Optimal Controller Designs for Rotating Machines - Penalising the Rate of Change of Control Forcing

In the context of active control of rotating machines, standard optimal controller methods enable a trade-off to be made between (weighted) mean-square vibrations and (weighted) mean-square currents injected into magnetic bearings. One shortcoming of such controllers is that no concern is devoted to the voltages required. In practice, the voltage available imposes a strict limitation on the maximum possible rate of change of control force (force slew rate). This paper removes the aforementioned existing shortcomings of traditional optimal control.

Comparação do controle do inversor trifásico conectado à rede com filtro LCL considerando o amortecimento passivo e ativo

Distributed generation systems must fulfill standards specifications of current harmonics injected to the grid. In order to satisfy these grid requirements, passive filters are connected between inverter and grid. This work compares the characteristic response of the traditional inductive (L) filter with the inductive-capacitive-inductive (LCL) filter. It is shown that increasing the inductance L leads to a good ripple current suppression around the inverter switching frequency. The LCL filter provides better harmonic attenuation and reduces the filter size. The main drawback is the LCL filter impedance, which is characterized by a typical resonance peak, which must be damped to avoid instability. Passive or active techniques can be used to damp the LCL resonance. To address this issue, this dissertation presents a comparison of current control for PV grid-tied inverters with L filter and LCL filter and also discuss the use of active and passive damping for different regions of resonance frequency. From the mathematical models, a design methodology of the controllers was developed and the dynamic behavior of the system operating in closed loop was investigated. To validate the studies developed during this work, experimental results are presented using a three-phase 5kW experimental platform. The main components and their functions are discussed in this work. Experimental results are given to support the theoretical analysis and to illustrate the performance of grid-connected PV inverter system. It is shown that the resonant frequency of the system, and sampling frequency can be associated in order to calculate a critical frequency, below which is essential to perform the damping of the LCL filter. Also, the experimental results show that the active buffer per virtual resistor, although with a simple development, is effective to damp the resonance of the LCL filter and allow the system to operate stable within predetermined parameters.

Análise e proposição de estratégias de estimação e controle de velocidade para motores de indução trifásicos

This study presents a proposal of speed servomechanisms without the use of mechanical sensors (sensorless) using induction motors. A comparison is performed and propose techniques for pet rotor speed, analyzing performance in different conditions of speed and load. For the determination of control technique, initially, is performed an analysis of the technical literature of the main control and speed estimation used, with their characteristics and limitations. The proposed technique for servo sensorless speed induction motor uses indirect field-oriented control (IFOC), composed of four controllers of the proportional-integral type (PI): rotor flux controller, speed controller and current controllers in the direct and quadrature shaft. As the main focus of the work is in the speed control loop was implemented in Matlab the recursive least squares algorithm (RLS) for identification of mechanical parameters, such as moment of inertia and friction coefficient. Thus, the speed of outer loop controller gains can be self adjusted to compensate for any changes in the mechanical parameters. For speed estimation techniques are analyzed: MRAS by rotóricos fluxes MRAS by counter EMF, MRAS by instantaneous reactive power, slip, locked loop phase (PLL) and sliding mode. A proposition of estimation in sliding mode based on speed, which is performed a change in rotor flux observer structure is displayed. To evaluate the techniques are performed theoretical analyzes in Matlab simulation environment and experimental platform in electrical machinery drives. The DSP TMS320F28069 was used for experimental implementation of speed estimation techniques and check the performance of the same in a wide speed range, including load insertion. From this analysis is carried out to implement closed-loop control of sensorless speed IFOC structure. The results demonstrated the real possibility of replacing mechanical sensors for estimation techniques proposed and analyzed. Among these, the estimator based on PLL demonstrated the best performance in various conditions, while the technique based on sliding mode has good capacity estimation in steady state and robustness to parametric variations.

Arquitetura híbrida com DSP e FPGA para implementação de controladores de filtros ativos de potência

The presence of non-linear loads at a point in the distribution system may deform voltage waveform due to the consumption of non-sinusoidal currents. The use of active power filters allows significant reduction of the harmonic content in the supply current. However, the processing of digital control structures for these filters may require high performance hardware, particularly for reference currents calculation. This work describes the development of hardware structures with high processing capability for application in active power filters. In this sense, it considers an architecture that allows parallel processing using programmable logic devices. The developed structure uses a hybrid model using a DSP and an FPGA. The DSP is used for the acquisition of current and voltage signals, calculation of fundamental current related controllers and PWM generation. The FPGA is used for intensive signal processing, such as the harmonic compensators. In this way, from the experimental analysis, significant reductions of the processing time are achieved when compared to traditional approaches using only DSP. The experimental results validate the designed structure and these results are compared with other ones from architectures reported in the literature.

APIs de seguridad en .NET Framework

Este trabajo hace un estudio de algunas de las herramientas de seguridad disponibles en .Net Framework así como la forma de usarlas en un desarrollo web bajo la metodología de desarrollo de ASP.NET siguiendo el modelo Vista-Controlador y usando como entorno de desarrollo Visual Studio. Además de repasar las herramientas disponibles y la forma de uso se ha desarrollado también una aplicación de ejemplo: ItemCoteca-Web; en la que se demuestra cómo resolver el registro de usuarios, la autenticación y autorización de forma segura. En paralelo se ha implementado un cliente Android: Itemcoteca-app que realiza autenticación, registro y dispone de un chat seguro de incidencias para hablar con administradores OnlineEste trabajo no solo presenta las APIs disponibles sino también las buenas prácticas que define Microsoft para el uso de sus herramientas. En particular nos centramos en los tres tipos de controladores que podemos encontrar en una aplicación web Asp.net que son Controllers, WebApi y SignalR, comentando sus diferencias y su uso para clientes Web y móviles.

Performance Analysis of IP based WSNs in real time systems

Wireless sensor networks (WSNs) are the key enablers of the internet of things (IoT) paradigm. Traditionally, sensor network research has been to be unlike the internet, motivated by power and device constraints. The IETF 6LoWPAN draft standard changes this, defining how IPv6 packets can be efficiently transmitted over IEEE 802.15.4 radio links. Due to this 6LoWPAN technology, low power, low cost micro- controllers can be connected to the internet forming what is known as the wireless embedded internet. Another IETF recommendation, CoAP allows these devices to communicate interactively over the internet. The integration of such tiny, ubiquitous electronic devices to the internet enables interesting real-time applications. This thesis work attempts to evaluate the performance of a stack consisting of CoAP and 6LoWPAN over the IEEE 802.15.4 radio link using the Contiki OS and Cooja simulator, along with the CoAP framework Californium (Cf). Ultimately, the implementation of this stack on real hardware is carried out using a raspberry pi as a border router with T-mote sky sensors as slip radios and CoAP servers relaying temperature and humidity data. The reliability of the stack was also demonstrated during scalability analysis conducted on the physical deployment. The interoperability is ensured by connecting the WSN to the global internet using different hardware platforms supported by Contiki and without the use of specialized gateways commonly found in non IP based networks. This work therefore developed and demonstrated a heterogeneous wireless sensor network stack, which is IP based and conducted performance analysis of the stack, both in terms of simulations and real hardware.

Mécanismes psychophysiques et neuronaux de la compensation dynamique de multiples champs de force : facilitation et anticipation liée à des indices de couleur

Dans cette thèse, nous abordons le contrôle moteur du mouvement du coude à travers deux approches expérimentales : une première étude psychophysique a été effectuée chez les sujets humains, et une seconde implique des enregistrements neurophysiologiques chez le singe. Nous avons recensé plusieurs aspects non résolus jusqu’à présent dans l’apprentissage moteur, particulièrement concernant l’interférence survenant lors de l’adaptation à deux ou plusieurs champs de force anti-corrélés. Nous avons conçu un paradigme où des stimuli de couleur aident les sujets à prédire la nature du champ de force externe actuel avant qu’ils ne l’expérimentent physiquement durant des mouvements d’atteinte. Ces connaissances contextuelles faciliteraient l’adaptation à des champs de forces en diminuant l’interférence. Selon le modèle computationnel de l’apprentissage moteur MOSAIC (MOdular Selection And Identification model for Control), les stimuli de couleur aident les sujets à former « un modèle interne » de chaque champ de forces, à s’en rappeler et à faire la transition entre deux champs de force différents, sans interférence. Dans l’expérience psychophysique, quatre groupes de sujets humains ont exécuté des mouvements de flexion/extension du coude contre deux champs de forces. Chaque force visqueuse était associée à une couleur de l’écran de l’ordinateur et les deux forces étaient anti-corrélées : une force résistante (Vr) a été associée à la couleur rouge de l’écran et l’autre, assistante (Va), à la couleur verte de l’écran. Les deux premiers groupes de sujets étaient des groupes témoins : la couleur de l’écran changeait à chaque bloc de 4 essais, tandis que le champ de force ne changeait pas. Les sujets du groupe témoin Va ne rencontraient que la force assistante Va et les sujets du groupe témoin Vr performaient leurs mouvements uniquement contre une force résistante Vr. Ainsi, dans ces deux groupes témoins, les stimuli de couleur n’étaient pas pertinents pour adapter le mouvement et les sujets ne s’adaptaient qu’à une seule force (Va ou Vr). Dans les deux groupes expérimentaux, cependant, les sujets expérimentaient deux champs de forces différents dans les différents blocs d’essais (4 par bloc), associés à ces couleurs. Dans le premier groupe expérimental (groupe « indice certain », IC), la relation entre le champ de force et le stimulus (couleur de l’écran) était constante. La couleur rouge signalait toujours la force Vr tandis que la force Va était signalée par la couleur verte. L’adaptation aux deux forces anti-corrélées pour le groupe IC s’est avérée significative au cours des 10 jours d’entraînement et leurs mouvements étaient presque aussi bien ajustés que ceux des deux groupes témoins qui n’avaient expérimenté qu’une seule des deux forces. De plus, les sujets du groupe IC ont rapidement démontré des changements adaptatifs prédictifs dans leurs sorties motrices à chaque changement de couleur de l’écran, et ceci même durant leur première journée d’entraînement. Ceci démontre qu’ils pouvaient utiliser les stimuli de couleur afin de se rappeler de la commande motrice adéquate. Dans le deuxième groupe expérimental, la couleur de l’écran changeait régulièrement de vert à rouge à chaque transition de blocs d’essais, mais le changement des champs de forces était randomisé par rapport aux changements de couleur (groupe « indice-incertain », II). Ces sujets ont pris plus de temps à s’adapter aux champs de forces que les 3 autres groupes et ne pouvaient pas utiliser les stimuli de couleurs, qui n’étaient pas fiables puisque non systématiquement reliés aux champs de forces, pour faire des changements prédictifs dans leurs sorties motrices. Toutefois, tous les sujets de ce groupe ont développé une stratégie ingénieuse leur permettant d’émettre une réponse motrice « par défaut » afin de palper ou de sentir le type de la force qu’ils allaient rencontrer dans le premier essai de chaque bloc, à chaque changement de couleur. En effet, ils utilisaient la rétroaction proprioceptive liée à la nature du champ de force afin de prédire la sortie motrice appropriée pour les essais qui suivent, jusqu’au prochain changement de couleur d’écran qui signifiait la possibilité de changement de force. Cette stratégie était efficace puisque la force demeurait la même dans chaque bloc, pendant lequel la couleur de l’écran restait inchangée. Cette étude a démontré que les sujets du groupe II étaient capables d’utiliser les stimuli de couleur pour extraire des informations implicites et explicites nécessaires à la réalisation des mouvements, et qu’ils pouvaient utiliser ces informations pour diminuer l’interférence lors de l’adaptation aux forces anti-corrélées. Les résultats de cette première étude nous ont encouragés à étudier les mécanismes permettant aux sujets de se rappeler d’habiletés motrices multiples jumelées à des stimuli contextuels de couleur. Dans le cadre de notre deuxième étude, nos expériences ont été effectuées au niveau neuronal chez le singe. Notre but était alors d’élucider à quel point les neurones du cortex moteur primaire (M1) peuvent contribuer à la compensation d’un large éventail de différentes forces externes durant un mouvement de flexion/extension du coude. Par cette étude, nous avons testé l’hypothèse liée au modèle MOSAIC, selon laquelle il existe plusieurs modules contrôleurs dans le cervelet qui peuvent prédire chaque contexte et produire un signal de sortie motrice approprié pour un nombre restreint de conditions. Selon ce modèle, les neurones de M1 recevraient des entrées de la part de plusieurs contrôleurs cérébelleux spécialisés et montreraient ensuite une modulation appropriée de la réponse pour une large variété de conditions. Nous avons entraîné deux singes à adapter leurs mouvements de flexion/extension du coude dans le cadre de 5 champs de force différents : un champ nul ne présentant aucune perturbation, deux forces visqueuses anti-corrélées (assistante et résistante) qui dépendaient de la vitesse du mouvement et qui ressemblaient à celles utilisées dans notre étude psychophysique chez l’homme, une force élastique résistante qui dépendait de la position de l’articulation du coude et, finalement, un champ viscoélastique comportant une sommation linéaire de la force élastique et de la force visqueuse. Chaque champ de force était couplé à une couleur d’écran de l’ordinateur, donc nous avions un total de 5 couleurs différentes associées chacune à un champ de force (relation fixe). Les singes étaient bien adaptés aux 5 conditions de champs de forces et utilisaient les stimuli contextuels de couleur pour se rappeler de la sortie motrice appropriée au contexte de forces associé à chaque couleur, prédisant ainsi leur sortie motrice avant de sentir les effets du champ de force. Les enregistrements d’EMG ont permis d’éliminer la possibilité de co-contractions sous-tendant ces adaptations, étant donné que le patron des EMG était approprié pour compenser chaque condition de champ de force. En parallèle, les neurones de M1 ont montré des changements systématiques dans leurs activités, sur le plan unitaire et populationnel, dans chaque condition de champ de force, signalant les changements requis dans la direction, l’amplitude et le décours temporel de la sortie de force musculaire nécessaire pour compenser les 5 conditions de champs de force. Les changements dans le patron de réponse pour chaque champ de force étaient assez cohérents entre les divers neurones de M1, ce qui suggère que la plupart des neurones de M1 contribuent à la compensation de toutes les conditions de champs de force, conformément aux prédictions du modèle MOSAIC. Aussi, cette modulation de l’activité neuronale ne supporte pas l’hypothèse d’une organisation fortement modulaire de M1.

O marketing e a atuação social das empresas: uma relação possível?

The present work is about a study of multiple cases with exploratory and descriptiveperspective and qualitative emphasis. Its field of study is constituted by three local companieswith description of social performance, with emphasis in the personal interview with thecontrollers. Its main objective consists of understanding as it has occurred the marketingrelation with the enterprise social performance in the context of these companies located inthe State of the Rio Grande do Norte who carry out social investments. For this, it hassearched to analyze the types and characteristics of the developed social actions, to evaluatethe motivations and objectives of the accomplishment of social actions, to verify theimportance and influence of the social performance in the dynamics of the companies, toverify the level of specific knowledge and information in the areas of marketing and socialperformance in the companies and to evaluate the process of communication (promotion andspreading) of the social performance carried out by the companies. It has been verified thatthe company A directly associates it its social and ambient activities with differentiationbenefits, competitiveness, creation of value, loyalty, relationships, image, prestige,positioning of the company, sale and financial return, beyond benefits in the internal level asbigger motivation of its employees and retention of talents, not existing rejection to theinterlacement of the concepts related to the marketing and the social one. Already in companyB rejection in relating its practical social to the marketing, being observed after posteriorquestionings, that the relation of direct and indirect form exists and those divulgations of theseactions are carried out, contradicting the arguments of the controllers of that the actions wouldnot be carried out to generate media. In company C, it been verified rejection andcontradiction with relation to the concepts related to the marketing, alleging itself that theimage of the harnessed company to its social performance is not used in proper benefit,evidencing itself that this company divulges its action and is marketable benefited, even so isnot this the main objective of its social programs. It has concluded that the association ofthese two concepts is positive and favorable to the development of the businesses and thesocial actions of the companies, legitimizing them and benefiting the involved company,groups in the actions and the society that profits socially from the private social involvement in the social matters

Vazão em soleiras controladas ou não por comportas

Os controladores de caudal, normalmente implementados em sistemas Supervisory control and data acquisition (SCADA), apresentam uma grande relevância no controlo automático de canais de adução. Para garantir que os controladores de caudal sejam fiáveis em todo o seu domínio de funcionamento (em situações de escoamento com ressalto livre ou submerso e de transição entre escoamentos com ressalto livre e ressalto submerso) foram comparados os resultados dos ensaios experimentais com diferentes métodos de cálculo da vazão em comportas e/ou sobre soleiras. O programa de ensaios foi realizado nos canais laboratorial e experimental da Universidade de Évora. Foram realizados ensaios em comportas planas verticais e em soleiras do tipo Waterways Experiment Station (WES) controladas ou não por comportas planas verticais. Em ambos os casos, foram contempladas as situações de escoamento com ressalto livre e submerso. Os resultados obtidos mostram que: a) para as comportas, o método Rajaratnam e Subramanya (1967a) conduz a bons resultados com um erro percentual médio absoluto MAPE < 1% para o escoamento com ressalto livre e MAPE < 4% para o submerso; a transição entre escoamentos foi identificada corretamente por este método; b) para as soleiras, obtiveram-se bons resultados para o escoamento com ressalto livre para o método USACE (1987), com MAPE < 2%, e para o submerso através do método Alves e Martins (2011), com MAPE < 5%; a transição entre escoamentos pode ser considerada adequada de acordo com a curva experimental de Grace (1963); c) para soleiras controladas por comporta, conseguiram-se bons resultados para o escoamento com ressalto livre recorrendo à equação dos orifícios de pequenas dimensões, com MAPE < 1, 5%, e para o submerso com a equação dos orifícios totalmente submersos com MAPE < 1, 6%; em ambos os casos foi necessária calibração do coeficiente de vazão; a transição entre escoamentos foi adequada pelo método de Grace (1963). Com base nos resultados obtidos, foi possível definir um algoritmo de vazão generalizado para comportas e/ou soleiras que permite a determinação da vazão para as situações de escoamento com ressalto livre e submerso incluindo a transição entre escoamentos; ABSTRACT: Flow controllers, usually implemented in Supervisory Control and Data Acquisition (SCADA) systems, are very important in the automatic control of irrigation canal systems. To ensure that flow controllers are reliable for the entire operating range (free or submerged flow and flow transitions) the experimental results were compared with different methods of flow measurement for gates and/or weirs. The test program was conducted in the laboratory flume and in the automatic canal of the University of ´Evora. Tests were carried in sluice gates and in broad-crested weirs controlled or not by sluice gate. In both cases free and submerged flow conditions were analyzed. The results show that: a) for the sluice gates, the method of Rajaratnam e Subramanya (1967a) leads to good results with a mean absolute percentage error (MAPE) < 1% for free flow and MAPE < 4% for submerged flow. The transition between flows is correctly identified by this method; b) for the uncontrolled weir, good results were obtained for free flow with the method USACE (1987) with MAPE < 2%, and for submerged flow by the method Alves e Martins (2011) with MAPE < 5%. The transition between flows can be accurately defined by the experimental curve of Grace (1963); c) for the controlled weir, good results were achieved for the free flow with the small orifice equation with MAPE < 1.5% and for submerged flow with the submerged orifice equation with MAPE < 1.6%; in both cases the calibration of the discharge coefficient is needed. The transition between flows can be accomplished through Grace (1963) method. Based on the obtained results, it was possible to define a generalized flow algorithm for gates and/or weirs that allows flow determination for free and submerged flow conditions including the transition between flows.

Brain emotional learning based control of a SDOF structural system with a MR damper

This paper describes the application of a Brain Emotional Learning (BEL) controller to improve the response of a SDOF structural system under an earthquake excitation using a magnetorheological (MR) damper. The main goal is to study the performance of a BEL based semi-active control system to generate the control signal for a MR damper. The proposed approach consists of a two controllers: a primary controller based on a BEL algorithm that determines the desired damping force from the system response and a secondary controller that modifies the input current to the MR damper to generate a reference damping force. A parametric model of the damper is used to predict the damping force based on the piston motion and also the current input. A Simulink model of the structural system is developed to analyze the effectiveness of the semi-active controller. Finally, the numerical results are presented and discussed.

Autoavaliação institucional na dimensão do SINAES comunicação com a sociedade : estudo de múltiplos casos em instituições de ensino superior do Rio Grande do Norte

This study is about the institutional self-evaluation in Dimension 4, "Communication with Society", from the National System of Higher Education Evaluation SINAES, mandatory for all universities in Brazil. A multiple cases study was conducted with three institutions from Rio Grande do Norte, and the goal was to know how this evaluation is made, describing the concept for the evaluation of communication proposed by them, identifying controllers or emancipator aspects, categorizing methodological procedures and discussing the difficulties reported in the communication evaluation process. Coordinators of the institutions Evaluating Committees were interviewed and data categorized by means of qualitative content analysis. It was noted characteristics of the current controller, emancipator and hybrid designs in the three institutions for evaluation of communication, revealing the lack of a theoretical corpus that transits in accordance with the systemic perspective and epistemology of complexity from SINAES. It was found that the most frequently reported difficulties in the evaluation processes of communication are in the preparation stage, especially in the definition of indicators and tools and awareness work. The weakness in planning makes their own activities in the sector of communication become targets of assessment, forming goals poorly related with broader organizational goals. It was also concluded that the technical evaluation cannot override the issues associated with the broader issue of the complexity surrounding the assessment paradigm proposed by SINAES because contradictions and imperfections are part of the evaluation process and several references are current in the literature to support this view. Finally, it is said that objectives such as transparency and behavioral changes can rely on methodologies and techniques for research on the question of the construction of meaning

Pressure management in water distribution systems: current status, proposals, and future trends

Pressure management (PM) is commonly used in water distribution systems (WDSs). In the last decade, a strategic objective in the field has been the development of new scientific and technical methods for its implementation. However, due to a lack of systematic analysis of the results obtained in practical cases, progress has not always been reflected in practical actions. To address this problem, this paper provides a comprehensive analysis of the most innovative issues related to PM. The methodology proposed is based on a case-study comparison of qualitative concepts that involves published work from 140 sources. The results include a qualitative analysis covering four aspects: (1) the objectives yielded by PM; (2) types of regulation, including advanced control systems through electronic controllers; (3) new methods for designing districts; and (4) development of optimization models associated with PM. The evolution of the aforementioned four aspects is examined and discussed. Conclusions regarding the current status of each factor are drawn and proposals for future research outlined

Sintonia automática de controladores PID: uma abordagem neuro - genética

Dissertação de dout. em Electrónica e Computação, Faculdade de Ciências e Tecnologia, Univ. do Algarve, 2004

Ambiente computacional paradesenvolvimento de aplicações de controladores lógicos programáveis baseado em linguagens SFC e ST

This work proposes an environment for programming programmable logic controllers applied to oil wells with BCP type method of artificially lifting. The environment will have an editor based in the diagram of sequential functions for programming of PLCs. This language was chosen due to the fact of being high-level and accepted by the international standard IEC 61131-3. The use of these control programs in real PLC will be possible with the use of an intermediate level of language based on XML specification PLCopen T6 XML. For the testing and validation of the control programs, an area should be available for viewing variables obtained through communication with a real PLC. Thus, the main contribution of this work is to develop a computational environment that allows: modeling, testing and validating the controls represented in SFC and applied in oil wells with BCP type method of artificially lifting

Detecção de interface em tanques de petróleo usando transmissores de nível e controladores Fuzzy

This work presents a proposal to detect interface in atmospheric oil tanks by installing a differential pressure level transmitter to infer the oil-water interface. The main goal of this project is to maximize the quantity of free water that is delivered to the drainage line by controlling the interface. A Fuzzy Controller has been implemented by using the interface transmitter as the Process Variable. Two ladder routine was generated to perform the control. One routine was developed to calculate the error and error variation. The other was generate to develop the fuzzy controller itself. By using rules, the fuzzy controller uses these variables to set the output. The output is the position variation of the drainage valve. Although the ladder routine was implemented into an Allen Bradley PLC, Control Logix family it can be implemented into any brand of PLCs