Production of porous aluminium and iron sulphated oxyhydroxides using industrial grade coagulants for optimised arsenic removal from groundwater

The optimisation of Fe and Al oxyhydroxide materials produced using industrial grade coagulants is presented in this work. The effects of synthesis pH and post-synthesis washing procedure onto the arsenic adsorption capacity of the materials were investigated. It was shown that the materials produced at higher pH were more efficient in removing As(V), especially after cleaning procedure. The materials produced at lower pH were less efficient in removing As(V) but the higher presence of sulphate groups in the materials produced at lower pH enhanced As(III) adsorption. Most performing materials can remove up to 84.7 mg As(V) g^-1 or 77.9 mg As(III) g^-1.

Application of surface plasmon polaritons in the laser ablation and characterisation of thin aluminium films

Surface modification of thin aluminium films is both produced and characterised by exciting surface plasmon polaritons in an attenuated total reflection geometry: silica prism/aluminium/aluminium oxide system. The modification is performed, under ambient conditions, by exposure to a low fluence (

Contrasting damage characteristics in direct incidence and surface plasmon mediated single-shot laser ablation of aluminium films

Thin, oxidised Al films grown an one face of fused silica prisms are exposed. tinder ambient conditions, to single shots from an excimer laser operating at wavelength 248 nm. Preliminary characterisation of the films using attenuated total reflection yields optical and thickness data for the Al and Al oxide layers; this step facilitates the subsequent, accurate tuning of the excimer laser pulse to the: surface plasmon resonance at the Al/(oxide)/air interface and the calculation of the fluence actually absorbed by the thin film system. Ablation damage is characterised using scanning electron, and atomic force microscopy. When the laser pulse is incident, through the prism on the sample at less than critical angle, the damage features are molten in nature with small islands of sub-micrometer dimension much in evidence, a mechanism of film melt-through and subsegment blow-off due to the build up of vapour pressure at the substrate/film interface is appropriate. By contrast, when the optical input is surface plasmon mediated, predominately mechanical damage results with the film fragmenting into large flakes of dimensions on the order of 10 mu m. It is suggested that the ability of surface plasmons to transport energy leads to enhanced, preferential absorption of energy at defect sites causing stress throughout the film which exceeds the ultimate tensile stress for the film: this in turn leads to film break-up before melting can onset. (C) 1998 Elsevier Science B.V.

Insight of the interface of electroless Ni-P/SiC composite coating on aluminium alloy, LM24

Electroless nickel composite coatings with silicon carbide, SiC, as reinforcing particles deposited with Ni–P onto aluminium alloy, LM24, having zincating as under layer were subjected to heat treatment using air furnace. The changes at the interface were investigated using scanning electron microscope (SEM) and energy dispersive X-ray (EDX) to probe the chemistry changes upon heat treatment. Microhardness tester with various loads using both Knoop and Vickers indenters was used to study the load effect clubbed with the influence of second phase particles on the coating at the vicinity of the interface. It was observed that zinc was absent at the interface after elevated temperature heat treatment at 400–500 °C. Precipitation of copper and nickel with a distinct demarcation (copper rich belt) along the coating interface was seen with irregular thickness of the order of 1 μm. Migration of copper from the bulk aluminium alloy could have been the factor. Brittleness of the coating was confirmed on heat treatment when indented with Vickers. However, in composite coating the propagation of the microcrack was stopped by the embedded particles but the microcracks continue in the matrix when not interrupted by second phase particles (SiC).

Phase composition, microstructure and microhardness of electroless nickel composite coating co-deposited with SiC on cast aluminium LM24 alloy substrate

Electroless Ni–P (EN) and composite Ni–P–SiC (ENC) coatings were developed on cast aluminium alloy substrate, LM24. The coating phase composition, microstructure and microhardness were investigated using X-ray diffraction (XRD), scanning electron microscopy (SEM) and microhardness tester, respectively, on as-plated and heat-treated specimens. The original microstructure of the Ni–P matrix is not affected by the inclusion of the hard particles SiC. No formation of Ni–Si phase was observed up to 500 °C of heat treatment. The microhardness is increased on incorporation of SiC in Ni–P matrix. The hardening mechanism is the formation of intermetallic phase Ni3P on annealing at elevated temperature.

Characterisation of phase composition, microstructure and microhardness of electroless nickel composite coating co-deposited with SiC on casting aluminium LM24 alloy substrate

Electroless Ni-P (EN) and composite Ni-P-SiC (ENC) coatings were developed on cast aluminium alloy, LM24. The coating phase composition, microstructure and microhardness were investigated using X-ray diffraction (XRD), scanning electron microscopy (SEM) and microhardness tester, respectively, on as-plated and heat-treated specimens. The original microstructure of the Ni-P matrix is not affected by the inclusion of the hard particles SiC. No formation of Ni-Si phase was observed upto 500°C of heat treatment. The microhardness is increased on incorporation of SiC in Ni-P matrix. The hardening mechanism is the formation of intermetallic phase Ni3P on annealing at elevated temperature. Overall, the composite coating (ENC) was found to be superior as compared to particles free (EN) coating in both as-deposited and heat-treated conditions.

Micro-scale abrasion behaviour of electroless Ni-P-SiC coating on aluminium alloy

Electroless nickel (EN) and electroless nickel composite (ENC) coatings were deposited on aluminium alloy substrate, LM24. The micro abrasion test was conducted to study the wear behaviour of the coatings with the effect of SiC concentration. Microhardness of the coatings was tested also. The wear scars were analysed using optical microscope and scanning electron microscope (SEM). The wear resistance was found to be improved in composite coating that has higher microhardness as compared to particles free and the bare aluminium substrate. In as-deposited condition for the composite coating, the wear volume increases on increase in SiC percentage in the coating but is found to be minimum for lower SiC percentage. The increase in hardness on heat treatment at 400°C is due to the hardening or grain coarsening with the formation Ni3P.

Modelling Cohesive-Frictional Particulate Solids for Bulk Handling Applications

Many powders and particulate solids are cohesive in nature and the strength often exhibits dependence on the consolidation stress. As a result, the stress history in the material leading up to a handling scenario needs to be considered when evaluating its handleability. This paper outlines the development of a DEM contact model accounting for plasticity and adhesion force, which is shown to be suitable for modelling the stress history dependent cohesive strength. The model was used to simulate the confined consolidation and the subsequent unconfined loading of iron ore fines with particle sizes up to 1.18mm. The predicted flow function was found to be comparable to the experimental results. 

Fermi level de-pinning of aluminium contacts to n-type germanium using thin atomic layer deposited layers

Fermi-level pinning of aluminium on n-type germanium (n-Ge) was reduced by insertion of a thin interfacial dielectric by atomic layer deposition. The barrier height for aluminium contacts on n-Ge was reduced from 0.7 eV to a value of 0.28 eV for a thin Al2O3 interfacial layer (∼2.8 nm). For diodes with an Al2O3 interfacial layer, the contact resistance started to increase for layer thicknesses above 2.8 nm. For diodes with a HfO2 interfacial layer, the barrier height was also reduced but the contact resistance increased dramatically for layer thicknesses above 1.5 nm.

Aluminium toxicity in wheat and rye

Com o presente trabalho pretendeu-se determinar e compreender melhor quais os alvos do Alumínio (Al) nas plantas, e contribuir para um melhor entendimento dos mecanismos de tolerância presentes em genótipos com elevado grau de tolerância ao Al. O Al é um dos maiores constituintes do solo e torna-se biodisponível em solos com baixo pH. Nesses casos, a exposição ao Al afecta negativamente o crescimento das plantas conduzindo a uma diminuição da produção. Estes factos são especialmente visíveis nos cereais, sendo a exposição ao Al uma das principais causas das quebras de produção nestas espécies. O Capítulo I consiste numa revisão geral sobre a toxicidade do Al nas plantas, apontando os seus principais alvos. Apresenta também os mecanismos de resistência, que inclui Al-destoxificação externa e interna, em diferentes espécies. O Capítulo II aborda os estudos sobre a exposição de curto prazo ao Al em duas espécies de cereais: Triticum aestivum L. e Secale cereale L., tendo-se sempre utilizado um genótipo Al-tolerante e um Al-sensível para cada espécie. Este capítulo está dividido em três estudos: no Capítulo II.1 realça-se o efeito da exposição a 185 μM de Al no equilíbrio nutricional em trigo. Verificou-se que em ambos os genótipos (sensível e tolerante) o perfil de macro e micro nutrientes se alterou, tendo uma interferência negativa, sobretudo no nível de P, Mg e K. Além disso, registaram-se diferenças na diferenciação da endoderme consoante o grau de tolerância/sensibilidade do genótipo. No Capítulo II.2 apresenta-se uma visão mais abrangente dos efeitos da exposição a 185 μM de Al em trigo, incluindo parâmetros fisiológicos, estruturais, citológicos e genotóxicos. Demonstra-se, pela primeira vez, que a progressão do ciclo celular é diferentemente regulada, dependendo da tolerância/sensibilidade do genótipo e que, mesmo em zonas já diferenciadas da raiz a exposição ao Al leva à deposição de calose. O Capítulo II.3 aborda os efeitos da exposição de 1.1 mM de Al em centeio, numa perspectiva bastante alargada. Apresenta-se o desequilíbrio nutricional, sobretudo no genótipo sensível, assim como a translocação de Al para a parte aérea nesse mesmo genótipo. Analisa-se também o comportamento de ambos os genótipos no que se refere ao ciclo celular, diferenciação da endoderme, crescimento radicular, reservas de hidratos de carbono, entre outros. Os resultados apontam para estratégias bem definidas adoptadas pelo genótipo tolerante de forma a minimizar a acção do Al no sistema radicular. O Capítulo III compreende a exposição longa ao Al. Dois genótipos de centeio com diferentes graus de tolerância ao Al foram expostos a 1.11 mM e 1.85 mM de Al durante 21 dias, tendo sido usados dois pontos de amostragem (15 e 21 dias). Este capítulo está dividido em dois estudos: No Capítulo III. 1 analisamse os mecanismos antioxidantes (folhas e raízes) como resposta à exposição ao Al, dando-se especial atenção ao ciclo do ascorbato-glutationas. A exposição ao Al levou a stress oxidativo e a alterações na actividade de enzimas antioxidantes e no conteúdo de antioxidantes não-enzimáticos. Demonstra-se que os dois órgãos apresentam respostas diferentes à exposição ao Al e que a capacidade de sobreviver em ambientes ricos em Al depende da eficácia da resposta antioxidante. Para além disso, a resposta do ciclo ascorbato-glutationas parece estar dependente do tipo de órgão, grau de tolerância e do tempo de exposição ao Al. No Capítulo III. 2 analisam-se os efeitos da exposição ao Al na fotossíntese. Verificou-se que o Al afecta negativamente a taxa fotossintética em ambos os genótipos, embora as alterações que o Al provoca nas trocas gasosas e no Ciclo de Calvin sejam dependentes do genótipo. Verificou-se também que os danos no genótipo sensível surgem mais cedo do que no genótipo tolerante, mas que ambos apresentam susceptibilidade ao Al após exposição de longo termo. Por fim, no Capítulo IV são apresentadas as conclusões da Tese de Doutoramento.

Asymmetric rolling of 5182 aluminium alloy and interstitial free steel sheets

This Ph.D. research focuses on asymmetric rolling (ASR), as an alternative method for improving mechanical responses of aluminium-magnesium alloy and interstitial free (IF) steel regarding industrial requirements. Aluminium alloys are attractive materials in various industries due to their appropriate properties such as low density and corrosion resistance; however, their low formability has limited their applications. As formability of aluminium alloys can be improved through texture development, part of this dissertation is dedicated to producing the desired crystallographic texture with the ASR process. Two types of ASR (i.e. reverse and continuous asymmetric rolling) were investigated. The impact of shear deformation imposed by ASR processes on developing the desirable texture and consequently on mechanical behaviours was observed. The developed shear texture increased the normal and also planar anisotropy. Texture evolution during plastic deformation as well as induced mechanical behaviour were simulated using the “self-consistent” and Taylor models. Interstitial free (IF) steel was the second material selected in this dissertation. Since IF steel is one of the most often used materials in automotive industries it was chosen to investigate the effect of shear deformation through ASR on its properties. Two types of reverse and continuous asymmetric rolling were carried out to deform IF steel sheets. The results of optical microscopy and atomic force microscopy observations showed no significant difference between the grains’ morphology of asymmetric and conventionally rolled samples, whereas the obtained results of transmission electron microscopy indicated that fine and equiaxed dislocation cells were formed through the asymmetric rolling process. This structure is due to imposed shear deformation during the ASR process. Furthermore, the mechanical behaviour of deformed and annealed sheets was evaluated through uniaxial tensile tests. Results showed that at low thickness reductions (18%) the asymmetric rolled sample presented higher stress than that of the conventionally rolled sheet; while for higher thickness reductions (60%) the trend was reversed. The texture analyses indicated that intense rolling texture components which developed through 60% thickness reduction of conventional rolling cause a relatively higher stress; on the contrary the fine structure resulting from ASR appears to be the source of higher stress observed after pre-deformation of 18%.

Absorption coefficient of particulate matter on the south-west coast of Europe: a contribution to the validation of the MERIS-Medium Resolution Imaging Spectrometer sensor

Dissolved oxygen (DO) is one of the most important environmental variables of water quality, especially for marine life. Consequently, oxygen is one of the Chemical Quality Elements required for the implementation of European Union Water Framework Directive. This study uses the example of the Ria Formosa, a meso-tidal lagoon on the south coast of Portugal to demonstrate how monitoring of water quality for coastal waters must be well designed to identify symptoms of episodic hypoxia. New data from the western end of the Ria Formosa were compared to values in a database of historical data and in the published literature to identify long-term trends. The dissolved oxygen concentration values in the database and in the literature were generally higher than those found in this study, where episodic hypoxia was observed during the summer. Analysis of the database showed that the discrepancy was probably related with the time and the sites where the samples had been collected, rather than a long-term trend. The most problematic situations were within the inner lagoon near the city of Faro, where episodic hypoxia (<2 mg dm3 DO) occurred regularly in the early morning. These results emphasise the need for a balanced sampling strategy for oxygen monitoring which includes all periods of the day and night, as well as a representative range of sites throughout the lagoon. Such a strategy would provide adequate data to apply management measures to reduce the risk of more persistent hypoxia that would impact on the ecological, important natural resource. economic and leisure uses of this important natural resource.

Novel particulate antibiotic-loaded platforms as sustained drug delivery systems for bone infection treatment

Tese de doutoramento, Farmácia (Tecnologia Farmacêutica), Universidade de Lisboa, Faculdade de Farmácia, 2015