Vibration analysis for Bearing outer race condition diagnostics

This paper investigates defect detection methodologies for rolling element bearings through vibration analysis. Specifically, the utility of a new signal processing scheme combining the High Frequency Resonance Technique (HFRT) and Adaptive Line Enhancer (ALE) is investigated. The accelerometer is used to acquire data for this analysis, and experimental results have been obtained for outer race defects. Results show the potential effectiveness of the signal processing technique to determine both the severity and location of a defect. The HFRT utilizes the fact that much of the energy resulting from a defect impact manifests itself in the higher resonant frequencies of a system. Demodulation of these frequency bands through use of the envelope technique is then employed to gain further insight into the nature of the defect while further increasing the signal to noise ratio. If periodic, the defect frequency is then present in the spectra of the enveloped signal. The ALE is used to enhance the envelope spectrum by reducing the broadband noise. It provides an enhanced envelope spectrum with clear peaks at the harmonics of a characteristic defect frequency. It is implemented by using a delayed version of the signal and the signal itself to decorrelate the wideband noise. This noise is then rejected by the adaptive filter that is based upon the periodic information in the signal. Results have been obtained for outer race defects. They show the effectiveness of the methodology to determine both the severity and location of a defect. In two instances, a linear relationship between signal characteristics and defect size is indicated.

Susteinable steelmaking by process integration

Environmental issues, including global warming, have been serious challenges realized worldwide, and they have become particularly important for the iron and steel manufacturers during the last decades. Many sites has been shut down in developed countries due to environmental regulation and pollution prevention while a large number of production plants have been established in developing countries which has changed the economy of this business. Sustainable development is a concept, which today affects economic growth, environmental protection, and social progress in setting up the basis for future ecosystem. A sustainable headway may attempt to preserve natural resources, recycle and reuse materials, prevent pollution, enhance yield and increase profitability. To achieve these objectives numerous alternatives should be examined in the sustainable process design. Conventional engineering work cannot address all of these substitutes effectively and efficiently to find an optimal route of processing. A systematic framework is needed as a tool to guide designers to make decisions based on overall concepts of the system, identifying the key bottlenecks and opportunities, which lead to an optimal design and operation of the systems. Since the 1980s, researchers have made big efforts to develop tools for what today is referred to as Process Integration. Advanced mathematics has been used in simulation models to evaluate various available alternatives considering physical, economic and environmental constraints. Improvements on feed material and operation, competitive energy market, environmental restrictions and the role of Nordic steelworks as energy supplier (electricity and district heat) make a great motivation behind integration among industries toward more sustainable operation, which could increase the overall energy efficiency and decrease environmental impacts. In this study, through different steps a model is developed for primary steelmaking, with the Finnish steel sector as a reference, to evaluate future operation concepts of a steelmaking site regarding sustainability. The research started by potential study on increasing energy efficiency and carbon dioxide reduction due to integration of steelworks with chemical plants for possible utilization of available off-gases in the system as chemical products. These off-gases from blast furnace, basic oxygen furnace and coke oven furnace are mainly contained of carbon monoxide, carbon dioxide, hydrogen, nitrogen and partially methane (in coke oven gas) and have proportionally low heating value but are currently used as fuel within these industries. Nonlinear optimization technique is used to assess integration with methanol plant under novel blast furnace technologies and (partially) substitution of coal with other reducing agents and fuels such as heavy oil, natural gas and biomass in the system. Technical aspect of integration and its effect on blast furnace operation regardless of capital expenditure of new operational units are studied to evaluate feasibility of the idea behind the research. Later on the concept of polygeneration system added and a superstructure generated with alternative routes for off-gases pretreatment and further utilization on a polygeneration system producing electricity, district heat and methanol. (Vacuum) pressure swing adsorption, membrane technology and chemical absorption for gas separation; partial oxidation, carbon dioxide and steam methane reforming for methane gasification; gas and liquid phase methanol synthesis are the main alternative process units considered in the superstructure. Due to high degree of integration in process synthesis, and optimization techniques, equation oriented modeling is chosen as an alternative and effective strategy to previous sequential modelling for process analysis to investigate suggested superstructure. A mixed integer nonlinear programming is developed to study behavior of the integrated system under different economic and environmental scenarios. Net present value and specific carbon dioxide emission is taken to compare economic and environmental aspects of integrated system respectively for different fuel systems, alternative blast furnace reductants, implementation of new blast furnace technologies, and carbon dioxide emission penalties. Sensitivity analysis, carbon distribution and the effect of external seasonal energy demand is investigated with different optimization techniques. This tool can provide useful information concerning techno-environmental and economic aspects for decision-making and estimate optimal operational condition of current and future primary steelmaking under alternative scenarios. The results of the work have demonstrated that it is possible in the future to develop steelmaking towards more sustainable operation.

Effect of cocaine on periadolescent rats with or without early maternal separation

Cocaine-induced behavioral sensitization and weight loss were investigated in periadolescent Wistar rats kept with their mothers or subjected to repeated maternal separation. Litters allocated to the separation procedure were placed in a temperature-controlled (33ºC) chamber for 3 h per day from postnatal day 6 (P6) to P20. Non-handled rats were left undisturbed until weaning. Treatments were started on P30-31 and the test was performed on P36-37. Animals received injections of saline or cocaine (10 mg/kg, sc) twice daily for 5 days. On day 6 all animals received saline. On day 7 animals were challenged with 10 mg/kg cocaine and their locomotion was evaluated in activity cages. A third group received saline throughout the 7-day period. Body weights were recorded on P30-31 and P36-37. Two-way ANOVA on body weights showed a main effect of treatment group (F(1,35) = 10.446, P = 0.003; N = 10-12). Non-handled rats treated with cocaine for 5 days gained significantly less weight, while no significant effect was observed in maternally separated rats. Two-way ANOVA revealed a main effect of drug treatment on locomotor activity (F(2,32) = 15.209, P<0.001; N = 6-8), but not on rearing condition (F(1,32)<0.001, P = 0.998). Animals pretreated with cocaine showed a clear behavioral sensitization relative to the saline group. No difference in the magnitude of sensitization was found between separated and non-handled animals. Only the effect of cocaine on weight gain was significantly affected by repeated episodes of early maternal separation during the pre-weaning period.

Large-eddy simulation of wind flows over complex terrains for wind energy applications

Wind energy has obtained outstanding expectations due to risks of global warming and nuclear energy production plant accidents. Nowadays, wind farms are often constructed in areas of complex terrain. A potential wind farm location must have the site thoroughly surveyed and the wind climatology analyzed before installing any hardware. Therefore, modeling of Atmospheric Boundary Layer (ABL) flows over complex terrains containing, e.g. hills, forest, and lakes is of great interest in wind energy applications, as it can help in locating and optimizing the wind farms. Numerical modeling of wind flows using Computational Fluid Dynamics (CFD) has become a popular technique during the last few decades. Due to the inherent flow variability and large-scale unsteadiness typical in ABL flows in general and especially over complex terrains, the flow can be difficult to be predicted accurately enough by using the Reynolds-Averaged Navier-Stokes equations (RANS). Large- Eddy Simulation (LES) resolves the largest and thus most important turbulent eddies and models only the small-scale motions which are more universal than the large eddies and thus easier to model. Therefore, LES is expected to be more suitable for this kind of simulations although it is computationally more expensive than the RANS approach. With the fast development of computers and open-source CFD software during the recent years, the application of LES toward atmospheric flow is becoming increasingly common nowadays. The aim of the work is to simulate atmospheric flows over realistic and complex terrains by means of LES. Evaluation of potential in-land wind park locations will be the main application for these simulations. Development of the LES methodology to simulate the atmospheric flows over realistic terrains is reported in the thesis. The work also aims at validating the LES methodology at a real scale. In the thesis, LES are carried out for flow problems ranging from basic channel flows to real atmospheric flows over one of the most recent real-life complex terrain problems, the Bolund hill. All the simulations reported in the thesis are carried out using a new OpenFOAM® -based LES solver. The solver uses the 4th order time-accurate Runge-Kutta scheme and a fractional step method. Moreover, development of the LES methodology includes special attention to two boundary conditions: the upstream (inflow) and wall boundary conditions. The upstream boundary condition is generated by using the so-called recycling technique, in which the instantaneous flow properties are sampled on aplane downstream of the inlet and mapped back to the inlet at each time step. This technique develops the upstream boundary-layer flow together with the inflow turbulence without using any precursor simulation and thus within a single computational domain. The roughness of the terrain surface is modeled by implementing a new wall function into OpenFOAM® during the thesis work. Both, the recycling method and the newly implemented wall function, are validated for the channel flows at relatively high Reynolds number before applying them to the atmospheric flow applications. After validating the LES model over simple flows, the simulations are carried out for atmospheric boundary-layer flows over two types of hills: first, two-dimensional wind-tunnel hill profiles and second, the Bolund hill located in Roskilde Fjord, Denmark. For the twodimensional wind-tunnel hills, the study focuses on the overall flow behavior as a function of the hill slope. Moreover, the simulations are repeated using another wall function suitable for smooth surfaces, which already existed in OpenFOAM® , in order to study the sensitivity of the flow to the surface roughness in ABL flows. The simulated results obtained using the two wall functions are compared against the wind-tunnel measurements. It is shown that LES using the implemented wall function produces overall satisfactory results on the turbulent flow over the two-dimensional hills. The prediction of the flow separation and reattachment-length for the steeper hill is closer to the measurements than the other numerical studies reported in the past for the same hill geometry. The field measurement campaign performed over the Bolund hill provides the most recent field-experiment dataset for the mean flow and the turbulence properties. A number of research groups have simulated the wind flows over the Bolund hill. Due to the challenging features of the hill such as the almost vertical hill slope, it is considered as an ideal experimental test case for validating micro-scale CFD models for wind energy applications. In this work, the simulated results obtained for two wind directions are compared against the field measurements. It is shown that the present LES can reproduce the complex turbulent wind flow structures over a complicated terrain such as the Bolund hill. Especially, the present LES results show the best prediction of the turbulent kinetic energy with an average error of 24.1%, which is a 43% smaller than any other model results reported in the past for the Bolund case. Finally, the validated LES methodology is demonstrated to simulate the wind flow over the existing Muukko wind farm located in South-Eastern Finland. The simulation is carried out only for one wind direction and the results on the instantaneous and time-averaged wind speeds are briefly reported. The demonstration case is followed by discussions on the practical aspects of LES for the wind resource assessment over a realistic inland wind farm.

Value based pricing and marketing of marine engines

Objective of the thesis is to create a value based pricing model for marine engines and study the feasibility of implementing such model in the sales organization of a specific segment in the case company’s marine division. Different pricing strategies, concept of “value”, and how perceptions of value can be influenced through value based marketing are presented as theoretical background for the value based pricing model. Forbis and Mehta’s Economic Value to Customer (EVC) was selected as framework to create the value based pricing model for marine engines. The EVC model is based on calculating and comparing life-cycle costs of the reference product and competing products, thus showing the quantifiable value of the company’s own product compared to competition. In the applied part of the thesis, the components of the EVC model are identified for a marine diesel engine, the components are explained, and an example calculation created in Excel is presented. When examining the possibilities to implement in practice a value based pricing strategy based on the EVC model, it was found that the lack of precise information on competing products is the single biggest obstacle to use EVC exactly as presented in the literature. It was also found that sometimes necessary communication channels are missing and that there is simply a lack of interest from some clients and product end-users part to spend time on studying the life-cycle costs of the product. Information on the company’s own products is however sufficient and the sales force is capable to communicate to sufficiently high executive levels in the client organizations. Therefore it is suggested to focus on quantifying and communicating the company’s own value proposition. The dynamic nature of the business environment (variance in applications in which engines are installed, different clients, competition, end-clients etc.) means also that each project should be created its own EVC calculation. This is demanding in terms of resources needed, thus it is suggested to concentrate on selected projects and buyers, and to clients where the necessary communication channels to right levels in the customer organization are available. Finally, it should be highlighted that as literature suggests, implementing a value based pricing strategy is not possible unless the whole business approach is value based.

Emission, kinetic and magnetic phenomena in rare-earth and transition metal doped ZnSe single crystals

In this work emission, optical, electrical and magnetic properties of the d- and f- elements doped zinc selenide crystals were investigated within a wide temperature range. Doping was performed in various technological processes: during the growth by chemical vapor transport method; by thermal diffusion from the Bi or Zn melt. Concentration of the doping impurity in the crystals was controlled by amount of the dopant in the source material or by its concentration in the doping media. Special interest in the work was paid to the influence of the different concentrations of Cr and Yb impurities on ZnSe crystals’ properties, correlations between observed effects and similarities with the Ni, Mn and Gd dopants are analysed. Possibility of formation of the excitons bound to the doping d-ions was shown. In contrast to this, it was observed that f-elements do not bound excitons, but prevent formation of excitons bound to some uncontrolled impurities. A mechanism of Cr doping impurity interaction with background impurities and zinc selenide structural defects was proposed based on experimental data. An assumption about resonant energy transfer between double charged chromium ions and complexes based on crystals’ vacancy defects was made. A correlation between emission and magnetic properties of the d- ions doped samples was established. Based on this correlation a mechanism explaining the concentration quench of the emission was proposed. It was found that f-ions bind electrically active shallow and deep donor and acceptor states of background impurity to electrically neutral complexes. This may be observed as “purification” of ZnSe crystals by doping with the rare-earth elements, resulting i tendency of the properties of f-ion doped crystals to the properties of intrinsic crystals, but with smaller concentration of uncontrolled native and impurity defects. A possible interpretation of this effect was proposed. It was shown that selenium substituting impurities decrease efficiency of the Yb doping. Based on this experimental results an attempt to determine ytterbium ion surroundings in the crystal lattice was made. It was shown that co-doping of zinc selenide crystals with the d- and f- ions leads to the combination of the impurities influence on the material’s properties. On the basis of obtained data an interaction mechanism of the d- and f-elements co-dopants was proposed. Guided by the model of the ytterbium ion incorporation in the selenide sublattice of the ZnSe crystals, an assumption about stabilization of single charged chromium ions in the zinc sublattice crystal nodes, by means of formation of the local charge compensating clusters, was made.

The husk fiber of Cocos nucifera L. (Palmae) is a source of anti-neoplastic activity

In the present study, we investigated the in vitro anti-tumoral activities of fractions from aqueous extracts of the husk fiber of the typical A and common varieties of Cocos nucifera (Palmae). Cytotoxicity against leukemia cells was determined by the 3-[4,5-dimethylthiazol-2-yl]-2,5-diphenyltetrazolium bromide (MTT) assay. Cells (2 x 104/well) were incubated with 0, 5, 50 or 500 µg/mL high- or low-molecular weight fractions for 48 h, treated with MTT and absorbance was measured with an ELISA reader. The results showed that both varieties have almost similar antitumoral activity against the leukemia cell line K562 (60.1 ± 8.5 and 47.5 ± 11.9% for the typical A and common varieties, respectively). Separation of the crude extracts with Amicon membranes yielded fractions with molecular weights ranging in size from 1-3 kDa (fraction A) to 3-10 kDa (fraction B) and to more than 10 kDa (fraction C). Cells were treated with 500 µg/mL of these fractions and cytotoxicity was evaluated by MTT. Fractions ranging in molecular weight from 1-10 kDa had higher cytotoxicity. Interestingly, C. nucifera extracts were also active against Lucena 1, a multidrug-resistant leukemia cell line. Their cytotoxicity against this cell line was about 50% (51.9 ± 3.2 and 56.3 ± 2.9 for varieties typical A and common, respectively). Since the common C. nucifera variety is extensively cultured in Brazil and the husk fiber is its industrial by-product, the results obtained in the present study suggest that it might be a very inexpensive source of new antineoplastic and anti-multidrug resistant drugs that warrants further investigation.

Effect of scanner acoustic background noise on strict resting-state fMRI

Functional MRI (fMRI) resting-state experiments are aimed at identifying brain networks that support basal brain function. Although most investigators consider a ‘resting-state’ fMRI experiment with no specific external stimulation, subjects are unavoidably under heavy acoustic noise produced by the equipment. In the present study, we evaluated the influence of auditory input on the resting-state networks (RSNs). Twenty-two healthy subjects were scanned using two similar echo-planar imaging sequences in the same 3T MRI scanner: a default pulse sequence and a reduced “silent” pulse sequence. Experimental sessions consisted of two consecutive 7-min runs with noise conditions (default or silent) counterbalanced across subjects. A self-organizing group independent component analysis was applied to fMRI data in order to recognize the RSNs. The insula, left middle frontal gyrus and right precentral and left inferior parietal lobules showed significant differences in the voxel-wise comparison between RSNs depending on noise condition. In the presence of low-level noise, these areas Granger-cause oscillations in RSNs with cognitive implications (dorsal attention and entorhinal), while during high noise acquisition, these connectivities are reduced or inverted. Applying low noise MR acquisitions in research may allow the detection of subtle differences of the RSNs, with implications in experimental planning for resting-state studies, data analysis, and ergonomic factors.

Monitoring of wine aging process by electrospray ionization mass spectrometry

The characterization of wine samples by direct insertion electrospray ionization mass spectrometry (ESI-MS), without pre-treatment or chromatographic separation, in a process denominated fingerprinting, has been applied to several samples of wine produced with grapes of the Pinot noir, Merlot and Cabernet Sauvignon varieties from the state o Rio Grande do Sul, in Brazil. The ESI-MS fingerprints of the samples detected changes which occurred during the aging process in the three grape varieties. Principal Component Analysis (PCA) of the negative ion mode fingerprints was used to group the samples, pinpoint the main changes in their composition, and indicate marker ions for each group of samples.

Peptide separation of commercial fermented milk during refrigerated storage

Milk is an important source of bioactive compounds. Many of these compounds are released during fermentation and refrigerated storage. The aim of this study was to determine the release of peptides by lactic acid bacteria in commercial fermented milk during refrigerated storage. The size and profile of peptides were analyzed by polyacrylamide gel electrophoresis and sizeexclusion HPLC. During electrophoresis, it was observed that the peptides were released from caseins, whereas β-lactoglobulin was the whey protein with the highest degradation. HPLC analysis confirmed the pattern of peptide formation observed in electrophoresis. Two fractions lower than 2 kDa with aromatic amino acids in their structure were separated. These results were consistent with those reported for structures of peptides with antihypertensive activity. Therefore, the presence of aromatic amino acids in the peptide fractions obtained increases the likelihood of finding peptides with such activity in refrigerated commercial fermented milk. In conclusion, during cold storage, peptides with different molecular weights are released and accumulated. This could be due to the action of proteinases and peptidases of the proteolytic system in lactic acid bacteria.

A social-cognitive model of monitoring and its relationship to behaviour in a naturalistic observation : development and individual differences

years 8 months) and 24 older (M == 7 years 4 months) children. A Monitoring Process Model (MPM) was developed and tested in order to ascertain at which component process ofthe MPM age differences would emerge. The MPM had four components: (1) assessment; (2) evaluation; (3) planning; and (4) behavioural control. The MPM was assessed directly using a referential communication task in which the children were asked to make a series of five Lego buildings (a baseline condition and one building for each MPM component). Children listened to instructions from one experimenter while a second experimenter in the room (a confederate) intetjected varying levels ofverbal feedback in order to assist the children and control the component ofthe MPM. This design allowed us to determine at which "stage" ofprocessing children would most likely have difficulty monitoring themselves in this social-cognitive task. Developmental differences were obselVed for the evaluation, planning and behavioural control components suggesting that older children were able to be more successful with the more explicit metacomponents. Interestingly, however, there was no age difference in terms ofLego task success in the baseline condition suggesting that without the intelVention ofthe confederate younger children monitored the task about as well as older children. This pattern ofresults indicates that the younger children were disrupted by the feedback rather than helped. On the other hand, the older children were able to incorporate the feedback offered by the confederate into a plan ofaction. Another aim ofthis study was to assess similar processing components to those investigated by the MPM Lego task in a more naturalistic observation. Together the use ofthe Lego Task ( a social cognitive task) and the naturalistic social interaction allowed for the appraisal of cross-domain continuities and discontinuities in monitoring behaviours. In this vein, analyses were undertaken in order to ascertain whether or not successful performance in the MPM Lego Task would predict cross-domain competence in the more naturalistic social interchange. Indeed, success in the two latter components ofthe MPM (planning and behavioural control) was related to overall competence in the naturalistic task. However, this cross-domain prediction was not evident for all levels ofthe naturalistic interchange suggesting that the nature ofthe feedback a child receives is an important determinant ofresponse competency. Individual difference measures reflecting the children's general cognitive capacity (Working Memory and Digit Span) and verbal ability (vocabulary) were also taken in an effort to account for more variance in the prediction oftask success. However, these individual difference measures did not serve to enhance the prediction oftask performance in either the Lego Task or the naturalistic task. Similarly, parental responses to questionnaires pertaining to their child's temperament and social experience also failed to increase prediction oftask performance. On-line measures ofthe children's engagement, positive affect and anxiety also failed to predict competence ratings.

Hot cognition and activation of the medial prefrontal cortex: Self-regulating in contexts involving motivational pressures

The medial prefrontal cortex (mPFC) is involved in performance-monitoring and has been implicated in the generation of several electrocortical responses associated with self-regulation. The error-related negativity (ERN), the inhibitory Nogo N2 (N2), and the feedback-related negativity (FRN) are event-related potential (ERP) components which reflect mPFC activity associated with feedback to behavioural (ERN, N2) and environmental (FRN) consequences. Our main goal was to determine whether or not rnPFC activation varies as a function of motivational context (e.g., those involving performance-related incentives) or the use of internally versus externally generated feedback signals (i.e., errors). Additionally, we assessed medial prefrontal activity in relation to individual differences in personality and temperament. Participants completed a combination of tasks in which performance-related incentives were associated with task performance and feedback generated from internal versus external responses. MPFC activity was indexed using both ERP scalp voltage peaks and intracerebral current source density (CSD) of dorsal and ventral regions. Additionally, participants completed several questionnaires assessing personality and temperament styles. Given previous studies have shown that enhanced mPFC activity to loss (or negative) feedback, we expected that activity in the mPFC would generally be greater during the Loss condition relative to the Win condition for both the ERN and N2. Also, due to the evidence that the (vmPFC) is engaged in arousing contexts, we hypothesized that activity in the ventromedial prefrontal cortex (vmPFC) would be greater than activity in the dorsomedial prefrontal cortex (dmPFC), especially in the Loss condition of the GoNogo task (ERN). Similarly, loss feedback in the BART (FRN) was expected to engage the vmPFC more than the dmPFC. Finally, we predicted that persons rating themselves as more willing to engage in approach-related behaviours or to exhibit rigid cognitive styles would show reduced activity of the mPFC. Overall, our results emphasize the role of affective evaluations of behavioural and environmental consequences when self-regulating. Although there were no effects of context on brain activity, our data indicate that, during the time of the ERN and N2 on the MW Go-Nogo task and the FRN on the BART, the vrnPFC was more active compared to the dmPFC. Moreover, regional recruitment in the mPFC was similar across internally (ERN) and externally (FRN) generated errors signals associated with loss feedback, as reflected by relatively greater activity in the vmPFC than the dmPFC. Our data also suggest that greater activity in the mPFC is associated with better inhibitory control, as reflected by both scalp and CSD measures. Additionally, deactivation of the subgenual anterior cingulate cortex (sgACC) and lower levels of self-reported positive affect were both related to increased voluntary risk-taking on the BART. Finally, persons reporting higher levels of approach-related behaviour or cognitive rigidity showed reduced activity of the mPFC. These results are in line with previous research emphasizing that affect/motivation is central to the processes reflected by mediofrontal negativities (MFNs), that the vmPFC is involved in regulating demands on motivational/affective systems, and that the underlying mechanisms driving these functions vary across both individuals and contexts.

REFLECT : logiciel de restitution des réflectances au sol pour l’amélioration de la qualité de l'information extraite des images satellitales à haute résolution spatiale

RÉSUMÉ - Les images satellitales multispectrales, notamment celles à haute résolution spatiale (plus fine que 30 m au sol), représentent une source d’information inestimable pour la prise de décision dans divers domaines liés à la gestion des ressources naturelles, à la préservation de l’environnement ou à l’aménagement et la gestion des centres urbains. Les échelles d’étude peuvent aller du local (résolutions plus fines que 5 m) à des échelles régionales (résolutions plus grossières que 5 m). Ces images caractérisent la variation de la réflectance des objets dans le spectre qui est l’information clé pour un grand nombre d’applications de ces données. Or, les mesures des capteurs satellitaux sont aussi affectées par des facteurs « parasites » liés aux conditions d’éclairement et d’observation, à l’atmosphère, à la topographie et aux propriétés des capteurs. Deux questions nous ont préoccupé dans cette recherche. Quelle est la meilleure approche pour restituer les réflectances au sol à partir des valeurs numériques enregistrées par les capteurs tenant compte des ces facteurs parasites ? Cette restitution est-elle la condition sine qua non pour extraire une information fiable des images en fonction des problématiques propres aux différents domaines d’application des images (cartographie du territoire, monitoring de l’environnement, suivi des changements du paysage, inventaires des ressources, etc.) ? Les recherches effectuées les 30 dernières années ont abouti à une série de techniques de correction des données des effets des facteurs parasites dont certaines permettent de restituer les réflectances au sol. Plusieurs questions sont cependant encore en suspens et d’autres nécessitent des approfondissements afin, d’une part d’améliorer la précision des résultats et d’autre part, de rendre ces techniques plus versatiles en les adaptant à un plus large éventail de conditions d’acquisition des données. Nous pouvons en mentionner quelques unes : - Comment prendre en compte des caractéristiques atmosphériques (notamment des particules d’aérosol) adaptées à des conditions locales et régionales et ne pas se fier à des modèles par défaut qui indiquent des tendances spatiotemporelles à long terme mais s’ajustent mal à des observations instantanées et restreintes spatialement ? - Comment tenir compte des effets de « contamination » du signal provenant de l’objet visé par le capteur par les signaux provenant des objets environnant (effet d’adjacence) ? ce phénomène devient très important pour des images de résolution plus fine que 5 m; - Quels sont les effets des angles de visée des capteurs hors nadir qui sont de plus en plus présents puisqu’ils offrent une meilleure résolution temporelle et la possibilité d’obtenir des couples d’images stéréoscopiques ? - Comment augmenter l’efficacité des techniques de traitement et d’analyse automatique des images multispectrales à des terrains accidentés et montagneux tenant compte des effets multiples du relief topographique sur le signal capté à distance ? D’autre part, malgré les nombreuses démonstrations par des chercheurs que l’information extraite des images satellitales peut être altérée à cause des tous ces facteurs parasites, force est de constater aujourd’hui que les corrections radiométriques demeurent peu utilisées sur une base routinière tel qu’est le cas pour les corrections géométriques. Pour ces dernières, les logiciels commerciaux de télédétection possèdent des algorithmes versatiles, puissants et à la portée des utilisateurs. Les algorithmes des corrections radiométriques, lorsqu’ils sont proposés, demeurent des boîtes noires peu flexibles nécessitant la plupart de temps des utilisateurs experts en la matière. Les objectifs que nous nous sommes fixés dans cette recherche sont les suivants : 1) Développer un logiciel de restitution des réflectances au sol tenant compte des questions posées ci-haut. Ce logiciel devait être suffisamment modulaire pour pouvoir le bonifier, l’améliorer et l’adapter à diverses problématiques d’application d’images satellitales; et 2) Appliquer ce logiciel dans différents contextes (urbain, agricole, forestier) et analyser les résultats obtenus afin d’évaluer le gain en précision de l’information extraite par des images satellitales transformées en images des réflectances au sol et par conséquent la nécessité d’opérer ainsi peu importe la problématique de l’application. Ainsi, à travers cette recherche, nous avons réalisé un outil de restitution de la réflectance au sol (la nouvelle version du logiciel REFLECT). Ce logiciel est basé sur la formulation (et les routines) du code 6S (Seconde Simulation du Signal Satellitaire dans le Spectre Solaire) et sur la méthode des cibles obscures pour l’estimation de l’épaisseur optique des aérosols (aerosol optical depth, AOD), qui est le facteur le plus difficile à corriger. Des améliorations substantielles ont été apportées aux modèles existants. Ces améliorations concernent essentiellement les propriétés des aérosols (intégration d’un modèle plus récent, amélioration de la recherche des cibles obscures pour l’estimation de l’AOD), la prise en compte de l’effet d’adjacence à l’aide d’un modèle de réflexion spéculaire, la prise en compte de la majorité des capteurs multispectraux à haute résolution (Landsat TM et ETM+, tous les HR de SPOT 1 à 5, EO-1 ALI et ASTER) et à très haute résolution (QuickBird et Ikonos) utilisés actuellement et la correction des effets topographiques l’aide d’un modèle qui sépare les composantes directe et diffuse du rayonnement solaire et qui s’adapte également à la canopée forestière. Les travaux de validation ont montré que la restitution de la réflectance au sol par REFLECT se fait avec une précision de l’ordre de ±0.01 unités de réflectance (pour les bandes spectrales du visible, PIR et MIR), même dans le cas d’une surface à topographie variable. Ce logiciel a permis de montrer, à travers des simulations de réflectances apparentes à quel point les facteurs parasites influant les valeurs numériques des images pouvaient modifier le signal utile qui est la réflectance au sol (erreurs de 10 à plus de 50%). REFLECT a également été utilisé pour voir l’importance de l’utilisation des réflectances au sol plutôt que les valeurs numériques brutes pour diverses applications courantes de la télédétection dans les domaines des classifications, du suivi des changements, de l’agriculture et de la foresterie. Dans la majorité des applications (suivi des changements par images multi-dates, utilisation d’indices de végétation, estimation de paramètres biophysiques, …), la correction des images est une opération cruciale pour obtenir des résultats fiables. D’un point de vue informatique, le logiciel REFLECT se présente comme une série de menus simples d’utilisation correspondant aux différentes étapes de saisie des intrants de la scène, calcul des transmittances gazeuses, estimation de l’AOD par la méthode des cibles obscures et enfin, l’application des corrections radiométriques à l’image, notamment par l’option rapide qui permet de traiter une image de 5000 par 5000 pixels en 15 minutes environ. Cette recherche ouvre une série de pistes pour d’autres améliorations des modèles et méthodes liés au domaine des corrections radiométriques, notamment en ce qui concerne l’intégration de la FDRB (fonction de distribution de la réflectance bidirectionnelle) dans la formulation, la prise en compte des nuages translucides à l’aide de la modélisation de la diffusion non sélective et l’automatisation de la méthode des pentes équivalentes proposée pour les corrections topographiques.

Lier les présents aux absents : regards sur la condition d’exilé dans les littératures libano-québécoise et arabe contemporaine

Les paramètres de l’exil, comme déplacement, se transforment aujourd’hui dans un contexte de mondialisation, interrogeant le rôle des nations alors que les sociétés impliquent de plus en plus de mobilité et de diversité culturelle. Cette condition d’exilé aux repères mouvants, inscrite dans une temporalité discontinue et dont l’expérience est toujours douloureuse, a donné lieu à une littérature prolifique dans le domaine des études littéraires au cours du 20e siècle. En quoi le 21e propose-t-il un regard différent sur cette condition ? Dans ce mémoire nous analyserons quatre œuvres contemporaines qui nous proposent différentes variations des transformations identitaires profondes qui caractérisent la condition d’exilé. Deux des grands axes autour desquels s’est articulée la condition d’exilé ont été développés par Edward Said, qui propose une posture critique et politique, et Julia Kristeva, qui présente l’exil comme une condition plutôt psychique. Suivant cette perspective analytique, l’autobiographie de Mourid Barghouti fait écho à la compréhension de l’exil telle que l’entend Said, en pleine autonomie instauratrice. Puis, le roman de Rawi Hage dans une expérience plus psychique de l’exil, plus traumatique et plus violente du vécu avant l’exil, suggère que le rapport avec le milieu environnant a un impact sur l’expérience de l’exil, alors que dans ce cas il reste dysfonctionnel, et qu’un rapport pathologique à l’existence peut ensuite se manifester. Ensuite, le roman d’Abla Farhoud expose la possibilité d’un dépassement de cette expérience pathologique de l’exil par la distance, celle de l’âge et de la prise de parole. Finalement, dans la pièce Incendies de Mouawad, l’expérience psychique de l’exil est dépassée à la fois par une traduction de l’indicible de la violence, par un retour sur les traumas précédant l’exil, et par un travail collectif – comme autres formes de distances. Cette dernière œuvre est donc porteuse d’une compréhension de l’exil impliquant une dimension psychique, tout en devenant critique et politique, telle que le révèlent les écrits de Jacques Rancière. À la lumière de ces analyses, la condition d’exilé réclame d’urgence un retour sur les traumas précédents, le trauma qu’est l’exil, afin qu’une autonomie, une créativité et un engagement s’en dégagent, dans une société, dans un monde plus grand que soi. Pour les trois derniers auteurs, c’est la société québécoise qui révèle à la fois une compréhension des problématiques majeures de la condition d’exilé et une ouverture face à celles-ci, en ce début de 21e siècle.

Contribution des régions fronto-striatales dans les fonctions exécutives

Des études récentes ont montré que le noyau caudé interagissait avec le cortex préfrontal et qu’il pourrait être impliqué dans les fonctions exécutives. Le but de cette thèse était d’étudier la contribution du noyau caudé dans les fonctions exécutives, plus précisément dans des tâches de monitoring et de changement de règle, et d’observer comment ces régions fronto-striatales interagissent avec le réseau par défaut (RPD). Dans un premier temps, nous avons étudié le rôle du noyau caudé dans les deux types de monitoring : le monitoring d’origine interne, consistant à effectuer un suivi sur l’état de l’information en mémoire de travail afin de pouvoir faire un choix subséquent, et dans le monitoring d’origine externe où le suivi sur l’état des items est effectué par l’individu, mais la sélection est exécutée par une source externe. Il a été montré que le cortex préfrontal dorsolatéral (CPFDL) est impliqué dans les deux types de monitoring. À l’aide de l’imagerie par résonance magnétique fonctionnelle (IRMf), nos résultats ont montré une augmentation significative du signal BOLD au niveau du CPFDL dans les contrastes des conditions de monitoring d’origine interne et monitoring d’origine externe par rapport à la condition contrôle. De manière plus importante, une augmentation significative de l’activité a été observée dans le noyau caudé seulement dans les soustractions impliquant le monitoring d’origine interne par rapport à la condition contrôle, et par rapport à la condition de monitoring d’origine externe. En deuxième lieu, des études ont montré une contribution spécifique des régions fronto-striatales dans l’exécution d’un changement de règle. Toutefois, l’effet d’un changement de règle sur l’activité cérébrale n’a jamais été étudié sur les essais subséquents. À l’aide de l’IRMf, le cortex préfrontal ventrolatéral (CPFVL) et le noyau caudé ont montré une augmentation significative de leur activité lors des changements de règle continus et lors des changements de règles sporadiques par rapport à la condition contrôle, et aussi lors des essais où le maintien d’une même règle devait être effectué pour une courte durée par opposition au contrôle. Cependant, aucune activité fronto-striatale n’a été observée lorsqu’une même règle devait être appliquée pour une plus longue période. De plus, une diminution significative de l’activité du noyau caudé a été observée lors de la répétition de l’exécution d’une même règle suggérant une meilleure intégration de cette dernière. Finalement, plusieurs études ont montré une déactivation du RPD lors de l’exécution de tâches. À l’aide de l’IRMf, nous avons posé l’hypothèse que le RPD serait corrélé négativement avec les régions fronto-striatales lors de l’exécution d’une tâche de changement de règle. Nos résultats montrent une augmentation significative de l’activité des régions fronto-striatales lors d’une augmentation du nombre d’essais de changement de règle consécutif, pendant que le RPD montre une déactivation continue. De façon intéressante, pendant que les régions fronto-striatales montrent une diminution de leur activité lors de l’exécution d’une même règle pour une longue période, le RPD augmente son activité de façon significative. On conclut donc que le noyau caudé joue un rôle important dans la planification d’une nouvelle action lorsque plusieurs possibilités doivent être considérées en mémoire de travail, et ce en même temps. Finalement, le RPD montre une corrélation négative avec les régions fronto-striatales suggérant sa participation dans l’intégration d’une tâche devenant de plus en plus familière.