Shear stress and sediment transport calculations for sheet flow under waves

A simple method is provided for calculating transport rates of not too fine (d(50) greater than or equal to 0.20 mm) sand under sheet flow conditions. The method consists of a Meyer-Peter-type transport formula operating on a time-varying Shields parameter, which accounts for both acceleration-asymmetry and boundary layer streaming. While velocity moment formulae, e.g.., = Constant x calibrated against U-tube measurements, fail spectacularly under some real waves (Ribberink, J.S., Dohmen-Janssen, C.M., Hanes, D.M., McLean, S.R., Vincent, C., 2000. Near-bed sand transport mechanisms under waves. Proc. 27th Int. Conf. Coastal Engineering, Sydney, ASCE, New York, pp. 3263-3276, Fig. 12), the new method predicts the real wave observations equally well. The reason that the velocity moment formulae fail under these waves is partly the presence of boundary layer streaming and partly the saw-tooth asymmetry, i.e., the front of the waves being steeper than the back. Waves with saw-tooth asymmetry may generate a net landward sediment transport even if = 0, because of the more abrupt acceleration under the steep front. More abrupt accelerations are associated with thinner boundary layers and greater pressure gradients for a given velocity magnitude. The two real wave effects are incorporated in a model of the form Q(s)(t) = Q(s)[theta(t)] rather than Q(S)(t) = Q(S)[u(infinity)(t)], i.e., by expressing the transport rate in terms of an instantaneous Shields parameter rather than in terms of the free stream velocity, and accounting for both streaming and accelerations in the 0(t) calculations. The instantaneous friction velocities u(*)(t) and subsequently theta(t) are calculated as follows. Firstly, a linear filter incorporating the grain roughness friction factor f(2.5) and a phase angle phi(tau) is applied to u(infinity)(t). This delivers u(*)(t) which is used to calculate an instantaneous grain roughness Shields parameter theta(2.5)(t). Secondly, a constant bed shear stress is added which corresponds to the streaming related bed shear stress -rho ($) over bar((u) over tilde(w) over tilde)(infinity) . The method can be applied to any u(infinity)(t) time series, but further experimental validation is recommended before application to conditions that differ strongly from the ones considered below. The method is not recommended for rippled beds or for sheet flow with typical prototype wave periods and d(50) < 0.20 turn. In such scenarios, time lags related to vertical sediment movement become important, and these are not considered by the present model. (C) 2002 Elsevier Science B.V. All rights reserved.

Quantification and stability of everolimus (SDZ RAD) in human blood by high-performance liquid chromatography-electrospray tandem mass spectrometry

We report here a validated method for the quantification of a new immunosuppressant drug, everolimus (SDZ RAD), using HPLC-tandem mass spectrometry. Whole blood samples (500 mul) were prepared by protein precipitation, followed by C-18 solid-phase extraction. Mass spectrometric detection was by selected reaction monitoring with an electrospray interface operating in positive ionization mode. The assay was linear from 0.5 to 100 mug/l (r(2) > 0.996, n = 9). The analytical recovery and inter-day imprecision, determined using whole blood quality control samples (n = 5) at 0.5, 1.2, 20.0, and 75.0 mug/l, was 100.3-105.4% and less than or equal to7.6%, respectively. The assay had a mean relative recovery of 94.8 +/- 3.8%. Extracted samples were stable for up to 24 h. Fortified everolimus blood samples were stable at -80 degreesC for at least 8 months and everolimus was found to be stable in blood when taken through at least three freeze-thaw cycles. The reported method provides accurate, precise and specific measurement of everolimus in blood over a wide analytical range and is currently supporting phase 11 and III clinical trials. (C) 2002 Elsevier Science B.V. All rights reserved.

Co-crystallization of sucrose at high concentration in the presence of glucose and fructose

Co-crystallization of sucrose from a highly concentrated sucrose syrup (less than or equal to 7% moisture, w/w) at 131 degreesC with 0, 5, 10, 15, and 20% of fructose, glucose, or a mixture of fructose and glucose was investigated. The crystallization of sucrose was delayed in presence of these lower molecular weight sugars. The DSC melting endotherm of cocrystallized samples exhibited a decrease in crystalline sucrose in the sample as a function of increased level of glucose and fructose. The mechanical strength of co-crystallized granules was found to be related to the moisture content and the amount of glucose or fructose content in the sample. The samples containing 10, 15, and 20% glucose in co-crystallized product demonstrated crystallization of glucose in its monohydrate form during 1 mo of storage.

High dependency units: Issues to consider in their planning

This review discusses the issues to be considered in establishing new or extending existing high dependency unit (HDU) services. A defined high dependency service becomes cost-effective when patient care requires more than one nurse for three patients. Professional guidelines for HDUs vary and there are no national accreditation criteria. Casemix and service delivery specifications for the HDU need to be defined and agreed upon within the institution. Establishing a new HDU service requires changes to care delivery. Many potential HDU patients are currently managed in general wards or in the intensive care unit. The service should be discussed widely and marketed within the institution, and the development of defined working relationships with the ICU and primary care teams oil the wards is mandatory.

High prevalence, persistent hazardous drinking among new zealand tertiary students

Aims: To determine the prevalence of hazardous drinking and alcohol-related negative consequences in New Zealand tertiary students, and to identify predictors of hazardous drinking across a 6-month period. Methods: A total of 1480 tertiary students living in halls of residence was surveyed at the start of the academic year, and a subsample of 967 students was followed up 6 months later. Questionnaire items included quantity and frequency of drinking, alcohol-related problems, use of other substances, and the Alcohol Use Disorders Identification Test (AUDIT). Drinking at follow-up was modelled using demographic characteristics, mental well-being, other substance use, alcohol-related problems, and hall drinking norms, measured at baseline. Results: Among drinkers, mean (+/- SD) weekly consumption was 243 +/- 241 and 135 +/- 157 g of ethanol for males and females respectively. The majority of male (60.0%) and female (58.2%) drinkers typically consumed more than national safe drinking guidelines. Mean (+/- SD) AUDIT scores were 10.9 +/- 7.6 for males and 7.6 +/- 5.9 for females. After controlling for AUDIT scores at baseline, increased AUDIT scores at follow-up were higher with lower age, Maori ethnicity, smoking, cannabis use, high levels of alcohol-related negative consequences, and higher levels of drinking in the student's hall of residence. Conclusions: Hazardous drinking is widespread and persistent among students living in the halls of residence. There is a need for university alcohol policies and intervention approaches among New Zealand tertiary students.

Scale-up of mixer granulators for effective liquid distribution

There is considerable anecdotal evidence from industry that poor wetting and liquid distribution can lead to broad granule size distributions in mixer granulators. Current scale-up scenarios lead to poor liquid distribution and a wider product size distribution. There are two issues to consider when scaling up: the size and nature of the spray zone and the powder flow patterns as a function of granulator scale. Short, nucleation-only experiments in a 25L PMA Fielder mixer using lactose powder with water and HPC solutions demonstrated the existence of different nucleation regimes depending on the spray flux Psi(a)-from drop-controlled nucleation to caking. In the drop-controlled regime at low Psi(a) values. each drop forms a single nucleus and the nuclei distribution is controlled by the spray droplet size distribution. As Psi(a) increases, the distribution broadens rapidly as the droplets overlap and coalesce in the spray zone. The results are in excellent agreement with previous experiments and confirm that for drop-controlled nucleation. Psi(a) should be less than 0.1. Granulator flow studies showed that there are two powder flow regimes-bumping and roping. The powder flow goes through a transition from bumping to roping as impeller speed is increased. The roping regime gives good bed turn over and stable flow patterns. This regime is recommended for good liquid distribution and nucleation. Powder surface velocities as a function of impeller speed were measured using high-speed video equipment and MetaMorph image analysis software, Powder surface velocities were 0.2 to 1 ms(-1)-an order of magnitude lower than the impeller tip speed. Assuming geometrically similar granulators, impeller speed should be set to maintain constant Froude number during scale-up rather than constant tip speed to ensure operation in the roping regime. (C) 2002 Published by Elsevier Science B.V.

Population balance modelling of granulation with a physically based coalescence kernel

It was previously published by the authors that granules can either coalesce through Type I (when granules coalesce by viscous dissipation in the surface liquid layer before their surfaces touch) or Type II (when granules are slowed to a halt during rebound, after their surfaces have made contact) (AIChE J. 46 (3) (2000) 529). Based on this coalescence mechanism, a new coalescence kernel for population balance modelling of granule growth is presented. The kernel is constant such that only collisions satisfying the conditions for one of the two coalescence types are successful. One constant rate is assigned to each type of coalescence and zero is for the case of rebound. As the conditions for Types I and II coalescence are dependent on granule and binder properties, the coalescence kernel is thus physically based. Simulation results of a variety of binder and granule materials show good agreement with experimental data. (C) 2002 Elsevier Science Ltd. All rights reserved.

Crystallization of PNMT, the adrenaline-synthesizing enzyme, is critically dependent on a high protein concentration

Phenylethanolamine N-methyltransferase, PNMT, utilizes the methylating cofactor S-adenosyl-L-methionine to catalyse the synthesis of adrenaline. Human PNMT has been crystallized in complex with an inhibitor and the cofactor product S-adenosyl-L-homocysteine using the hanging-drop technique with PEG 6000 and lithium chloride as precipitant. A critical requirement for crystallization was a high enzyme concentration (>90 mg ml(-1)) and cryocrystallography was used for high-quality data measurement. Diffraction data measured from a cryocooled crystal extend to a resolution of 2.3 Angstrom. Cryocooled crystals belong to space group P4(3)2(1)2 and have unit-cell parameters a = b = 94.3, c = 187.7 Angstrom.

Structure of CcmG/DsbE at 1.14 angstrom resolution: High-fidelity reducing activity in an indiscriminately oxidizing environment

CcmG is unlike other periplasmic thioredoxin (TRX)like proteins in that it has a specific reducing activity in an oxidizing environment and a high fidelity of interaction. These two unusual properties are required for its role in c-type cytochrome maturation. The crystal structure of CcmG reveals a modified TRX fold with an unusually acidic active site and a groove formed from two inserts in the fold. Deletion of one of the groove-forming inserts disrupts c-type cytochrome formation. Two unique structural features of CcmG-an acidic active site and an adjacent groove-appear to be necessary to convert an indiscriminately binding scaffold, the TRX fold, into a highly specific redox protein.

Applications of accurate, high-precision Pb isotope ratio measurement by multi-collector ICP-MS

The isotope composition of Ph is difficult to determine accurately due to the lack of a stable normalisation ratio. Double and triple-spike addition techniques provide one solution and presently yield the most accurate measurements. A number of recent studies have claimed that improved accuracy and precision could also be achieved by multi-collector ICP-MS (MC-ICP-MS) Pb-isotope analysis using the addition of Tl of known isotope composition to Pb samples. In this paper, we verify whether the known isotope composition of Tl can be used for correction of mass discrimination of Pb with an extensive dataset for the NIST standard SRM 981, comparison of MC-ICP-MS with TIMS data, and comparison with three isochrons from different geological environments. When all our NIST SRM 981 data are normalised with one constant Tl-205/Tl-203 of 2.38869, the following averages and reproducibilities were obtained: Pb-207/Pb-206=0.91461+/-18; Pb-208/Ph-206 = 2.1674+/-7; and (PbPh)-Pb-206-Ph-204 = 16.941+/-6. These two sigma standard deviations of the mean correspond to 149, 330, and 374 ppm, respectively. Accuracies relative to triple-spike values are 149, 157, and 52 ppm, respectively, and thus well within uncertainties. The largest component of the uncertainties stems from the Ph data alone and is not caused by differential mass discrimination behaviour of Ph and Tl. In routine operation, variation of sample introduction memory and production of isobaric molecular interferences in the spectrometer's collision cell currently appear to be the ultimate limitation to better reproducibility. Comparative study of five different datasets from actual samples (bullets, international rock standards, carbonates, metamorphic minerals, and sulphide minerals) demonstrates that in most cases geological scatter of the sample exceeds the achieved analytical reproducibility. We observe good agreement between TIMS and MC-ICP-MS data for international rock standards but find that such comparison does not constitute the ultimate. test for the validity of the MC-ICP-MS technique. Two attempted isochrons resulted in geological scatter (in one case small) in excess of analytical reproducibility. However, in one case (leached Great Dyke sulphides) we obtained a true isochron (MSWD = 0.63) age of 2578.3 +/- 0.9 Ma, which is identical to and more precise than a recently published U-Pb zircon age (2579 3 Ma) for a Great Dyke websterite [Earth Planet. Sci. Lett. 180 (2000) 1-12]. Reproducibility of this age by means of an isochron we regard as a robust test of accuracy over a wide dynamic range. We show that reliable and accurate Pb-isotope data can be obtained by careful operation of second-generation MC-ICP magnetic sector mass spectrometers. (C) 2002 Elsevier Science B.V. All rights reserved.

High-frequency climatic oscillations recorded in a Holocene coral reef at Leizhou Peninsula, South China sea

A detailed study of the Goniopora reef profile at Dengloujiao, Xuwen County, Leizhou Peninsula, the northern coast of the South China Sea suggests that a series of high-frequency, large-amplitude and abrupt cold events occurred during the Holocene Hypsithermal, an unusual phenomenon termed Leizhou Events in this paper. This period (corresponding to C-14 age of 6.2 -6.7 kaBP or calendar age of 6.7-7.2 kaBP), when the climatic conditions were ideal for coral. reefs to develop, can be divided into at least nine stages. Each stage (or called a climate optimum), lasting about 20 to 50 a, was terminated by an abrupt cold nap and (or) a sea-level lowering event in winter, leading to widespread emergence and death of the Goniopora corals, and growth discontinuities on the coral surface. Such a cyclic process resulted in the creation of a > 4m thick Goniopora reef flat. During this period, the crust subsided periodically but the sea level was rising. The reef profile provides valuable archives for the study of decadal-scale mid-Holocene climatic oscillations in the tropical area of South China. Our results provide new evidence for high-frequency climate instability in the Holocene Hypsithermal, and challenge the traditional understanding of Holocene climate.

Myocardial infarction and type II diabetes - preferential treatment for high risk patients?

Objectives: To compare variability of blood glucose concentration in patients with type II diabetes with (cases) and without (controls) myocardial infarction. A secondary objective was identification of predictive factors for higher blood glucose on discharge from hospital. Design: A retrospective matched case-control study. Participants: Medical notes of 101 type II diabetic patients admitted with a myocardial infarction (MI) and 101 type II diabetic patients (controls) matched on gender and age with no MI were reviewed. Blood glucose concentrations over two consecutive 48-h periods were collected. Demographic data and therapy on admission/discharge were also collected. Results: Patient characteristics were comparable on recruitment excluding family history of cardiovascular disease (P =0.003), dyslipidaemia (P =0.004) and previous history of MI (P =0.007). Variability of blood glucose in cases was greater over the first 48 h compared with the second 48 h (P =0.03), and greater when compared with controls over the first 48 h (P =0.01). Cases with blood glucose on discharge >8.2 mmol / L (n =45) were less likely to have a history of previous MI (P =0.04), ischaemic heart disease (P =0.03) or hypertension (P =0.02). Conclusions: Type II diabetics with an MI have higher and more variable blood glucose concentrations during the first 48 h of admission. Only cardiovascular 'high risk' patients had target blood glucose set on discharge. The desirability of all MI patients with diabetes, having standardized-glucose infusions to reduce variability of blood glucose, should be evaluated in a randomized controlled trial.