Influência da densidade de carga e da massa molar da poliacrilamida na reologia de sistemas microemulsionados

The knowledge of the rheological behavior of microemulsionated systems (SME) is of fundamental importance due to the diversity of industrial applications of these systems. This dissertation presents the rheological behavior of the microemulsionated system formed by RNX 95/alcohol isopropyl/p-toulen sodium sulfonate/kerosene/distilled water with the addition of polyacrylamide polymer. It was chosen three polymers of the polyacrylamide type, which differ in molar weight and charge density. It was studied the addition of these polymers in relatively small concentration 0,1% in mass and maximum concentration of 2,0%. It was made analysis of flow to determine the appearing viscosities of the SME and rheological parameters applying Bingham, Ostwald de Waale and Herschell-Buckley models. The behavior into saline environment of this system was studied for a solution of KCl 2,0%, replacing the distilled water. It was determined the behavior of microemulsions in relation with the temperature through curves of flow in temperatures of 25 to 60ºC in variations of 5ºC. After the analysis of the results the microemulsion without the addition of polymer presented a slight increase in its viscosity, but it does not mischaracterize it as a Newtonian fluid. However the additive systems when analyzed with low concentration of polymer adjusted well to the applied models, with a very close behavior of microemulsion. The higher concentration of the polymer gave the systems a behavior of plastic fluid. The results of the temperature variation point to an increase of viscosity in the systems that can be related to structural changes in the micelles formed in the own microemulsion without the addition of polymer

Retrograde Endovascular Treatment of Internal Iliac Aneurysm in a Patient with Marfan Syndrome

To report a technique to maintain pelvic flow to an internal iliac artery (IIA) with aneurysm in a patient with Marfan syndrome, and previously treated by infrarenal abdominal aortic aneurysm open procedure. Retrograde endovascular hypogastric artery preservation (REHAP) through flexible endograft implantation from external iliac artery (EIA) to internal iliac artery (IIA) was used. REHAP was a reasonable, minimally invasive and elegant alternative (new) to maintain pelvic arterial flow in Marfan syndrome. However, the long-term durability is unknown, and so, it should be used in selected patients.

Gastrointestinal transit and disintegration of enteric coated magnetic tablets assessed by ac biosusceptometry

The oral administration is a common route in the drug therapy and the solid pharmaceutical forms are widely used. Although much about the performance of these formulations can be learned from in vitro studies using conventional methods, evaluation in vivo is essential in product development. The knowledge of the gastrointestinal transit and how the physiological variables can interfere with the disintegration and drug absorption is a prerequisite for development of dosage forms. The aim of this work was to employing the ac biosusceptometry (ACB) to monitoring magnetic tablets in the human gastrointestinal tract and to obtain the magnetic images of the disintegration process in the colonic region. The ac biosusceptometry showed accuracy in the quantification of the gastric residence time, the intestinal transit time and the disintegration time (DT) of the magnetic formulations in the human gastrointestinal tract. Moreover, ac biosusceptometry is a non-invasive technique, radiation-free and harmless to the volunteers, as well as an important research tool in the pharmaceutical, pharmacological and physiological investigations. (c) 2005 Elsevier B.V. All rights reserved.

Clinical Viability for Immediate Loading of Dental Implants: Part II-Treatment Alternatives

The treatment with implants aims to obtain a direct interface between bone and implant. The implant is kept load-free during 4 to 6 months in the 2-stage procedure, which is considered a requisite for osseointegration. However, this period is based on empirical principles and uncomfortable for patient. So, the immediate loading protocol was Suggested to submit implants to occlusal function after placement. This protocol has been applied for several conditions of edentulism. The aim of this study was to evaluate the treatment alternatives for immediate loading of complete and partial edentulous patients. In general, the studies have demonstrated high previsibility for rehabilitation of complete edentulous arches with full-arch, implant-supported prosthesis. The rehabilitation with immediate loading for maxillary overdenture is questionable because there is no longitudinal study in literature. The studies with partial edentulous arches have demonstrated high success rates for implants placed in the mandibular and maxillary anterior region. Additional care is recommended for posterior region mainly in the maxillary arch, and further studies are suggested to corroborate this treatment.

Thermal photon production in Au plus Au collisions: Viscous corrections in two different hydrodynamic formalisms

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Experimental paracoccidioidomycosis in hamster: transmission electron microscopy of inoculation site lesion

Estudou-se sequencialmente, à microscopia eletrônica de transmissão, a interação entre Paracoccidioides brasiliensis (Pb) e células inflamatórias em hamsters inoculados por via intratesticular. Seis horas após inoculações havia predominância de neutrófilos, estando presentes algumas células mononucleares e eosinófilos. Os neutrófilos foram progressivamente substituídos por células mononucleares. Fungos viáveis apresentavam-se fagocitados ou circunscritos por células inflamatórias, geralmente com ampla interface hospedeiro-parasita. Fungos mortos ou degenerados eram acompanhados de interfase estreita. A camada externa da parede do Pb era às vezes quebrada quando em contacto com neutrófilos, em vários pontos, sendo os fragmentos dessa parede descamados e fagocitados. Células fúngicas pequenas com um único núcleo se relacionavam com ampla interfase enquanto as células maiores e multinucleadas apresentavam paredes irregulares, por vezes, contendo lomasoma e/ou estrutura semelhante à mielina. Diferentes padrões de interação do Pb com células do hospedeiro podem ser decorrentes do a fluxo de células inflamatórias funcionalmente diferentes ao local de inoculação ou à idade dos fungos ou ambos os fatores.

Mandioca e Resíduos das Farinheiras na Alimentação de Ruminantes: pH, Concentração de N-NH3 e Eficiência Microbiana

O objetivo do presente trabalho foi avaliar a concentração de N-NH3, o pH do líquido ruminal e a eficiência de síntese microbiana de rações que continham diferentes fontes energéticas: milho (MI), milho + casca de mandioca desidratada (MC), raspa de mandioca (RM) e farinha de varredura de mandioca (FV). Foram utilizados quatro novilhos da raça Holandesa (270 kg), portadores de cânulas ruminal e duodenal, distribuídos em um delineamento Quadrado Latino 4x4. A cinza insolúvel em ácido foi utilizada como indicador do fluxo duodenal e fecal. Não houve efeito das rações experimentais no pH ruminal. No entanto, menor concentração de N-NH3 foi observada para a ração com FV. O fluxo duodenal de matéria orgânica e nitrogênio e a composição química das bactérias ruminais não foram influenciados pelas rações experimentais. A maior eficiência microbiana aparente foi obtida para a ração com FV. Nas condições do presente experimento a FV, possivelmente apresentou uma melhor sincronização com a fonte protéica (farelo de soja), diminuindo a perda de nitrogênio na forma de N-NH3 e aumentando a eficiência microbiana.

Mechanochemical synthesis of ceramic powders with perovskite structure

The mechanical activation is one of the most effective method for obtaining highly disperse system due to mechanical action stress fields form in solids during milling procedure. This effect results in changes of free energy, leading to release of heat, formation of a new surface, formation of different crystal lattice defects and initiation of solid-state chemical reaction. The accumulated deformation energy determines irreversible changes of crystal structure and consequently microstructure resulting in the change of their properties. Mechanochemical processing route has been developed recently for the production of intermetallic and alloy compounds. The intrinsic advantage of this process is that the solid-state reaction is activated due to mechanical energy instead of the temperature. It was shown that the chemical reactivity of starting materials could be improved significantly after mechanochemical activation and, subsequently, the calcination temperature was reduced. Besides, it was apparent that the mechanochemical treatment could enhance the reactivity of constituent oxides; however, the sintering process could not be avoided to develop the desired ceramics. A novel mechanochemical technique for synthesis of fine-grained perovskite structured powders has shown that it is possible to form perovskite at room temperature. The effect of milling on the formation of perovskite structure of barium titanate (BT), lead titanate (PT), PZT, PZN, magnesium niobate (PMN) and LM ceramic materials was analyzed. The dielectric properties of sintered ceramics are comparable with those prepared by other methods in the literature. (C) 2003 Elsevier B.V. B.V. All rights reserved.

Intestinal starch disappearance increased in steers abomasally infused with starch and protein

Steers (379 +/- 10 kg) with ruminal, duodenal, and ileal cannulas were used in a 5 x 5 Latin square digestion trial to quantify and evaluate the relationship between intestinal protein supply and intestinal starch disappearance. Treatments were infusions of 0, 50, 100, 150, or 200 g/d of casein along with 1,042 g/d of raw cornstarch. Abomasal infusions were accomplished by passing tubing and a pliable retaining washer through the reticular-omasal orifice into the abomasum. Steers were fed a 93% corn silage, 7% supplement diet that contained 12% crude protein at 1.65% body weight in 12 equal portions/d. Periods lasted 17 d (12 d for adaptation, 2 d of collections, and 3 d of rest). The quantity and percentage of organic matter and protein disappearance from the small intestine increased linearly (P < 0.03) with infused casein. Greater quantities of starch disappeared with increased casein infusion (P < 0.01). The infusion of 200 g/d of casein increased small intestinal starch disappearance by 226 g/d over the control. Casein infusion did not affect the quantity or percent of organic matter, starch, or protein disappearance in the large intestine. Treatments did not change ruminal ammonia N, ruminal pH, or plasma glucose concentrations. Starch disappearance from the small intestine was increased with greater protein flow to the duodenum of steers.

Oriented growth of Bi3.25La0.75Ti3O12 thin films on RuO2/SiO2/Si substrates by using the polymeric precursor method: Structural, microstructural and electrical properties

c-axis oriented Bi3.25La0.75Ti3O12 (BLT) thin films were grown on a RuO2 top electrode deposited on a (100) SiO2/Si substrate by the polymeric precursor method. X-ray diffraction and atomic force microscope investigations indicate that the films exhibit a dense, well crystallized microstructure having random orientations with a rather smooth surface morphology. The electrical properties of preferred oriented Bi3.25La0.75Ti3O12 (BLT) thin films deposited on RuO2 bottom electrode leaded to a large remnant polarization (P-r ) of 17.2 mu C/cm(2) and (V-c ) of 1.8 V, fatigue free characteristics up to 10(10) switching cycles and a current density of 2.2 mu A/cm(2) at 5 V. We found that the polarization loss is insignificant with nine write/read voltages at a waiting time of 10,000 s. Independently of the applied electric field the retained switchable polarization approached a nearly steady-state value after a retention time of 10 s.

Pressure field along the axis of a high-power klystron amplifier

The pressure field in a high-power klystron amplifier is investigated to scale the ionic vacuum pump used to maintain the ultra high-vacuum in the device in order to increase its life-time. The investigation is conducted using an 1.3 GHz, 100 A - 240 keV high-power klystron with five reentrant coaxial cavities, assembled in a cylindrical drift tube 1.2 m long. The diffusion equation is solved to the regime molecular flow to obtain the pressure profile along the axis of the klystron drift tube. The model, solved by both analytical and numerical procedures, is able to determine the pressure values in steady-state case. This work considers the specific conductance and all important gas sources, as in the degassing of the drift tube and cavities walls, cathode, and collector. For the drift tube degassing rate equals to q(deg) = 2x10(-12) (-)mbar.L.s(-1) cm(-2) (degassing rate per unit area), to cavities q(cavity) = 3x10(-13) mbar.L.s(-1)cm(-2), to the cathode q(cathode) = 6x10(-9)_mbar.L.s(-1) and to the collector q(collector) = 6x10(-9) mbar.L.s(-1), it was found that a 10 L.s(-1) ionic vacuum pump connected in the output waveguide wall is suitable. In this case, the pressure obtained in the cathode is p(cathode) = 6.3x10(-9) mbar, in the collector p(collector) = 2.7x10(-9) mbar, and in the output waveguide p = 2.1x10(-9) mbar. Although only the steady-state case is analyzed, some aspects that may be relevant in a transient situation, for instance, when the beam hits the drift tube walls, producing a gas burst, is also commented.

Ferroelectric properties and leakage current characteristics of Bi3.25La0.75Ti3O12 thin films prepared by the polymeric precursor method

The ferroelectric properties and leakage current mechanisms of preferred oriented Bi3.25La0.75Ti3O12 (BLT) thin films deposited on La0.5Sr0.5CoO3 by the polymeric precursor method were investigated. These films showed excellent ferroelectric properties in terms of large remnant polarization (2P(r)) of 47.6 mu C/cm(2) and (2E(c)) of 55 kV/cm, fatigue-free characteristics up to 10(10) switching cycles, and a current density of 0.7 mu A/cm(2) at 10 kV/cm. X-ray diffraction and scanning electron microscope investigations indicate that the deposited films exhibit a dense, well-crystallized microstructure having random orientations and with a rather smooth surface morphology. The improved ferroelectric and leakage current characteristics can be ascribed to the platelike grains of the BLT films, which make the domain walls easier to be switched under external field.

4 '-Aminochalcones As Novel Inhibitors of the Chlorinating Activity of Myeloperoxidase

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Assessment and statistics of Brazilian hydroelectric power plants: Dam areas versus installed and firm power

The Brazilian relief, predominantly composed by small mountains and plateaus, contributed to formation of rivers with high amount of falls. With exception to North-eastern Brazil, the climate of this country are rainy, which contributes to maintain water flows high. These elements are essential to a high hydroelectric potential, contributing to the choice of hydroelectric power plants as the main technology of electricity generation in Brazil. Though this is a renewable source, whose utilized resource is free, dams must to be established which generates a high environmental and social impact. The objective of this study is to evaluate the impact caused by these dams through the use of environmental indexes. These indexes are ratio formed by installed power with dam area of a hydro power plant, and ratio formed by firm power with this dam area. In this study, the greatest media values were found in South, Southeast, and Northeast regions respectively, and the smallest media values were found in North and Mid-West regions, respectively. The greatest encountered media indexes were also found in dams established in the 1950s. In the last six decades, the smallest indexes were registered by darns established in the 1980s. These indexes could be utilized as important instruments for environmental impact assessments, and could enable a dam to be established that depletes an ecosystem as less as possible.

Forum: social network for the surveillance and prevention of workplace accidents

In 2008, academic researchers and public service officials created a university extension studies platform based on online and on-site meetings denominated "Work-Related Accidents Forum: Analysis, Prevention, and Other Relevant Aspects. Its aim was to help public agents and social partners to propagate a systemic approach that would be helpful in the surveillance and prevention of work-related accidents. This article describes and analyses such a platform. Online access is free and structured to: support dissemination of updated concepts; support on-site meetings and capacity to build educational activities; and keep a permanent space for debate among the registered participants. The desired result is the propagation of a social-technical-systemic view of work-related accidents that replaces the current traditional view that emphasizes human error and results in blaming the victims. The Forum uses an educational approach known as permanent health education, which is based on the experience and needs of workers and encourages debate among participants. The forum adopts a problematizing pedagogy that starts from the requirements and experiences of the social actors and stimulates support and discussions among them in line with an ongoing health educational approach. The current challenge is to turn the platform into a social networking website in order to broaden its links with society.