A geometric study of liquid retention in open-cell metal foams

Open-cell metal foams show promise as an emerging novel material for heat exchanger applications. The high surface-area-to-volume ratio suggests increased compactness and decrease in weight of heat exchanger designs. However, the metal foam structure appears conducive to condensate retention, which would degenerate heat transfer performance. This research investigates the condensate retention behavior of aluminum open-cell metal foams through the use of static dip tests and geometrical classification via X-ray Micro-Computed Tomography. Aluminum open-cell metal foam samples of 5, 10, 20, and 40 pores per inch (PPI), all having a void fraction greater than 90%, were included in this investigation. In order to model the condensate retention behavior of metal foams, a clearer understanding of the geometry was required. After exploring the ideal geometries presented in the open literature, X-ray Micro-Computed Tomography was employed to classify the actual geometry of the metal foam samples. The images obtained were analyzed using specialized software from which geometric information including strut length and pore shapes were extracted. The results discerned a high variability in ligament length, as well as features supporting the ideal geometry known as the Weaire-Phelan unit cell. The static dip tests consisted of submerging the metal foam samples in a liquid, then allowing gravity-induced drainage until steady-state was reached and the liquid remaining in the metal foam sample was measured. Three different liquids, water, ethylene glycol, and 91% isopropyl alcohol, were employed. The behaviors of untreated samples were compared to samples subjected to a Beomite surface treatment process, and no significant differences in retention behavior were discovered. The dip test results revealed two distinct regions of condensate retention, each holding approximately half of the total liquid retained by the sample. As expected, condensate retention increased as the pores sizes decreased. A model based on surface tension was developed to predict the condensate retention in the metal foam samples and verified using a regular mesh. Applying the model to both the ideal and actual metal foam geometries showed good agreement with the dip test results in this study.

Madeira wine vinification process: analysis and control

The present study was done in collaboration with J. Faria e Filhos company, a Madeira wine producer, and its main goal was to fully characterize three wines produced during 2014 harvest and identify possible improving points in the winemaking process. The winemaking process was followed during 4 weeks, being registered the amounts of grapes received, the fermentation temperatures, the time at which fermentation was stopped and evolution of must densities until the fortification time. The characterization of musts and wines was done in terms of density, total and volatile acidity, alcohol content, pH, total of polyphenol, organic acids composition, sugars concentration and the volatile profile. Also, it was developed and validated an analytical methodology to quantify the volatile fatty acids, namely using SPME-GC-MS. Briefly, the following key features were obtained for the latter methodology: linearity (R2=0.999) e high sensitivity (LOD =0.026-0.068 mg/L), suitable precision (repeatability and reproducibility lower than 8,5%) and good recoveries (103,11-119,46%). The results reveal that fermentation temperatures should be controlled in a more strictly manner, in order to ensure a better balance in proportion of some volatile compounds, namely the esters and higher alcohols and to minimize the concentration of some volatiles, namely hexanoic, octanoic and decanoic acids, that when above their odours threshold are not positive for the wine aroma. Also, regarding the moment to stop the fermentation, it was verified that it can be introduced changes which can also be benefit to guarantee the tipicity of Madeira wine bouquet.

GERMINAÇÃO DE SEMENTES DE Piptadenia moniliformis Benth. SOB ESTRESSE HÍDRICO

O período de germinação e o estabelecimento de plântulas é um dos fatores mais importantes para a sobrevivência das espécies, principalmente nos locais em que a disponibilidade de água é limitada, como na região da Caatinga. Neste sentido, o objetivo deste trabalho foi avaliar o efeito do estresse hídrico sobre a germinação de sementes de Piptadenia moniliformis Benth. Foram utilizados três lotes (L1, L2 e L3), correspondentes aos anos de produção de 2006, 2007 e 2008, respectivamente. Antes do teste de germinação, as sementes foram escarificadas com ácido sulfúrico concentrado durante 30 minutos. Para induzir o deficit hídrico, foi utilizado o polietileno glicol (PEG 6000), nos seguintes potenciais osmóticos: - 0,3; -0,6; -0,9, -1,2 e -1,5 MPa e a água (0 MPa) sob as temperaturas de 25 e 30ºC. As características avaliadas foram: porcentagem de germinação e de plântulas normais, índice de velocidade de germinação e massa seca de plântulas. O processo germinativo de sementes de Piptadenia moniliformis Benth. é comprometido a partir de potenciais hídricos inferiores a -0,6 MPa a 25 e 30 °C; potenciais hídricos iguais ou inferiores a -1,2 MPa inibem a formação de plântulas normais nas duas temperaturas; a tolerância ao estresse hídrico simulado com PEG 6000 é variável entre lotes de sementes e temperaturas de germinação.

Adsorção de corantes têxteis aniônicos e catiônicos em resíduos do processamento de fios de algodão modificados quimicamente

The textile industry generates a large volume of high organic effluent loading whoseintense color arises from residual dyes. Due to the environmental implications caused by this category of contaminant there is a permanent search for methods to remove these compounds from industrial waste waters. The adsorption alternative is one of the most efficient ways for such a purpose of sequestering/remediation and the use of inexpensive materials such as agricultural residues (e.g., sugarcane bagasse) and cotton dust waste (CDW) from weaving in their natural or chemically modified forms. The inclusion of quaternary amino groups (DEAE+) and methylcarboxylic (CM-) in the CDW cellulosic structure generates an ion exchange capacity in these formerly inert matrix and, consequently, consolidates its ability for electrovalent adsorption of residual textile dyes. The obtained ionic matrices were evaluated for pHpcz, the retention efficiency for various textile dyes in different experimental conditions, such as initial concentration , temperature, contact time in order to determine the kinetic and thermodynamic parameters of adsorption in batch, turning comprehensive how does occur the process, then understood from the respective isotherms. It was observed a change in the pHpcz for CM--CDW (6.07) and DEAE+-CDW (9.66) as compared to the native CDW (6.46), confirming changes in the total surface charge. The ionized matrices were effective for removing all evaluated pure or residual textile dyes under various tested experimental conditions. The kinetics of the adsorption process data had best fitted to the model a pseudosecond order and an intraparticle diffusion model suggested that the process takes place in more than one step. The time required for the system to reach equilibrium varied according to the initial concentration of dye, being faster in diluted solutions. The isotherm model of Langmuir was the best fit to the experimental data. The maximum adsorption capacity varied differently for each tested dye and it is closely related to the interaction adsorbent/adsorbate and dye chemical structure. Few dyes obtained a linear variation of the balance ka constant due to the inversion of temperature and might have influence form their thermodynamic behavior. Dyes that could be evaluated such as BR 18: 1 and AzL, showed features of an endothermic adsorption process (ΔH° positive) and the dye VmL presented exothermic process characteristics (ΔH° negative). ΔG° values suggested that adsorption occurred spontaneously, except for the BY 28 dye, and the values of ΔH° indicated that adsorption occurred by a chemisorption process. The reduction of 31 to 51% in the biodegradability of the matrix after the dye adsorption means that they must go through a cleaning process before being discarded or recycled, and the regeneration test indicates that matrices can be reused up to five times without loss of performance. The DEAE+-CDW matrix was efficient for the removal of color from a real textile effluent reaching an UV-Visible spectral area decrease of 93% when applied in a proportion of 15 g ion exchanger matrix L-1 of colored wastewater, even in the case of the parallel presence of 50 g L-1 of mordant salts in the waste water. The wide range of colored matter removal by the synthesized matrices varied from 40.27 to 98.65 mg g-1 of ionized matrix, obviously depending in each particular chemical structure of the dye upon adsorption.

Investigating the use of LiDAR scanning as a method for the measurement of timber distortion features

Measuring the extent to which a piece of structural timber has distorted at a macroscopic scale is fundamental to assessing its viability as a structural component. From the sawmill to the construction site, as structural timber dries, distortion can render it unsuitable for its intended purposes. This rejection of unusable timber is a considerable source of waste to the timber industry and the wider construction sector. As such, ensuring accurate measurement of distortion is a key step in addressing ineffciencies within timber processing. Currently, the FRITS frame method is the established approach used to gain an understanding of timber surface profile. The method, while reliable, is dependent upon relatively few measurements taken across a limited area of the overall surface, with a great deal of interpolation required. Further, the process is unavoidably slow and cumbersome, the immobile scanning equipment limiting where and when measurements can be taken and constricting the process as a whole. This thesis seeks to introduce LiDAR scanning as a new, alternative approach to distortion feature measurement. In its infancy as a measurement technique within timber research, the practicalities of using LiDAR scanning as a measurement method are herein demonstrated, exploiting many of the advantages the technology has over current approaches. LiDAR scanning creates a much more comprehensive image of a timber surface, generating input data multiple magnitudes larger than that of the FRITS frame. Set-up and scanning time for LiDAR is also much quicker and more flexible than existing methods. With LiDAR scanning the measurement process is freed from many of the constraints of the FRITS frame and can be done in almost any environment. For this thesis, surface scans were carried out on seven Sitka spruce samples of dimensions 48.5x102x3000mm using both the FRITS frame and LiDAR scanner. The samples used presented marked levels of distortion and were relatively free from knots. A computational measurement model was created to extract feature measurements from the raw LiDAR data, enabling an assessment of each piece of timber to be carried out in accordance with existing standards. Assessment of distortion features focused primarily on the measurement of twist due to its strong prevalence in spruce and the considerable concern it generates within the construction industry. Additional measurements of surface inclination and bow were also made with each method to further establish LiDAR's credentials as a viable alternative. Overall, feature measurements as generated by the new LiDAR method compared well with those of the established FRITS method. From these investigations recommendations were made to address inadequacies within existing measurement standards, namely their reliance on generalised and interpretative descriptions of distortion. The potential for further uses of LiDAR scanning within timber researches was also discussed.

THERMAL VACUUM TEST CORRELATION OF A ZERO PROPELLANT LOAD CASE THERMAL CAPACITANCE PROPELLANT GAUGING ANALYTICAL MODEL

This thesis describes the development and correlation of a thermal model that forms the foundation of a thermal capacitance spacecraft propellant load estimator. Specific details of creating the thermal model for the diaphragm propellant tank used on NASA’s Magnetospheric Multiscale spacecraft using ANSYS and the correlation process implemented are presented. The thermal model was correlated to within +/- 3 Celsius of the thermal vacuum test data, and was determined sufficient to make future propellant predictions on MMS. The model was also found to be relatively sensitive to uncertainties in applied heat flux and mass knowledge of the tank. More work is needed to improve temperature predictions in the upper hemisphere of the propellant tank where predictions were found to be 2-2.5 Celsius lower than the test data. A road map for applying the model to predict propellant loads on the actual MMS spacecraft in 2017-2018 is also presented.

Optimization of flocculation process and continuous filtration for sea water primary treatment filtration to reduce SDI for entree to reverse osmosis system

Today , Providing drinking water and process water is one of the major problems in most countries ; the surface water often need to be treated to achieve necessary quality, and in this way, technological and also financial difficulties cause great restrictions in operating the treatment units. Although water supply by simple and cheap systems has been one of the important objectives in most scientific and research centers in the world, still a great percent of population in developing countries, especially in rural areas, don't benefit well quality water. One of the big and available sources for providing acceptable water is sea water. There are two ways to treat sea water first evaporation and second reverse osmosis system. Nowadays R.O system has been used for desalination because of low budget price and easily to operate and maintenance. The sea water should be pretreated before R.O plants, because there is some difficulties in raw sea water that can decrease yield point of membranes in R.O system. The subject of this research may be useful in this way, and we hope to be able to achieve complete success in design and construction of useful pretreatment systems for R.O plant. One of the most important units in the sea water pretreatment plant is filtration, the conventional method for filtration is pressurized sand filters, and the subject of this research is about new filtration which is called continuous back wash sand filtration (CBWSF). The CBWSF designed and tested in this research may be used more economically with less difficulty. It consists two main parts first shell body and second central part comprising of airlift pump, raw water feeding pipe, air supply hose, backwash chamber and sand washer as well as inlet and outlet connections. The CBWSF is a continuously operating filter, i.e. the filter does not have to be taken out of operation for backwashing or cleaning. Inlet water is fed through the sand bed while the sand bed is moving downwards. The water gets filtered while the sand becomes dirty. Simultaneously, the dirty sand is cleaned in the sand washer and the suspended solids are discharged in backwash water. We analyze the behavior of CBWSF in pretreatment of sea water instead of pressurized sand filter. There is one important factor which is not suitable for R.O membranes, it is bio-fouling. This factor is defined by Silt Density Index (SDI).measured by SDI. In this research has been focused on decreasing of SDI and NTU. Based on this goal, the prototype of pretreatment had been designed and manufactured to test. The system design was done mainly by using the design fundamentals of CBWSF. The automatic backwash sand filter can be used in small and also big water supply schemes. In big water treatment plants, the units of filters perform the filtration and backwash stages separately, and in small treatment plants, the unit is usually compacted to achieve less energy consumption. The analysis of the system showed that it may be used feasibly for water treating, especially for limited population. The construction is rapid, simple and economic, and its performance is high enough because no mobile mechanical part is used in it, so it may be proposed as an effective method to improve the water quality and consequently the hygiene level in the remote places of the country.

Air Entrainment in the Turbulent Ship Hull Boundary Layer

Turbulent fluctuations in the vicinity of the water free surface along a flat, vertically oriented surface-piercing plate are studied experimentally using a laboratory-scale experiment. In this experiment, a meter-wide stainless steel belt travels horizontally in a loop around two rollers with vertically oriented axes, which are separated by 7.5 meters. This belt device is mounted inside a large water tank with the water level set just below the top edge of the belt. The belt, rollers, and supporting frame are contained within a sheet metal box to keep the device dry except for one 6-meter-long straight test section between rollers. The belt is launched from rest with an acceleration of up to 3-g in order to quickly reach steady state velocity. This creates a temporally evolving boundary layer analogous to the spatially evolving boundary layer created along a flat-sided ship moving at the same velocity, with a length equivalent to the length of belt that has passed the measurement region since the belt motion began. Surface profile measurements in planes normal to the belt surface are conducted using cinematic Laser Induced Fluorescence and quantitative surface profiles are extracted at each instant in time. Using these measurements, free surface fluctuations are examined and the propagation behavior of these free surface ripples is studied. It is found that free surface fluctuations are generated in a region close to the belt surface, where sub-surface velocity fluctuations influence the behavior of these free surface features. These rapidly-changing surface features close to the belt appear to lead to the generation of freely-propagating waves far from the belt, outside the influence of the boundary layer. Sub-surface PIV measurements are performed in order to study the modification of the boundary layer flow field due to the effects of the water free surface. Cinematic planar PIV measurements are performed in horizontal planes parallel to the free surface by imaging the flow from underneath the tank, providing streamwise and wall-normal velocity fields. Additional planar PIV experiments are performed in vertical planes parallel to the belt surface in order to study the bahvior of streamwise and vertical velocity fields. It is found that the boundary layer grows rapidly near the free surface, leading to an overall thicker boundary layer close to the surface. This rapid boundary layer growth appears to be linked to a process of free surface bursting, the sudden onset of free surface fluctuations. Cinematic white light movies are recorded from beneath the water surface in order to determine the onset location of air entrainment. In addition, qualitative observations of these processes are made in order to determine the mechanisms leading to air entrainment present in this flow.

Processamento e análise de imagens na caracterização da superfície do titânio submetido a um ensaio de cultura de células

This work aims to develop a methodology for analysis of images using overlapping, which assists in identification of microstructural features in areas of titanium, which may be associated with its biological response. That way, surfaces of titanium heat treated for 08 (eight) different ways have been subjected to a test culture of cells. It was a relationship between the grain, texture and shape of grains of surface of titanium (attacked) trying to relate to the process of proliferation and adhesion. We used an open source software for cell counting adhered to the surface of titanium. The juxtaposition of images before and after cell culture was obtained with the aid of micro-hardness of impressions made on the surface of samples. From this image where there is overlap, it is possible to study a possible relationship between cell growth with microstructural characteristics of the surface of titanium. This methodology was efficient to describe a set of procedures that are useful in the analysis of surfaces of titanium subjected to a culture of cells

Maintenance or loss of dialect Andalusian features: Internal and external factors

In the last sixty years a steadily maintained process of convergence towards the Castilian national standard has been occurring in Southern Spain affecting urban middle-class speakers’ varieties, particularly phonology and lexis. As a consequence, unmarked features characterising innovative southern pronunciation have become less frequent and, at the same time, certain standard marked features have been adapted to the southern phonemic inventory. Then, urban middle-class varieties have progressively been stretching out the distance separating them from working-class and rural varieties, and bringing them closer to central Castilian varieties. Intermediate, yet incipient koineised varieties have been described including also transitional Murcia and Extremadura dialects (Hernández & Villena 2009, Villena, Vida & von Essen 2015). (1) Some of the standard phonologically marked features have spread out among southern speakers exclusively based on their mainstream social prestige and producing not only changes in obstruent phoneme inventory –i.e. acquisition of /s/ vs. /θ/ contrast, but also standstill and even reversion of old consonant push- or pull-chain shifts –e.g. /h/ or /d/ fortition, affricate /ʧ/, etc. as well as traditional lexis shift (Villena et al. 2016). Internal (grammar and word frequency) and external (stratification, network and style) factors constraining those features follow similar patterns in the Andalusian speech communities analysed so far (Granada, Malaga) but when we zoom in on central varieties, which are closer to the national standard and then more conservative, differences in frequency increase and conflict sites emerge. (2) Unmarked ‘natural’ phonological features characterising southern dialects, particularly deletion of syllable-final consonant, do not keep pace with this trend of convergence towards the standard. Thus a combination of southern innovative syllable-final and standard conservative onset-consonant features coexist. (3). The main idea is that this intermediate variety is formed through changes suggesting that Andalusian speakers look for the best way of accepting marked prestige features without altering coherence within their inventory. Either reorganisation of the innovative phonemic system in such a way that it may include Castilian and standard /s/ vs. /θ/ contrast or re-syllabification of aspirated /s/ before dental stop are excellent examples of how and why linguistic features are able to integrate intermediate varieties between the dialect-standard continuum.

Some features of the law and order model in Spain

This research is based on the hypothesis that law and order model is displacing the procedura justice system in Spain. After a thorough review of the international literature, one can observe that the traditional structure of the penal system does not seem to be capable of containing the new forms of crime. The new penal model assumes that public opinion is alarmed and unwilling to understand rational approaches to crime, so it will be likely to accept measures aimed at calming the fear of crime, through extensive control policies and penal tools to manage uncivil behavior. Objectives and methodology A measuring instrument has been developed to confirm this hypothesis, consisting of ten features that characterize the law and order model. This instrument has been used to identify examples of its ten features in the rules and practices developed at each phase of the Spanish criminal justice system. The analysis has focused specifically on public discourse about delinquency, criminal policy decisions, legislative processes, police routines, judicial dynamics, and prison system practices. Main results The investigation has shown that there are many processes and practices indicating that the law and order model is consolidating itself in the Spanish penal system. Nevertheless this process has a different intensity at each phase, being stronger at the legislative stage and softer in the penitentiary enforcement phase. One of the main conclusions is, therefore, that the designed instrument is ideal for measuring the degree of penetration of the model throughout the system. Some of the most striking results of the reasearch will be presented at the conference. Finally, proposals arise that could prevent the new model is fully seated in our criminal justice system, finding that the trend toward more severe penalties shown already unsustainable.

Characteristics of Clostridium difficile infection in patients with discordant diagnostic test results

Background: Clinical features of Clostridium difficile infection (CDI) cases diagnosed by detection of polymerase chain reaction (PCR), with negative toxin enzyme immunoassay results (EIA) have not been fully elucidated. The purpose of this study was to determine the magnitude of CDI patients who had negative EIA toxin determinations but positive PCR tests, and their differences in clinical presentation. Methods: We performed a retrospective study comparing the clinical features of CDI cases detected by EIA (toxins A + B) with cases detected by PCR (toxin negative, PCR positive) over a 16-month period. Only patients with an initial Clostridium difficile infection episode that fulfilled a standardized definition were included. Results: During the study period, 107 episodes of CDI were detected. Seventy-four patients (69%) had positive glutamate dehydrogenase (GDH) antigen and EIA determinations (EIA positive patients). Thirty-three patients (31%) had GDH positive, negative toxin EIA and positive PCR determination (PCR positive patients). PCR positive patients were younger, 57 (27) years (mean [SD]), than EIA positive patients, 71 (16) years, (p < 0.001). Fewer PCR positive patients were receiving proton pump inhibitors (21 patients, 64%) than EIA positive patients (61 patients, 82%, p = 0.034). The clinical presentation was similar in both groups. In the multivariate analysis, lower age was identified as the only independent variable associated with PCR positive patients. Conclusions: One third of Clostridium difficile infection patients present negative toxin EIA and PCR positive tests. Performing PCR determination after the negative EIA test is more relevant in younger patients.

Hybrid materials based on polyethylene and MCM-41 microparticles functionalized with silanes: catalytic aspects of in situ polymerization, crystalline features and mechanical properties

New nanocomposites based on polyethylene have been prepared by in situ polymerization of ethylene in presence of mesoporous MCM-41. The polymerization reactions were performed using a zirconocene catalyst either under homogenous conditions or supported onto mesoporous MCM-41 particles, which are synthesized and decorated post-synthesis with two silanes before polymerization in order to promote an enhanced interfacial adhesion. The existence of polyethylene chains able to crystallize within the mesoporous channels in the resulting nanocomposites is figured out from the small endothermic process, located at around 80 C, on heating calorimetric experiments, in addition to the main melting endotherm. These results indicate that polyethylene macrochains can grow up during polymerization either outside or inside the MCM-41 channels, these keeping their regular hexagonal arrangements. Mechanical response is observed to be dependent on the content in mesoporous MCM-41 and on the crystalline features of polyethylene. Accordingly, stiffness increases and deformability decreases in the nanocomposites as much as MCM-41 content is enlarged and polyethylene amount within channels is raised. Ultimate mechanical performance improves with MCM-41 incorporation without varying the final processing temperature.

An Examination of Psychological Meaningfulness, Safety, and Availability as the Underlying Mechanisms linking Job Features and Personal Characteristics to Work Engagement

The present study tested a nomological net of work engagement that was derived from its extant research. Two of the main work engagement models that have been presented and empirically tested in the literature, the JD-R model and Kahn’s model, were integrated to test the effects that job features and personal characteristics can have on work engagement through the psychological conditions of meaningfulness, safety, and availability. In this study, safety refers to psychological perceptions of safety and not workplace safety behaviors. The job features that were tested in this model included person-job fit, autonomy, co-worker relations, supervisor support, procedural justice, and interactional justice, while the personal characteristics consisted of self-consciousness, self-efficacy, extraversion, and neuroticism. Thirty-four hypotheses and a conceptual model were tested in order to establish the viability of this nomological net of work engagement in which it was expected that meaningfulness would mediate the relationships between job features and work engagement, safety would mediate the relationships that job features and personal characteristics have with work engagement, and availability (physical, emotional, and cognitive resources) would mediate the relationships that personal characteristics have with work engagement. Furthermore, analyses were run in order to determine the factor structure of work engagement, assess whether or not it exhibits differential validity from organizational commitment and job satisfaction, and confirm that it is positively related to the outcome variable of organizational citizenship behavior (OCB). The final sample consisted of 500 workers from an online labor market who responded to a questionnaire composed of measures of all constructs included in this study. Findings show that work engagement is best represented as a three-factor construct, composed of vigor, dedication and absorption. Furthermore, support was found for the distinction of work engagement from the related constructs of organizational commitment and job satisfaction. With regard to the proposed model, meaningfulness proved to be the strongest predictor of work engagement. Results show that it partially mediates the relationships that all job features have with work engagement. Safety proved to be a partial mediator of the relationships that autonomy, co-worker relations, supervisor support, procedural justice, interactional justice, and self-efficacy have with work engagement, and fully mediate the relationship between neuroticism and work engagement. Findings also show that availability partially mediates the positive relationships that extraversion and self-efficacy have with work engagement, and fully mediates the negative relationship that neuroticism has with work engagement. Finally, a positive relationship was found between work engagement and OCB. Research and organizational implications are discussed.

Ensemble Stream Model for Data-Cleaning in Sensor Networks

Ensemble Stream Modeling and Data-cleaning are sensor information processing systems have different training and testing methods by which their goals are cross-validated. This research examines a mechanism, which seeks to extract novel patterns by generating ensembles from data. The main goal of label-less stream processing is to process the sensed events to eliminate the noises that are uncorrelated, and choose the most likely model without over fitting thus obtaining higher model confidence. Higher quality streams can be realized by combining many short streams into an ensemble which has the desired quality. The framework for the investigation is an existing data mining tool. First, to accommodate feature extraction such as a bush or natural forest-fire event we make an assumption of the burnt area (BA*), sensed ground truth as our target variable obtained from logs. Even though this is an obvious model choice the results are disappointing. The reasons for this are two: One, the histogram of fire activity is highly skewed. Two, the measured sensor parameters are highly correlated. Since using non descriptive features does not yield good results, we resort to temporal features. By doing so we carefully eliminate the averaging effects; the resulting histogram is more satisfactory and conceptual knowledge is learned from sensor streams. Second is the process of feature induction by cross-validating attributes with single or multi-target variables to minimize training error. We use F-measure score, which combines precision and accuracy to determine the false alarm rate of fire events. The multi-target data-cleaning trees use information purity of the target leaf-nodes to learn higher order features. A sensitive variance measure such as f-test is performed during each node’s split to select the best attribute. Ensemble stream model approach proved to improve when using complicated features with a simpler tree classifier. The ensemble framework for data-cleaning and the enhancements to quantify quality of fitness (30% spatial, 10% temporal, and 90% mobility reduction) of sensor led to the formation of streams for sensor-enabled applications. Which further motivates the novelty of stream quality labeling and its importance in solving vast amounts of real-time mobile streams generated today.