Análise Biomecânica em implantes com diferentes tipos de conexão: estudo pelo MEF-3D

The aim of this study was to evaluate the biomechanical behavior of different implant connection types, by means of three-dimensional finite element analysis. 3 Three-dimensional models were created with a graphic modeling software: SolidWorks 2006 and Rhinoceros 4.0, and InVesalius (CTI, São Paulo, Brasil), the bone was obtained by computerized tomography of a sagittal section of the molar region. The model was composed by bone block with an implant (4 x 10 mm) (Conexão Sistemas de Prótese, São Paulo), with different implant connections: external hex, internal hex and Morse-taper with the corresponding prosthetic component Ucla or Morse-taper abutment. The Three-dimensional models were transferred to finite element software Femap 10.0 (Siemens PLM Software Inc., CA, USA), to generate a mesh, boundary conditions and loading. An axial (200N) and oblique load (100N) was applied on the occlusal surface of the crowns. Analyses were performed using the finite element software NEiNastran 9.0 (Noran Engineering, Inc., USA) and transferred to the Femap 10.0 to obtain the results; after the results were visualized using von Mises stress maps and Maximum stress principal. The results showed the stress distribution was similar between models, with a little superiority of Morse-taper connection. It was concluded that: the three connection types were biomechanical viable; The Morse-taper connection presented the better internal stress distribution; there was not significant biomechanical differences on the bone.

Influência do material oclusal na distribuição de tensões em próteses implantossuportadas unitárias

Objective: the aim of this study was to evaluate the influence of occlusal veneering material in single fixed implant-supported crowns through the 3-D finite element method. Material and methods: Four models were fabricated using the Rhinoceros 4.0, SolidWorks, and InVesalius softwares. Each model represented a block of mandibular bone with an external hexagon implant of 5 mm x 10 mm and different veneering materials including NiCr (1), porcelain (2), composite resin (3), and acrylic resin (4). An axial load of 200 N and an oblique load of 100 N were applied. Results: model (2) with porcelain veneering presented a lower stress concentration for the NiCr framework, followed by the composite resin and acrylic resin. The stress distribution to the implant and bone tissue was similar for all models. Conclusions: there is no difference of stress distribution to the implant and supporting structures by varying the veneering material of a single implant-supported prosthesis.

Influência do material oclusal na distribuição de tensões em próteses implantossuportadas unitárias

Objective: the aim of this study was to evaluate the influence of occlusal veneering material in single fixed implant-supported crowns through the 3-D finite element method. Material and methods: Four models were fabricated using the Rhinoceros 4.0, SolidWorks, and InVesalius softwares. Each model represented a block of mandibular bone with an external hexagon implant of 5 mm x 10 mm and different veneering materials including NiCr (1), porcelain (2), composite resin (3), and acrylic resin (4). An axial load of 200 N and an oblique load of 100 N were applied. Results: model (2) with porcelain veneering presented a lower stress concentration for the NiCr framework, followed by the composite resin and acrylic resin. The stress distribution to the implant and bone tissue was similar for all models. Conclusions: there is no difference of stress distribution to the implant and supporting structures by varying the veneering material of a single implant-supported prosthesis.

Análise das tensões em próteses implantossuportadas esplintadas, variando o tipo de conexão protética e a inclinação do implante: estudo pelo método dos elementos finitos tridimensionais não linear

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Monitoramento de integridade estrutural e de sistemas utilizando dispositivos de baixo custo

Pós-graduação em Engenharia Mecânica - FEB

Desenvolvimento de uma rede de sensores sem fio aplicada no monitoramento da variabilidade térmica em casas de vegetação

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Análise da distribuição de tensões em reabilitação com implantes cone morse em maxilar posterior: estudo pelo MEF 3D não linear

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Numerical analysis of a modified evacuated tubes solar collector

The need for renewable energy sources, facing the consequences of Climate Change, results in growing investment for solar collectors’ use. Research in this field has accompanied this expansion and evacuated tube solar collector stands as an important study focus. Thus, several works have been published for representing the stratification of the fluid inside the tubes and the reservoir, as well as analytical modeling for the heat flow problem. Based on recent publications, this paper proposes the study of solar water heating with evacuated tubes, their operation characteristics and operating parameters. To develop this work, a computational tool will be used - in this case, the application of computational fluid dynamics (CFD) software. In possession of the implemented model, a numerical simulation will be performed to evaluate the behavior of the fluid within this solar collector and possible improvements to be applied in the model.

Concepção, modelagem, simulação e usinagem de um aerofólio automotivo auxiliado por computador

With the advancement of computer technology and the availability of technology computer aided design (CAD) errors in the designs are getting smaller. To this end the project aims to assess the reliability of the machine (CNC), which was designed by students of mechanical engineering college engineering - UNESP Bauru, by designing, modeling, simulation and machining an airfoil automotive. The profile template selected for the study will be a NACA 0012 machined plates in medium density fiberboard (MDF) and will be performed with a structural analysis simulation using finite elements and a software CFD (Computational Fluid Dynamics), and test the real scale model in a wind tunnel. The results obtained in the wind tunnel and CFD software will be compared to see the error in the machining process.

Analisys of thermal efficiency of a modified solar collector type evacuated tube

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Proposta de um sistema de monitoramento do processo de retificação plana baseado em plataforma de hardware livre e sensor de baixo custo

O processo de retificação é considerado um dos últimos na cadeia de produção de peças de precisão. Assim, é essencial ter um sistema de monitoramento confiável para este processo. Neste trabalho é proposto um sistema de medição de vibração, rápido e versátil, baseado na plataforma de prototipagem eletrônica de hardware livre Arduino, com objetivo de monitorar em tempo real o processo de retificação plana, especialmente no que diz respeito à condição da peça retificada. Para este trabalho ensaios experimentais foram realizados numa máquina retificadora plana, empregando um rebolo de óxido de alumínio e uma peça de aço ABNT 1020. Por meio de um sensor piezelétrico de PZT (Pb-Lead Zirconate Titanate) de baixo custo, instalado junto à peça e conectado a uma das portas analógicas do hardware, foi possível medir o sinal de vibração durante o processo de retificação. Verificou-se que, a medida com que o rebolo perdia sua capacidade de corte, em função das consecutivas passadas sobre a peça, ocorria também uma significativa diminuição dos valores médios do sinal de vibração. Tal diminuição do sinal de vibração pode indicar o momento que o rebolo deve ser dressado, permitindo monitorar a qualidade superficial da peça durante o processo de retificação, evitando danos como é o caso da queima superficial. O princípio de operação e as principais características dessa técnica foram investigados, bem como algumas de suas limitações práticas.

Avaliação da distribuição das forças produzidas com arco lingual removível pelo método de elementos finitos

Pós-graduação em Ciências Odontológicas - FOAR

Concepção detalhada de uma bancada para simular esforços mecânicos em colunas de perfuração

In this work we study the construction of a test rig made to simulate the Mechanical efforts in wich a drillstring is submitted. The model is based on the rig built at IDS, Germany. There are some fault liabilities while doing the project of the axis. Therefore it's important to analyze and take knowledge of this efforts in order to predict failures like rupture or fatigue collapse. The main objective of this theis is to show the operating principle of the test rig and it's construction. The accomplished study allow us to predict the drillstring behavior and from the economic point of view that is very important because failures results in equipments maintenance that requires time and money causing prejudice to the company. Using SolidWorks, a simulation software, the thesis approaches all the mechanical parts required for it's construction as well as it's working principle. Acquisition sensors like strain gauges, accelerometer, and torque transductor were also used in this model. The objective of this thesis is to create a simulation model to be eventually at FEG(UNESP). During the development of the study, it was possible to learn more about the drilling process and the mechanical efforts in which the drill pipe is submitted. The accomplished contributed with knowledge for the student in the drilling process area. Also during the development of the study it was possible to have contact with different areas of engineering but the study is specifically directed to the construction of the test rig. Therefore the main theme of this thesis is to show the operating principle of the test rig and it's construction

Concepção detalhada de uma bancada para simular esforços mecânicos em colunas de perfuração

In this work we study the construction of a test rig made to simulate the Mechanical efforts in wich a drillstring is submitted. The model is based on the rig built at IDS, Germany. There are some fault liabilities while doing the project of the axis. Therefore it's important to analyze and take knowledge of this efforts in order to predict failures like rupture or fatigue collapse. The main objective of this theis is to show the operating principle of the test rig and it's construction. The accomplished study allow us to predict the drillstring behavior and from the economic point of view that is very important because failures results in equipments maintenance that requires time and money causing prejudice to the company. Using SolidWorks, a simulation software, the thesis approaches all the mechanical parts required for it's construction as well as it's working principle. Acquisition sensors like strain gauges, accelerometer, and torque transductor were also used in this model. The objective of this thesis is to create a simulation model to be eventually at FEG(UNESP). During the development of the study, it was possible to learn more about the drilling process and the mechanical efforts in which the drill pipe is submitted. The accomplished contributed with knowledge for the student in the drilling process area. Also during the development of the study it was possible to have contact with different areas of engineering but the study is specifically directed to the construction of the test rig. Therefore the main theme of this thesis is to show the operating principle of the test rig and it's construction

Analysis of energy dissipation in stirred suspension polymerisation reactors using computational fluid dynamics

This work evaluates the spatial distribution of normalised rates of droplet breakage and droplet coalescence in liquidliquid dispersions maintained in agitated tanks at operation conditions normally used to perform suspension polymerisation reactions. Particularly, simulations are performed with multiphase computational fluid dynamics (CFD) models to represent the flow field in liquidliquid styrene suspension polymerisation reactors for the first time. CFD tools are used first to compute the spatial distribution of the turbulent energy dissipation rates (e) inside the reaction vessel; afterwards, normalised rates of droplet breakage and particle coalescence are computed as functions of e. Surprisingly, multiphase simulations showed that the rates of energy dissipation can be very high near the free vortex surfaces, which has been completely neglected in previous works. The obtained results indicate the existence of extremely large energy dissipation gradients inside the vessel, so that particle breakage occurs primarily in very small regions that surround the impeller and the free vortex surface, while particle coalescence takes place in the liquid bulk. As a consequence, particle breakage should be regarded as an independent source term or a boundary phenomenon. Based on the obtained results, it can be very difficult to justify the use of isotropic assumptions to formulate particle population balances in similar systems, even when multiple compartment models are used to describe the fluid dynamic behaviour of the agitated vessel. (C) 2011 Canadian Society for Chemical Engineering