Living cationic polymerization of isobutene

The polymerization of isobutene initiated by 1-chloro-1-phenylethane has been investigated, and molecular weight studies conducted using size exclusion chromatography. Polymerizations carried out in a 40/60 (v/v) mixture of dichloromethaneIcyclohexane, using titanium (IV) chloride as a catalyst in the presence of pyridine at -30 °C were found to be controlled and living. The number average molecular weights of the polymers increased linearly with monomer conversion, and the molecular weight distributions were between 1.15 and 1.20. Efficiencies of initiation were between 80 and 100%, and evidence was found to suggest that backbiting to the initiator had occurred, resulting in the formation of cyclic oligomers during the early stages of polymerization. The kinetics of polymerization can be explained in terms of active species in. equilibrium with dormant species. The effects of temperature. and dielectric constant on this equilibrium were studied and a model based upon the Fuoss equation was developed. Pyridine was found to behave as proton trap in the system, and when it was used in excess the rate of polymerization was retarded. By assuming that the catalyst and pyridine formed a one to one complex, it was possible to show that the reaction was second order with respect to the catalyst. The synthesis of low molecular weight polyisobutenes was studied. When the concentration of initiator was increased relative to that of the isobutene, such that the theoretical degree of polymerization was 20 or less, the rate of initiation was slow compared to propagation. The efficiency of initiation in these polymerizations was typically between 30 and 40 %. Optimal conditions of temperature. and.catalyst concentration were established, leading to a 60 % efficiency of initiation. A one-pot synthesis of phenol end-capped polyisobutene was attempted by adding phenol at the end of a living polymerization. Evidence to substantiate the existence of capped polymer chains in the resultant product was inconclusive. Block copolymerizations of oxetane and isobutene were conducted using 1-chloro-1phenylethane/TiCl4, but no copolymer or oxetane homopolymer could be isolated.

Living cationic polymerization of styrene monomers

This thesis describes an experimental investigation of synthesis of polystyrene under various polymerization conditions such as solvent polarity, temperature, initial concentrations of initiator, catalyst, monomer and added salts or co-catalyst, which was achieved using the living cationic polymerization technology in conjunction with gel permeation chromatography (GPC) and NMR spectroscopy. Polymerizations of styrene were conducted using 1-phenyl ethylchloride (1-PEC) as an initiator and tin tetrachloride (SnCI4) as a catalyst in the presence of tetra-n-Butylammonium chloride (nBu4NCI). Effects of solvent polarity varied by mixing dichloromethane (DCM) and less polar cyclohexane (C.hex), temperature, initial concentrations of SnC14, 1-PEC and nBu4NCI on the polymerizations were examined, and the conditions under which a living polymerization can be obtained were optimised as: [styrene]o ~ 0.75 - 2 M; [1-PEC]o ~ 0.005 - 0.05 M; [SnCI4Jo ~ 0.05 - 0.4 M; [nBu4NCIJo ~ 0.001 - 0.1 M; DCM/C.hex ~ 50/0 - 20/30 v/v; T ~ 0 to -45°C. Kinetic studies of styrene polymerization using the Omnifit sampling method showed that the number average molecular weight (Mn) of the polymers obtained increased in direct proportion to monomer conversion and agreed well with the theoretical Mn expected from the concentration ratios of monomer to initiator. The linearities of both the 1n([MJoI[M]) vs. time plot and the Mn vs. monomer conversion plot, and the narrow molecular weight distribution (MWD) measured using GPC demonstrated the livingness of the polymerizations, indicating the absence of irreversible termination and transfer within the lifetimes of the polymerizations. The proposed 'two species' propagation mechanism was found to apply for the styrene polymerization with 1-PEC/SnCI4 in the presence of nBu4NCl. The further kinetic experiments showed that living styrene polymerizations were achieved using the 1-PEC/SnCI4 initiating system in mixtures of DCM/C.hex 30/20 v/v at -15°C in the presence of various bromide salts, tetra-n-butylammonium bromide, tetra-n-pentylammonium bromide, tetra-n-heptylammonium bromide, and tetra-n-octylammonium bromide, respectively. The types of the bromide salts were found to have no significant effect on monomer conversion, Mn, polydispersity and initiation efficiency. Living polymerizations of styrene were also achieved using titanium tetrachloride (TiCI4) as a catalyst and 1-PEC as an initiator in the presence of a small amount of 2,6-di-tert-butylpyridine or pyridine instead of nBu4NCl. GPC analysis showed that the polymers obtained had narrow polydispersities (P.D. < 1.3), and the linearities of both the In([MJo/[MJ) vs. time plot and the Mn vs. monomer conversion plot demonstrated that the polymerizations are living, when the ratio of DCM and C.hex was less than 40 : 10 and the reaction temperature was not lower than -15°C. The reaction orders relative to TiCl4 and 1-PEC were estimated from the investigations into the rate of polymerization to be 2.56 and 1.0 respectively. lH and 13C NMR analysis of the resultant polystyrene would suggest the end-functionality of the product polymers is chlorine for all living polymerizations.

The cationic ring-opening polymerization of cyclic ethers

The kinetics and mechanisms of ring opening polymerization and copolymerizntion of different cyclic ethers were studied using mainly a cationic system of iinitiation. BF30Et2/ethanediol. The cyclic ethers reacted differently showing that ring strain and basicity are the main driving forces in cationic ring opening polymerizaion. In most cases it was found that the degree of polymerization is controlled kinetically via terminations with the counterion and the monomers, and that the contribution of each type of reaction to the overall termination differs markedly. The Gel permeation chromatography studies showed that the molecular weight distribution of the samples of polyoxetanes were bimodal. This was in accordance with previous work establishing that the cyclic tetramer is found in much higher proportions than any of the other cyclic oligomers. However the molecular weight distribution of the copolymers made from oxetane and THF or from oxetane and oxepane were shown to be unimodal. These observations could be explained by a change in the structure of the growing end involved in the cationic polymerization. In addition crown ethers like dibenzo-crown-6 and compounds such as veratrole are believed to stabilise the propagating end and promote the formation of living polymers from oxetane.

The polymerization of lactic acid anhydrosulphite by anionic initiators

This thesis is primarily concerned with the synthesis and polymerization of 5-methyl-1;3, 2-dioxathiolan-4-one-2-oxide (lactic acid anhydrosulphite (LAAS)) using anionic initiators under various conditions. Poly(lactic acid) is a biodegradable polymer which finds many uses in biomedical applications such as drug-delivery and wound-support systems. For such applications it is desirable to produce polymers having predictable molecular weight distributions and crystallinity, The use of anionic initiators offers a potential route to the creation of living polymers. The synthesis of LAAS was achieved by means of an established route though the procedure was modified to some extent and a new method of purification of the monomer using copper oxides was introduced, Chromatographic purification methods were also examined but found to be ineffective. An unusual impurity was discovered in some syntheses and this was identified by means of 1H and 13C NMR, elemental analysis and GC-MS. Since poly-α-esters having hydroxyl-bearing substituents might be expected to have high equilibrium water contents and hence low surface tension characteristics which might aid bio-compatibility, synthesis of gluconic acid anhydrosulphite was also attempted and the product characterised by 1H and 13C NMR. The kinetics of the decomposition of lactic acid anhydrosulphite by lithium tert-butoxide in nitrobenzene has been examined by means of gas evolution measurements. The kinetics of the reaction with potassium tert-butoxide (and also sec-butyl lithium) in tetrahydrofuran has been studied using calorimetric techniques. LAAS was block co-polymerized with styrene and also with 1,3-butadiene in tetrahydrofuran (in the latter case a statistical co-polymer was also produced).

The ring opening polymerization of ring strained cyclic ethers

The kinetics and mechanisms of the ring-opening polymerization of oxetane were studied using cationic and coordinated anionic catalysts. The cationic initiators used were BF30Et2!/ethanol, BF30Et2!/ethanediol and BF30Et2/propantriol. Kinetic determinations with the BF30Et2/diol system indicated that a 1: 1 BF3:0H ratio gave the maximum rate of polymerization and this ratio was employed to detenmne the overall rates of polymerization. An overall second-order dependence was obtained when the system involved ethanediol or propantriol as co-catalyst and a 3/2-order dependence with ethanol, in each case the monomer gave a first-order relationship. This suggested that two mechanisms accounted for the cationic polymerization. These mechanisms were investigated and further evidence for these was obtained from the study of the complex formation of BF30Et2 and the co-catalysts by 1H NMR. Molecular weight studies (using size-exclusion chromatography) indicated that the hydroxyl ion acted as a chain transfer reagent when the [OH] > [BF3]. A linear relationship was observed when the number average molecular weight was plotted against [oxetane] at constant [BF3:0H], and similarly a linear dependency was observed on the BF3:0H 1:1 adduct at constant oxetane concentration. Copolymerization of oxetane and THF was carried out using BF30Et2/ethanol system. The reactivity ratios were calculated as rOXT = 1.2 ± 0.30 and rTHF = 0.14 ± 0.03. These copolymers were random copolymers with no evidence of oligomer formation. The coordinated anionic catalyst, porphinato-aluminium chloride [(TPP)AICl], was used to produce a living polymerization of oxetane. An overall third-order kinetics was obtained, with a second-order with respect to the [(TPP)AICl] and a first-order with respect to the [oxetane] and a mechanism was postulated using these results. The stereochemistry of [(TPP)AlCl] catalyst was investigated using cyclohexene and cyclopentene oxide monomers, using extensive 1H NMR, 2-D COSY and decoupling NMR techniques it was concluded that [(TPP)AlCl] gave rise to stereoregular polymers.

Reversible addition–fragmentation chain transfer polymerization of 2-chloro-1,3-butadiene

Controlled polymerization of 2-chloro-1,3-butadiene using reversible addition–fragmentation chain transfer (RAFT) polymerization has been demonstrated for the first time. 2-Chloro-1,3-butadiene, more commonly known as chloroprene, has significant industrial relevance as a crosslinked rubber, with uses ranging from adhesives to integral automotive components. However, problems surrounding the inherent toxicity of the lifecycle of the thiourea-vulcanized rubber have led to the need for control over the synthesis of poly(2-chloro-1,3-butadiene). To this end, four chain transfer agents in two different solvents have been trialed and the kinetics are discussed. 2-Cyano-2-propylbenzodithioate (CPD) is shown to polymerize 2-chloro-1,3-butadiene in THF, using AIBN as an initiator, with complete control over the target molecular weight, producing polymers with low polydispersities (Mw/Mn < 1.25 in all cases).

The pH-induced swelling and collapse of a polybase brush synthesized by atom transfer radical polymerization

We have used neutron reflectometry to characterize the swelling behaviour of brushes of poly[2-(diethyl amino)ethyl methacrylate], a polybase, as a function of pH. The brushes, synthesized by the "grafting from" method of atom transfer radical polymerization, were observed to approximately double their thickness in low pH solutions, although the pK is shifted to a lower pH than in dilute solution. The composition-depth profile obtained from the reflectometry experiments for the swollen brushes reveals a region depleted in polymer between the substrate and the extended part of the brush.

Controlled RAFT polymerization and zinc binding performance of catechol-inspired homopolymers

Incorporation of catechols into polymers has long been of interest due to their ability to chelate heavy metals and their use in the design of adhesives, metal-polymer nanocomposites, antifouling coatings, and so on. This paper reports, for the first time, the reversible addition-fragmentation chain transfer (RAFT) polymerization of a protected catechol-inspired monomer, 3,4-dimethoxystyrene (DMS), using commercially available trithiocarbonate, 2-(dodecylthiocarbonothioylthio)-2-methylpropionic acid (DDMAT), as a chain transfer agent. Our identified RAFT system produces well-defined polymers across a range of molecular weights (5-50 kg/mol) with low molar mass dispersities (Mw/Mn < 1.3). Subsequent facile demethylation of poly(3,4-dimethoxystyrene) (PDMS) yields poly(3,4-dihydroxystyrene) (PDHS), a catechol-bearing polymer, in quantitative yields. Semiquantitative zinc binding capacity analysis of both polymers using SEM/EDXA has demonstrated that both PDMS and PDHS have considerable surface binding (65% and 87%, respectively), although the films deposited from PDMS are of a better quality and processability due to solubility and lower processing temperatures. © 2014 American Chemical Society.

Competitive processes in controlled cationic ring-opening polymerization of oxetane:a Lotka-Volterra predator-prey model of two growing species competing for the same resources

The activation-deactivation pseudo-equilibrium coefficient Qt and constant K0 (=Qt x PaT1,t = ([A1]x[Ox])/([T1]x[T])) as well as the factor of activation (PaT1,t) and rate constants of elementary steps reactions that govern the increase of Mn with conversion in controlled cationic ring-opening polymerization of oxetane (Ox) in 1,4-dioxane (1,4-D) and in tetrahydropyran (THP) (i.e. cyclic ethers which have no homopolymerizability (T)) were determined using terminal-model kinetics. We show analytically that the dynamic behavior of the two growing species (A1 and T1) competing for the same resources (Ox and T) follows a Lotka-Volterra model of predator-prey interactions. © 2011 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

The European Patterns of "Homo Academicus“ and The Chances of Its Evolution In Current Hungarian Higher Education

In the recent four or five years, there have been abrupt and radical changes in the governance of Hungarian higher education. It can then be interesting to assess the state of “homo academicus“ as it looks currently in Hungary. The notion of “homo academicus“ is obvious: it concerns participants in the system of a country’s higher education. The paper as follows still comes back to the definition of “homo academicus“ by referring first to it as occupation, or rather as a profession that can be interpreted in terms of sociology. Secondly, some historic patterns can also be mobilised, based on the assumption that university is a very European institutions that is even rooted in the tradition of the Middle Ages. The elbow-room of seeking for identity and the role to be filled by academics are limited by the effective system of the governance of higher education. It is a key to the chances of academics of meeting the historically corroborated professional standards that they exercise academic freedom. As it cannot be done individually, but in cooperation (through a collegial system), academic freedom is always combined with collective action. The field where this freedom can be exercised can be specified through university autonomy, the lack of which makes a serious barrier to the full development of a character of “homo academicus“. This is now the case in Hungary, the paper suggests. The paper seeks to gain deeper understanding of the character of academics, their vocation and professional roles, and the governance of higher education, serving as the environment for academic activity, by creating a conceptual framework. The paper is established on the results of sociological research and the experience of legal management, although it remains to be of theoretical nature. It criticises the current Hungarian situation of the governance of higher education, arguing for the reconstruction of university autonomy and financial stability. It also emphasises the importance of predictable regulations.

The evolutionary relationships and age of Homo naledi : an assessment using dated Bayesian phylogenetic methods

Acknowledgements We wish to express our gratitude to the National Geographic Society and the National Research Foundation of South Africa for funding the discovery, recovery, and analysis of the H. naledi material. The study reported here was also made possible by grants from the Social Sciences and Humanities Research Council of Canada, the Canada Foundation for Innovation, the British Columbia Knowledge Development Fund, the Canada Research Chairs Program, Simon Fraser University, the DST/NRF Centre of Excellence in Palaeosciences (COE-Pal), as well as by a Discovery Grant from the Natural Sciences and Engineering Research Council of Canada, a Young Scientist Development Grant from the Paleontological Scientific Trust (PAST), a Baldwin Fellowship from the L.S.B. Leakey Foundation, and a Seed Grant and a Cornerstone Faculty Fellowship from the Texas A&M University College of Liberal Arts. We would like to thank the South African Heritage Resource Agency for the permits necessary to work on the Rising Star site; the Jacobs family for granting access; Wilma Lawrence, Bonita De Klerk, Merrill Van der Walt, and Justin Mukanku for their assistance during all phases of the project; Lucas Delezene for valuable discussion on the dental characters of H. naledi. We would also like to thank Peter Schmid for the preparation of the Dinaledi fossil material; Yoel Rak for explaining in detail some of the characters used in previous studies; William Kimbel for drawing our attention to the possibility that there might be a problem with Dembo et al.’s (2015) codes for the two characters related to the articular eminence; Will Stein for helpful discussion about the Bayesian analyses; Mike Lee for his comments on this manuscript; John Hawks for his support in organizing the Rising Star workshop; and the associate editor and three anonymous reviewers for their valuable comments. We are grateful to S. Potze and the Ditsong Museum, B. Billings and the School of Anatomical Sciences at the University of the Witwatersrand, and B. Zipfel and the Evolutionary Studies Institute at the University of the Witwatersrand for providing access to the specimens in their care; the University of the Witwatersrand, the Evolutionary Studies Institute, and the South African National Centre of Excellence in PalaeoSciences for hosting a number of the authors while studying the material; and the Western Canada Research Grid for providing access to the high-performance computing facilities for the Bayesian analyses. Last but definitely not least, we thank the head of the Rising Star project, Lee Berger, for his leadership and support, and for encouraging us to pursue the study reported here.

Preparation of Polymer Nanoparticles by Ring Opening Metathesis Polymerization in Aqueous Dispersed Systems with Water-Soluble Ruthenium-based Catalyst

Ring opening metathesis polymerization (ROMP) is a variant of olefin metathesis used to polymerize strained cyclic olefins. Ruthenium-based Grubbs’ catalysts are widely used in ROMP to produce industrially important products. While highly efficient in organic solvents such as dichloromethane and toluene, these hydrophobic catalysts are not typically applied in aqueous systems. With the advancements in emulsion and miniemulsion polymerization, it is promising to conduct ROMP in an aqueous dispersed phase to generate well-defined latex nanoparticles while improving heat transfer and reducing the use of volatile organic solvents (VOCs). Herein I report the efforts made using a PEGylated ruthenium alkylidene as the catalyst to initiate ROMP in an oil-in-water miniemulsion. 1H NMR revealed that the synthesized PEGylated catalyst was stable and reactive in water. Using 1,5-cyclooctadiene (COD) as monomer, we showed the highly efficient catalyst yielded colloidally stable polymer latexes with ~ 100% conversion at room temperature. Kinetic studies demonstrated first-order kinetics with good livingness as confirmed by the shift of gel permeation chromatography (GPC) traces. Depending on the surfactants used, the particle sizes ranged from 100 to 300 nm with monomodal distributions. The more strained cyclic olefin norbornene (NB) could also be efficiently polymerized with a PEGylated ruthenium alkylidene in miniemulsion to full conversion and with minimal coagulum formation.

Homo e Heterossexuais: o papel das memórias de vergonha, das memórias precoces de calor e segurança, e qualidade de vinculação ao pai, à mãe e ao par amoroso

As experiências precoces de vergonha, na infância e adolescência, cujas memórias assumem características traumáticas, e de centralidade para a identidade, estão associadas a maior propensão para a vergonha e psicopatologia na adultez. O presente estudo visou clarificar o impacto das características traumáticas e da centralidade, das memórias de vergonha, e das memórias precoces de calor e segurança, na qualidade de vinculação aos pais e ao par amoroso, apreciando a orientação sexual. Nesse sentido, 123 sujeitos, homossexuais masculinos (N = 53) e heterossexuais masculinos e femininos (N = 70), completaram a bateria de questionários de autorresposta, para avaliar as caraterísticas traumáticas e a centralidade das memórias de vergonha, as memórias precoces de calor e segurança, a qualidade de vinculação ao pai, à mãe e ao par amoroso, recolhidos a partir de amostra de conveniência não aleatória da população geral. Os resultados mostram que os homossexuais, comparativamente com os heterossexuais, apresentam níveis mais elevados de caraterísticas traumáticas e de centralidade para a identidade, das memórias de vergonha, a par de níveis inferiores de memórias precoces positivas. As caraterísticas traumáticas e de centralidade, das memórias de vergonha, surgem associadas, com intensidade tendencialmente superior nos homossexuais, à restrição da aquisição de autonomia, conferida pelo pai, à sua desvalorização e à ansiedade de separação materna. O vínculo inseguro, aos progenitores, perpetua-se à adultez e ao par amoroso. Relativamente aos heterossexuais, apurámos que o laço emocional e a ansiedade de separação e dependência, paterna e materna, surgem associados a maior confiança e menor evitamento, respetivamente, ao par amoroso. Paralelamente, a ansiedade de separação e dependência materna surge, ainda, associada a maior dependência daquela figura. Este estudo conclui que as experiências precoces de vergonha, na infância e adolescência, podem funcionar como memórias com caraterísticas traumáticas e autobiográficas, constituir marcos de referência centrais no que concerne à identidade e história de vida, sobretudo em homossexuais, com atribuição de significado a outras experiências de vida, nomeadamente no que respeita à vinculação ao par romântico. / Early experiences of shame, in childhood and adolescence, whose memories assume traumatic characteristics, and centrality to identity, are associated with greater propensity to shame and psychopathology in adulthood. The present study aimed to clarify the impact of traumatic features and centrality to identity of shame memories, and of early memories of warmth and safety, on quality of attachment to parents and the loving couple`s bond, considering sexual orientation. Accordingly, 123 subjects, male homosexuals (N = 53) and male and female (N = 70) heterosexuals, completed the battery of self-report questionnaires, to assess trauma characteristics and centrality of shame memories, early memories of warmth and safeness, quality of attachment to the father, mother and loving couple, collected from a non-random convenience sample from general population. The results point that homosexual men, compared with heterosexuals, show higher levels of traumatic characteristics and centrality to identity of shame memories, along with lower levels of early positive memories. Traumatic characteristics and centrality of shame memories arise associated, tendentiously with higher intensity in homosexuals, to restriction of autonomy`s acquisition, conferred by the father, his devaluation and maternal separation anxiety. The unsecured bond, to parents, perpetuates into adulthood and loving couple. Regarding heterosexuals, we found that emotional bond and separation anxiety and dependency, paternal and maternal, arise associated with greater confidence, and less avoidance, respectively, to the loving couple. Further, separation anxiety and mother`s dependency also appears associated with greater dependency to that figure. This study concludes that early experiences of shame, in childhood and adolescence, might function as memories with traumatic and autobiographical characteristics, produce landmarks of central reference regarding identity and life`s history, particularly in homosexual, with attribution of meaning to other life experiences, particularly in the linking to the romantic couple.