Effect of the curing conditions of concrete on the behaviour under freeze-thaw cycles*

The aim of this work is to relate the curing conditions of concrete and the addition of an air-entraining admixture with the damage caused by freeze–thaw cycles. In countries with a continental climate, the curing of concrete in summer is performed under climatic conditions of high temperature and low humidity, and during the winter the concrete suffers conditions of freeze–thaw, often accompanied by the use of de-icing salts. This paper shows the experimental results of the behaviour of concrete specimens cured under climatic summer conditions (high temperature and low humidity) and then subjected to freeze–thaw cycles. Curing of the specimens includes conditions of good and bad practice in relation to wetting and protection of the concrete. It also examines the effectiveness of using an air-entraining admixture in both cases. The experimental programme includes an evaluation of the mechanical properties of the concrete, the study of the cement hydration and the measurement of the volume and pore sizes of the concrete. These tests were performed before and after the application of the freeze–thaw cycles. The results obtained showed that the specimens without air-entraining admixture show a deterioration of mechanical properties after the freeze–thaw test. However, the inclusion of air bubbles benefits the behaviour of concrete against freeze–thaw cycles so even better mechanical properties after the test were observed. This anomalous behaviour is because the cement hydration process continues over the freeze–thaw tests, closing the pore structure. This aspect has been confirmed with the DTA and TG tests performed

Experimental determination of the eutectic temperature in air of the CuO-TiO2 pseudobinary system

Eutectic temperature and composition in the CuO–TiO2 pseudobinary system have been experimentally determined in air by means differential thermal analysis (DTA), thermogravimetry (TG) and hot-stage microscopy (HSM). Samples of the new eutectic composition treated at different temperatures have been characterized by X-ray diffraction (XRD) and X-ray absorption near-edge structural spectroscopy (XANES) to identify phases and to determine the Cu valence state, respectively. The results show that the eutectic temperature in air is higher by 100 °C (∼1000 °C) for a Ti-richer composition (XTiO2=25 mol%) than the one calculated in the literature. The reduction of Cu2+ to Cu+ takes places at about 1030 °C. The existence of Cu2TiO3 and Cu3TiO4 has been confirmed by XRD in the temperature range between 1045 and 1200 °C.

Estructura y pruebas con Labmu

La implantación de la televisión digital en España ha supuesto un conjunto de desafíos técnicos y de orden práctico que se han ido acometiendo en multitud de ámbitos, desde la legislación que normaliza las infraestructuras comunes de telecomunicación hasta los cambios en las instalaciones y receptores donde el usuario final recibe los servicios. Por la complejidad y el carácter interdisciplinar de los conocimientos necesarios el aprendizaje de los titulados dentro del ámbito de la Telecomunicación supone también un reto importante. Este proyecto realiza una primera aproximación a un conjunto de herramientas hardware y software de ayuda a la enseñanza de esta amplia disciplina. El proyecto se ha realizado en torno a Labmu laboratorio multiusuario para prácticas de televisión digital de la empresa Xpertia. Se ha realizado para conocer y documentar sus posibilidades. También se ha documentado la tarjeta moduladora DTA-111 y el software para Windows StreamXpress. Estos sistemas ofrecen muchas posibilidades para la docencia de la televisión digital en todas las áreas desde la codificación fuente hasta la decodificación en el usuario final. En particular para ambos sistemas se han realizado pruebas en radiofrecuencia de emisiones de TDT. También se han establecido algunas ideas para trabajo futuro con estos sistemas. El proyecto se divide en seis capítulos: Capitulo 1: En el primer capítulo titulado Introducción se presenta el proyecto. Capítulo 2: En el segundo capítulo titulado Composición Hardware Labmu se presentan todos los componentes del laboratorio Labmu con la descripción de cada componente y sus características técnicas. Así mismo se presenta el interconexionado y configuración con que se ha trabajado. Capítulo 3: En el tercer capítulo titulado Software Labmu se describe como manual de usuario todos los componentes y posibilidades de software de Labmu. Capítulo 4: En el cuarto capítulo titulado Medidas con Labmu se realiza las medidas de MER, CBER, VBER, C/N y potencia de canal de los canales emitidos en la Comunidad de Madrid, comparando estas medidas con el analizador Promax Prodig-5. Capítulo 5: En el quinto capítulo titulado Tarjeta receptora y software se describe la tarjeta DTA-111 y el software StreamXpress, realizando medidas con el analizador Promax Prodig-5 introduciendo errores a la señal emitida por la tarjeta, y estudiando los niveles límites de visualización correcta. Capítulo 6: En el sexto y último capítulo titulado Conclusiones se presentan las conclusiones del proyecto y un plan de trabajo futuro ABSTRACT. The implantation of Digital Television in Spain (TDT) has implied a number of technical and practical challenges in several scopes. These challenges range from recommendations that standardize common telecommunications infrastructure to the changes in facilities where the end user receives digital services. The complexity and the interdisciplinary nature of skills that graduate Telecommunications students need to learn, is also a major challenge. This project is a first approach of a set of hard ware and software tools to help in the task of teaching this broad range discipline. The project has been carried out on Labmu, a multiuser Digital Television laboratory created by the Xpertia company. Its objectives are to understand and document this range of possibilities. DTA-111 modulator card and software for Windows StreamXpress have also been documented. These systems offer many options for teaching digital television in all areas, from source coding to end user decoding. In particular, both systems were tested on RF emissions in TDT. More over some ideas for future work with these systems have also foreseen. The project is structured in six chapters: Chapter1: This section Introduces the project. Chapter2: Titled “The Composition Hardware Labmu” presents Labmu lab components and provides descriptions for each component and its technical characteristics. It also presents the interconnection and configuration we have been using. Chapter3: Titled “Software Labmu” is a user manual, describing all components and software possibilities Labmu offers. Chapter4: Titled “Measures to Labmu” presents MER, CBER, VBER, C /N and channel power measures provided by Labmu in comparison with Promax Prodig-5 measures for all channels broad casting digital television services in the Community of Madrid. Chapter 5 Titled “Receiver card and software” describes DTA-111 card and software StreamXpress. Also the effects of errors insertion performed by this card are measured with the PromaxProdig-5 meter. Threes hold levels for correct reception are also studied. Chapter6: Entitled Conclusions presents the conclusions of the project and a plan for future work.

Desarrollo y caracterización de un material celular de alta porosidad con base cementicia activada mediante agentes inorgánicos

Esta tesis ha estudiado los morteros celulares, centrándose en la experimentación con pastas de cemento aireadas (PCA) con polvo de aluminio como agente expansor. El objetivo es el desarrollo de un material cementicio con una baja conductividad térmica que sirva como aislamiento térmico. La naturaleza inorgánica del material lo hace incombustible, en contraste con las espumas poliméricas existentes en el mercado, cuya aplicación en cámaras ventiladas ha sido prohibida por normativas de construcción tanto a nivel nacional como internacional. Las posibles aplicaciones son con proyección neumática o en paneles prefabricados. Se han ensayado dos series de pastas de cemento con polvo de aluminio: - Serie WPC/CAC/CH. Mezcla de referencia con cemento blanco (WPC), cemento de aluminato cálcico (CAC) y cal aérea (CH) en proporción 5:1:4. - Serie OPC/CH. Mezcla de referencia con cemento portland con cenizas volantes (OPC) y cal aérea (CH) en proporción OPC/CH de 4:1 A las mezclas de referencia se le han añadido adiciones de metacaolín (MK) (10 y 20%) o sepiolita (SP) (1 y 2%) para observar el efecto que producen tanto en el mortero fresco como en el mortero endurecido. Se ha estudiado la reología de las pastas en estado fresco, analizando el proceso de expansión de las pastas, registrando los valores de tensión de fluencia, aire ocluido y temperatura durante la expansión. Con los valores obtenidos se ha discutido la influencia de las adiciones utilizadas en la cinética de corrosión del polvo de aluminio que genera la expansión, concluyendo que las adiciones puzolánicas (CV y MK) y la SP reducen mucho el periodo de inducción, lo que provoca poros más grandes y mayor cantidad de aire ocluido. Asimismo se ha analizado la relación entre la tensión de fluencia y el contenido de aire ocluido, deduciendo que a mayor tensión de fluencia en el momento de iniciarse la expansión, menor tamaño de poros y contenido de aire ocluido. Finalmente, se han obtenido las densidades y capacidades de retención de agua de los morteros frescos. Para caracterizar la red porosa de las pastas aireadas endurecidas, se obtuvieron tanto las densidades reales, netas, aparentes y relativas como las porosidades abiertas, cerradas y totales con ensayos hídricos. Finalmente se obtuvieron imágenes de los poros con tomografía axial computerizada para obtener las porosimetrías de las muestras. La caracterización de la red porosa ha servido para terminar de analizar lo observado en la evolución de la expansión del mortero fresco. Se ha analizado la influencia de la red porosa en la conductividad térmica, obtenida con caja caliente, comparándola con la existente en la literatura existente tanto de morteros celulares como de espumas poliméricas. Se concluye que los valores de conductividad térmica conseguida están en el mínimo posible para un material celular de base cementicia. La microestructura se ha estudiado con microscopía electrónica de barrido, difracción de rayos X y ensayos térmicos TG/ATD, observando que los productos de hidratación encontrados coinciden con los que se producen en morteros sin airear. Las imágenes SEM y los resultados de ultrasonidos han servido para analizar la presencia de microfisuras de retracción en las pastas aireadas, observando que en las muestras con adiciones de MK y SP, se reduce la presencia de microfisuras. ABSTRACT This thesis has studied cellular mortars, focusing in testing aerated cement pastes with aluminum powder as expansive agent. The purpose is the development of a cementitious material with low thermal conductivity that can be used as thermal isolation. Inorganic nature of this material makes it non-combustible, in contrast with polymeric foams in market, whose application in ventilated double skin façade systems has been banned by building standards, both domestically and internationally. Possible uses for this material are pneumatically sprayed applications and precast panels. Two series of batches with aluminum powder have been tested: - WPC/CAC/CH series. Reference paste with white portland cement (WPC), calcium aluminate cement (CAC) and lime (CH) with 5:1:4 ratio. - OPC/CH series. Reference paste with portland cement with fly ash (OPC) and lime (CH) with 4:1 ratio. Metakaolin (MK) (10 and 20%) or sepiolite (SP) (1 and 2%) additions were used in reference pastes to characterize the effect in fresh and hardened mortar. Rheology in fresh pastes was studied, expansion process of pastes was analyzed, recording yield stress, entrained air and temperature values during expansion. Recorded values were used to discuss influence of additions on reaction kinetics of aluminum powder corrosion, that produces expansion.. Conclusion is that pozzolanic additions (FA and MK) and SP greatly reduce induction period, producing bigger pores and more entrained air. Relation between yield stress and entrained air has been also analyzed, observing that the bigger yield stress at beginning of expansion, the smaller pores size and the lower entrained air values. Finally density and water retention of fresh mortars were obtained. Pore network in hardened aerated cement pastes was characterized by imbibition methods providing true, bulk and relative density, and providing also open, closed and total porosity. Finally, pore system imaging were obtained with computerized axial tomography to study porosimetry of specimens. Pore network characterization was useful to complete facts analysis observed in expansion of fresh mortars. Influence of pore network in thermal conductivity, checked in hot box, was analyzed comparing with those existing values in cellular mortar and polymeric foams researches. It was concluded that thermal conductivity values achieved are close to minimum possible in a cementitious cellular material. Microstructure was studied with Scanning Electron Microscopy, X-Ray Diffractometry and TG-DTA analysis, observing that hydration phases found, are those produced in non aerated mortar. SEM imaging and ultrasound results were useful to analyze shrinkage microcracks in aerated cement pastes, concluding that microcrack presence in specimens with MK and SP additions were reduced.

Estudio microestructural y de los procesos de hidratación de cementos con adiciones

En los últimos años, las sociedades industrializadas han tomado una mayor conciencia sobre el problema que suponen las emisiones indiscriminadas de gases de efecto invernadero a la atmósfera. El hormigón, cuyo principal componente es el cemento, es probablemente el material más utilizado en construcción. En la actualidad, las emisiones globales de CO2 debidas a la combustión del CaCO3 del cemento Pórtland representan entre el 5% y el 10% respecto del total. Estos valores son de gran interés si se considera que el compromiso aceptado al firmar el Protocolo de Kioto es de una reducción del 5% antes del año 2020, sobre el total de gases producidos. El principal objetivo del presente trabajo es el estudio microestructural y de los procesos de hidratación de los cementos con adiciones. Para ello se propone contribuir a la investigación sobre nuevos productos cementicios basados en micropartículas esféricas vítreas que pueden adicionarse al cemento antes del proceso de amasado. Los resultados obtenidos se han contrastado con las adiciones convencionales de más uso en la actualidad. El nuevo material basa su composición en la química del aluminio y el silicio. Al disminuir la cantidad de CaCO3, se contribuye al desarrollo sostenible y a la reducción de emisiones de CO2. La patente creada por el Grupo Cementos Pórtland Valderrivas (GCPV), describe el proceso de producción de las cemesferas (WO 2009/007470, 2010). Los productos que forman la materia prima para la elaboración de las cemesferas son arcillas, calizas, margas o productos o subproductos industriales, que tras su molienda, son fundidos mediante un fluido gaseoso a elevada temperatura (entre 1250ºC y 1600ºC). Este proceso permite obtener un producto final en forma esférica maciza o microesfera, que tras estabilizarse mediante un enfriamiento rápido, consigue una alta vitrificación idónea para su reactividad química, con una mínima superficie específica en relación a su masa. El producto final obtenido presenta prácticamente la finura requerida y no precisa ser molido, lo que reduce las emisiones de CO2 por el ahorro de combustible durante el proceso de molienda. El proceso descrito permite obtener un amplio abanico de materiales cementantes que, no solo pueden dar respuesta a los problemas generados por las emisiones de CO2, sino también a la disponibilidad de materiales en países donde hasta el momento no se puede fabricar cemento debido a la falta de calizas. Complementariamente se ha optimizado el método de cálculo del grado de hidratación a partir de los resultados del ensayo de ATD-TG en base a los modelos de cálculo de Bhatty y Pane. El método propuesto permite interpretar el comportamiento futuro del material a partir de la interpolación numérica de la cantidad de agua químicamente enlazada. La evolución del grado de hidratación tiene una relación directa con el desarrollo de la resistencia mecánica del material. Con el fin de caracterizar los materiales de base cemento, se ha llevado a cabo una amplia campaña experimental en pasta de cemento, mortero y hormigón. La investigación abarca tres niveles: caracterización microestructural, macroestructural y caracterización del comportamiento a largo plazo, fundamentalmente durabilidad. En total se han evaluado ocho adiciones diferentes: cuatro adiciones convencionales y cuatro tipos de cemesferas con diferente composición química. Los ensayos a escala microscópica comprenden la caracterización química, granulométrica y de la superficie específica BET de los materiales anhidros, análisis térmico diferencial y termogravimétrico en pasta de cemento y mortero, resonancia magnética de silicio en pasta de cemento, difracción de rayos X de los materiales anhidros y de las probetas de pasta, microscopía electrónica de barrido con analizador de energía dispersiva por rayos X en pasta y mortero, y porosimetría por intrusión de mercurio en mortero. La caracterización macroscópica del material comprende ensayos de determinación del agua de consistencia normal y de los tiempos de inicio y fin de fraguado en pasta de cemento, ensayos de resistencia mecánica a flexión y compresión en probetas prismáticas de mortero, y ensayos de resistencia a compresión en probetas de hormigón. Para caracterizar la durabilidad se han desarrollado ensayos de determinación del coeficiente de migración de cloruros y ensayos de resistividad eléctrica en probetas de mortero. Todos los ensayos enumerados permiten clarificar el comportamiento de las cemesferas y compararlo con las distintas adiciones de uso convencional. Los resultados reflejan un buen comportamiento resistente y durable de los materiales con adición de cemesferas. La caracterización microscópica refleja su relación con las propiedades mesoscópicas y permite comprender mejor la evolución en los procesos de hidratación de las cemesferas. In recent years industrialised societies have become increasingly aware of the problem posed by indiscriminate emission of greenhouse gases into the atmosphere. Concrete, with a main component being cement, is arguably the most widely used construction material. At present, global emissions of CO2 due to the combustion of CaCO3 from Portland cement represent between 5% and 10% of the total. If the requirement of the Kyoto Protocol of a reduction of 5% of the total gas produced before 2020 is considered, then such values are of significant interest. The main objective of this work is the assessment of the microstructure and the hydration processes of cements with additions. Such an examination proposes research into new cementitious products based on vitreous spherical microparticles that may be added to the cement before the mixing process. The results are compared with the most commonly used conventional additions. The new material bases its composition on the chemistry of aluminium and silicates. By decreasing the amount of CaCO3, it is possible both to contribute to sustainable development and reduce CO2 emissions. The patent created by Grupo Cementos Portland Valderrivas (GCPV) describes the production process of microspheres (WO 2009/007470, 2010). The products that form the raw material for manufacture are clays, lime-stone, marl and industrial products or by-products that melt after being ground and fed into a gaseous fluid at high temperatures (1250°C and 1600°C). This process allows the obtaining of a product with a solid-spherical or micro-spherical shape and which, after being stabilised in a solid state by rapid cooling, obtains a high vitrification suitable for chemical reactivity, having a minimal surface in relation to its mass. Given that the final product has the fineness required, it prevents grinding that reduces CO2 emissions by saving fuel during this process. The process, which allows a wide range of cementitious materials to be obtained, not only addresses the problems caused by CO2 emissions but also enhances the availability of materials in countries that until the time of writing have not produced cement due to a lack of limestone. In addition, the calculation of the degree of hydration from the test results of DTA-TG is optimised and based on Bhatty and Pane calculation models. The proposed method allows prediction of the performance of the material from numerical interpolation of the amount of chemically bound water. The degree of hydration has a direct relationship with the development of material mechanical strength. In order to characterise the cement-based materials, an extensive experimental campaign in cement paste, concrete and mortar is conducted. The research comprises three levels: micro-structural characterisation, macro-structural and long-term behaviour (mainly durability). In total, eight additions are assessed: four conventional additions and four types of microspheres with different chemical compositions. The micro-scale tests include characterisation of chemical composition, particle size distribution and the BET specific surface area of anhydrous material, differential thermal and thermogravimetric analysis in cement paste and mortar, silicon-29 nuclear magnetic resonance in cement paste, X-ray diffraction of the anhydrous materials and paste specimens, scanning of electron microscopy with energy dispersive X-ray analyser in cement paste and mortar, and mercury intrusion porosimetry in mortar. The macroscopic material characterisation entails determination of water demand for normal consistency, and initial and final setting times of cement paste, flexural and compressive mechanical strength tests in prismatic mortar specimens, and compressive strength tests in concrete specimens. Tests for determining the chloride migration coefficient are performed to characterise durability, together with electrical resistivity tests in mortar specimens. All the tests listed allow clarification of the behaviour of the microspheres and comparison with the various additions of conventional use. The results show good resistance and durable behaviour of materials with a microsphere addition. Microscopic characterisation reflects their relationship with mesoscopic properties and provides insights into the hydration processes of the microspheres.

Estudio de la utilización de las cenizas de cenicero de centrales termoeléctricas de carbón como adición del cemento portland : análisis comparativo con las cenizas volantes

El empleo de nuevas adiciones en el cemento se plantea como una vía para que éste sea un material más sostenible. En este contexto, las cenizas de fondo o cenicero de las centrales termoeléctricas de carbón actualmente se están llevando a vertederos creando un problema medioambiental o se están empleando con usos minoritarios. Sin embargo, la presente Tesis doctoral demuestra cómo este material puede ser empleado como un componente principal de los cementos portland mezclado en una proporción optimizada con las cenizas volantes o solo. Por tanto, este estudio se puede considerar como un trabajo prenormativo que cubre las demandas de la sociedad tanto económicas como ambientales. Se han estudiado las propiedades químicas, físicas y mecánicas de las cenizas de fondo o cenicero de las centrales termoeléctricas de carbón como una adición potencial de los cementos portland (con adiciones) en comparación con los cementos portland con cenizas volantes. En consecuencia, el objeto de la presente Tesis Doctoral es el análisis de las prestaciones de morteros elaborados con clínkeres de cemento portland y cenizas de fondo o cenicero con cenizas volantes de las centrales termoeléctricas de carbón en unos porcentajes similares a los correspondientes a los CEM II/A-V, CEM II/B-V y CEM IV/A (V) de la UNE-EN 197-1:2011. La caracterización de las cenizas de fondo o cenicero y de las cenizas volantes de las centrales termoeléctricas de carbón se ha realizado mediante las técnicas analíticas de FRX, ICP, análisis químicos, DRX, densidad, granulometría láser, superficie específica Blaine, ATD, TG, puzolanicidad, MEB y EDX; mientras que la caracterización de las mezclas se ha realizado mediante análisis químico (análisis químico, FRX e ICP y), DRX, MIP, granulometría láser, puzolanicidad, MEB y EDX, agua de consistencia normal, inicio y final de fraguado, estabilidad de volumen, colorimetría, calor de hidratación, DTA y TG, asícomo ensayos de resistencia; resistencia a flexión y compresión y ensayos de durabilidad (carbonatación natural, resistencia al hielo-deshielo, resistencia a la acción de los sulfatos y resistencia a la reacción árido-álcali). Finalmente, se han comprobado las propiedades de las cenizas de cenicero y cenizas volantes en hormigones, realizando ensayos de resistencia a compresión y resistividad. Los resultados obtenidos indican que la sustitución parcial o completa de las cenizas volantes por las de cenicero no tiene un efecto tecnológicamente importante en las propiedades ni mecánicas ni durables, incluso los mejora en determinados aspectos. Por tanto, se recomienda la normalización de las cenizas de fondo o cenicero de las centrales termoeléctricas de carbón como componente principal de los cementos portland comunes de la UNE-EN 197-1:2011. Actualmente, la mayoría de las cenizas de fondo se consideran como un residuo que no tiene un posible uso. Sólo se han encontrado algunos datos relativos a la aplicación de este material combinado con cenizas volantes como un componente principal de los cementos portland. Por tanto, la realización de un estudio integrado considerando aspectos que van desde la caracterización de las cenizas hasta las mezclas de conglomerante y la hidratación de éstas, desarrollo de resistencias y demás prestaciones y durabilidad (carbonatación natural, resistencia al hielo-deshielo, resistencia a la acción de los sulfatos y resistencia a la reacción árido-álcali), así como los ensayos de resistencia en hormigón es totalmente novedoso. Como resultado final se propone incorporar estas nuevas adiciones en aplicaciones particulares y en la norma más apropiada para ello. Los resultados han demostrado que la sustitución completa o parcial de las cenizas volantes por cenizas de fondo o cenicero de las centrales termoeléctricas de carbón en cementos de los tipos CEM II/A-V, CEM II/B-V y CEM IV/A no afecta de forma significativa en la resistencia a compresión a 1, 3 ,7, 28 ni 90 días ni a la durabilidad. En parte esto se debe a que la composición química de ambas cenizas es muy similar en la mayoría de los elementos tales como Fe2O3, TiO2, P2O5, SrO2, aunque en algún caso, como en el ZnO, se encuentra alguna ligera diferencia. Por tanto, se pueden esperar unas ligeras diferencias en el mecanismo de hidratación de las diferentes mezclas estudiadas. La presencia de los óxidos mencionados afectará a la composición de la fase acuosa y, en consecuencia, podrían ser elementos lixiviables. Asimismo, influyen de distinta manera en propiedades tales como los tiempos de fraguado y en la durabilidad. New additions to the cement are needed to achieve a more sustainable construction material. Within this context, bottom ashes produced in coal-fired power stations are currently wastes which are dumped provoking an environmental problem. Only in few cases are being used in minor applications. However, the present PhD Thesis shows how this material can be used as a main constituent of Portland cement when it is mixed in an optimised proportion with fly ashes or added to the Portland clinker alone. Therefore, this study may also be considered as a pre-standardization work which covers both the environmental and economic demands of society. Chemical, physical and mechanical characteristics of pulverized coal combustion bottom ash used as a potential constituent of Portland cements (with additions) are studied in comparison to Portland cements with fly ashes. Therefore, the aim of this experimental PhD Thesis is the analysis of the performance of mortars made of clinker of Portland cement and bottom and/or fly ashes in similar proportions to those of CEM II/A-V, CEM II/B-V and CEM IV/A (V) according to EN 197-1:2011. Characterisation of bottom and fly ashes has been done by XRF, ICP, chemical analyses, XRD, density, laser granulometry, Blaine, ATD, TG, pozzolanity, SEM and EDS. Characterisation of bottom and fly ashes mixes has been perform by chemical analyses, XRF, ICP, XRD, MIP, laser granulometry, pozzolanity, SEM, EDS, setting time, soundness, colorimetric test, heat of hydration, ATD, TG, compressive strength, and durability tests (natural carbonation, frost-thaw resistance, sulphate resistance and silica-alkali resistance). In conclusion, it can be established that partial or complete replacement of fly ash by bottom ash has neither significant effect on mechanical nor durability properties. Even, they are improved in several aspects. Therefore, it is recommended to standardise the bottom ash as a main cement constituent of the European standard EN 197-1:2011. Nowadays, most bottom ashes are considered as waste without any potential re-use. Only a few papers deal with the study of this material and its use mixed with fly ashes to be employed as a main constituent of Portland cement. Therefore, the execution of an integrated study considering together aspects from the initial characterization of the ashes and blinder mixes to the hydration steps, strength achievement, leading behaviour and durability (natural carbonation, sulphate attack, aggregate-alcali reaction and freeze-thaw resistance) is totally new. As result, it is proposed to include this new addition for particular applications in the appropriate cement standard. The results have shown that with regard to the compressive strength at 1, 3, 7, 28 and 90 days, partial or complete replacement of fly ash by bottom ash in CEM II/A-V, CEM II/B-V and CEM IV/A has no more significant effects. Partially, this can be explained because the bottom ash contains a similar amount of most of the elements, Fe2O3, TiO2, P2O5, SrO2, and so on, instead of ZnO. Therefore, slight hydration differences are expected. The presence of such oxides might have a significant effect on pore solution concentration and so will be leachable constituents. They will also play an important role in the cement properties such as setting times and durability.

Capacidad y comportamiento de la adsorción de fenol en caolines naturales y modificados

En la actualidad las industrias químicas, farmacéuticas y clínicas, originan contaminantes en aguas superficiales, aguas subterráneas y suelos de nuestro país, como es el caso del fenol, contaminante orgánico común y altamente dañino para los organismos, incluso a bajas concentraciones. Existen en el mercado diferentes metodologías para minimizar la contaminación pero muchos de estos procesos tienen un alto coste, generación de contaminantes, etc. La adsorción de contaminantes por medio de arcillas es un método ampliamente utilizado, encontrándose eficaz y económico. Pero la dificultad de adsorber un contaminante orgánico como el fenol motiva la creación de un material llamado organoarcillas. Las organoarcillas son arcillas modificadas con un surfactante, a su vez, los surfactantes son moléculas orgánicas que confieren a la superficie de la arcilla carga catiónica en lugar de aniónica, haciendo más fácil la adsorción de fenol. Para esta tesis se ha elegido el caolín como material adsorbente, fácilmente disponible y relativamente de bajo coste. Se ha trabajado con: arenas de caolín, material directo de la extracción, y caolín lavado, originado del proceso de lavado de las arenas de caolín. Ambos grupos se diferencian fundamentalmente por su contenido en cuarzo, ampliamente mayor en las arenas de caolín. Con el objetivo de desarrollar un material a partir del caolín y arenas de éste con capacidad de retención de contaminates, en concreto, fenol, se procedió a modificar los materiales de partida mediante tratamientos térmicos, mecánicos y/o químicos, dando lugar a compuestos con mayor superficie química reactiva. Para ello se sometió el caolín y las arenas caoliníferas a temperaturas de 750ºC durante 3h, a moliendas hasta alcanzar su amorfización, y/o a activaciones con HCl 6M o con NaOH 5M durante 3h a 90ºC. En total se obtuvieron 18 muestras, en las que se estudiaron las características físico-químicas, mineralógicas y morfológicas de cada una de ellas con el fin de caracterizarlas después de haber sufrido los tratamientos y/o activaciones químicas. Los cambios producidos fueron estudiados mediante pH, capacidad de intercambio catiónico (CEC), capacidad de adsorción de agua (WCU y CWC), distribución de tamaño de partícula (PSD), área de superficie específica (SBET), difracción de rayos X (XRD), espectroscopía infrarroja por transformada de Fourier (FTIR), métodos térmicos (TG, DTG y DTA), y microscopía electrónica de transmisión y barrido (SEM y TEM). Además se analizó los cambios producidos por los tratamientos en función de las pérdidas de Al y Si que acontece en las 18 muestras. Los resultados para los materiales derivados de la arenas caoliníferas fueron similares a los obtenidos para los caolines lavados, la diferencia radica en la cantidad de contenido de caolinita en los diferente grupos de muestras. Apoyándonos en las técnicas de caracterización se puede observar que los tratamientos térmico y molienda produce materiales amorfos, este cambio en la estructura inicial sumado a las activaciones ácida y alcalina dan lugar a pérdidas de Si y Al, ocasionando que sus propiedades físico-químicas, mineralógicas y morfológicas se vean alteradas. Un fuerte aumento es observado en las áreas superficiales y en la CEC en determinadas muestras, además entre los cambios producidos se encuentra la producción de diferentes zeolitas en porcentajes distintos con el tratamiento alcalino. Para la obtención de las organoarcillas, las 18 muestras se sometieron a la surfactación con hexadeciltrimetil amonio (HDTMA) 20 mM durante 24h a 60ºC, esta concentración de tensioactivo fue más alta que la CEC de cada muestra. Los camext bios anteriormente producidos por los tratamientos y activaciones, afectan de forma diferente en la adsorción de HDTMA, variando por tanto la adsorción del surfactante en la superficie de las muestras. Se determinó el tensioactivo en superficie por FTIR, además se realizó un análisis de componentes principales (PCA) para examinar la dependencia entre las relaciones Si/Al de las muestras en la capacidad de adsorción de tensioactivo, y para el estudio de la adsorción de HDTMA en las muestras se realizaron además del análisis termogravimétrico, aproximaciones con los modelos de Freundllich y Langmuir. Se persigue conocer las diferentes formas y maneras que tiene el tensioactivo de fijarse en la superficie de las muestras. En las organoarcillas resultantes se cuantificó el fenol adsorbido cuando éstas fueron puestas en contacto con diferentes concentraciones de fenol: 50, 500, 1000, 2000, y 2500 mg/l durante 24h. El contaminante sorbido se calculó por medio de cromatografía de gases, y se realizaron aproximaciones con los modelos de Freundllich y Langmuir. El comportamiento de adsorción de fenol en arcillas orgánicas es regido por las características de las muestras. De forma general se puede decir que las muestras de caolines lavados tienen más capacidad de adsorción de fenol que las muestras de arenas de caolín y que la activación alcalina ha proporcionado una mejora en la adsorción de fenol en los dos grupos. En consecuencia se han obtenido materiales adsorbentes heterogéneos y por tanto, con propiedades diferentes. Se ha evaluado el comportamiento global de las arenas de caolín por un lado y del caolín lavado por otro. Las arenas de caolín presentan altos niveles de cuarzo y su uso para ciertos tipos de industrias no son recomendados en ocasiones por el alto costo que el proceso de limpieza y purificación implicaría. Por ello es importante reseñar en este proyecto las aplicaciones que ofrecen algunas muestras de este grupo. Los ensayos acontecidos en esta tesis han dado lugar a las siguientes publicaciones: • Pérdida de Al y Si en caolines modificados térmica- o mecánicamente y activados por tratamientos químicos. A. G. San Cristóbal, C Vizcayno, R. Castelló. Macla 9, 113-114. (2008). • Acid activation of mechanically and thermally modfied kaolins. A. G. San Cristóbal, R. Castelló, M. A. Martín Luengo, C Vizcayno. Mater. Res. Bull. 44 (2009) 2103-2111. • Zeolites prepared from calcined and mechanically modified kaolins. A comparative study. A. G San Cristóbal, R. Castelló, M. A. Martín Luengo, C Vizcayno. Applied Clay Science 49 (2010) 239-246. • Study comparative of the sorption of HDTMA on natural and modified kaolin. A. G San Cristóbal, R. Castelló, J. M. Castillejo, C Vizcayno. Aceptada en Clays and Clay minerals. • Capacity of modified kaolin sand and washed kaolin to adsorb phenol. A. G San Cristóbal, R. Castelló, C Vizcayno. Envío a revista sujeto a la publicación del artículo anterior. ABSTRACT Today’s chemical, pharmaceutical and clinical industries generate pollutants that affect the soils and surface and ground waters of our country. Among these, phenol is a common organic pollutant that is extremely harmful to living organisms, even at low concentrations. Several protocols exist to minimize the effects of pollutants, but most are costly procedures or even generate other pollutants. The adsorption of hazardous materials onto clays is perhaps the most used, efficient and cost-saving method available. However, organic compounds such as phenol are difficult to adsorb and this has led to the development of materials known as organoclays, which are much better at remediating organic compounds. Organoclays are clays that have been modified using a surfactant. In turn, surfactants are organic molecules that confer a cationic rather than anionic charge to the clay surface, improving it’s capacity to adsorb phenol. For this doctorate project, kaolin was selected as an adsorbent material for the removal of phenol given its easy sourcing and relatively low cost. The materials investigated were kaolin sand, a directly extracted material, and washed kaolin, which is the byproduct of the kaolin sand washing process. The main difference between the materials is their quartz content, which is much higher in the kaolin sands. To generate a product from kaolin or kaolin sand capable of retaining organic pollutants such as phenol, both materials were subjected to several heat, chemical and/or mechanical treatments to give rise to compounds with a greater reactive surface area. To this end the two starting materials underwent heating at 750ºC for 3 h, grinding to the point of amorphization and/or activation with HCl 6M or NaOH 5M for 3 h at 90ºC. These treatments gave rise to 18 processed samples, which were characterized in terms of their morphological, mineralogical, and physical-chemical properties. The behaviour of these new materials was examined in terms of their pH, cation exchange capacity (CEC), water adsorption capacity (WCU and WCC), particle size distribution (PSD), specific surface area (SBET), and their X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), thermal (DTG, DTA) and scanning and transmission electron microscopy (SEM and TEM) properties. The changes conferred by the different treatments were also examined in terms of Al and Si losses. Results for the materials derived from kaolin sands and washed kaolin were similar, with differences attributable to the kaolinite contents of the samples. The treatments heat and grinding produced amorphous materials, which when subjected to acid or alkali activation gave rise to Si and Al losses. This in turn led to a change in physico- chemical, mineralogical and morphological properties. Some samples showed a highly increased surface area and CEC. Further, among the changes produced, alkali treatment led to the generation of zeolites in different proportions depending on the sample. To produce the organoclays, the 18 samples were surfacted with hexadecyltrimethylammonium (HDTMA) 20 mM for 24 h at 60ºC. This surfactant concentration is higher than the CEC of each sample. The amount of HDTMA adsorbed onto the surface of each sample determined by FTIR varied according to treatment. A principle components analysis (PCA) was performed to examine correlations between sample Si/Al ratios and surfactant adsorption capacity. In addition, to explore HDTMA adsorption by the samples, DTG and DTA data were fitted to Freundllich and Langmuir models. The mechanisms of surfactant attachment to the sample surface were also addressed. The amount of phenol adsorbed by the resultant organoclays was determined when exposed to different phenol concentrations: 50, 500, 1000, 2000, and 2500 mg/l for 24 h. The quantity of adsorbed pollutant was estimated by gas chromatography and the data fitted to the models of Freundllich and Langmuir. Results indicate that the phenol adsorption capacity of the surfacted samples is dependent on the sample’s characteristics. In general, the washed kaolin samples showed a greater phenol adsorption capacity than the kaolon sands and alkali activation improved this capacity in the two types of sample. In conclusion, the treatments used gave rise to adsorbent materials with varying properties. Kaolin sands showed high quartz levels and their use in some industries is not recommended due to the costs involved in their washing and purification. The applications suggested by the data obtained for some of the kaolin sand samples indicate the added value of this industrial by-product. The results of this research project have led to the following publications: • Pérdida de Al y Si en caolines modificados térmica- o mecánicamente y activados por tratamientos químicos. A. G. San Cristóbal, C Vizcayno, R. Castelló. Macla 9, 113-114. (2008). • Acid activation of mechanically and thermally modfied kaolins. A. G. San Cristóbal, R. Castelló, M. A. Martín Luengo, C Vizcayno. Mater. Res. Bull. 44 (2009) 2103-2111. • Zeolites prepared from calcined and mechanically modified kaolins. A comparative study. A. G. San Cristóbal, R. Castelló, M. A. Martín Luengo, C Vizcayno. Applied Clay Science 49 (2010) 239-246. • Study comparative of the sorption of HDTMA on natural and modified kaolin. A. G. San Cristóbal, R. Castelló, J. M. Castillejo, C Vizcayno Accepted in Clays and Clay minerals. • Capacity of modified kaolin sand and washed kaolin to adsorb phenol. A. G San Cristóbal, R. Castelló, C Vizcayno. Shipment postponed, subject to the publication of the previous article.

Fused polycationic peptide mediates delivery of diphtheria toxin A chain to the cytosol in the presence of anthrax protective antigen.

The lethal factor (LF) and edema factor (EF) of anthrax toxin bind by means of their amino-terminal domains to protective antigen (PA) on the surface of toxin-sensitive cells and are translocated to the cytosol, where they act on intracellular targets. Genetically fusing the amino-terminal domain of LF (LFN; residues 1-255) to certain heterologous proteins has been shown to potentiate these proteins for PA-dependent delivery to the cytosol. We report here that short tracts of lysine, arginine, or histidine residues can also potentiate a protein for such PA-dependent delivery. Fusion of these polycationic tracts to the amino terminus of the enzymic A chain of diphtheria toxin (DTA; residues 1-193) enabled it to be translocated to the cytosol by PA and inhibit protein synthesis. The efficiency of translocation was dependent on tract length: (LFN > Lys8 > Lys6 > Lys3). Lys6 was approximately 100-fold more active than Arg6 or His6, whereas Glu6 and (SerSerGly)2 were inactive. Arg6DTA was partially degraded in cell culture, which may explain its low activity relative to that of Lys6DTA. The polycationic tracts may bind to anionic sites at the cell surface (possibly on PA), allowing the fusion proteins to be coendocytosed with PA and delivered to the endosome, where translocation to the cytosol occurs. Excess free LFN blocked the action of LFNDTA, but not of Lys6DTA. This implies that binding to the LF/EF site is not an obligatory step in translocation and suggests that the polycationic tag binds to a different site. Besides elucidating the process of translocation in anthrax toxin, these findings may aid in developing systems to deliver heterologous proteins and peptides to the cytoplasm of mammalian cells.

Transgenic mice carrying the diphtheria toxin A chain gene under the control of the granzyme A promoter: expected depletion of cytotoxic cells and unexpected depletion of CD8 T cells.

We have generated transgenic mice bearing the diphtheria toxin A chain (DTA) gene under the control of granzyme A (GrA) promoter sequences (GrA-DTA). GrA is expressed in activated cytotoxic cells but not in their immediate progenitors. These GrA-DTA mice are deficient in cytotoxic functions, indicating that most cytotoxic cells express GrA in vivo. Surprisingly, one founder strain containing a multicopy GrA-DTA insert show a marked and selective deficiency in CD8+ cells in peripheral lymphoid organs. This depletion was not observed in thymus, where the distribution of CD4+ and CD8+ cells is normal. Moreover, the emigration of T cells from thymus is normal, indicating that the depletion occurs in the periphery. GrA-DTA mice should be useful as models to dissect the role of cytotoxic cells in immune responses and as recipients of normal and neoplastic hematopoietic cells. The selective depletion of CD8+ cells in one founder strain could have implications for postthymic T-cell development.

Complexos de dirutênio com os fármacos ibuprofeno, ácido acetilsalicílico, naproxeno, indometacina, e com ácido y-linolêncio: Síntese, caracterização, avaliação da ação antiproliferativa sobre células tumorais e estudo da interação da unidade dimetálica com adenina e adenosina

Este trabalho tem como principal objetivo contribuir para o desenvolvimento de novos potenciais metalofármacos de rutênio. Nele são descritas a síntese, a caracterização e a avaliação da ação antiproliferativa de alguns complexos de dirutênio (II,III) com os fármacos antiinflamatórios não-esteróides (AINEs): ibuprofeno (ibp), ácido acetilsalicílico (aas), naproxeno (npx) e indometacina (ind) e também com o ácido γ-linolênico (lin), sobre células cancerígenas. Os compostos obtidos foram caracterizados por análise elementar, espectroscopia de absorção eletrônica, medidas de susceptibilidade magnética, espectroscopia vibracional FTIR e Raman, difratometria de raios X de pó, medidas de condutividade molar e análise térmica (TG, OTAe OSC). Todos os complexos sintetizados apresentam estrutura em gaiola, com os carboxilatos derivados dos fármacos AINEs coordenados à unidade dimetálica Ru2( (II,III), em ponte equatorial, estabilizando assim a ligação direta rutênio-rutênio. As posições axiais são ocupadas por íons cloreto, no caso dos complexos [Ru2(O2(CR)4(Cl] (O2(CR = ibp, aas, npx ou ind), ou por moléculas de água, nas espécies do tipo [Ru2(O2(CR)4(H2O)2]PF6(O2CR =npx e ind). Ensaios biológicos demonstraram que os compostos [Ru2(ibp) 4Cl]•½H2O e [Ru2(npx)4(H2O)2]PF6 apresentam ação antiproliferativa sobre células de glioma de rato C6 in vitro, dependendo do tempo de exposição do meio celular ao complexo. O complexo [Ru2 (lin)4Cl] também apresenta efeito sobre a proliferação de células C6; entretanto, nesse caso, efeitos significativos são observaçlos já nas primeiras 24 h de exposição. Estudos mostraram que as bases adenina e adenosina reagem com o complexo [Ru2(OAc)4(H2O)2]PF6 sem que ocorra quebra da estrutura em gaiola. As bases nitrogenadas substituem axialmente as moléculas de água, formando pontes axiais entre duas unidades de dirutênio (II,III) no estado sólido.

O sistema PBL, problem-based learning, no ensino de medicina no Brasil : análise bibliográfica sobre a sua execução

Introdução: Entre as estratégias de ensino e aprendizagem utilizadas nas práticas pedagógicas, a Problem Based Learning (PBL) (Aprendizagem Baseada em Problemas) é utilizada desde 1960, em especial nos cursos de Medicina. Mesmo sendo uma estratégia valiosa, um dos seus obstáculos é a pouca prática dos alunos em atividades autodirigidas, pesquisa e construção coletiva do conhecimento. Objetivo: Rastrear elementos constitutivos da PBL através de dados colhidos em artigos pesquisados em sítios de divulgação científica; Avaliar, nos estudos selecionados, os aspectos positivos e negativos que estejam relacionados com a metodologia do Sistema PBL aplicada ao ensino médico no Brasil. Metodologia: Estudo bibliográfico de 13 textos utilizando um modelo de desconstrução, denominada Análise Textual Discursiva (ATD) que consiste em: transformação dos artigos em pedaços menores; análise textual; identificação de padrões convergentes e divergentes em relação a PBL; organização e síntese dos dados, culminando com a elaboração de estratégia adaptativa da PBL para o curso de Medicina. Resultados: Foram encontradas 116 citações que convergiam para referências positivos acerca da metodologia PBL e 40 citações que divergiam acerca dos pontos positivos. Os aspectos positivos como o desenvolvimento de atitudes e habilidades; desenvolvimento de competências anteriores ao curso; efeitos positivos depois de terminada a graduação, como autonomia de estudo e a articulação entre currículo e realidade profissional, representam pontos a serem reforçados na aula. Em contraponto, foi observado que dentre os negativos a não compreensão do papel do professor como tutor; necessidade de conteúdo formal tradicional pelos alunos e a expectativa que o professor retire as suas dúvidas são pontos a serem evitados. Conclusões: A metodologia PBL deverá servir como metodologia ativa para aproveitar ao máximo as habilidades que os alunos já apresentam, potencializando o aprendizado na educação médica em sala de aula. Palavras-Chave: PBL; curso de medicina; metodologia ativa; educação médica.

Project risk management:a combined analytic hierarchy process and decision tree approach

Time, cost and quality achievements on large-scale construction projects are uncertain because of technological constraints, involvement of many stakeholders, long durations, large capital requirements and improper scope definitions. Projects that are exposed to such an uncertain environment can effectively be managed with the application of risk management throughout the project life cycle. Risk is by nature subjective. However, managing risk subjectively poses the danger of non-achievement of project goals. Moreover, risk analysis of the overall project also poses the danger of developing inappropriate responses. This article demonstrates a quantitative approach to construction risk management through an analytic hierarchy process (AHP) and decision tree analysis. The entire project is classified to form a few work packages. With the involvement of project stakeholders, risky work packages are identified. As all the risk factors are identified, their effects are quantified by determining probability (using AHP) and severity (guess estimate). Various alternative responses are generated, listing the cost implications of mitigating the quantified risks. The expected monetary values are derived for each alternative in a decision tree framework and subsequent probability analysis helps to make the right decision in managing risks. In this article, the entire methodology is explained by using a case application of a cross-country petroleum pipeline project in India. The case study demonstrates the project management effectiveness of using AHP and DTA.

Use of colour image analysis for assessment of fire damaged concrete

The aim of this project was to carry out a fundamental study to assess the potential of colour image analysis for use in investigations of fire damaged concrete. This involved:(a) Quantification (rather than purely visual assessment) of colour change as an indicator of the thermal history of concrete.(b) Quantification of the nature and intensity of crack development as an indication of the thermal history of concrete, supporting and in addition to, colour change observations.(c) Further understanding of changes in the physical and chemical properties of aggregate and mortar matrix after heating.(d) An indication of the relationship between cracking and non-destructive methods of testing e.g. UPV or Schmidt hammer. Results showed that colour image analysis could be used to quantify the colour changes found when concrete is heated. Development of red colour coincided with significant reduction in compressive strength. Such measurements may be used to determine the thermal history of concrete by providing information regarding the temperature distribution that existed at the height of a fire. The actual colours observed depended on the types of cement and aggregate that were used to make the concrete. With some aggregates it may be more appropriate to only analyse the mortar matrix. Petrographic techniques may also be used to determine the nature and density of cracks developing at elevated temperatures and values of crack density correlate well with measurements of residual compressive strength. Small differences in crack density were observed with different cements and aggregates, although good correlations were always found with the residual compressive strength. Taken together these two techniques can provide further useful information for the evaluation of fire damaged concrete. This is especially so since petrographic analysis can also provide information on the quality of the original concrete such as cement content and water / cement ratio. Concretes made with blended cements tended to produce small differences in physical and chemical properties compared to those made with unblended cements. There is some evidence to suggest that a coarsening of pore structure in blended cements may lead to onset of cracking at lower temperatures. The use of DTA/TGA was of little use in assessing the thermal history of concrete made with blended cements. Corner spalling and sloughing off, as observed in columns, was effectively reproduced in tests on small scale specimens and the crack distributions measured. Relationships between compressive strength/cracking and non-destructive methods of testing are discussed and an outline procedure for site investigations of fire damaged concrete is described.

Melting and solidification of Zinc-Aluminium alloys

Following a scene-setting introduction are detailed reviews of the relevant scientific principles, thermal analysis as a research tool and the development of the zinc-aluminium family of alloys. A recently introduced simultaneous thermal analyser, the STA 1500, its use for differential thermal analysis (DTA) being central to the investigation, is described, together with the sources of support information, chemical analysis, scanning electron microscopy, ingot cooling curves and fluidity spiral castings. The compositions of alloys tested were from the binary zinc-aluminium system, the ternary zinc-aluminium-silicon system at 30%, 50% and 70% aluminium levels, binary and ternary alloys with additions of copper and magnesium to simulate commercial alloys and five widely used commercial alloys. Each alloy was shotted to provide the smaller, 100mg, representative sample required for DTA. The STA 1500 was characterised and calibrated with commercially pure zinc, and an experimental procedure established for the determination of DTA heating curves at 10°C per minute and cooling curves at 2°C per minute. Phase change temperatures were taken from DTA traces, most importantly, liquidus from a cooling curve and solidus from both heating and cooling curves. The accepted zinc-aluminium binary phase diagram was endorsed with the added detail that the eutectic is at 5.2% aluminium rather than 5.0%. The ternary eutectic trough was found to run through the points, 70% Al, 7.1% Si, 545°C; 50% Al, 3.9% Si, 520°C; 30% Al, 1.4% Si, 482°C. The dendrite arm spacing in samples after DTA increased with increasing aluminium content from 130m at 30% to 220m at 70%. The smallest dendrite arm spacing of 60m was in the 30% aluminium 2% silicon alloy. A 1kg ingot of the 10% aluminium binary alloy, insulated with Kaowool, solidified at the same 2°C per minute rate as the DTA samples. A similar sized sand casting was solidified at 3°C per minute and a chill casting at 27°C per minute. During metallographic examination the following features were observed: heavily cored phase which decomposed into ' and '' on cooling; needles of the intermetallic phase FeAl4; copper containing ternary eutectic and copper rich T phase.

The durability of glass fibre reinforced cements made with new cementitious matrices

Widespread use of glass fibre reinforced cement (GRC) has been impeded by concerns over its durability. Three degradation mechanisms are proposed - fibre corrosion, Ca(OHh precipitation and matrix densification - although their relative importance is debated. Matrices with reduced alkalinities and Ca(OH)2 contents are being developed; the aim of this study was to investigate their hydration and interaction with alkali-resistant fibres to determine the factors controlling their long-term durability, and assess the relevancy of accelerated ageing. The matrices studied were: OPC/calcium-sulphoaluminate cement plus metakaolin (C); OPC plus metakaolin (M); blast-furnace slag cement plus a micro-silica based additive (D); and OPC (O). Accelerated ageing included hot water and cyclic regimes prior to tensile testing. Investigations included pore solution expression, XRD, DTA/TG, SEM and optical petrography. Bond strength was determined from crack spacings using microstructural parameters obtained from a unique image analysis technique. It was found that, for the new matrices - pore solution alkalinities were lower; Ca(OH)2 was absent or quickly consumed; different hydrates were formed at higher immersion temperatures; degradation under 65°C immersion was an order of magnitude slower, and no interfilamental Ca(OH)2 was observed .It was concluded that: fibre weakening caused by flaw growth was the primary degradation mechanism and was successfully modelled on stress corrosion/static fatigue principles. OPC inferiority was attributed partly to its higher alkalinity but chiefly to the growth of Ca(OH)2 aggravating the degradation; and hot water ageing although useful in model formulation and contrasting the matrices, changed the intrinsic nature of the composites rather than simply accelerating the degradation mechanisms.