Chloride induced corrosion of steel in alkali activated slag concretes

Alkali activated slag (AAS) is an alternative cementitious material. Sodium silicate solution is usually used to activate ground granulated blast furnace slag to produce AAS. As a consequence, the pore solution chemistry of AAS differs from that of Portland cement (PC). Although AAS offers many advantages over PC, such as higher strength, superior resistance to acid and sulphate environments and lower embodied carbon due to 100% PC replacement, there is a need to assess its performance against chloride induced corrosion duo to its different pore solution chemistry. For PC systems, resistivity measurement, as a type of nondestructive test, is usually used to evaluate its chloride diffusivity and the corrosion rate of the embedded steel. However, due to the different pore solution chemistry present in the different AAS systems, the application of this test in AAS concretes would be questionable as the resistivity of concrete is highly dependent on its conductivity of the pore solution. Therefore, a study was carried out using twelve AAS concretes mixes, the results of which are reported in this paper. The AAS mixes were designed with alkali concentration of 4%, 6% and 8% (Na₂O% of the mass of slag) and modulus (Ms) of sodium silicate solution of 0.75, 1.00, 1.50 and 2.00. A PC concrete with the same binder content as the AAS concretes was also studied as a reference. The chloride diffusion coefficient was determined using a non-steady state chloride diffusion test (NT BUILD 443). The resistivity of the concretes before the diffusion test was also measured. Macrocell corrosion current (corrosion rate) for steel rods embedded in the concretes was measured whilst subjecting the concretes to a cyclic chloride ponding regime (1 day ponded with salt solution and 6 days drying). The results showed that the AAS concretes had lower chloride diffusivity with associated higher resistivity than the PC concrete. The measured corrosion rate was also lower for the AAS concretes. However, unlike the PC, in which a higher resistivity yields a lower diffusivity and corrosion rate, there was no relationship apparent between the resistivity and either the diffusivity or the corrosion rate of steel for the AAS concretes. This is assigned to the variation of the pore solution composition of the AAS concretes. This also means that resistivity measurements cannot be depended on for assessing the chloride induced corrosion resistance of AAS concretes.

High resolution monitoring of surface morphological change of building limestones in response to simulated salt weathering

A salt weathering simulation using a mix of sodium chloride (5%) and magnesium sulphate (5%) in a salt corrosion cabinet and five granular limestones is described. Progressive surface loss from vertical exposed faces was mapped using a high resolution (sub-millimetre) object scanner (Konica Minolta Vi9i). Patterns of loss are related to surface porosity/permeability measurements obtained using a hand-held gas permeameter. Introduction of this spatial dimension into damage assessment is seen as essential for understanding the initial conditions that allow surface loss to be triggered, and changes in surface characteristics as weathering proceeds which dictate subsequent decay in space and time. Preliminary observations suggest that scanning at this high resolution is particularly valuable in quantifying very subtle trends and distortions that are pre-cursors to material loss, including surface swelling and pore filling.

NPY Y1 and VPAC1 receptor expression in human dental pulps

Neuropeptides such as neuropeptide Y (NPY) and vasoactive intestinal polypeptide (VIP) have been shown by our research group to be present in human dental pulp tissue. Neuropeptides cannot cross cell membranes and therefore to exert their biological effects they must bind to selected receptors on the surface of target cell membranes. However, the expression of receptor proteins for NPY and/or VIP have yet to be reported in human pulp tissue. The presence of neuropeptide receptors can be conveniently determined by Western blotting using specific anti-receptor antibodies. Objectives: The aim of this work was to identify the presence of the NPY Y1 receptor and the VIP receptor VPAC1 in human dental pulp tissue from both intact and carious teeth using Western blotting. Methods: Pulp tissue was collected from both intact and carious teeth and membrane preparations from these tissues were then subject to sodium dodecyl sulphate gel electrophoresis (SDS-PAGE), transferred to nitrocellulose and probed with specific antibodies to either the NPY Y1 receptor or the VPAC1 receptor. Results: Individual Western blotting experiments revealed the presence of immunoreactive bands corresponding to the known molecular weights of the NPY Y1 and VPAC1 receptor proteins in both intact and carious pulp samples. Conclusions: Demonstration of the presence of NPY Y1 and VPAC1 receptor protein expression in pulpal tissue from intact and carious teeth provides further support for the roles of these neuropeptides in pulpal health and disease.

Effects of Poly (ε-caprolactone) Coating on the Properties of Three-Dimensional Printed Porous Structures

Powder-based inkjet three-dimensional printing (3DP) to fabricate pre-designed 3D structures has drawn increasing attention. However there are intrinsic limitations associated with 3DP technology due to the weak bonding within the printed structure, which significantly compromises its mechanical integrity. In this study, calcium sulphate ceramic structures demonstrating a porous architecture were manufactured using 3DP technology and subsequently post-processed with a poly (ε-caprolactone) (PCL) coating. PCL concentration, immersion time, and number of coating layers were the principal parameters investigated and improvement in compressive properties was the measure of success. Interparticle spacing within the 3DP structures were successfully filled with PCL material. Consequently the compressive properties, wettability, morphology, and in vitro resorption behaviour of 3DP components were significantly augmented. The average compressive strength, Young’s modulus, and toughness increased 217%, 250%, and 315%, following PCL coating. Addition of a PCL surface coating provided long-term structural support to the host ceramic material, extending the resorption period from less than 7 days to a minimum of 56 days. This study has demonstrated that application of a PCL coating onto a ceramic 3DP structure was a highly effective approach to addressing some of the limitations of 3DP manufacturing and allows this advanced technology to be potentially used in a wider range of applications.

Biomass fly ash incorporation in cement based materials

In recent years, pressures on global environment and energy security have led to an increasing demand on renewable energy sources, and diversification of Europe’s energy supply. Among these resources the biomass could exert an important role, since it is considered a renewable and CO2 neutral energy resource once the consumption rate is lower than the growth rate, and can potentially provide energy for heat, power and transports from the same installation. Currently, most of the biomass ash produced in industrial plants is either disposed of in landfill or recycled on agricultural fields or forest, and most times this goes on without any form of control. However, considering that the disposal cost of biomass ashes are raising, and that biomass ash volumes are increasing worldwide, a sustainable ash management has to be established. The main objective of the present study is the effect of biomass fly ashes in cement mortars and concretes in order to be used as a supplementary cementitious material. The wastes analyzed in the study were collected from the fluidized bed boilers and grate boilers available in the thermal power plants and paper pulp plants situated in Portugal. The physical as well as chemical characterisations of the biomass fly ashes were investigated. The cement was replaced by the biomass fly ashes in 10, 20 and 30% (weight %) in order to investigate the fresh properties as well as the hardened properties of biomass fly ash incorporated cement mortar and concrete formulations. Expansion reactions such as alkali silica reaction (ASR), sulphate attack (external and internal) were conducted in order to check the durability of the biomass fly ash incorporated cement mortars and concretes. Alternative applications such as incorporation in lime mortars and alkali activation of the biomass fly ashes were also attempted. The biomass fly ash particles were irregular in shape and fine in nature. The chemical characterization revealed that the biomass fly ashes were similar to a class C fly ash. The mortar results showed a good scope for biomass fly ashes as supplementary cementitious materials in lower dosages (<20%). The poor workability, concerns about the organic content, alkalis, chlorides and sulphates stand as the reasons for preventing the use of biomass fly ash in high content in the cement mortars. The results obtained from the durability tests have shown a clear reduction in expansion for the biomass fly ash mortars/concretes and the binder blend made with biomass fly ash (20%) and metakaolin (10%) inhibited the ASR reaction effectively. The biomass fly ash incorporation in lime mortars did not improve the mortar properties significantly though the carbonation was enhanced in the 15-20% incorporation. The biomass fly ash metakaolin blend worked well in the alkali activated complex binder application also. Portland cement free binders (with 30-40 MPa compressive strength) were obtained on the alkali activation of biomass fly ashes (60-80%) blended with metakaolin (20-40%).

Desenvolvimento e avaliação de um sistema de monitorização da corrosão electroquímica no betão armado

O presente trabalho teve como principal objectivo desenvolver e avaliar o desempenho de um sistema de monitorização da corrosão no betão armado. Para tal foram construídos dois provetes de classe 20/25, e outros dois de classe 30/35. Dentro desses quatro provetes foram instalados sensores de corrosão designados por Monicorr. Para cada classe de betão utilizaram-se dois tipos diferentes de contaminação, designadas por A e B. A contaminação do tipo A é feita adicionando durante a amassadura do betão uma solução aquosa de cloreto de cálcio a 4% em massa de cimento e sujeitando esses provetes a ciclos de condensação de 50h, durante um período de 1000h. A contaminação do tipo B é feita sujeitando os outros dois provetes de classes diferentes a ciclos de 100h de nevoeiro salino a 3% em massa de água, durante um período de 2000h. Para avaliar o desempenho do sistema de monitorização Monicorr foram comparados os valores da velocidade de corrosão instantânea por LPR, a resistividade do betão e o potencial de corrosão da armadura, obtidos pelo sistema Monicorr, com os obtidos por aparelhos utilizados para o mesmo efeito em laboratório. Paralelamente, estudou-se também a variação do potencial de corrosão da armadura em função da área oxidada. Para além disso desenvolveu-se um conjunto de pseudo referências de grafite dopada com diferentes percentagens de cimento e avaliou-se a sua estabilidade relativamente ao eléctrodo de calomelanos e óxido de managanês manganês em soluções de hidróxido de cálcio saturada e de betão armado contaminado com sais cloreto. Finalmente foram ainda desenvolvidas duas tarefas, a primeira relacionada com os resultados obtidos na medição da resistividade do betão armado pelas técnicas de dois pinos e quatro pinos, e a segunda com o desenvolvimento de um método rápido de contaminação do betão armado com dióxido de enxofre. Os resultados obtidos permitem concluir que: - o sistema de monitorização Monicorr apresenta um comportamento muito semelhante aos utilizados em laboratório para medir grandezas como o potencial de corrosão da armadura, resistividade do betão e velocidade de corrosão instantânea por LPR; - a monitorização das três grandezas atrás referidas pode ser uma ferramenta importante para permitir saber qual é o desenvolvimento corrosivo de uma estrutura de betão armado; os eléctrodos de grafite dopada com cimento apresentam uma elevada estabilidade nos meios testados tendo um desempenho muito semelhante à referência de manganês óxido de manganês para os mesmos meios. Relativamente à influência da área oxidada no potencial de corrosão da armadura não foi possível tirar conclusões. Foi possível, também, concluir que existe uma clara concordância entre as medições da resistividade do betão utilizando o método dos dois pinos e o método dos quatro pinos. Finalmente pode-se concluir que a metodologia desenvolvida para contaminar provetes de betão com iões sulfato obtém bons resultados ao fim de, apenas, 48h de contaminação.

Indoor air quality in elementary schools of Lisbon and Aveiro

Tem havido uma preocupação crescente com a qualidade do ar interior (QAI) nas escolas em muitos países. Muitos estudos epidemiológicos têm encontrado diferenças regionais entre ambientes interiores. Apesar da elevada incidência de asma e rinite na população infantil, praticamente nada se sabia sobre a QAI em escolas portuguesas. A percepção dos problemas de QAI é crucial para avaliar os riscos para a saúde e rendimento dos estudantes, e para sugerir meios de reduzir a exposição a poluentes indesejáveis. Neste estudo procurou-se obter as concentrações de poluentes de interesse em estabelecimentos de ensino do 1º ciclo de Lisboa e Aveiro, estimar o estado atual de casos de asma e rinite em escolas primárias da capital, avaliar a influência de diferentes materiais das salas de aula/construção e hábitos escolares na QAI, identificar potenciais fontes de poluentes nos interiores e exteriores das salas de aula e propor medidas mitigadoras. Catorze escolas de Lisboa foram visitadas para obter a caracterização física das construções em termos de estrutura, ventilação, materiais de acabamento, produtos de limpeza, densidade de ocupação e potenciais fontes interiores de poluição. Os estudantes foram questionados sobre os seus hábitos e sintomas respiratórios através de inquéritos do modelo ISAAC (International Study of Asthma and Allergies in Childhood). Durante a primavera, outono e inverno (2008-2010), nas salas de aula e pátios, foram monitorizados, por amostragem passiva, compostos orgânicos voláteis (COVs), carbonilos e dióxido de azoto (NO2). Foram também medidos parâmetros de conforto e níveis de microrganismos. Duas escolas localizadas, uma no centro da cidade e outra na região suburbana, em Aveiro foram estudadas em 2010. Parâmetros de conforto, microrganismos, COVs, NO2, material particulado (PM10) foram medidos no interior e no exterior de ambas escolas. Os iões solúveis, carbono orgânico e elementar (OC e EC), e compostos orgânicos presentes no material particulado foram subsequentemente analisados em laboratório. Uma medida mitigadora - fitoremediação - foi avaliada na escola do centro da cidade de Aveiro em 2011. Os resultados do estudo mostraram que a QAI é pior do que a do ar exterior. Em geral, os níveis de CO2 e dos bioaerosóis excederam os níveis máximos aceitáveis para o conforto dos ocupantes estipulado pelas regulamentações portuguesas. Quase todos os COVs e carbonilos identificados mostraram razões interior/exterior (I/E) maiores que uma unidade, o que demonstra a importante contribuição de fontes interiores em todas as escolas. As razões I/E das concentrações de NO2 nunca excederam a unidade. Os níveis interiores diários de PM10 foram sempre maiores que os exteriores, exceto nos fins de semana. Após a colocação de plantas numa das salas de aula, observou-se uma redução estatisticamente significativa nos níveis de CO2, COVs, carbonilos, PM10, OC, e dos iões nitrato, sulfato, amónia, cálcio e carbonato. A possível redução dos níveis de poluentes no interior após a colocação de plantas pode representar uma solução de baixo custo para reduzir a exposição a muitos compostos, melhorar o rendimento e aumentar o bem estar dos alunos e professores em sala de aula.

Integration of geochemical and biological modifications in mining areas: waters, sediments and diatoms

The development of mining activities over thousands of years in the region of Aljustrel is nowadays visible as a vast area of ore tailings, slag and host rocks of sulphides mineralization. The generation of acidic waters by the alteration of pyritic minerals - Acid Mine Drainage (AMD) - causes a significant impact on the river system both in the south of the village (Rib ª. Água Forte) and in the north of it (Rib ª. Água Azeda and Barranco do Farrobo), which is reflected in extremely low pH values (< 3) and high concentrations of As, Cd, Cu, Fe, Mn, Pb, Zn and sulphates. This study aimed to assess the environmental impacts extent, integrating geochemical (surface waters and stream sediments) and biological (diatoms) parameters. Three groups of sites were defined, based on sediments and water analysis, which integration with diatom data showed the same association of groups: Group 1- impacted, with acidic pH (1.9-5.1), high metal contents (0.4-1975 mg L-1) and Fe-Mg-sulphate waters, being metals more bioavailable in waters in cationic form (Me2+); mineralogically the sediments were characterized by phyllosilicates and sulphates/oxy-hydroxysulphate phases, easily solubilized, retaining a high amount of metals when precipitated; dominant taxon was Pinnularia aljustrelica (a new species); Group 2- slightly impacted, weak acid to neutral pH (5.0-6.8), metal contents not so high (0.2-25 mg L-1) and Fe-Mg-sulphate to Mg-chloride waters; dominant taxa were Brachysira neglectissima and Achnanthidium minutissimum; Group 3- unimpacted, alkaline pH (7.0-8.4), low metal contents (0-7 mg L-1) with Mg-chloride waters. In this group, metals were associated to the primary phases (e.g. sulphides), not so easily available; the existence of high chloride contents explained the presence of typical taxa of brackish/marine (e.g. Entomoneis paludosa) waters. Taxonomical aspects of the diatoms were studied (discovery of a new species: Pinnularia aljustrelica Luis, Almeida et Ector sp. nov.), as well as morphometric (size decrease of diatoms valves, as well as the appearance of deformed valves of Eunotia exigua in Group 1 and A. minutissimum in Group 2) and physiological (effective to assess the effects of metals/acidity in the photosynthetic efficiency through PAM Fluorometry) aspects. A study was carried out in an artificial river system (microcosm) that aimed to mimic Aljustrel’s extreme conditions in controlled laboratory conditions. The chronic effects of Fe, SO42- and acidity in field biofilms, inoculated in the artificial rivers, were evaluated as well as their contribution to the communities’ tolerance to metal toxicity, through acute tests with two metals (Cu and Zn). In general, the effects caused by low pH values and high concentrations of Fe and SO42- were reflected at the community level by the decrease in diversity, the predominance of acidophilic species, the decrease in photosynthetic efficiency and the increase of enzymatic (e.g. catalase, superoxide dismutase) and non-enzymatic activities (e.g. total glutathione and total phytochelatins). However, it was possible to verify that acidity performed a protective effect in the communities, upon Cu and Zn addition. A comparative study between Aljustrel mining area and New Brunswick mining area was carried out, both with similar mining and geological conditions, reflected in similar diatom communities in both mines, but in very different geographic and climatic areas.

Estudo da variação da abundância e diversidade de procariotas em sedimentos subsuperficiais marinhos

Os sedimentos marinhos subsuperficiais profundos são, atualmente, um ambiente ainda pouco conhecido do ponto de vista microbiológico, nomeadamente quanto aos processos metabólicos que nele têm lugar e quanto à sua possível influência nos ciclos biogeoquímicos. O acesso a amostras colhidas em sedimentos profundos, particularmente no âmbito dos programas IODP (International Ocean Discovery Program) e ECORD (European Consortium for Ocean Research Drilling) tem permitido recolher informação sobre a estrutura das comunidades de procariotas bem como sobre alguns dos fatores que regulam a sua distribuição e atividade. Este estudo teve como objetivo caracterizar a distribuição e a diversidade estrutural das comunidades de procariotas em sedimentos subsuperficiais profundos colhidos no Arco Izu-Bonin-Mariana, no mar das Filipinas, com recurso a métodos independentes de cultivo (PCR-DGGE) e à contagem de células por microscopia de epifluorescência. Os resultados apontam para a existência de comunidades de Bacteria e Archaea diversas. Os valores do índice de diversidade de Shannon-Weaver (H’) calculados com base nos perfis de DGGE (Bacteria) foram significativamente mais elevados (3,035 – 1,971) nas camadas superficiais (< 140 mafm) do que nos sedimentos (2,519 - 1,049) correspondentes a profundidades superiores entre 163 e 879 mafm. A abundância máxima (8,66 x 106 células.gps-1) foi registada à profundidade de 67 mafm e valor mínimo (2,26 x 106 células.gps-1) foi observado em amostras colhidas a 879 mafm de profundidade. Abundância e diversidade apresentaram correlação negativa com a profundidade e com o teor de sulfato. Os resultados indicam que ao longo da coluna de sedimento se estabelecem comunidades de procariotas estruturalmente diferentes e adaptadas ao ambiente geoquímico prevalecente, nomeadamente em termos dos aceitadores de eletrões disponíveis. O estudo do microbioma destas amostras representativas do ambiente sedimentar subsuperficial profundo será continuado e detalhado, com recurso a técnicas de sequenciação avançada.

Effects of copper in plasma, gills, liver and muscle of seabream (Sparus aurata, Linnaeus 1758) juveniles

Dissertação de Mestrado, Aquacultura e Pescas, Faculdade de Ciências do Mar e do Ambiente, Universidade do Algarve, 2006

Caracterização fisiológica e nutritiva da clorose férrica em citrinos

Tese dout., Ciências Agrárias, Produção Vegetal, Unidade de Ciências e Tecnologias Agrárias, Universidade do Algarve, 2000

Bio-removal of toxic metals by metal resistant anaerobic bacteria: molecular characterization and performance studies

Tese de dout., Ciências Biotecnológicas (Biotecnologia Ambiental), Faculdade de Ciências e Tecnologia, Univ. do Algarve, 2010

Microbial community composition and mercury cycling in sediments of tagus estuary

Tese de doutoramento, Farmácia (Toxicologia), Universidade de Lisboa, Faculdade de Farmácia, 2016

Determination of carbamate and urea pesticide residues in fresh vegetables using microwave-assisted extraction and liquid chromatography

An analytical multiresidue method for the simultaneous determination of seven pesticides in fresh vegetable samples, namely, courgette (Cucurbita pepo), cucumber (Cucumis sativus), lettuce (Lactuca sativa, Romaine and Iceberg varieties) and peppers (Capsicum sp.) is described. The procedure, based on microwave-assisted extraction (MAE) and analysis by liquid chromatography– photodiode array (LC–PDA) detection was applied to four carbamates (carbofuran, carbaryl, chlorpropham and EPTC) and three urea pesticides (monolinuron, metobromuron and linuron). Extraction solvent and the addition of anhydrous sodium sulphate to fresh vegetable homogenate before MAE were the parameters optimised for each commodity. Recovery studies were performed using spiked samples in the range 250–403 µgkg- 1 in each pesticide. The pesticide residues were extracted using 20mL acetonitrile at 60 ºC, for 10 min. Acceptable recoveries and RSDs were attained (overall average recovery of 77.2% and RSDs are lower than 11%). Detection limits ranged between 5.8 µgkg- 1 for carbaryl to 12.3 µgkg- 1 for carbofuran. The analytical protocol was applied for quality control of 41 fresh vegetable samples bought in Oporto Metropolitan Area (North Portugal). None of the samples contained any detectable amounts of the studied compounds.

Agar extraction from integrated multitrophic aquacultured Gracilaria vermiculophylla: Evaluation of a microwave-assisted process using response surface methodology

Microwave-assisted extraction (MAE) of agar from Gracilaria vermiculophylla, produced in an integrated multitrophic aquaculture (IMTA) system, from Ria de Aveiro (northwestern Portugal), was tested and optimized using response surface methodology. The influence of the MAE operational parameters (extraction time, temperature, solvent volume and stirring speed) on the physical and chemical properties of agar (yield, gel strength, gelling and melting temperatures, as well as, sulphate and 3,6-anhydro-Lgalactose contents) was evaluated in a 2^4 orthogonal composite design. The quality of the extracted agar compared favorably with the attained using traditional extraction (2 h at 85ºC) while reducing drastically extraction time, solvent consumption and waste disposal requirements. Agar MAE optimum results were: an yield of 14.4 ± 0.4%, a gel strength of 1331 ± 51 g/cm2, 40.7 ± 0.2 _C gelling temperature, 93.1 ± 0.5ºC melting temperature, 1.73 ± 0.13% sulfate content and 39.4 ± 0.3% 3,6-anhydro-L-galactose content. Furthermore, this study suggests the feasibility of the exploitation of G. vermiculophylla grew in IMTA systems for agar production.