SnO(2)-based materials for pesticide degradation

This study presents the results of the degradation of the pesticide atrazine using electrochemical and photo-assisted electrochemical degradation techniques using SnO(2)-containing electrode of nominal composition electrodes of composition Ti/Ru(x)Sni-(x)O(2) (where X = 0.10, 0.15, 0.20, 0.25 and 0.30). The materials were characterized ex situ and in situ in order to correlate the observed atrazine removal rates with electrode morphology/composition. The results obtained demonstrate the effectiveness of the photo-assisted electrochemical degradation. Using purely electrochemical methods the rate of atrazine removal is almost zero at all the electrodes studied. However, the application of photo-assisted degradation results in almost complete atrazine removal in 1 h of electrolysis. The efficiency of atrazine degradation does not seem to be greatly affected by the electrode material or by SnO(2) content, but the overall COD removal is dependent on the SnO(2) content. Overall, the SnO(2)-containing electrodes do not reach the level of COD removal (maximum similar to 21%) seen for the Ti/Ru(0.3)Ti(0.2)O(2) electrode. An interesting correlation between the morphology factor (phi) and chemical oxygen demand removal is observed. (C) 2010 Elsevier B.V. All rights reserved.

Anodic oxidation of wastewater containing the Reactive Orange 16 Dye using heavily boron-doped diamond electrodes

Boron-doped diamond (BDD) films grown on the titanium substrate were used to study the electrochemical degradation of Reactive Orange (RO) 16 Dye. The films were produced by hot filament chemical vapor deposition (HFCVD) technique using two different boron concentrations. The growth parameters were controlled to obtain heavily doped diamond films. They were named as E1 and E2 electrodes, with acceptor concentrations of 4.0 and 8.0 x 10(21) atoms cm(-3), respectively. The boron levels were evaluated from Mott-Schottky plots also corroborated by Raman`s spectra, which characterized the film quality as well as its physical property. Scanning Electron Microscopy showed well-defined microcrystalline grain morphologies with crystal orientation mixtures of (1 1 1) and (1 00). The electrode efficiencies were studied from the advanced oxidation process (AOP) to degrade electrochemically the Reactive Orange 16 azo-dye (RO16). The results were analyzed by UV/VIS spectroscopy, total organic carbon (TOC) and high-performance liquid chromatography (HPLC) techniques. From UV/VIS spectra the highest doped electrode (E2) showed the best efficiency for both, the aromaticity reduction and the azo group fracture. These tendencies were confirmed by the TOC and chromatographic measurements. Besides, the results showed a direct relationship among the BDD morphology, physical property, and its performance during the degradation process. (C) 2011 Elsevier B.V. All rights reserved.

Photo-assisted electrochemical degradation of real textile wastewater

In the present study, photo-assisted electrochemical degradation of real textile wastewater was performed. Degradation assays were performed at constant current (40 mA cm(-2)) in a combined electro/photochemical flow-cell using a Ti/Ru(0.3)Ti(0.7)O(2) DSA(R) type electrode. The results show that the method is capable of removing color and chemical oxygen demand (COD) from the effluent. Additionally, the effect of initial pH and type of supporting electrolyte (Na(2)SO(4) or NaCl) was investigated. The principal figures of merit used in this study were COD removal and color removal (605 nm). The results show that up to 72% color and up to 59% COD removal in 120 min is possible under the operating conditions employed. Studies of the phytotoxicity of the wastewater before and after the photo-assisted degradation assays are also presented and the results demonstrate that the toxicity of the effluent is dependent on the length of electrolysis time and the treatment procedure employed.

Paper Microzone Plates

This paper describes 96- and 384-microzone plates fabricated in paper as alternatives to conventional multi-well plates fabricated in molded polymers. Paper-based plates are functionally related to plastic well plates, but they offer new capabilities. For example, paper-microzone plates are thin (similar to 180 mu m), require small volumes of sample (5 mu L per zone), and can be manufactured from inexpensive materials ($0.05 per plate). The paper-based plates are fabricated by patterning sheets of paper, using photolithography, into hydrophilic zones surrounded by hydrophobic polymeric barriers. This photolithography used an inexpensive formulation photoresist that allows rapid (similar to 15 min) prototyping of paper-based plates. These plates are compatible with conventional microplate readers for quantitative absorbance and fluorescence measurements. The limit of detection per zone loaded for fluorescence was 125 fmol for fluorescein isothiocyanate-labeled bovine serum albumin, and this level corresponds to 0.02 the quantity of analyte per well used to achieve comparable signal-to-noise in a 96-well plastic plate (using a solution of 25 nM labeled protein). The limits of detection for absorbance on paper was aproximately 50 pmol per zone for both Coomassie Brilliant Blue and Amaranth dyes; these values were 0.4 that required for the plastic plate. Demonstration of quantitative colorimetric correlations using a scanner or camera to image the zones and to measure the intensity of color, makes it possible to conduct assays without a microplate reader.

Comparison of the analytical performance of electrophoresis microchannels fabricated in PDMS, glass, and polyester-toner

This paper compares the analytical performance of microchannels fabricated in PDMS, glass, and polyester-toner for electrophoretic separations. Glass and PDMS chips were fabricated using well-established photolithographic and replica-molding procedures, respectively. PDMS channels were sealed against three different types of materials: native PDMS, plasma-oxidized PDMS, and glass. Polyester-toner chips were micromachined by a direct-printing process using an office laser printer. All microchannels were fabricated with similar dimensions according to the limitations of the direct-printing process (width/depth 150 mu m/12 mu m). LIF was employed for detection to rule out any losses in separation efficiency due to the detector configuration. Two fluorescent dyes, coumarin and fluorescein, were used as model analytes. Devices were evaluated for the following parameters related to electrophoretic separations: EOF, heat dissipation, injection reproducibility, separation efficiency, and adsorption to channel wall.

A Madeira e os alemães, 1917-1939: o discurso na imprensa madeirense

O presente estudo, subordinado à temática «Encontro entre Culturas» e «A Madeira e os Alemães», propõe-se à investigação da representatividade da intervenção alemã sobre o contexto regional, através da análise da visão madeirense sobre o povo e cultura germânicos. Desde recuados tempos o fenómeno «ilheidade» sempre esteve subjacente à sensação do «ser e estar madeirenses», o indagar pelo desconhecido do além-mar, a ânsia de transpor o horizonte fora do que a vista alcança, foram, com o passar dos tempos, sensações despertas pelo contacto com outras culturas. Com o romper do liberalismo arranca o jornalismo insular e, com ele, a manifestação do discurso público, numa dimensão até então desconhecida. Pela primeira vez na história madeirense, os madeirenses falam de si próprios, dando azo à auto e hetero-observação. A percepção do «outro» remeterá para uma reflexão sobre a visão endógena da identidade cultural madeirense e, simultaneamente, para a visão exógena da «diferença» do «outro», neste caso do «alemão». Neste estudo estarão constantemente perceptíveis os fenómenos da alteridade e da interculturalidade luso-germânica, assim como a rivalidade anglogermânica. Pela mesma altura começam a desenhar-se na ilha vínculos com a nação emergente, a Alemanha, quer no âmbito terapêutico-científico, demonstrado na questão da «Madeirasache» e da concessão dos sanatórios na ilha, quer no concernente ao interesse germânico pela ilha, segundo conveniências estratégico-militares ou político-turísticas. A conjuntura político-económica e social vigente durante o período 1917-1939 agudizará as relações luso-germânicas, o germanófilo Sidónio de Pais ascende ao poder, cessa a Grande Guerra, floresce o fascismo europeu. O dirigível alemão passa pela ilha, o turismo nazi elege a Madeira como regular destino turístico, a Juventude Hitleriana acampa na ilha, enquanto uma segunda guerra mundial está prestes a eclodir. A opinião pública fervilhará ao ritmo dos acontecimentos, manifestando-se na imprensa local posições pró e antigermânicas.

Encapsulation of single hMSCs in polyelectrolyte shells

The main objective of this Thesis was to encapsulate single viable cells within polyelectrolyte films using the Layer-by-Layer (LbL) technique. Most of the experiments used human mesenchymal stem cells (MSCs) whose characteristics (capacity of selfrenewal and potential to differentiate into several types of cells) make them particularly interesting to be used in biomedical applications. Also, most of the experiments used alginate (ALG) as the anionic polyelectrolyte and chitosan (CHI) or poly(allylamine hydrochloride) (PAH) as the cationic polyelectrolyte. Hyaluronic acid (HA) was also tested as an anionic polyelectrolyte. At the beginning of the work, the experimental conditions necessary to obtain the encapsulation of individual cells were studied and established. Through fluorescence microscopy visualization by staining the cell nucleus and using polyelectrolytes conjugated to fluorescent dyes, it was possible to prove the obtainment of capsules containing one single cell inside. Capsules aggregation was an observed problem which, despite the efforts to design an experimental process to avoid this situation (namely, by playing with cell concentration and different means of re-suspending and stirring the cells), was not completely overcome. In a second part of the project, single cells were encapsulated within polyelectrolyte layers made of CHI/ALG, PAH/ALG and PAH/HA and their viability was evaluated through the resazurin reduction assay and the Live/Dead assay. In these experiments, during the LbL process, polyelectrolyte solutions were used at a concentration of 1mg/mL based on literature. In general, the viability of the encapsulated cells was shown to be very low/absent. Then, as a consequence of the lack of viability of cells encapsulated within polyelectrolyte layers, the LbL technique was applied in cells growing adherent to the surface of cell culture plates. The cells were cultured like in a sandwich, between the surface of the cell culture dish and the polyelectrolyte layers. Also here, the polyelectrolyte solutions were used at a concentration of 1mg/mL during the LbL process. Surprisingly, cell viability was also absent in these systems. A systematic study (dose-effect study) was performed to evaluate the effect of the concentration of the individual polyelectrolytes (ALG, CHI and PAH were studied) in cell viability. Experiments were performed using cells growing adherent to the surface of cell culture plates. The results pointed out that a very high (cytotoxic) concentration of polyelectrolytes had been in use. Also, in general, PAH was much more cytotoxic than CHI, whereas ALG was the less cytotoxic polyelectrolyte. Finally, using alginate and chitosan solutions with adequate concentrations (low concentrations: 50ng/mL and 1μg/mL), the encapsulation of single viable cells was again attempted. Once again, the encapsulated cells were not shown to be viable. In conclusion, the viability of the encapsulated cells is not only dependent on the cytotoxic characteristics (or combined cytotoxic characteristics) of the polyelectrolytes but it seems that, when detached from the culture plates, the cells become too fragile and lose their viability very easily.

Modulação da expressão da proteína XPA em resposta ao tratamento com azul de metileno fotossensibilizado

Reactive oxygen species (ROS) are produced by aerobic metabolism and react with biomolecules, such as lipids, proteins and DNA. In high concentration, they lead to oxidative stress. Among ROS, singlet oxygen (1O2) is one of the main ROS involved in oxidative stress and is one of the most reactive forms of molecular oxygen. The exposure of some dyes, such as methylene blue (MB) to light (MB+VL), is able to generate 1O2 and it is the principle involved in photodynamic therapy (PDT). 1O2 e other ROS have caused toxic and carcinogenic effects and have been associated with ageing, neurodegenerative diseases and cancer. Oxidative DNA damage is mainly repaired by base excision repair (BER) pathway. However, recent studies have observed the involvement of nucleotide excision repair (NER) factors in the repair of this type of injury. One of these factors is the Xeroderma Pigmentosum Complementation Group A (XPA) protein, which acts with other proteins in DNA damage recognition and in the recruitment of other repair factors. Moreover, oxidative agents such as 1O2 can induce gene expression. In this context, this study aimed at evaluating the response of XPA-deficient cells after treatment with photosensitized MB. For this purpose, we analyzed the cell viability and occurrence of oxidative DNA damage in cells lines proficient and deficient in XPA after treatment with MB+VL, and evaluated the expression of this enzyme in proficient and complemented cells. Our results indicate an increased resistance to treatment of complemented cells and a higher level of oxidative damage in the deficient cell lines. Furthermore, the treatment was able to modulate the XPA expression up to 24 hours later. These results indicate a direct evidence for the involvement of NER enzymes in the repair of oxidative damage. Besides, a better understanding of the effects of PDT on the induction of gene expression could be provided

A medida cautelar na ação direta de inconstitucionalidade: uma abordagem pela perspectiva do princípio do acesso à justiça

The present study deals with the caution measure in the direct action of inconstitutionality. The treatment given to the approach is through the principle of access to justice. For this, a construction of the juridical content in the principle of access to justice is proposed, without losing the focus of its characteristic as a metajuridical principle, which is presented in the constitutional field as a fundamental right, generator of a new universality, destined to guarantee the prevalence of an adequate juridical tutelage. Some challenges of the concretizing hermeutics are still shown to give way to principle of access to justice, dealing with certain limitations and proposals. The direct action of inconstitutionality in face of the dissertation, begins to focus on the presentation of the tutelage of urgency, differentiating it from the other brief tutelage and elevating it to the condition of instrument which is indispensable to the principle of access to justice. In the most specific field of the abstract control of constitutionality, the characteristics of the objective process are defined, their sources, amongst which the regimental norms of the Federal Supreme Court and their role in the new constitutional reality. Finally, the caution measure in the direct action of inconstitutionality is presented by the perspective of principle of access to justice, identifying some points: the interpretations of the principle of the natural judge to adapt him to the aspect of continuous and temporarily adequate juridical account, especially when concerned to emergency; the analysis of facts in the direct action; the bonding objective effects and the erga omnes; the effect over the factual and normative plan; the effect of the caution measure over other processes and over the prescriptional course; the polemic of the possibility of caution measure in direct action of inconstitutionality through omission

Revestimento de sementes de milho superdoce (sh2)

A semente de milho doce é leve e rugosa. A rugosidade torna difícil a classificação das sementes quanto à forma e ao tamanho e isso dificulta a semeadura. Uma solução para esse problema seria a utilização da técnica de revestimento. Assim, este trabalho teve por objetivo avaliar diferentes materiais de enchimento, cimentantes e corantes na peletização de sementes de milho superdoce e verificar quais combinações de materiais seriam eficientes na manutenção da qualidade fisiológica das sementes após o armazenamento e que permitissem vazão e distribuição uniformes durante a semeadura. Foram então testados doze materiais de enchimento (calcários 1 e 2, caulim, carvão vegetal ativado, areia, vermiculita, fubá de milho, farinha de trigo, polvilho de mandioca, amido de milho, celite e terra de diatomáceas), dois cimentantes (goma arábica e cascorez extra) e seis corantes (tintas guache, acrílica, plástica e para tecido, corante para alimento e gelatina). As avaliações da qualidade física e fisiológica das sementes revestidas e nuas foram efetuadas por meio dos testes: teor de água, fragmentação, peso de mil sementes, volume aparente e plantabilidade, germinação, primeira contagem da germinação e emergência de plântulas em campo. O revestimento de sementes de milho superdoce proporciona homogeneidade de forma e tamanho às sementes, melhora a vazão e a distribuição dos péletes na semeadura e não compromete a emergência de plântulas em campo depois de quatro meses de armazenamento.

Compósito reforçado com sisal para aplicação na moda

The objective of this research is the fabrication of a composite reinforced with dyed sisal fiber and polyester matrix for application in the fields such as, fashion, clothing, interior textiles; fashion accessories are some of the examples. For the fabrication of the composite, the sisal fibers were subjected to processes such as: chemical treatment with sodium hydroxide (NaOH) in the removal of impurities; bleaching for removing the yellowish color of the natural fiber and dyeing with direct dyes to confer the colors blue, green and orange. The search for new technologies ecologically correct has become a major concern in recent decades. Studies show that composite polymer reinforced by natural fibers is suitable for a large number of applications, and its use is advantageous in terms of economic and ecological. The dyed fibers were cut to a length of 30 mm, is used in the confection of webs. For this purpose, a web preparer by immersion, developed in the Laboratory of Chemical Textile of UFRN. The composite sheets measuring 300 x 300 x3 mm were molded by compression, with unsaturated orthophthalic polyester as matrix, and the samples in sizes 150 x 25 x 3 mm were cut with the aid of a laser machine, to be subjected to traction and flexion. The mechanical properties of traction and flexion in three points were performed in the Laboratory of metal and mechanical tests of Materials Engineering of UFRN. The resulting samples from the tests were evaluated in scanning electron microscope (SEM) at CTGas RN. On the basis of the analysis of the results from the mechanical tests, it was observed that the composite had good mechanical behavior, both in traction as in flexion. Furthermore, it was observed that in the water absorption test, the samples had a different percentage among themselves, this occurred due to the variation of density found in the fibre webs. The images of the SEM showed the failures from the manufacturing process and the adhesion of fibre/matrix. When the samples were prepared with the dyed fibers to be applied in fashion, the results were positive, and it can be concluded that the main objective of this work was achieved

Aspectos metodológicos para análise de depósitos de pulverizações pela determinação dos depósitos pontuais

Objetivou-se com este trabalho avaliar a variabilidade dos depósitos de traçadores, simulando herbicidas aplicados em pós-emergência, em populações de Brachiaria plantaginea e Commelina benghalensis infestantes da cultura da soja. Os depósitos dos traçadores foram também avaliados em plantas da cultura, utilizando-se o pulverizador de barra tratorizado, com pontas de jato plano da série 110-SF-03, aplicando o volume de 250 L ha-1 de calda preparada com 0,18% de corante Azul Brilhante e 0,18% de Amarelo Saturn Yellow. Os alvos naturais utilizados foram: plantas de soja com 150 repetições; B. plantaginea no estádio de duas a oito folhas, coletadas na linha da cultura com 141 repetições; e B. plantaginea e C. benghalensis nas entrelinhas, com 150 e 50 repetições, respectivamente. Os alvos artificiais foram constituídos por lâminas distribuídas a 0, 12,2 e 22,5 cm da linha da cultura. Após a aplicação, os alvos foram coletados individualmente e lavados com 30, 20 e 15 mL de água deionizada, para soja, lâminas e plantas daninhas, respectivamente. Estas originaram as amostras analisadas em espectrofotômetro, estimando-se o depósito de calda em µL por planta e µL cm² de área foliar. Foram ajustadas curvas de regressão entre os depósitos unitários e as freqüências acumuladas, utilizando-se o modelo de Gompertz. As relações entre os depósitos máximos e mínimos foram de 7, 4, 10 e 6 para soja, C. benghalensis e B. plantaginea na linha e na entrelinha, respectivamente. As plantas de B. plantaginea da entrelinha receberam, em média, 34% a mais de depósito do que as plantas da linha.

Degradação luminosa e retenção foliar dos corantes azul brilhante FDC-1 e amarelo tartrasina FDC-5 utilizados como traçadores em pulverizações

Três estudos foram conduzidos no Núcleo de Pesquisas Avançadas em Matologia (NUPAM) pertencente à UNESP/FCA - campus de Botucatu-SP, com o objetivo de avaliar a estabilidade dos corantes Azul Brilhante FDC-1 e Amarelo Tartrasina FDC-5 quanto a diferentes períodos de exposição à luz solar e contato com folhas de Eichhornia crassipes. No primeiro estudo, soluções de 0,3125, 0,625, 1,25, 2,5, 5, 10 e 20 ppm dos corantes Azul Brilhante FDC-1 e Amarelo Tartrasina FDC-5 foram acondicionadas em tubos de quartzo hermeticamente fechados e submetidos a 0, 0,5, 1, 2, 4, 6 e 10 horas de exposição à luz solar e ao escuro. Ao final de cada período, amostras de 10 mL foram retiradas dos tubos e analisadas. No segundo estudo, os tratamentos foram dispostos no esquema fatorial 2x7: duas condições luminosas (escuro e pleno sol) e sete períodos de exposição (0, 0,5, 1, 2, 4, 6 e 10 horas), com seis repetições. Com o auxílio de micropipeta, oito gotas de 5 µL das soluções Azul Brilhante e Amarelo Tartrasina a 4.000 ppm foram depositadas em placas de Petri de vidro. Após o término dos períodos de exposição, as placas foram lavadas com 50 mL de água destilada, com o objetivo de extrair o corante depositado sobre elas. No terceiro estudo, adotaram-se os mesmos tratamentos do segundo experimento, com quatro repetições, porém as soluções foram depositadas sobre as folhas de plantas de Eichhornia crassipes. Foram adotados também os mesmos procedimentos de extração dos corantes após o término dos períodos de exposição. As soluções finais obtidas nos três estudos foram submetidas à leitura óptica de absorbância em espectrofotômetro UV-visível nos comprimentos de onda de 630 e 427 nm, para os corantes Azul Brilhante FDC-1 e Amarelo Tartrasina FDC-5, respectivamente. As várias concentrações das soluções de ambos os corantes não sofreram degradação pela luz solar quando submetidas aos vários períodos de incidência luminosa nos tubos de quartzo (ambiente fechado), visto que as curvas de recuperação apresentaram equações semelhantes àquelas concentrações que foram mantidas no escuro. A mesma estabilidade também foi observada quando os corantes foram submetidos à luz solar em ambiente aberto, ou seja, nas placas de Petri. O corante Amarelo Tartrasina também se apresentou muito estável quando depositado sobre as folhas de E. crassipes, independentemente da exposição ou não à luz solar. Para o corante Azul Brilhante, ocorreram significativas perdas de 7,8 e 18,6% quando esteve depositado na superfície da folha de aguapé pelo período de 10 horas sob condições de escuro e plena luz solar, respectivamente.

Depósitos de calda de pulverização nas faces adaxial e abaxial de folhas de Eichhornia crassipes dispostas em diferentes ângulos

Estudos foram conduzidos com o objetivo de avaliar os depósitos de gotas pulverizadas através de dois tipos de pontas sobre as faces adaxial e abaxial de folhas de Eichhornia crassipes dispostas em diferentes ângulos. No primeiro estudo, os tratamentos foram dispostos no esquema fatorial 2x4x7: dois tipos de pontas (TX12 e XR11002VS), quatro ângulos verticais (0º, 30º, 60º e 90º) e sete ângulos horizontais (0º, 15º, 30º, 45º, 60º, 75º e 90º). No ângulo vertical de 90º a lâmina foliar foi posicionada paralelamente ao sentido de deslocamento do jato de pulverização; e no ângulo horizontal de 90º a folha foi posicionada perpendicularmente ao plano do solo. Como traçadores, foram utilizadas soluções de 1.000 ppm do corante Azul FDC-1 e 3.500 ppm do corante Amarelo Tartrasina para as pontas tipo leque e cone, respectivamente. No segundo estudo, os tratamentos foram dispostos no esquema fatorial 2x2x3: dois tipos de pontas (TX12 e XR11002VS), dois tipos de calda (com e sem Aterbane BR a 0,5%) e três ângulos horizontais (0º, 45º e 90º). Adotou-se o ângulo vertical de 90º como padrão para todos os tratamentos. Soluções de 1.000 ppm do corante Azul FDC-1 e 3.500 ppm do corante Amarelo Tartrasina foram utilizadas como traçadores para a calda com e sem surfatante, respectivamente. Os resultados do primeiro estudo revelaram que os depósitos observados em toda a folha e na face adaxial das lâminas foliares de aguapé diminuíram à medida que se aumentou a angulação vertical, independentemente da ponta utilizada. Os menores depósitos sempre estiveram relacionados ao ângulo vertical de 90º, independentemente do ângulo horizontal utilizado. Não foi detectado nenhum depósito na face abaxial das folhas de aguapé em todas as combinações dos fatores estudados. No segundo estudo também foram observados os mesmos decréscimos no volume de calda depositado em toda a folha e na face adaxial à medida que se aumentou a angulação vertical das lâminas foliares. As duas pontas proporcionaram depósitos nulos na face abaxial quando o surfatante não foi utilizado; entretanto, a adição do surfatante à calda incrementou significativamente os depósitos nesta face da folha do aguapé.

Efeito de pontas de pulverização e de arranjos populacionais de plantas de Eichhornia crassipes e Salvinia auriculata na deposição de calda de pulverização sobre plantas de Pistia stratiotes

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)