Learning Robot Motions from Visual Sensing

Learning from demonstration becomes increasingly popular as an efficient way of robot programming. Not only a scientific interest acts as an inspiration in this case but also the possibility of producing the machines that would find application in different areas of life: robots helping with daily routine at home, high performance automata in industries or friendly toys for children. One way to teach a robot to fulfill complex tasks is to start with simple training exercises, combining them to form more difficult behavior. The objective of the Master’s thesis work was to study robot programming with visual input. Dynamic movement primitives (DMPs) were chosen as a tool for motion learning and generation. Assuming a movement to be a spring system influenced by an external force, making this system move, DMPs represent the motion as a set of non-linear differential equations. During the experiments the properties of DMP, such as temporal and spacial invariance, were examined. The effect of the DMP parameters, including spring coefficient, damping factor, temporal scaling, on the trajectory generated were studied.

Characteristics of pyridine adsorption on Au(111) and Au(210) by EIS parameters fitting procedure

Some aspects of the application of electrochemical impedance spectroscopy to studies of solid electrode / solution interface, in the absence of faradaic processes, are analysed. In order to perform this analysis, gold electrodes with (111) and (210) crystallographic orientations in an aqueous solution containing 10 mmol dm-3 KF, as supporting electrolyte, and a pyridine concentration varying from 0.01 to 4.6 mmol dm-3, were used. The experimental data was analysed by using EQUIVCRT software, which utilises non-linear least squares routines, attributing to the solid electrode / solution interface behaviour described by an equivalent circuit with a resistance in series with a constant phase element. The results of this fitting procedure were analysed by the dependence on the electrode potential on two parameters: the pre-exponential factor, Y0, and the exponent n f, related with the phase angle shift. By this analysis it was possible to observe that the pyridine adsorption is strongly affected by the crystallographic orientation of the electrode surface and that the extent of deviation from ideal capacitive behaviour is mainly of interfacial origin.

Harustetun 110 kV kannatuspylvään konseptin kehittäminen

Diplomityössä kehitettiin harustetun 110 kV kannatuspylvään konsepti tuotteeksi. Pylväs on säänkestävästä teräksestä valmistettu putkipalkkirakenteinen I-pylväs. Tavoitteena oli suunnitella rakenteesta kokonaistaloudellisesti edullinen. Rakenteen suunnittelussa otettiin huomioon valmistus-, kuljetus- ja varastointi- sekä rakentamisnäkökohtia. Työssä perehdyttiin pylväsrakenteiden yksityiskohtiin, putkipalkkien liitosmenetelmiin ja pylvään jalan nivelöintiratkaisuihin. Säänkestävä rakennemateriaali otettiin huomioon rakennesuunnittelussa. Rakenteen lujuusteknisen suunnittelun apuna käytettiin epälineaarista elementtimenetelmää. Pylväsrakenteen käyttäytyminen mallinnettiin geometrisesti epälineaariseksi, ja liitosdetaljien analysointia varten kehitettiin epälineaarisia materiaalimalleja. Rakenteen värähtelykäyttäytyminen analysoitiin myös elementtimenetelmällä. Lopputuloksena saatiin aikaan pylväs, joka täyttää sille asetetut vaatimukset. Pylväs on helposti valmistettava, kuljetettava ja pystytettävä.

On convergence of transforms based on parabolic scaling

This thesis studies properties of transforms based on parabolic scaling, like Curvelet-, Contourlet-, Shearlet- and Hart-Smith-transform. Essentially, two di erent questions are considered: How these transforms can characterize H older regularity and how non-linear approximation of a piecewise smooth function converges. In study of Hölder regularities, several theorems that relate regularity of a function f : R2 → R to decay properties of its transform are presented. Of particular interest is the case where a function has lower regularity along some line segment than elsewhere. Theorems that give estimates for direction and location of this line, and regularity of the function are presented. Numerical demonstrations suggest also that similar theorems would hold for more general shape of segment of low regularity. Theorems related to uniform and pointwise Hölder regularity are presented as well. Although none of the theorems presented give full characterization of regularity, the su cient and necessary conditions are very similar. Another theme of the thesis is the study of convergence of non-linear M ─term approximation of functions that have discontinuous on some curves and otherwise are smooth. With particular smoothness assumptions, it is well known that squared L2 approximation error is O(M-2(logM)3) for curvelet, shearlet or contourlet bases. Here it is shown that assuming higher smoothness properties, the log-factor can be removed, even if the function still is discontinuous.

SME internationalisation from a network perspective : an empirical study on a Finnish-Greek business network

The study examines the internationalisation process of a contemporary SME firm and explores the impact of its business network on this development. The objective of the study is to understand SME internationalisation and its dynamics from a network perspective. The purpose of this research project is to describe and explore the development process of a firm and its business network by identifying the changes, critical events and influence factors that form this development. It is a qualitative case study, which focuses on a Finnish focal firm and its respective business network as it expands into the Greek market. It is a longitudinal research process, which covers a period of time from 1994 to 2004. The empirical study concentrates on the paper trading and converting business. The study builds on the network theory and the framework provided by Johanson and Mattsson's (1988) model on network internationalisation. The incremental internationalisation theories and network theories form the theoretical focus. The research project is organised according to a process view. The focal firm evolves from a domestically-oriented small subsidiary into an internationally experienced company, which has activities in several market areas and numerous business networks in various market segments and product categories. The findings illustrate the importance of both the domestic and foreign business network context in a firm's internationalisation process. The results of the study suggest theoretical modifications on a firm's internationalisation process by broadening the perspective and incorporating the strategic context of a firm. The findings suggest that internationalisation process is a non-linear process, which does not have a deterministic order in its development. The findings emphasise the significance of relational networks, both managerial and entrepreneurial, for establishing position in foreign markets. It implies that a firm's evolution is significantly influenced by its business network and by critical events. Business networks gain coherence due to common goals and they use accumulated capabilities to exploit market opportunities. The business network sets constraints and provides opportunities, which makes the related decision making strategically important. The firm co-evolves with its business network. The research project provides an instrumental case study with a description of an SME internationalisation process. It contributes to existing knowledge by illustrating dynamics in an international business network and by pinpointing the importance of suppliers, customers, partners, ownerships and competition to the internationalisation process.

Modeling of electrolyte sorption – from phase equilibria to dynamic separation systems

In this thesis, general approach is devised to model electrolyte sorption from aqueous solutions on solid materials. Electrolyte sorption is often considered as unwanted phenomenon in ion exchange and its potential as an independent separation method has not been fully explored. The solid sorbents studied here are porous and non-porous organic or inorganic materials with or without specific functional groups attached on the solid matrix. Accordingly, the sorption mechanisms include physical adsorption, chemisorption on the functional groups and partition restricted by electrostatic or steric factors. The model is tested in four Cases Studies dealing with chelating adsorption of transition metal mixtures, physical adsorption of metal and metalloid complexes from chloride solutions, size exclusion of electrolytes in nano-porous materials and electrolyte exclusion of electrolyte/non-electrolyte mixtures. The model parameters are estimated using experimental data from equilibrium and batch kinetic measurements, and they are used to simulate actual single-column fixed-bed separations. Phase equilibrium between the solution and solid phases is described using thermodynamic Gibbs-Donnan model and various adsorption models depending on the properties of the sorbent. The 3-dimensional thermodynamic approach is used for volume sorption in gel-type ion exchangers and in nano-porous adsorbents, and satisfactory correlation is obtained provided that both mixing and exclusion effects are adequately taken into account. 2-Dimensional surface adsorption models are successfully applied to physical adsorption of complex species and to chelating adsorption of transition metal salts. In the latter case, comparison is also made with complex formation models. Results of the mass transport studies show that uptake rates even in a competitive high-affinity system can be described by constant diffusion coefficients, when the adsorbent structure and the phase equilibrium conditions are adequately included in the model. Furthermore, a simplified solution based on the linear driving force approximation and the shrinking-core model is developed for very non-linear adsorption systems. In each Case Study, the actual separation is carried out batch-wise in fixed-beds and the experimental data are simulated/correlated using the parameters derived from equilibrium and kinetic data. Good agreement between the calculated and experimental break-through curves is usually obtained indicating that the proposed approach is useful in systems, which at first sight are very different. For example, the important improvement in copper separation from concentrated zinc sulfate solution at elevated temperatures can be correctly predicted by the model. In some cases, however, re-adjustment of model parameters is needed due to e.g. high solution viscosity.

Temporal variability of soil CO2 emission after conventional and reduced tillage described by an exponential decay in time model

To study Assessing the impact of tillage practices on soil carbon losses dependents it is necessary to describe the temporal variability of soil CO2 emission after tillage. It has been argued that large amounts of CO2 emitted after tillage may serve as an indicator for longer-term changes in soil carbon stocks. Here we present a two-step function model based on soil temperature and soil moisture including an exponential decay in time component that is efficient in fitting intermediate-term emission after disk plow followed by a leveling harrow (conventional), and chisel plow coupled with a roller for clod breaking (reduced) tillage. Emission after reduced tillage was described using a non-linear estimator with determination coefficient (R²) as high as 0.98. Results indicate that when emission after tillage is addressed it is important to consider an exponential decay in time in order to predict the impact of tillage in short-term emissions.

Impact of elevated temperature scenarios on potato leaf development

The objective of this study was to simulate the impact of elevated temperature scenarios on leaf development of potato in Santa Maria, RS, Brazil. Leaf appearance was estimated using a multiplicative model that has a non-linear temperature response function which calculates the daily leaf appearance rate (LAR, leaves day-1) and the accumulated number of leaves (LN) from crop emergence to the appearance of the upper last leaf. Leaf appearance was estimated during 100 years in the following scenarios: current climate, +1 °C, +2 °C, +3 °C, +4 °C e +5 °C. The LAR model was estimated with coefficients of the Asterix cultivar in five emergence dates and in two growing seasons (Fall and Spring). Variable of interest was the duration (days) of the crop emergence to the appearance of the final leaf number (EM-FLN) phase. Statistical analysis was performed assuming a three-factorial experiment, with main effects being climate scenarios, growing seasons, and emergence dates in a completely randomized design using years (one hundred) as replications. The results showed that warmer scenarios lead to an increase, in the fall, and a decrease, in the spring growing season, in the duration of the leaf appearance phase, indicating high vulnerability and complexity of the response of potato crop grown in a Subtropical environment to climate change.

Water distribuition characteristics and soil loss of LEPA Quad-Spray emitter nozzles

The objective of this study was to characterize water application rate, water application pattern width, flow rate, water distribution uniformity and soil loss caused by nozzles of the Low Energy Precision Aplication (LEPA) type Quad-Spray emitter. The study was carried out at the Hydraulic and Irrigation Laboratory of the Department of Engineering at the Federal University of Lavras, in Lavras, state of Minas Gerais - MG, Brazil. Twenty-two (22) LEPA Quad-Spray emitter nozzles were evaluated, with nozzle diameter ranging from 1.59 to 9.92 mm. The experimental design used was entirely randomized, with three replications.Increasing values of nozzle flow rate ranging from 77.44 up to 3,044 L h-1, were obtained with increasing nozzle diameter sizes. Application pattern width ranged from 0.56 up to 3.24m, according to nozzles diameter size. Low values of CDU (maximum of 35.73%) were observed when using the Quad-Spray nozzles. Observed average water application rates covered the range between 68.05 mm h-1 (the lowest value that was obtained with the 2.38mm nozzle) and 258.15 mm h-1 (the highest value that was observed with the 9.92 mm). Average water application rates increased in a simple non-linear function with the increase of nozzle size diameter. However, the weighted average increase in the amount of soil loss by erosion was not related to the increase of weighted average water application values.

Creating possibilities for collective creativity : Brokerage Functions in Practice-Based Innovation

In the network era, creative achievements like innovations are more and more often created in interaction among different actors. The complexity of today‘s problems transcends the individual human mind, requiring not only individual but also collective creativity. In collective creativity, it is impossible to trace the source of new ideas to an individual. Instead, creative activity emerges from the collaboration and contribution of many individuals, thereby blurring the contribution of specific individuals in creating ideas. Collective creativity is often associated with diversity of knowledge, skills, experiences and perspectives. Collaboration between diverse actors thus triggers creativity and gives possibilities for collective creativity. This dissertation investigates collective creativity in the context of practice-based innovation. Practice-based innovation processes are triggered by problem setting in a practical context and conducted in non-linear processes utilising scientific and practical knowledge production and creation in cross-disciplinary innovation networks. In these networks diversity or distances between innovation actors are essential. Innovation potential may be found in exploiting different kinds of distances. This dissertation presents different kinds of distances, such as cognitive, functional and organisational which could be considered as sources of creativity and thus innovation. However, formation and functioning of these kinds of innovation networks can be problematic. Distances between innovating actors may be so great that a special interpretation function is needed – that is, brokerage. This dissertation defines factors that enhance collective creativity in practice-based innovation and especially in the fuzzy front end phase of innovation processes. The first objective of this dissertation is to study individual and collective creativity at the employee level and identify those factors that support individual and collective creativity in the organisation. The second objective is to study how organisations use external knowledge to support collective creativity in their innovation processes in open multi-actor innovation. The third objective is to define how brokerage functions create possibilities for collective creativity especially in the context of practice-based innovation. The research objectives have been studied through five substudies using a case-study strategy. Each substudy highlights various aspects of creativity and collective creativity. The empirical data consist of materials from innovation projects arranged in the Lahti region, Finland, or materials from the development of innovation methods in the Lahti region. The Lahti region has been chosen as the research context because the innovation policy of the region emphasises especially the promotion of practice-based innovations. The results of this dissertation indicate that all possibilities of collective creativity are not utilised in internal operations of organisations. The dissertation introduces several factors that could support collective creativity in organisations. However, creativity as a social construct is understood and experienced differently in different organisations, and these differences should be taken into account when supporting creativity in organisations. The increasing complexity of most potential innovations requires collaborative creative efforts that often exceed the boundaries of the organisation and call for the involvement of external expertise. In practice-based innovation different distances are considered as sources of creativity. This dissertation gives practical implications on how it is possible to exploit different kinds of distances knowingly. It underlines especially the importance of brokerage functions in open, practice-based innovation in order to create possibilities for collective creativity. As a contribution of this dissertation, a model of brokerage functions in practice-based innovation is formulated. According to the model, the results and success of brokerage functions are based on the context of brokerage as well as the roles, tasks, skills and capabilities of brokers. The brokerage functions in practice-based innovation are also possible to divide into social and cognitive brokerage.

Structural and operational optimisation : applications in energy systems

In this work mathematical programming models for structural and operational optimisation of energy systems are developed and applied to a selection of energy technology problems. The studied cases are taken from industrial processes and from large regional energy distribution systems. The models are based on Mixed Integer Linear Programming (MILP), Mixed Integer Non-Linear Programming (MINLP) and on a hybrid approach of a combination of Non-Linear Programming (NLP) and Genetic Algorithms (GA). The optimisation of the structure and operation of energy systems in urban regions is treated in the work. Firstly, distributed energy systems (DES) with different energy conversion units and annual variations of consumer heating and electricity demands are considered. Secondly, district cooling systems (DCS) with cooling demands for a large number of consumers are studied, with respect to a long term planning perspective regarding to given predictions of the consumer cooling demand development in a region. The work comprises also the development of applications for heat recovery systems (HRS), where paper machine dryer section HRS is taken as an illustrative example. The heat sources in these systems are moist air streams. Models are developed for different types of equipment price functions. The approach is based on partitioning of the overall temperature range of the system into a number of temperature intervals in order to take into account the strong nonlinearities due to condensation in the heat recovery exchangers. The influence of parameter variations on the solutions of heat recovery systems is analysed firstly by varying cost factors and secondly by varying process parameters. Point-optimal solutions by a fixed parameter approach are compared to robust solutions with given parameter variation ranges. In the work enhanced utilisation of excess heat in heat recovery systems with impingement drying, electricity generation with low grade excess heat and the use of absorption heat transformers to elevate a stream temperature above the excess heat temperature are also studied.

Introduction of the T-10 static line parachuting capability to the NH90 helicopter

The purpose of this study was to investigate the suitability of the Finnish Defence Forces’ NH90 helicopter for parachuting operations with the T-10 static line parachute system. The work was based on the Army Command’s need to compensate for the reduction in the outsourced flight hours for the military static line parachuting training. The aim of the research was to find out the procedures and limitations with which the NH90 IOC+ or FOC version helicopter could be used for static line parachutist training with the T-10B/MC1-1C parachutes. The research area was highly complicated and non-linear. Thus analytical methods could not be applied with sufficient confidence, even with present-day computing power. Therefore an empirical research method was selected, concentrating on flight testing supported with literature study and some calculated estimations. During three flights and 4.5 flight hours in Utti, Finland on 1720 September 2012, a total of 44 parachute drops were made. These consisted of 16 dummy drops and 28 paratrooper jumps. The test results showed that when equipped with the floor mounted PASI-1 anchor line, the deflector bar of the NHIndustries’ Parachuting Kit and Patria’s floor protection panels the Finnish NH90 variant could be safely used for T-10B/MC1-1C static line parachuting operations from the right cabin door at airspeed range of 5080 KIAS (90–150 km/h). The ceiling mounted anchor lines of the NHI’s Parachuting Kit were not usable with the T-10 system. This was due to the static lines’ unsafe behaviour in slipstream when connected to the cabin ceiling level. In conclusion, the NH90 helicopter can be used to meet the Army Command’s requirement for an additional platform for T-10 static line parachutist training. Material dropping, the effect of additional equipment and jumping from the rear ramp should be further studied.

Application of a Pid+fuzzy controller on the motion control system in machine tools

This work deals with an hybrid PID+fuzzy logic controller applied to control the machine tool biaxial table motions. The non-linear model includes backlash and the axis elasticity. Two PID controllers do the primary table control. A third PID+fuzzy controller has a cross coupled structure whose function is to minimise the trajectory contour errors. Once with the three PID controllers tuned, the system is simulated with and without the third controller. The responses results are plotted and compared to analyse the effectiveness of this hybrid controller over the system. They show that the proposed methodology reduces the contour error in a proportion of 70:1.

Rocket tracking and decoupling eigenstructure control law

A control law was designed for a satellite launcher ( rocket ) vehicle using eigenstructure assignment in order that the vehicle tracks a reference attitude and also to decouple the yaw response from roll and pitch manoeuvres and to decouple the pitch response from roll and yaw manoeuvres. The design was based on a complete linear coupled model obtained from the complete vehicle non linear model by linearization at each trajectory point. After all, the design was assessed with the vehicle time varying non-linear model showing a good performance and robustness. The used design method is explained and a case study for the Brazilian satellite launcher ( VLS Rocket ) is reported.

Contact with friction using the augmented Lagrangian Method: a conditional constrained minimization problem

This work presents a formulation of the contact with friction between elastic bodies. This is a non linear problem due to unilateral constraints (inter-penetration of bodies) and friction. The solution of this problem can be found using optimization concepts, modelling the problem as a constrained minimization problem. The Finite Element Method is used to construct approximation spaces. The minimization problem has the total potential energy of the elastic bodies as the objective function, the non-inter-penetration conditions are represented by inequality constraints, and equality constraints are used to deal with the friction. Due to the presence of two friction conditions (stick and slip), specific equality constraints are present or not according to the current condition. Since the Coulomb friction condition depends on the normal and tangential contact stresses related to the constraints of the problem, it is devised a conditional dependent constrained minimization problem. An Augmented Lagrangian Method for constrained minimization is employed to solve this problem. This method, when applied to a contact problem, presents Lagrange Multipliers which have the physical meaning of contact forces. This fact allows to check the friction condition at each iteration. These concepts make possible to devise a computational scheme which lead to good numerical results.