Magnetic non-destructive evaluation of ruptures of tensile armor in oil risers

Risers are flexible multilayered pipes formed by an inner flexible metal structure surrounded by polymer layers and spiral wound steel ligaments, also known as armor wires. Since these risers are used to link subsea pipelines to floating oil and gas production installations, and their failure could produce catastrophic consequences, some methods have been proposed to monitor the armor integrity. However, until now there is no practical method that allows the automatic non-destructive detection of individual armor wire rupture. In this work we show a method using magnetic Barkhausen noise that has shown high efficiency in the detection of armor wire rupture. The results are examined under the cyclic and static load conditions of the riser. This work also analyzes the theory behind the singular dependence of the magnetic Barkhausen noise on the applied tension in riser armor wires.

Positive Affection Measurement: Subjective Well-Being in Married People

The study analyzed the correlations among the different factors of subjective well-being (SWB) using a sample of 106 married people with an average of 16.11 years of marriage. The following instruments were used: Sociodemographic Questionnaire, Socioeconomic Questionnaire, and Subjective Well-being Scale (SWBS). Data analyses were conducted using the Software R and a multivariate model to understand the correlations among the factors of the SWBS. All factors of the SWBS were significantly inter-correlated, which confirm the results of the scale validation study. Future studies are necessary to evaluate the SWB in couples (dyads), which can help to understand whether this concept is influenced by the spouse or only by the marital status.

Quantum oscillations of spin polarization in a GaAs/AlGaAs double quantum well

5 We employ the circular-polarization-resolved magnetophotoluminescence technique to probe the spin character of electron and hole states in a GaAs/AlGaAs strongly coupled double-quantum-well system. The photoluminescence (PL) intensities of the lines associated with symmetric and antisymmetric electron states present clear out-of-phase oscillations between integer values of the filling factor. and are caused by magnetic-field-induced changes in the population of occupied Landau levels near to the Fermi level of the system. Moreover, the degree of circular polarization of these emissions also exhibits the oscillatory behavior with increasing magnetic field. Both quantum oscillations observed in the PL intensities and in the degree of polarizations may be understood in terms of a simple single-particle approach model. The k . p method was used to calculate the photoluminescence peak energies and the degree of circular polarizations in the double-quantum-well structure as a function of the magnetic field. These calculations prove that the character of valence band states plays an important role in the determination of the degree of circular polarization and, thus, resulting in a magnetic-field-induced change of the polarization sign.

Deformation of Implant Abutments After Framework Connection Using Strain Gauges

When a cylinder is connected to an abutment it is expected that abutment and cylinder will be subjected to compression forces throughout their periphery because of the clamping force exerted by the screw. The deformation resultant of this compression should be measurable and uniform along the periphery of the abutment. Considering that multiple retainers connected to each other can affect the fit of a framework, as well as the use of different alloys, it is expected that the abutments will present different levels of deformation as a result of framework connection. The aim of this study was to evaluate the deformation of implant abutments after frameworks, cast either in cobalt-chromium (CoCr) or silver-palladium (AgPd) alloys, were connected. Samples (n = 5) simulating a typical mandibular cantilevered implant-supported prosthesis framework were fabricated in cobalt-chromium and silver-palladium alloys and screwed onto standard abutments positioned on a master-cast containing 5 implant replicas. Two linear strain gauges were fixed on the mesial and distal aspects of each abutment to capture deformation as the retention screws were tightened. A combination of compressive and tensile forces was observed on the abutments for both CoCr and AgPd frameworks. There was no evidence of significant differences in median abutment deformation levels for 9 of the 10 abutment aspects. Visually well-fit frameworks do not necessarily transmit load uniformly to abutments. The use of CoCr alloy for implant-supported prostheses frameworks may be as clinically acceptable as AgPd alloy.

Correlates of change in self-perceived oral health among older adults in Brazil Findings from the Health, Well-Being and Aging Study

Background. Identifying changes in the oral health status of older populations, and their predictors and explanations, is necessary for public health planning. The authors assessed patterns of change in oral health-related quality of life in a large cohort of older adults in Brazil during a five-year period and evaluated associations between baseline characteristics and those changes. Methods. The sample consisted of 747 older people enrolled in a Brazilian cohort study called the Health, Well-Being and Aging (Saude, Bem-estar e Envelhecimento [SABE]) Study. Trained examiners measured participants' self-perceived oral health by using the General Oral Health Assessment Index (GOHAI). The authors calculated changes in the overall GOHAI score and in the scores for each of the GOHAI's three dimensions individually by subtracting the baseline score from the score at follow-up. A positive difference indicated improvement in oral health, a negative difference indicated a decline and a difference of zero indicated no change. Results. The authors found that 48.56 percent of the participants experienced a decline in oral health and 33.48 percent experienced an improvement. Participants with 16 or more missing teeth and eight or more years of education were more likely to have an improvement in total GOHAI score. Deterioration was more likely to occur among those with two or more diseases. Improvement and decline in GOHAI functional scores were related to the number of missing teeth. The authors found no significant model for the change in the psychosocial score, and Self-rated general health was the only variable related to both improvement and decline in pain or discomfort scores. Conclusions. The authors observed a bidirectional change in self-perceived oral health, with deterioration predominating. The strongest predictor of improvement in the total GOHAI score was the number of missing teeth, whereas the number of diseases was the strongest predictor of deterioration. Clinical Implications. Dental professionals and policymakers need to know the directions of change in older adults' oral health to establish treatment priorities and evaluate the impact of services directed at this population.

Magneto-optical probe of quantum Hall states in a wide parabolic well modulated by random potential

Polarized photoluminescence from weakly coupled random multiple well quasi-three-dimensional electron system is studied in the regime of the integer quantum Hall effect. Two quantum Hall ferromagnetic ground states assigned to the uncorrelated miniband quantum Hall state and to the spontaneous interwell phase coherent dimer quantum Hall state are observed. Photoluminescence associated with these states exhibits features caused by finite-size skyrmions: dramatic reduction of the electron spin polarization when the magnetic field is increased past the filling factor nu = 1. The effective skyrmion size is larger than in two-dimensional electron systems.

Experimental analyses of the poly(vinyl chloride) foams' mechanical anisotropic behavior

Assessing a full set of mechanical properties is a rather complicate task in the case of foams, especially if material models must be calibrated with these results. Many issues, for example anisotropy and heterogeneity, influence the mechanical behavior. This article shows through experimental analyses how the microstructure affects different experimental setups and it also quantifies the degree of anisotropy of a poly(vinyl chloride) foam. Monotonic and cyclic experimental tests were carried out using standard compression specimens and non-standard tensile specimens. Results are complemented and compared with the aid of a digital image correlation technique and scanning electron microscopy analyses. Mechanical properties (e.g., elastic and plastic Poisson's ratios) are evaluated for compression and tensile tests, for two different material directions (normal and in-plane). The material is found to be transversely isotropic. Differences in the results of the mechanical properties can be as high as 100%, or even more depending on the technique used and the loading direction. Also, the experimental analyses show how the material's microstructure behavior, like the evolution of the herein identified yield fronts and a spring back phenomenon, can influence the phenomenological response and the failure mechanisms as well as the hardening curves. POLYM. ENG. SCI., 52:2654-2663, 2012. (C) 2012 Society of Plastics Engineers

Experimental model of tooth movement in mice: A standardized protocol for studying bone remodeling under compression and tensile strains

During orthodontic tooth movement (OTM), alveolar bone is resorbed by osteoclasts in compression sites (CS) and is deposited by osteoblasts in tension sites (TS). The aim of this study was to develop a standardized OTM protocol in mice and to investigate the expression of bone resorption and deposition markers in CS and TS. An orthodontic appliance was placed in C57BL6/J mice. To define the ideal orthodontic force, the molars of the mice were subjected to forces of 0.1 N, 0.25 N, 0.35 N and 0.5 N. The expression of mediators that are involved in bone remodeling at CS and TS was analyzed using a Real-Time PCR. The data revealed that a force of 0.35 N promoted optimal OTM and osteoclast recruitment without root resorption. The levels of TNF-alpha, RANKL, MMP13 and OPG were all altered in CS and TS. Whereas TNF-a and Cathepsin K exhibited elevated levels in CS. RUNX2 and OCN levels were higher in TS. Our results suggest that 0.35 N is the ideal force for OTM in mice and has no side effects. Moreover, the expression of bone remodeling markers differed between the compression and the tension areas, potentially explaining the distinct cellular migration and differentiation patterns in each of these sites. (C) 2012 Elsevier Ltd. All rights reserved.

Valence band tail states in disordered superlattices embedded in wide parabolic AlGaAs well

Optical properties of intentionally disordered multiple quantum well (QW) system embedded in a wide AlGaAs parabolic well were investigated by photoluminescence (PL) measurements as functions of the laser excitation power and the temperature. The characterization of the carriers localized in the individual wells was allowed due to the artificial disorder that caused spectral separation of the photoluminescence lines emitted by different wells. We observed that the photoluminescence peak intensity from each quantum well shifted to high energy as the excitation power was increased. This blue-shift is associated with the filling of localized states in the valence band tail. We also found that the dependence of the peak intensity on the temperature is very sensitive to the excitation power. The temperature dependence of the photoluminescence peak energy from each QW was well fitted using a model that takes into account the thermal redistribution of the localized carriers. Our results demonstrate that the band tails in the studied structures are caused by alloy potential fluctuations and the band tail states dominate the emission from the peripheral wells. (C) 2012 American Institute of Physics. [http://dx.doi.org/10.1063/1.4730769]

Diametral tensile strength and film thickness of an experimental dental luting agent derived from castor oil

The need to develop new dental luting agents in order to improve the success of treatments has greatly motivated research. Objective: The aim of this study was to evaluate the diametral tensile strength (DTS) and film thickness (FT) of an experimental dental luting agent derived from castor oil (COP) with or without addition of different quantities of filler (calcium carbonate - CaCO3). Material and Methods: Eighty specimens were manufactured (DTS N=40; FT N=40) and divided into 4 groups: Pure COP; COP 10%; COP 50% and zinc phosphate (control). The cements were mixed according to the manufacturers' recommendations and submitted to the tests. The DTS test was performed in the MTS 810 testing machine (10 KN, 0.5 mm/min). For FT test, the cements were sandwiched between two glass plates (2 cm(2)) and a load of 15 kg was applied vertically on the top of the specimen for 10 min. The data were analyzed by means of one-way ANOVA and Tukey's test (alpha=0.05). Results: The values of DTS (MPa) were: Pure COP- 10.94 +/- 1.30; COP 10%- 30.06 +/- 0.64; COP 50%- 29.87 +/- 0.27; zinc phosphate- 4.88 +/- 0.96. The values of FT (pm) were: Pure COP- 31.09 +/- 3.16; COP 10%- 17.05 +/- 4.83; COP 50%- 13.03 +/- 4.83; Zinc Phosphate- 20.00 +/- 0.12. One-way ANOVA showed statistically significant differences among the groups (DTS - p=1.01E-40; FT - p=2.4E-10). Conclusion: The experimental dental luting agent with 50% of filler showed the best diametral tensile strength and film thickness.

Cassava starch biodegradable films: Influence of glycerol and clay nanoparticles content on tensile and barrier properties and glass transition temperature

In this this study, glycerol content and its incorporation method on tensile and barrier properties of biodegradable films (BF) based on cassava starch were analyzed. ANOVA showed that the glycerol incorporation method did not influence the results (P > 0.05), however the glycerol content influenced significantly the tensile and barrier properties of the films (P < 0.05). Films prepared with lower glycerol content presented better tensile and barrier properties than films with higher content. Films were then prepared with addition of clay nanoparticles and their tensile and barrier properties and glass transition temperature were measured. ANOVA indicated that both glycerol and clay nanoparticles influenced significantly the tensile and barrier properties (P < 0.05), diminishing film permeability when clay nanoparticles were present, while the glass transition temperature was not influenced (P > 0.05). (C) 2011 Elsevier Ltd. All rights reserved.

Correlations between Subjective Well-being, Dyadic Adjustment and Marital Satisfaction in Brazilian Married People

This study aimed to investigate the relationships between the constructs subjective well-being (SWB), dyadic adjustment (DA) and marital satisfaction (MS). Participants were 106 married Brazilians, of both sexes, with a mean age of 42 (+/- 11) years. Instruments used for the sociodemographic characterization and socioeconomic classification were the Subjective Wellbeing Scale (SWBS), the Dyadic Adjustment Scale (DAS) and the Marital Satisfaction Scale (MSS). Through the analysis of correlations and of stepwise multiple regression, it was verified that all the factors of the dyadic adjustment showed correlation with the marital satisfaction. The satisfaction with life (factor of the SWBS) and dyadic satisfaction (factor of the DAS), were positively and significantly correlated (r = .20; p = .04), which reveals that people who say they are satisfied with life in different domains also do so in relation to the marital experience.

Effect of resonant tunneling on exciton dynamics in coupled dot-well nanostructures

Excitonic dynamics in a hybrid dot-well system composed of InAs quantum dots (QDs) and an InGaAs quantum well (QW) is studied by means of femtosecond pump-probe reflection and continuous wave (cw) photoluminescence (PL) spectroscopy. The system is engineered to bring the QW ground exciton state into resonance with the third QD excited state. The resonant tunneling rate is varied by changing the effective barrier thickness between the QD and QW layers. This strongly affects the exciton dynamics in these hybrid structures as compared to isolated QW or QD systems. Optically measured decay times of the coupled system demonstrate dramatically different response to temperature change depending on the strength of the resonant tunneling or coupling strength. This reflects a competition between purely quantum mechanical and thermodynamical processes.

Learning for well being : Studies using the International Adult Literacy Survey

This thesis is a collection of five independent but closely related studies. The overall purpose is to approach the analysis of learning outcomes from a perspective that combines three major elements, namely lifelonglifewide learning, human capital, and the benefits of learning. The approach is based on an interdisciplinary perspective of the human capital paradigm. It considers the multiple learning contexts that are responsible for the development of embodied potential – including formal, nonformal and informal learning – and the multiple outcomes – including knowledge, skills, economic, social and others– that result from learning. The studies also seek to examine the extent and relative influence of learning in different contexts on the formation of embodied potential and how in turn that affects economic and social well being. The first study combines the three major elements, lifelonglifewide learning, human capital, and the benefits of learning into one common conceptual framework. This study forms a common basis for the four empirical studies that follow. All four empirical studies use data from the International Adult Literacy Survey (IALS) to investigate the relationships among the major elements of the conceptual framework presented in the first study. Study I. A conceptual framework for the analysis of learning outcomes This study brings together some key concepts and theories that are relevant for the analysis of learning outcomes. Many of the concepts and theories have emerged from varied disciplines including economics, educational psychology, cognitive science and sociology, to name only a few. Accordingly, some of the research questions inherent in the framework relate to different disciplinary perspectives. The primary purpose is to create a common basis for formulating and testing hypotheses as well as to interpret the findings in the empirical studies that follow. In particular, the framework facilitates the process of theorizing and hypothesizing on the relationships and processes concerning lifelong learning as well as their antecedents and consequences. Study II. Determinants of literacy proficiency: A lifelong-lifewide learning perspective This study investigates lifelong and lifewide processes of skill formation. In particular, it seeks to estimate the substitutability and complementarity effects of learning in multiple settings over the lifespan on literacy skill formation. This is done by investigating the predictive capacity of major determinants of literacy proficiency that are associated with a variety of learning contexts including school, home, work, community and leisure. An identical structural model based on previous research is fitted to the IALS data for 18 countries. The results show that even after accounting for all factors, education remains the most important predictor of literacy proficiency. In all countries, however, the total effect of education is significantly mediated through further learning occurring at work, at home and in the community. Therefore, the job and other literacy related factors complement education in predicting literacy proficiency. This result points to a virtual cycle of lifelong learning, particularly to how educational attainment influences other learning behaviours throughout life. In addition, results show that home background as measured by parents’ education is also a strong predictor of literacy proficiency, but in many countries this occurs only if a favourable home background is complemented with some post-secondary education. Study III. The effect of literacy proficiency on earnings: An aggregated occupational approach using the Canadian IALS data This study uses data from the Canadian Adult Literacy Survey to estimate the earnings return to literacy skills. The approach adapts a labour segmented view of the labour market by aggregating occupations into seven types, enabling the estimation of the variable impact of literacy proficiency on earnings, both within and between different types of occupations. This is done using Hierarchical Linear Modeling (HLM). The method used to construct the aggregated occupational classification is based on analysis that considers the role of cognitive and other skills in relation to the nature of occupational tasks. Substantial premiums are found to be associated with some occupational types even after adjusting for within occupational differences in individual characteristics such as schooling, literacy proficiency, labour force experience and gender. Average years of schooling and average levels of literacy proficiency at the between level account for over two-thirds of the premiums. Within occupations, there are significant returns to schooling but they vary depending on the type of occupations. In contrast, the within occupational return of literacy proficiency is not necessarily significant. The latter depends on the type of occupation. Study IV: Determinants of economic and social outcomes from a lifewide learning perspective in Canada In this study the relationship between learning in different contexts, which span the lifewide learning dimension, and individual earnings on the one hand and community participation on the other are examined in separate but comparable models. Data from the Canadian Adult Literacy Survey are used to estimate structural models, which correspond closely to the common conceptual framework outlined in Study I. The findings suggest that the relationship between formal education and economic and social outcomes is complex with confounding effects. The results indicate that learning occurring in different contexts and for different reasons leads to different kinds of benefits. The latter finding suggests a potential trade-off between realizing economic and social benefits through learning that are taken for either job-related or personal-interest related reasons. Study V: The effects of learning on economic and social well being: A comparative analysis Using the same structural model as in Study IV, hypotheses are comparatively examined using the International Adult Literacy Survey data for Canada, Denmark, the Netherlands, Norway, the United Kingdom, and the United States. The main finding from Study IV is confirmed for an additional five countries, namely that the effect of initial schooling on well being is more complex than a direct one and it is significantly mediated by subsequent learning. Additionally, findings suggest that people who devote more time to learning for job-related reasons than learning for personal-interest related reasons experience higher levels of economic well being. Moreover, devoting too much time to learning for personal-interest related reasons has a negative effect on earnings except in Denmark. But the more time people devote to learning for personal-interest related reasons tends to contribute to higher levels of social well being. These results again suggest a trade-off in learning for different reasons and in different contexts.

Studio del comportamento meccanico di smalti porcellanati per substrati metallici

Composite porcelain enamels are inorganic coatings for metallic components based on a special ceramic-vitreous matrix in which specific additives are randomly dispersed. The ceramic-vitreous matrix is made by a mixture of various raw materials and elements and in particular it is based on boron-silicate glass added with metal oxides(1) of titanium, zinc, tin, zirconia, alumina, ecc. These additions are often used to improve and enhance some important performances such as corrosion(2) and wear resistance, mechanical strength, fracture toughness and also aesthetic functions. The coating process, called enamelling, depends on the nature of the surface, but also on the kind of the used porcelain enamel. For metal sheets coatings two industrial processes are actually used: one based on a wet porcelain enamel and another based on a dry-silicone porcelain enamel. During the firing process, that is performed at about 870°C in the case of a steel substrate, the enamel raw material melts and interacts with the metal substrate so enabling the formation of a continuous varying structure. The interface domain between the substrate and the external layer is made of a complex material system where the ceramic vitreous and the metal constituents are mixed. In particular four main regions can be identified, (i) the pure metal region, (ii) the region where the metal constituents are dominant compared with the ceramic vitreous components, (iii) the region where the ceramic vitreous constituents are dominant compared with the metal ones, and the fourth region (iv) composed by the pure ceramic vitreous material. It has also to be noticed the presence of metallic dendrites that hinder the substrate and the external layer passing through the interphase region. Each region of the final composite structure plays a specific role: the metal substrate has mainly the structural function, the interphase region and the embedded dendrites guarantee the adhesion of the external vitreous layer to the substrate and the external vitreous layer is characterized by an high tribological, corrosion and thermal shock resistance. Such material, due to its internal composition, functionalization and architecture can be considered as a functionally graded composite material. The knowledge of the mechanical, tribological and chemical behavior of such composites is not well established and the research is still in progress. In particular the mechanical performances data about the composite coating are not jet established. In the present work the Residual Stresses, the Young modulus and the First Crack Failure of the composite porcelain enamel coating are studied. Due to the differences of the porcelain composite enamel and steel thermal properties the enamelled steel sheets have residual stresses: compressive residual stress acts on the coating and tensile residual stress acts on the steel sheet. The residual stresses estimation has been performed by measuring the curvature of rectangular one-side coated specimens. The Young modulus and the First Crack Failure (FCF) of the coating have been estimated by four point bending tests (3-7) monitored by means of the Acoustic Emission (AE) technique(5,6). In particular the AE information has been used to identify, during the bending tests, the displacement domain over which no coating failure occurs (Free Failure Zone, FFZ). In the FFZ domain, the Young modulus has been estimated according to ASTM D6272-02. The FCF has been calculated as the ratio between the displacement at the first crack of the coating and the coating thickness on the cracked side. The mechanical performances of the tested coated specimens have also been related and discussed to respective microstructure and surface characteristics by double entry charts.