas en la norma UNE EN 338:2010. Fueron evaluadas un total de 260 probetas de dos secciones (40x100 y 40x150 mm) siendo asignada una clase resistente D24, resultando la densidad y la resistencia a flexión los parámetros limitantes y observándose un valor de módulo de elasticidad superior al correspondiente a dicha clase. La relación entre los módulo de elasticidad longitudinal y transversal obtenidos experimentalmente fue de 10 aproximadamente, mientras que la normativa establece, como valor genérico, 16. Se observó que la singularidad de la madera que provocó un mayor porcentaje de rotura fue la presencia de nudos, presentando estas probetas un valor de resistencia significativamente menor. Chestnut timber from Spain is not included as a structural timber in the European standard EN 1912 nor is it assigned to any strength class like other Spanish species. Therefore, a characterization of structural chestnut timber from Asturias was made according to the UNE EN 408:2004, and the characteristic values were calculated according to the UNE EN 384:2010. The values obtained allowed the assignment of a strength class according to UNE EN 338:2010. 260 samples of two sections (40x100 and 40x150 mm) were tested and a D24 strength class was assinged. Density and bending strength were the limiting parameters, and the value of modulus of elasticity was higher than the values asssigned to D24. The relationship between modulus of elasticity and the shear modulus obtained was approximately equal to 10, while this value in the UNE EN 384:2010 is set at 16. The characteristic of the wood which caused a higher percentage of failure was the presence of knots, resulting in significantly lower resistance values.

The water footprint of olives and olive oil in Spain

This paper evaluates the water footprint of Spanish olives and olive oil over the period 1997-2008. In particular, it analyses the three colour components of the water footprint: green (rainwater stored in the soil), blue (surface and groundwater) and grey (freshwater required to assimilate load of pollutants). Apparent water productivity and virtual water embedded in olive oil exports have also been studied. Results show more than 99.5% of the water footprint of one liter of bottled olive oil is related to the olive production, whereas less than 0.5% is due to the other components such as bottle, cap and label. Over the studied period, the green water footprint in absolute terms of Spanish olive oil production represents about 72% in rainfed systems and just 12% in irrigated olive orchards. Blue and grey water footprints represent 6% and 10% of the national water footprint, respectively. It is shown that olive production is concentrated in regions with the smallest water footprint per unit of product. However, the increase of groundwater consumption in the main olive producing region (Andalusia), from 98 to 378 Mm3 between 1997 and 2008, has added significant pressure in the upstream Guadalquivir basin. This raises questions about the sustainability of irrigated olive orchards for export from the region. Finally, the virtual water related to olive oil exports illustrate the importance of green water footprint of rainfed olives amounting to about 77% of the total virtual water exports.

Determination of the mechanical properties of corn grains and olive fruits required in DEM simulations

Discrete element method (DEM) is a numerical technique widely used for simulating the mechanical behavior of granular materials involved in many food and agricultural industry processes. Additionally, this technique is also a powerful tool to understand many complex phenomena related to the mechanics of granular materials. However, to make use of the potential of this technique it is necessary to develop DEM models capable of representing accurately the reality. For that, among some other questions, it is essential that the values of the microscopic material properties used to define the numerical model are accurately determined.

Canopy fruit location can affect olive oil quality in Arbequina hedgerow orchards

The effect of location of fruit in canopies of hedgerow olive trees (Olea europaea L., cv. ‘Arbequina’) on quality of virgin oil was tested by analyzing oils extracted from different height layers and faces of 9 olive hedgerows (6 North-South oriented and 3 East-West). Although sensory attributes were not different other oil quality parameters may be significantly modified by fruit position. In some hedgerows, oils extracted from fruits harvested from higher layers exhibited significantly higher stability against oxidation, along with higher palmitic acid, linoleic acid and phenol contents, but lower oleic acid content. Oils extracted from fruits harvested from East and North facing hedgerows oriented North-South and East-West, respectively, exhibited higher oleic contents and lower saturated and polyunsaturated fatty acid contents. The mean phenol content of oils extracted from fruits from a North-South oriented hedgerow was significantly greater from one of the East-West oriented hedgerows. These findings may be relevant for the design of future olive hedgerows destined for olive oil production.

Summer deficit irrigation strategies in hedgerow olive orchard cv. ‘Arbequina’: Effect on fruit characteristics and yield.

Maximum production in hedgerow olive orchards is likely not achieved with maximum evapotranspiration over the long-term. Thus, regulated deficit irrigation (RDI) should be considered as a management option. Four irrigation treatments were evaluated during the summer when olive is most drought resistant. Control (CON) was irrigated to maintain the rootzone close to field capacity. Severe water deficit was applied by irrigating 30% CON from end of fruit drop to end July (DI-J) and from end July until beginning of oil synthesis (DI-A). Less severe water deficit was applied during July and August (DI-JA) by irrigating 50% CON. Flowering, fruiting, abscission, fruit development, fresh and dry weight of fruits, and oil production were evaluated. There were not significant differences in number of buds initiated, number of fruits per inflorescence and fruit drop. Oil production was significantly different between irrigation treatments in all experimental years. CON produced more oil and fruit with higher oil% than DI-A and DI-JA. Oil production of DI-J was not significantly reduced compared to CON and oil% was greater. DI-J was the most effective RDI strategy; with 16% less applied water relative to CON average loss in oil production of 8% was not significantly different to CON. While DI-JA saved most water (27%), oil production was reduced by 15%. Greatest loss in oil production (21%) was observed in DI-A with water saving of 22%.