Adsorption Calorimetry for Energy Conversion Technologies: Applications in Organic Photovoltaics, Catalysis, and Atomic Layer Deposition

Thesis (Ph.D.)--University of Washington, 2016-07

Survery and simulation of energy use in the European building stock

the work towards increased energy efficiency. In order to plan and perform effective energy renovation of the buildings, it is necessary to have adequate information on the current status of the buildings in terms of architectural features and energy needs. Unfortunately, the official statistics do not include all of the needed information for the whole building stock.   This paper aims to fill the gaps in the statistics by gathering data from studies, projects and national energy agencies, and by calibrating TRNSYS models against the existing data to complete missing energy demand data, for countries with similar climate, through simulation. The survey was limited to residential and office buildings in the EU member states (before July 2013). This work was carried out as part of the EU FP7 project iNSPiRe.   The building stock survey revealed over 70% of the residential and office floor area is concentrated in the six most populated countries. The total energy consumption in the residential sector is 14 times that of the office sector. In the residential sector, single family houses represent 60% of the heated floor area, albeit with different share in the different countries, indicating that retrofit solutions cannot be focused only on multi-family houses.   The simulation results indicate that residential buildings in central and southern European countries are not always heated to 20 °C, but are kept at a lower temperature during at least part of the day. Improving the energy performance of these houses through renovation could allow the occupants to increase the room temperature and improve their thermal comfort, even though the potential for energy savings would then be reduced.

Air Temperature Distribution and Energy-balance Modelling of a Debris-covered Glacier

Near-surface air temperature is an important determinant of the surface energy balance of glaciers and is often represented by a constant linear temperature gradients (TGs) in models. Spatiotemporal variability in 2 m air temperature was measured across the debris-covered Miage Glacier, Italy, over an 89 d period during the 2014 ablation season using a network of 19 stations. Air temperature was found to be strongly dependent upon elevation for most stations, even under varying meteorological conditions and at different times of day, and its spatial variability was well explained by a locally derived mean linear TG (MG–TG) of −0.0088°C m−1. However, local temperature depressions occurred over areas of very thin or patchy debris cover. The MG–TG, together with other air TGs, extrapolated from both on- and off-glacier sites, were applied in a distributed energy-balance model. Compared with piecewise air temperature extrapolation from all on-glacier stations, modelled ablation, using the MG–TG, increased by <1%, increasing to >4% using the environmental ‘lapse rate’. Ice melt under thick debris was relatively insensitive to air temperature, while the effects of different temperature extrapolation methods were strongest at high elevation sites of thin and patchy debris cover.

A long-term energy efficiency prediction model for the Brazilian automotive industry

According to law number 12.715/2012, Brazilian government instituted guidelines for a program named Inovar-Auto. In this context, energy efficiency is a survival requirement for Brazilian automotive industry from September 2016. As proposed by law, energy efficiency is not going to be calculated by models only. It is going to be calculated by the whole universe of new vehicles registered. In this scenario, the composition of vehicles sold in market will be a key factor on profits of each automaker. Energy efficiency and its consequences should be taken into consideration in all of its aspects. In this scenario, emerges the following question: which is the efficiency curve of one automaker for long term, allowing them to adequate to rules, keep balancing on investment in technologies, increasing energy efficiency without affecting competitiveness of product lineup? Among several variables to be considered, one can highlight the analysis of manufacturing costs, customer value perception and market share, which characterizes this problem as a multi-criteria decision-making. To tackle the energy efficiency problem required by legislation, this paper proposes a framework of multi-criteria decision-making. The proposed framework combines Delphi group and Analytic Hierarchy Process to identify suitable alternatives for automakers to incorporate in main Brazilian vehicle segments. A forecast model based on artificial neural networks was used to estimate vehicle sales demand to validate expected results. This approach is demonstrated with a real case study using public vehicles sales data of Brazilian automakers and public energy efficiency data.

Energy systems analysis of transboundary river basins in a nexus approach: the Sava river basin study case

Resource management policies are frequently designed and planned to target specific needs of particular sectors, without taking into account the interests of other sectors who share the same resources. In a climate of resource depletion, population growth, increase in energy demand and climate change awareness, it is of great importance to promote the assessment of intersectoral linkages and, by doing so, understand their effects and implications. This need is further augmented when common use of resources might not be solely relevant at national level, but also when the distribution of resources ranges over different nations. This dissertation focuses on the study of the energy systems of five south eastern European countries, which share the Sava River Basin, using a water-food(agriculture)-energy nexus approach. In the case of the electricity generation sector, the use of water is essential for the integrity of the energy systems, as the electricity production in the riparian countries relies on two major technologies dependent on water resources: hydro and thermal power plants. For example, in 2012, an average of 37% of the electricity production in the SRB countries was generated by hydropower and 61% in thermal power plants. Focusing on the SRB, in terms of existing installed capacities, the basin accommodates close to a tenth of all hydropower capacity while providing water for cooling to 42% of the net capacity of thermal power currently in operation in the basin. This energy-oriented nexus study explores the dependency on the basin’s water resources of the energy systems in the region for the period between 2015 and 2030. To do so, a multi-country electricity model was developed to provide a quantification ground to the analysis, using the open-source software modelling tool OSeMOSYS. Three main areas are subject to analysis: first, the impact of energy efficiency and renewable energy strategies in the electricity generation mix; secondly, the potential impacts of climate change under a moderate climate change projection scenario; and finally, deriving from the latter point, the cumulative impact of an increase in water demand in the agriculture sector, for irrigation. Additionally, electricity trade dynamics are compared across the different scenarios under scrutiny, as an effort to investigate the implications of the aforementioned factors in the electricity markets in the region.

Responses to various protein and energy supplements by steers fed low-quality tropical hay. 1. Comparison of response surfaces for young steers

Response curves were established for different supplements, offered at intakes ranging from 0 to 20 g/kg liveweight (W).day to young Bos indicus crossbred steers fed low-quality Rhodes grass (Chloris gayana) hay ad libitum in two pen experiments. Supplements included protein meals of varying rumen-degradability (cottonseed meal (CSM) or fishmeal), as well as ‘energy sources’ comprising grains of high and low ruminal starch degradability (barley and sorghum) and a highly fermentable sugar source (molasses), with all diets adjusted for rumen-degradable nitrogen and mineral content. Unsupplemented steers gained 0.08 and 0.15 kg/day, in Experiments 1 and 2, respectively. Growth of steers increased linearly with intake of ‘energy source’ supplements in increasing order of molasses, sorghum and barley (all differences P < 0.05). Steer growth rate also increased linearly with fishmeal, albeit over a narrow intake range (0–4.1 g/kg W.day), whereas the response with CSM was asymptotic, showing a steep response at low intake before levelling at ~1.2 kg/day. All supplement types were associated with a linear reduction in hay intake by the steers (energy substitution) where the reduction was greater (P < 0.05) for barley and molasses (not different) than for sorghum (P < 0.05), and for fishmeal compared with CSM (P < 0.05). In concurrent metabolism studies with the same rations, organic matter digestibility of the total ration (561–578 g/kg DM, unsupplemented) was increased linearly by barley and molasses (both P < 0.05) but was unaffected by CSM and sorghum supplements. The efficiency of microbial protein synthesis in steers increased linearly, from 91 g microbial crude protein/kg digestible organic matter (unsupplemented), in both molasses and CSM-supplemented steers, with the trend for a higher response to molasses (P = 0.05), and appeared most closely related to digestible organic matter intake. The response curves from these studies provide the practical framework upon which to formulate rations for cattle grazing low-quality forages.

The impact of the MARINET initiative on the development of Marine Renewable Energy

Marine Renewable Energy Conversion systems comprise wave energy and tidal stream converters as well as offshore-wind turbines for electrical generation. These technologies are currently at different stages of development but are mostly at the pre-commercial stage and require research to be undertaken at a series of scales along the path to commercialization. However each of these technologies also needs specific research infrastructures in order to conduct this research. The aim of the MARINET initiative is to coordinate research and development at all scales (small models through to prototype scales, from laboratories through to open sea tests) and to allow access for researchers and developers to infrastructures which are not available universally in Europe, including test facilities for components such as power take-off systems, grid integration, moorings and environmental monitoring so as to ensure a focusing of activities in this area. The initiative offers researchers and developers access to 45 research facilities as well as to the associated network of expertise at all scales in Offshore Marine Renewable Energy technology research and development. The aim of this paper is to present this MARINET initiative that was started in 2011, bringing together a network of 29 partners spread across twelve countries. Details of the MARINET Transnational Access (TA) program are presented, for which over 260 applications were received throughout the 5 official calls for proposals. In particular, statistics on applications and completed projects are presented which provide an overview of the global development progress of the different offshore renewable energy conversion technologies at a European level. It also provides a good overview of the current research activity, as well as evidence of the requirement for specialised research facilities, in this burgeoning field.

Responses to various protein and energy supplements by steers fed low-quality tropical hay. 2. Effect of stage of maturity of steers

Dose response curves to various supplements were established in two pen-feeding experiments (Exp1 and Exp2) with Bos indicus crossbred steers of two age groups (Young, 10–12 months; Old, 33–36 months) fed low-quality tropical grass hays ad libitum. Diets included supplements based on (Exp1) cottonseed meal (CSM; intake (as fed) 0–10 g/kg liveweight (W).day) and a barley mix (Bar; 0–20 g/kg W.day) and (Exp2) a molasses mix (MUP) and a Bar mix, both fed at 0–20 g/kg W.day. Urea was provided with the Bar mixes and urea/copra meal with the MUP mix. Growth rates of Young steers increased linearly with Bar and MUP supplements but asymptotically with CSM whereas those of Old steers increased asymptotically with all supplement types. With supplement intake expressed on a liveweight basis (g/kg W.day), responses were greater for both steer age groups with CSM compared with Bar (Young, P < 0.001; Old, P < 0.01) and Bar compared with MUP treatments (Young, P < 0.01; Old, P < 0.05). Furthermore, Old steers outperformed their Young counterparts with both CSM (P < 0.05) and Bar (P < 0.001) supplements fed in Exp1 and with Bar and MUP supplements (P < 0.01) fed in Exp2. When supplement intake was expressed in absolute terms (kg/day), growth responses were not different between age groups for different supplements except that Old steers had a higher daily W gain on Bar than their Young counterparts (P < 0.05). Intake of hay (W-corrected) was higher for Young compared with Old steers without supplement but was variably reduced for both steer groups with increasing supplement intake. The results of these experiments have implications for supplement formulation for steers at different stages of maturity grazing low-quality forages.

Tidal Energy ”Round Robin” Tests Comparisons between towing tank and circulating tank results

One key step of the industrial development of a tidal energy device is the testing of scale prototype devices within a controlled laboratory environment. At present, there is no available experimental protocol which addresses in a quantitative manner the differences which can be expected between results obtained from the different types of facilities currently employed for this type of testing. As a consequence, where differences between results are found it has been difficult to confirm the extent to which these differences relate to the device performance or to the test facility type. In the present study, a comparative ”Round Robin” testing programme has been conducted as part of the EC FP VII MaRINET program in order to evaluate the impact of different experimental facilities on the test results. The aim of the trials was to test the same model tidal turbine in four different test facilities to explore the sensitivity of the results to the choice of facility. The facilities comprised two towing tanks, of very different size, and two circulating water channels. Performance assessments in terms of torque, drag and inflow speed showed very similar results in all facilities. However, expected differences between the different tank types (circulating and towing) were observed in the fluctuations of torque and drag measurements. The main facility parameters which can influence the behaviour of the turbine were identified; in particular the effect of blockage was shown to be significant in cases yielding for high thrust coefficients, even at relatively small blockage ratios.

In vivo and in vitro disappearance of energy and nutrients in novel carbohydrates and cereal grains by pigs

In vivo and in vitro experiments were conducted to determine digestibility of GE and nutrients, as well as DE and ME of carbohydrates fed to growing pigs. The objective of Exp. 1 was to determine the DE and ME of 4 novel carbohydrates fed to pigs. The 4 novel carbohydrates were 2 sources of resistant starch (RS 60 and RS 70), soluble corn fiber (SCF), and pullulan. These carbohydrates were produced to increase total dietary fiber (TDF) intake by humans. Maltodextrin (MD) was used as a highly digestible control carbohydrate. The DE and ME for RS 60 (1,779 and 1,903 kcal/kg, respectively), RS 75(1,784 and 1,677 kcal/kg, respectively), and SCF (1,936 and 1,712 kcal/kg, respectively) were less (P < 0.05) than for MD (3,465 and 3,344 kcal/kg, respectively) and pullulan (2,755 and 2,766 kcal/kg, respectively), and pullulan contained less (P < 0.05) DE and ME than MD. However, there was no difference in the DE and ME for RS 60, RS 75, and SCF. The varying degrees of small intestinal digestibility and differences in fermentability among these novel carbohydrates may explain the differences in the DE and ME among carbohydrates. Therefore, the objectives of Exp. 2 were to determine the effect of these 4 novel carbohydrates and cellulose on apparent ileal (AID) and apparent total tract (ATTD) disappearance, and hindgut disappearance (HGD) of GE, TDF, and nutrients when added to diets fed to ileal-cannulated pigs. The second objective was to measure the endogenous flow of TDF to be able to calculate the standardized ileal disappearance (SID) and standardized total tract (STTD) disappearance of TDF in the 4 novel fibers fed to pigs. Results of the experiment indicated that the AID of GE and DM in diets containing cellulose or the novel fibers was less (P < 0.05) than of the maltodextrin diet, but the ATTD of GE and DM was not different among diets. The addition of RS 60, RS 75, and SCF did not affect the AID of acid hydrolysed ether extract (AEE), CP, or ash, but the addition of cellulose and pullulan reduced (P < 0.01) the AID of CP. The average ileal and total tract endogenous losses of TDF were calculated to be 25.25 and 42.87 g/kg DMI, respectively. The SID of TDF in diets containing RS 60, SCF, and pullulan were greater (P < 0.01) than the SID of TDF in the cellulose diet, but the STTD of the SCF diet was greater (P < 0.05) than for the cellulose and pullulan diets. Results of this experiment indicate that the presence of TDF reduces small intestinal disappearance of total carbohydrates and energy which may reduce the DE and ME of diets and ingredients. Therefore, the objective of Exp. 3 was to determine the DE and ME in yellow dent corn, Nutridense corn, dehulled barley, dehulled oats, polished rice, rye, sorghum, and wheat fed to growing pigs and to determine the AID and ATTD of GE, OM, CP, AEE, starch, total carbohydrates, and TDF in these cereal grains fed to pigs. Results indicated that the AID of GE, OM, and total carbohydrates was greater (P < 0.001) in rice than in all other cereal grains. The AID of starch was also greater (P < 0.001) in rice than in yellow dent corn, dehulled barley, rye, and wheat. The ATTD of GE was greater (P < 0.001) in rice than in yellow dent corn, rye, sorghum, and wheat. With a few exceptions, the AID and ATTD of GE and nutrients in Nutridense corn was not different from the values for dehulled oats. Likewise, with a few exceptions, the AID, ATTD, and HGD of GE, OM, total carbohydrates, and TDF in yellow corn, sorghum, and wheat were not different from each other. The AID of GE and AEE in dehulled barley was greater (P < 0.001) than in rye. The ATTD of GE and most nutrients was greater (P < 0.001) in dehulled barley than in rye. Dehulled oats had the greatest (P < 0.001) ME (kcal/kg DM) whereas rye had the least ME (kcal/kg DM) among the cereal grains. Results of the experiment indicate that the presence of TDF and RS may reduce small intestinal digestibility of starch in cereal grains resulting in reduced DE and ME in these grains. Digestibility experiments involving animals are time consuming and expensive. Therefore, the objective of Exp. 4 was to correlate DM and OM digestibility obtained from 3 in vitro procedures with ATTD of GE and with the concentration of DE in 50 corn samples that were fed to growing pigs. The second objective was to develop a regression model that can predict the ATTD of GE or the concentration of DE in corn. The third objective was to evaluate the suitability of using the DaisyII incubator as an alternative to the traditional water bath when determining in vitro DM and OM digestibility. Results indicated that corn samples incubated with Viscozyme for 48 h in the DaisyII incubator improved (P < 0.001) the ability of the procedure to detect small differences in the ATTD of GE or to detect small differences in the concentration of DE in corn. Likewise, compared with using cellulase or fecal inoculum, the variability in the ATTD of GE and the variability in the DE in corn was better (R2 = 0.56; P < 0.05 and R2 = 0.53; P < 0.06, respectively) explained if Viscozyme was used than if cellulase or fecal inoculum was used. A validated regression model that predicted the DE in corn was developed using Viscozyme and with the corn samples incubated in the DaisyII incubator for a 48 h. In conclusion, this present work used the pig as a model for human gastrointestinal function and evaluates carbohydrates from 2 different nutritional perspectives – humans and animals. The addition of novel carbohydrates reduced the digestibility of energy in the diets without necessarily reducing the digestibility of other nutrients. Thus, supplementation of novel carbohydrates in the diets may be beneficial for the management of diabetes. Aside from diabetic management, cereal grains such as rye and sorghum, may also help in BW management because of there low caloric value, but for undernourished individuals, dehulled oats, dehulled barley, and rice are the ideal grains. From an animal nutrition standpoint, high concentration of dietary fiber is undesirable because it reduces feed efficiency. Therefore, the inclusion of feed ingredients that have a high concentration of dietary fiber is often limited in animal diets. Although in vivo determination is ideal, in vitro procedures are useful tools to determine caloric value of food and feed ingredients.

All-regime Lagrangian-Remap numerical schemes for the gas dynamics equations. Applications to the large friction and low Mach coefficients

In this talk, we propose an all regime Lagrange-Projection like numerical scheme for the gas dynamics equations. By all regime, we mean that the numerical scheme is able to compute accurate approximate solutions with an under-resolved discretization with respect to the Mach number M, i.e. such that the ratio between the Mach number M and the mesh size or the time step is small with respect to 1. The key idea is to decouple acoustic and transport phenomenon and then alter the numerical flux in the acoustic approximation to obtain a uniform truncation error in term of M. This modified scheme is conservative and endowed with good stability properties with respect to the positivity of the density and the internal energy. A discrete entropy inequality under a condition on the modification is obtained thanks to a reinterpretation of the modified scheme in the Harten Lax and van Leer formalism. A natural extension to multi-dimensional problems discretized over unstructured mesh is proposed. Then a simple and efficient semi implicit scheme is also proposed. The resulting scheme is stable under a CFL condition driven by the (slow) material waves and not by the (fast) acoustic waves and so verifies the all regime property. Numerical evidences are proposed and show the ability of the scheme to deal with tests where the flow regime may vary from low to high Mach values.

Design and construction of a two dimensional duct equipped with a wave generator and a variable coastal slope and an ocean wave energy conversion system (OWC)

The aims of this thesis were evaluation the type of wave channel, wave current, and effect of some parameters on them and identification and comparison between types of wave maker in laboratory situations. In this study, designing and making of two dimension channels (flume) and wave maker for experiment son the marine buoy, marine building and energy conversion systems were also investigated. In current research, the physical relation between pump and pumpage and the designing of current making in flume were evaluated. The related calculation for steel building, channels beside glasses and also equations of wave maker plate movement, power of motor and absorb wave(co astal slope) were calculated. In continue of this study, the servo motor was designed and applied for moving of wave maker’s plate. One Ball Screw Leaner was used for having better movement mechanisms of equipment and convert of the around movement to linear movement. The Programmable Logic Controller (PLC) was also used for control of wave maker system. The studies were explained type of ocean energies and energy conversion systems. In another part of this research, the systems of energy resistance in special way of Oscillating Water Column (OWC) were explained and one sample model was designed and applied in hydrolic channel at the Sheikh Bahaii building in Azad University, Science and Research Branch. The dimensions of designed flume was considered at 16 1.98 0. 57 m which had ability to provide regular waves as well as irregular waves with little changing on the control system. The ability of making waves was evaluated in our designed channel and the results were showed that all of the calculation in designed flume was correct. The mean of error between our results and theory calculation was conducted 7%, which was showed the well result in this situation. With evaluating of designed OWC model and considering of changes in the some part of system, one bigger sample of this model can be used for designing the energy conversion system model. The obtained results showed that the best form for chamber in exit position of system, were zero degree (0) in angle for moving below part, forty and five (45) degree in front wall of system and the moving forward of front wall keep in two times of height of wave.

A kinetic energy budget and internal instabilities in the Fine Resolution Antarctic Model

An energy analysis of the Fine Resolution Antarctic Model (FRAM) reveals the instability processes in the model. The main source of time-mean kinetic energy is the wind stress and the main sink is transfer to mean potential energy. The wind forcing thus helps maintain the density structure. Transient motions result from internal instabilities of the Bow rather than seasonal variations of the forcing. Baroclinic instability is found to be an important mechanism in FRAM. The highest values of available potential energy are found in the western boundary regions as well as in the Antarctic Circumpolar Current (ACC) region. All subregions with predominantly zonal flow are found to be baroclinically unstable. The observed deficit of eddy kinetic energy in FRAM occurs as a result of the high lateral friction, which decreases the growth rates of the most unstable waves. This high friction is required for the numerical stability of the model and can only be made smaller by using a finer horizontal resolution. A grid spacing of at least 10-15 km would be required to resolve the most unstable waves in the southern part of the domain. Barotropic instability is also found to be important for the total domain balance. The inverse transfer (that is, transfer from eddy to mean kinetic energy) does not occur anywhere, except in very localized tight jets in the ACC. The open boundary condition at the northern edge of the model domain does not represent a significant source or sink of eddy variability. However, a large exchange between internal and external mode energies is found to occur. It is still unclear how these boundary conditions affect the dynamics of adjacent regions.

Update on the correlation of the highest energy cosmic rays with nearby extragalactic matter

Data collected by the Pierre Auger Observatory through 31 August 2007 showed evidence for anisotropy in the arrival directions of cosmic rays above the Greisen-Zatsepin-Kuz'min energy threshold, 6 x 10(19) eV. The anisotropy was measured by the fraction of arrival directions that are less than 3.1 degrees from the position of an active galactic nucleus within 75 Mpc (using the Veron-Cetty and Veron 12th catalog). An updated measurement of this fraction is reported here using the arrival directions of cosmic rays recorded above the same energy threshold through 31 December 2009. The number of arrival directions has increased from 27 to 69, allowing a more precise measurement. The correlating fraction is (38(-6)(+7))%, compared with 21% expected for isotropic cosmic rays. This is down from the early estimate of (69-(+11)(13))%. The enlarged set of arrival directions is examined also in relation to other populations of nearby extragalactic objects: galaxies in the 2 Microns All Sky Survey and active galactic nuclei detected in hard X-rays by the Swift Burst Alert Telescope. A celestial region around the position of the radiogalaxy Cen A has the largest excess of arrival directions relative to isotropic expectations. The 2-point autocorrelation function is shown for the enlarged set of arrival directions and compared to the isotropic expectation. (C) 2010 Elsevier B.V. All rights reserved.