Marine micro and macro algal species as biosorbents for heavy metals

This paper reviews some practical aspects of the application of algal biomass for the biosorption of heavy metals from wastewater. The ability of different algal species to remove metals varies with algal group and morphology, with the speciation of specific metals and their competition with others in wastewater, and with environmental or process factors. The scattered literature on the uptake of heavy metals by both living and dead algal biomass - both macroalgae and immobilized microalgae - has been reviewed, and the uptake capacity and efficiency of different species, as well as what is known about the mechanisms of biosorption, are presented. Data on metal uptake have commonly been fitted to equilibrium models, such as the Langmuir and Freundlich isotherm models, and the parameters of these models permit the uptake capacity of different algal species under different process conditions to be compared. Higher uptake capacities have been found for brown algae than for red and green algae. Kelps and fucoids are the most important groups of algae used for biosorption of heavy metals, probably because of their abundant cell wall polysacchrides and extracellular polymers. Another important practical aspect is the possibility of re-using algal biomass in several adsorption/desorption cycles (up to 10 have been used with Sargassum spp), and the influence of morphology and environmental conditions on the re-usability of algal tissue is also considered.

Analysis of multiple aspects of a repeated signal: power and rate of rapping during shell fights in hermit crabs

Repeated activities used by animals during contests are assumed to act as signals advertising the quality of the sender. However, their exact functions are not well understood and observations fit only a limited set of the predictions made by models of signaling systems. Experimental studies of contest behavior tend to focus on analysis of the rate of signaling, but individual performances may also vary in magnitude. Both of these features can vary between outcomes and within contests. We examined changes in the rate and power of shell rapping during shell fights in hermit crabs. We show that both rate and power decline during the course of the encounter and that the duration of pauses between bouts of shell rapping increases with an index of the total effort put into each bout. This supports the idea that the vigor of shell rapping is regulated by fatigue and could therefore act as a signal of stamina. By examining different interacting components of this complex activity, we gain greater insight into its function than would be achieved by investigating a single aspect in isolation.

Young Women’s Positive and Negative Perceptions of Self in Northern Ireland

This paper represents analysis of one aspect of a larger research project examining the everyday lives and experiences of young women in Northern Ireland. As an introductory exercise within focus groups, 48 young women considered and discussed the good and not so good things about being a young woman in Northern Ireland. Through these accounts many issues emerged, some in direct contrast and contradiction to one another. The area focused upon for the purpose of this paper is the body, particularly with regard to body image (self-expression versus pressure) and becoming a woman (growing up versus menarche). The aim is to illustrate that what young women cite as being potentially positive aspects of growing up or being a young woman often have negative experiences and implications attached to them. In light of the advancements made by young women in Northern Irish society, an opening of opportunities and their awareness of the persistence of gendered messages regarding their bodies, many young women are of the belief that such messages have less impact upon them today and that gender is a barrier that can be overcome. It is illustrated and argued here, however, that dominant cultural messages regarding women’s bodies are more subtle, confusing and perhaps pervasive than they ever have been. As a consequence, this has created more pressure and confusion for young women and tensions exist in terms of young women’s beliefs and their actions. In light of these research findings, this paper considers practice implications for those working with and for young women.

Electrical and Rheological Percolation of PMMA/MWCNT Nanocomposites as a Function of CNT Geometry and Functionality

The ability of carbon nanotubes (CNTs) to reinforce and enhance the electrical conductivity of polymer matrices is a function of both the aspect ratio and surface chemistry of the CNTs. Hitherto, due to the variability in MWCNT synthesis methods it has not been possible to study the effect of MWCNT aspect ratio and functionality on polymer composite properties. This paper was the first to report the correlation between MWCNT aspect ratio and functionality on the formation of electrical and rheological percolated networks. Furthermore, the fundamental ballistic conductance of MWCNTs made using arc discharge and chemical vapour deposition techniques was reported.

Towards Educational Inclusion in a Transforming Society: Some Lessons from Community Relations and Special Needs Education in Northern Ireland

This paper takes an original approach to an important aspect of educational research and its role in transforming societies, namely that of educational inclusion. It brings together what some might consider two rather strange bedfellows i.e. community relations and special needs education. It also draws upon new tools for theorising educational inclusion, which give a central role to the discursive nature of human conduct and which take a view of human behaviour as socially embedded and meaningful.

The Rights of Religious Associations to External Relations: A Comparative Study of the OSCE and the Council of Europe

This paper argues that religious associations have a number of substantive rights when it comes to their external relations. It does so though comparing the position of the OSCE and the Council of Europe. This paper considers whether the emerging framework includes: (1) a right to legal entity status, (2) a right to establish and run charitable or educational institutions, (3) a right to privileges and substantive benefits and (4) a right to anything else. It concludes that the current developments are welcome because religious freedom has a collective aspect that is essential to the lives of many believers.

Antibody Targeting of Cathepsin S Inhibits Angiogenesis and Synergistically Enhances Anti-VEGF

BACKGROUND: Angiogenesis is a key hallmark of tumourigenesis and its inhibition is a proven strategy for the development of novel anti-cancer therapeutics. An important aspect of early angiogenesis is the co-ordinated migration and invasion of endothelial cells through the hypoxic tumour tissue. Cathepsin S has been shown to play an important role in angiogenesis as has vascular endothelial growth factor (VEGF). We sought to assess the anti-angiogenic effect of Fsn0503, a novel cathepsin S inhibitory antibody, when combined with anti-VEGF on vascular development.

METHODOLOGY/PRINCIPAL FINDINGS: Cathepsin S expression and secretion from endothelial cells was characterised using RT-PCR and western blotting. We further show that cathepsin S promotes pericellular hydrolysis of extracellular matrix components in the tumour microenvironment and facilitates endothelial invasion. The cathepsin S inhibitory antibody, Fsn0503, blocks extracellular proteolysis, inhibiting endothelial invasion and tube formation in cell-based assays. The anti-angiogenic effects of Fsn0503 were also shown in vivo where it significantly retarded the development of vasculature in human xenograft models. Furthermore, when Fsn0503 was combined with an anti-VEGF antibody, a synergistic inhibition of microvascular development was observed.

CONCLUSIONS/SIGNIFICANCE: Taken together, this data demonstrates that the antibody-mediated targeting of cathepsin S represents a novel method of inhibiting angiogenesis. Furthermore, when used in combination with anti-VEGF therapies, Fsn0503 has the potential to significantly enhance current treatments of tumour neovascularisation and may also be of use in the treatment of other conditions associated with inappropriate angiogenesis.

Automated mixed dimensional modelling from 2D and 3D CAD models

The motivation for this paper is to present procedures for automatically creating idealised finite element models from the 3D CAD solid geometry of a component. The procedures produce an accurate and efficient analysis model with little effort on the part of the user. The technique is applicable to thin walled components with local complex features and automatically creates analysis models where 3D elements representing the complex regions in the component are embedded in an efficient shell mesh representing the mid-faces of the thin sheet regions. As the resulting models contain elements of more than one dimension, they are referred to as mixed dimensional models. Although these models are computationally more expensive than some of the idealisation techniques currently employed in industry, they do allow the structural behaviour of the model to be analysed more accurately, which is essential if appropriate design decisions are to be made. Also, using these procedures, analysis models can be created automatically whereas the current idealisation techniques are mostly manual, have long preparation times, and are based on engineering judgement. In the paper the idealisation approach is first applied to 2D models that are used to approximate axisymmetric components for analysis. For these models 2D elements representing the complex regions are embedded in a 1D mesh representing the midline of the cross section of the thin sheet regions. Also discussed is the coupling, which is necessary to link the elements of different dimensionality together. Analysis results from a 3D mixed dimensional model created using the techniques in this paper are compared to those from a stiffened shell model and a 3D solid model to demonstrate the improved accuracy of the new approach. At the end of the paper a quantitative analysis of the reduction in computational cost due to shell meshing thin sheet regions demonstrates that the reduction in degrees of freedom is proportional to the square of the aspect ratio of the region, and for long slender solids, the reduction can be proportional to the aspect ratio of the region if appropriate meshing algorithms are used.

CsF and alumina: A mixed homogeneous-heterogeneous catalytic system for the transesterification of sunflower oil with methanol

The activity and nature (i e heterogeneous and/or homogeneous) of catalysts based on CsF supported on alpha-Al2O3 were investigated for the transesterification of vegetable oil with methanol. The effect of the activation temperature, CsF loading and the reusability in a recirculating reactor were first studied CsF/alpha-Al2O3 exhibited the highest activity for a CsF loading of 0 6 mmol/g and when activated at 120 degrees C An important aspect of this study is the effect of CsF leaching into the reaction mixture, which is attributed to the high solubility of CsF in methanol, leading to a complete loss of activity after one run It was Identified that the activity of the catalyst resulted from a synergy between alumina and dissolved CsF, the presence of both compounds being absolutely necessary to observe any conversion The use of an alumina with a higher surface area resulted in a far greater reaction rate, showing that the concentration of surface site on the oxide (probably surface hydroxyl) was rate-limiting in the case of the experiments using the low surface area alpha-Al2O3 This work emphasizes that combined homogeneous-heterogeneous catalytic systems made from the blending of the respective catalysts can be used to obtain high conversion of vegetable oil to biodiesel. Despite the homogeneous/heterogeneous dual character, such a catalytic system may prove valuable in developing a simple and cost-effective continuous catalytic process for biodiesel production (C) 2010 Elsevier B V All rights reserved

Melt-compounded nanocomposites of titanium dioxide atomic-layer-deposition-coated polyamide and polystyrene powders

Polyamide and polystyrene particles were coated with titanium dioxide films by atomic layer deposition (ALD) and then melt-compounded to form polymer nanocomposites. The rheological properties of the ALD-created nanocomposite materials were characterized with a melt flow indexer, a melt flow spiral mould, and a rotational rheometer. The results suggest that the melt flow properties of polyamide nanocomposites were markedly better than those of pure polyamide and polystyrene nanocomposites. Such behavior was shown to originate in an uncontrollable decrease in the polyamide molecular weight, likely affected by a high thin-film impurity content, as shown in gel permeation chromatography (GPC) and scanning electron microscope (SEM) equipped with an energy-dispersive spectrometer. Transmission electron microscope image showed that a thin film grew on both studied polymer particles, and that subsequent melt-compounding was successful, producing well dispersed ribbon-like titanium dioxide with the titanium dioxide filler content ranging from 0.06 to 1.12wt%. Even though we used nanofillers with a high aspect ratio, they had only a minor effect on the tensile and flexural properties of the polystyrene nanocomposites. The mechanical behavior of polyamide nanocomposites was more complex because of the molecular weight degradation. Our approach here to form polymeric nanocomposites is one way to tailor ceramic nanofillers and form homogenous polymer nanocomposites with minimal work-related risks in handling powder form nanofillers. However, further research is needed to gauge the commercial potential of ALD-created nanocomposite materials. Copyright (C) 2011 John Wiley & Sons, Ltd.

Secularism and Religion in Nineteenth-Century Germany: The Rise of the Fourth Confession

Negotiating the boundaries of the secular and of the religious is a core aspect of modern experience. In mid-nineteenth-century Germany, secularism emerged to oppose church establishment, conservative orthodoxy, and national division between Catholics, Protestants, and Jews. Yet, as historian Todd H. Weir argues in this provocative book, early secularism was not the opposite of religion. It developed in the rationalist dissent of Free Religion and, even as secularism took more atheistic forms in Freethought and Monism, it was subject to the forces of the confessional system it sought to dismantle. Similar to its religious competitors, it elaborated a clear worldview, sustained social milieus, and was integrated into the political system. Secularism was, in many ways, Germany's fourth confession. While challenging assumptions about the causes and course of the Kulturkampf and modern antisemitism, this study casts new light on the history of popular science, radical politics, and social reform.

Psychological adjustment to Type 2 Diabetes and relationship quality

Aims To examine the associations between psychological adjustment to Type 2 diabetes and the reported quality and type of relationships with partners. Methods All participants (n = 88) completed a number of questionnaires, including twomeasures of relationship quality: the Dyadic Adjustment Scale and the PersonalAssessment of Intimacy inRelationships Scale, theDiabetesQuality of Life Scale and the ATT-19 (which assesses personal integration of diabetes). Additionally, HbA1c levels were obtained from medical notes. Results Measures of relationship quality significantly contributed to the explanation of two outcomes: personal integration of diabetes and satisfaction with the burden of self-management behaviours. More specifically, the findings demonstrate that a specific aspect of relationship quality—intimacy in recreational activities—is positively associated with the outcomesmentioned above. Conclusions People with Type 2 diabetes who are not taking insulin, who share engagement in physical activities with their partner are more likely to be psychologically well-adjusted to their diagnosis of diabetes.

Myocardial infarction in the C57BL/6J mouse - A quantifiable and highly reproducible experimental model

Introduction: The laboratory mouse is a powerful tool in cardiovascular research. In this report, we describe a method for a reproducible mouse myocardial infarction model that would allow subsequent comparative and quantitative studies on molecular and pathophysiological variables. Methods: (A) The distribution of the major coronary arteries including the septal artery in the left ventricle of the C57BL/6J mice (n=20) was mapped by perfusion of latex dye or fluorescent beads through the aorta. (B) The territory of myocardial infarction after the ligation of the most proximal aspect of the left anterior descending (LAD) coronary artery was quantified. (C) The consistency in the histological changes parallel to the infarction at different time points was analyzed. Results: (A) The coronary artery tree of the mouse is different from human and, particularly, in regard to the blood supply of the septum. (B) Contrary to previous belief, the septal coronary artery in the mouse is variable in origin. (C) A constant ligation of the LAD immediately below the left auricular level ensures a statistically significant reproducible infarct size. (D) The ischemic changes can be monitored at a histological level in a way similar to what is described in the human. Conclusion: We illustrate a method for maximal reproducibility of experimental acute myocardial infarction in the mouse model, due to a consistent loss of perfusion in the lower half of the left ventricle. This will allow the study of molecular and physiological variables in a controlled and quantifiable experimental model environment. (C) 2004 Elsevier Inc. All rights reserved.

The Battle of the Somme in Ulster memory and identity

One of the enduring illusions about Northern Ireland is that its society can be conceptualized through a binary distinction between protestant and catholic. unionist and nationalist. It is increasingly apparent that these broad domains are themselves fractured and diverse and that otherness is often conceived from within rather than without. Northern Ireland can also be viewed as a laboratory for identity formation as unionists and loyalists strive to reconcile themselves with the fundamental political changes that have followed in the wake of the Peace Process. This paper considers one aspect of the contestation of belonging that increasingly characterizes unionism. It examines the competition for the ownership of the mythology of the Battle of the Somme ( 1916), long a key event in the unionist narrative. In particular, the paper addresses the ways in which paramilitary organizations are using the Somme to legitimate their own activities but also to distance the loyalist working classes from the former hegemonic Britishness of official unionism and the sectarianism of the Orange Order. The analysis concludes that loyalist identity is being conceptualized thorough a narrative of betrayal from within and at an intensely localized scale.

Preparation and characterisation of cellulose nanofibres

Two different procedures were compared for the preparation of cellulose nanofibres from flax and microcrystalline cellulose (MCC). The first involved a combination of high energy ball milling, acid hydrolysis and ultrasound, whilst the second employed a high pressure homogenisation technique, with and without various pre-treatments of the fibrous feedstock. The geometry and microstructure of the cellulose nanofibres were observed by SEM and TEM and their particle size measured using image analysis and dynamic light scattering. Aspect ratios of nanofibres made by microfluidisation were orders of magnitude greater than those achieved by acid hydrolysis. FTIR, XRD and TGA were used to characterise changes to chemical functionality, cellulose crystallinity and thermal stability resulting from the approaches used for preparing the cellulose nanofibres. Hydrolysis using sulphuric acid gave rise to esterification of the cellulose nanofibres, a decrease in crystallinity with MCC, but an increase with flax, together with an overall reduction in thermal stability. Increased shear history of flax subjected to multiple passes through the microfluidiser, raised both cellulose nanofibril crystallinity and thermal stability, the latter being strongly influenced by acid, alkaline and, most markedly, silane pretreatment.