Transient ventilation dynamics induced by heat sources of unequal strength

We examine theoretically the transient displacement flow and density stratification that develops within a ventilated box after two localized floor-level heat sources of unequal strengths are activated. The heat input is represented by two non-interacting turbulent axisymmetric plumes of constant buoyancy fluxes B1 and B2 > B1. The box connects to an unbounded quiescent external environment of uniform density via openings at the top and base. A theoretical model is developed to predict the time evolution of the dimensionless depths λj and mean buoyancies δj of the 'intermediate' (j = 1) and 'top' (j = 2) layers leading to steady state. The flow behaviour is classified in terms of a stratification parameter S, a dimensionless measure of the relative forcing strengths of the two buoyant layers that drive the flow. We find that dδ1/dτ α 1/λ1 and dδ2/dτ α 1/λ2, where τ is a dimensionless time. When S 1, the intermediate layer is shallow (small λ1), whereas the top layer is relatively deep (large λ2) and, in this limit, δ1 and δ2 evolve on two characteristically different time scales. This produces a time lag and gives rise to a 'thermal overshoot', during which δ1 exceeds its steady value and attains a maximum during the transients; a flow feature we refer to, in the context of a ventilated room, as 'localized overheating'. For a given source strength ratio ψ = B1/B2, we show that thermal overshoots are realized for dimensionless opening areas A < Aoh and are strongly dependent on the time history of the flow. We establish the region of {A, ψ} space where rapid development of δ1 results in δ1 > δ2, giving rise to a bulk overturning of the buoyant layers. Finally, some implications of these results, specifically to the ventilation of a room, are discussed. © Cambridge University Press 2013.

THE RESPONSES OF Microcystis TO SEDIMENT ENVIRONMENTS AND THE ASSESSMENT FOR ITS OVERWINTERING - A SIMULATION STUDY IN A NOVEL DEVICE

A novel multi-cell device made of organic glass was designed to study morphological and physiological characteristics of Microcystis population trapped in simulated sediment conditions. Changes of colonial morphology and antioxidant activities of the population were observed and measured over the range of 31-day incubation. During the incubation, the antioxidant enzyme activities fluctuated significantly in sediment environments. The activities of catalase (CAT), glutathione peroxidase (GPx) and malondialdehyde (NIDA) reached the highest on the 11(th) day, 6(th) day and 6(th) day. respectively, and then dropped down remarkably in the following days. The ratios of Fv/Fm and the maximal electron transfer rate (ETRm) declined during the initial days (1 similar to 11(th) day), but rebounded on the 16(th) day, which were consistent with the variations of total protein. In the end of incubation. gas vacuoles were hard]), observed and the gelatinous sheath was partly disappeared in the population of Microcystis. Nevertheless, the remaining populations. upon transferred to culture medium, were able to grow though experiencing a longer lag phase of nine days. The results indicated that the sediment environments were able to cause negative effects on M. aeruginosa cells. The cells, however, responded to against the possible damage afterwards. It is thus proposed the acute responses in the population during the early stage of sedimentation could be of importance in aiding the long-term survivor of Microcystis and recruitment in lake sediments. The present study also demonstrated the utility of the device in simulating the sediment environments for further investigation.

A laboratory study on risk assessment of microcystin-RR in cropland

The persistence time and risk of microcystin-RR (MC-RR) in cropland via irrigation were investigated under laboratory conditions. In order to evaluate the efficiency of the potential adsorption and biodegradation of MC-RR in cropland and the persistence time of MC-RR for crop irrigation, high performance liquid chromatography (HPLC) was used to quantify the amount of MC-RR in solutions. Our study indicated that MC-RR could be adsorbed and biodegraded in cropland soils. MC-RR at 6.5 mg/L could be completely degraded within 6 days with a lag phase of 1 - 2 days. In the presence of humic acid, the same amount of MC-RR could be degraded within 4 days without a lag phase. Accordingly, the persistence time of MC-RR in cropland soils should be about 6 days. This result also suggested the beneficial effects of the organic fertilizer utilization for the biodegradation of MC-RR in cropland soils. Our studies also demonstrated that MC-RR at low concentration (< 10 mu g/L) could accelerate the growth of plants, while high concentration of MC-RR (> 100 mu g/L) significantly inhibited the growth of plants. High sensitivity of the sprouting stage plants to MC-RR treatments as well as the strong inhibitory effects resulting from prolonged irrigation further indicated that this MC-RR growth-inhibition may vary with the duration of irrigation and life stage of the plants. (c) 2007 Published by Elsevier Ltd.

Is performance measurement and management fit for the future?

Performance measurement and management (PMM) is a management and research paradox. On one hand, it provides management with many critical, useful, and needed functions. Yet, there is evidence that it can adversely affect performance. This paper attempts to resolve this paradox by focusing on the issue of "fit". That is, in today's dynamic and turbulent environment, changes in either the business environment or the business strategy can lead to the need for new or revised measures and metrics. Yet, if these measures and metrics are either not revised or incorrectly revised, then we can encounter situations where what the firm wants to achieve (as communicated by its strategy) and what the firm measures and rewards are not synchronised with each other (i.e., there is a lack of "fit"). This situation can adversely affect the ability of the firm to compete. The issue of fit is explored using a three phase Delphi approach. Initially intended to resolve this first paradox, the Delphi study identified another paradox - one in which the researchers found that in a dynamic environment, firms do revise their strategies, yet, often the PMM system is not changed. To resolve this second paradox, the paper proposes a new framework - one that shows that under certain conditions, the observed metrics "lag" is not only explainable but also desirable. The findings suggest a need to recast the accepted relationship between strategy and PMM system and the output included the Performance Alignment Matrix that had utility for managers. © 2013 .

Finding resonance: Adaptive frequency oscillators for dynamic legged locomotion

There is much to gain from providing walking machines with passive dynamics, e.g. by including compliant elements in the structure. These elements can offer interesting properties such as self-stabilization, energy efficiency and simplified control. However, there is still no general design strategy for such robots and their controllers. In particular, the calibration of control parameters is often complicated because of the highly nonlinear behavior of the interactions between passive components and the environment. In this article, we propose an approach in which the calibration of a key parameter of a walking controller, namely its intrinsic frequency, is done automatically. The approach uses adaptive frequency oscillators to automatically tune the intrinsic frequency of the oscillators to the resonant frequency of a compliant quadruped robot The tuning goes beyond simple synchronization and the learned frequency stays in the controller when the robot is put to halt. The controller is model free, robust and simple. Results are presented illustrating how the controller can robustly tune itself to the robot, as well as readapt when the mass of the robot is changed. We also provide an analysis of the convergence of the frequency adaptation for a linearized plant, and show how that analysis is useful for determining which type of sensory feedback must be used for stable convergence. This approach is expected to explain some aspects of developmental processes in biological and artificial adaptive systems that "develop" through the embodied system-environment interactions. © 2006 IEEE.

Self-stabilization and behavioral diversity of embodied adaptive locomotion

Locomotion is of fundamental importance in understanding adaptive behavior. In this paper we present two case studies of robot locomotion that demonstrate how higher level of behavioral diversity can be achieved while observing the principle of cheap design. More precisely, it is shown that, by exploiting the dynamics of the system-environment interaction, very simple controllers can be designed which is essential to achieve rapid locomotion. Special consideration must be given to the choice of body materials. We conclude with some speculation about the importance of locomotion for understanding cognition. © Springer-Verlag Berlin Heidelberg 2004.

Compensatory growth response in three-spined stickleback in relation to feed-deprivation protocols

Different protocols of food deprivation were used to bring two groups of juvenile three-spined sticklebacks Gaslerosteus aculeatus to the same reduced body mass in comparison with a control group fed daily ad libitum. One group experienced I week or deprivation then 2 weeks on maintenance rations. The second group experienced I week of ad lithium feeding followed by 2 weeks of deprivation. The deprived groups were reduced to a mean mass ore. 80% of controls. The compensatory growth response shown when ad libitum feeding was resumed was independent of the trajectory by which the three-spined sticklebacks had reached the reduced body mass. The compensatory response was Sufficient to return the deprived groups to the mass and length trajectories shown by the control group within 4 weeks. There was full compensation for dry mass and total lipid, but incomplete compensation for lipid-free dry mass. Hyperphagia and increased growth efficiency were present in the re-feeding phase, but there was a lag of a week before the hyperphagia was established. The consistency of the compensatory response of immature three-spined sticklebacks provides a potential model system for the analysis and prediction of appetite and growth in teleosts. (C) 2003 The Fisheries Society of the British isles.

Comparison of compensatory growth responses of juvenile three-spined stickleback and minnow following similar food deprivation protocols

The compensatory growth responses of individual juveniles of two co-existing species were compared after identical periods of starvation to determine inter-specific similarities and differences. The carnivorous stickleback Gasterosteus aculeatus was compared with the omnivorous minnow Phoxinus phoxinus. Both species experienced 1 or 2 weeks of starvation before being re-fed ad libitum. The two species differed in their response to the starvation periods, with minnows showing a lower weight-specific loss. Both species showed compensatory responses in appetite, growth and to a lesser extent, growth efficiency. Minnows wholly compensated for 1 and 2 weeks of starvation. At the end of the experiment, sticklebacks starved For 2 weeks were still showing a compensatory response and had nut achieved full compensation. The compensatory responses of the sticklebacks showed a lag of a week before developing in the re-feeding phase, whereas the response of the minnows was immediate. Analysis of lipid and dry matter concentrations suggested that the compensatory response restored reserve lipids while also bringing the fish back to the growth trajectory of continuously fed fish. (C) 2001 The Fisheries Society of the British Isles.

An adaptive controller for a class of nonlinear system using direction basis function

For a class of nonlinear dynamical systems, the adaptive controllers are investigated using direction basis function (DBF) in this paper. Based on the criterion of Lyapunov' stability, DBF is designed which guarantees that the output of the controlled system asymptotically tracks the reference signals. Finally, the simulation shows the good tracking effectiveness of the adaptive controller.

两类模糊PID控制器的等价性分析

变论域与变分布模糊PID控制器是两类不同的自适应模糊控制器 ,分别通过调整转换因子与隶属函数分布对模糊控制器的性能进行调节。利用模糊控制器结构分析方法对这两类模糊PID控制器的本质进行了深入分析。通过分析可以得出结论 ,在一定条件下这两类模糊PID控制器在性能调节方面是等价的。此结论将对这两种模糊PID控制器的应用提供参考

Harmonic mode-locked ytterbium-doped fibre ring laser

We demonstrate a harmonic mode-locked ytterbium-doped fibre ring laser, which consists of a polarization-sensitive isolator, two polarization controllers, two 976 nm laser diodes as the pump source and a two-segment ytterbium-doped fibre. Utilizing an additive pulse mode-locked technique based on nonlinear polarization evolution, the ytterbium-doped fibre laser can operate in mode-locked state by adjusting the position of polarization controllers. The cavity fundamental repetition rate is 23.78 MHz. We also observe the second- and third-harmonic mode locking in the normal dispersion region, and their repetition rates are 47.66 MHz and 71.56 MHz, respectively. Over-driving of the saturable absorber in the harmonic mode-locking pulse is analysed and discussed in detail.

陕西省水蚀土壤因子指标插值方法比较研究

基于地统计学原理和半变异理论,采用地理信息系统技术定量研究了陕西省水蚀土壤因子指标的空间变异特征。分析比较了反距离权重法、样条函数法与普通克吕格法对陕西省土壤因子指标空间插值的精度。结果表明,研究区土壤抗冲系数具有中等强度的空间相关性,块金系数为32.29%,而稳渗速率、崩解速率、抗剪强度均表现为强烈的空间相关性,块金系数分别为13.19%,11.61%和12.98%。综合考虑平均相对误差、均方差及插值效果,认为普通克吕格法最好,更能反映土壤参数的空间特征并符合区域水土流失模型对数据的要求。对于普通克吕格法,稳渗速率的Lag步长为30 000 m,半方差理论模型为指数模型;抗冲系数、崩解速率、抗剪强度的Lag步长为55 000,半方差理论模型均为高斯模型。在空间分布上,各指标随土壤类型由北到南呈现明显的地带性规律。

Tunable and switchable multiwavelength fiber lasers with broadband range based on nonlinear polarization rotation technique

Switchable multiwavelength fiber laser outputs with a wide tuning range are experimentally observed in an ultralong cavity. Because of the long spooled single-mode fiber and filter effect of the cavity, multiwavelength lasers with the spacing of similar to 14.5 nm are obtained. The proposed fiber laser has the capacity of simultaneously emitting the three wavelengths. By means of adjusting the polarization controllers, the arbitrary single- and dual-wavelength operations are achieved in our laser. (C) 2010 Society of Photo-Optical Instrumentation Engineers. [DOI: 10.1117/1.3485754]

川西亚高山针叶林主要针叶树种年轮生态学研究

米亚罗地区是四川西部较为典型的亚高山针叶林区域之一。为建立该地区主要针叶树种岷江冷杉、云杉、紫果云杉和红杉的年轮宽度年表资料，了解不同海拔高度岷江冷杉原始林和不同恢复过程的人工针叶林及次生混交林树木径向生长规律，结合样地调查，用生长锥钻取了树木芯样做年轮生态学分析。芯样经过标准化程序固定和打磨抛光后，用WinDENDRO图像分析系统测量年轮宽度序列，用COFECHA程序交叉定年和控制测量数据质量，用ARSTAN程序建立了4个主要针叶树种的地区年表和不同海拔高度岷江冷杉林及人工针叶林和次生混交林针叶树的样地年表。 4个主要针叶树种年轮宽度年表的平均敏感度低于0.2，而其晚材宽度年表都具相对较高的平均敏感度。早材宽度与年轮总宽度标准化年表间的相关系数均在0.9以上；晚材宽度与年轮总宽度标准化年表间的相关系数则种间差异较大，红杉的最高，岷江冷杉的最低。岷江冷杉晚材宽度与年轮总宽度的相关性从1970年以后明显下降，而其他种的相关系数则随时间变化较小。树种之间标准化年表显著正相关，而云杉与紫果云杉和红杉与岷江冷杉之间相关系数明显较高。年表序列的第1主分量表达了4个树种树木共同径向生长变化格局；第2至第4主分量分别表达了云杉属和冷杉属、常绿针叶树种和落叶针叶树种以及云杉和紫果云杉树木径向生长变化差异。 不同海拔高度的8个岷江冷杉样地年轮宽度年表序列敏感度大体上随海拔高度升高而降低。各样地早材宽度与年轮总宽度年表之间的相关系数均在0.9以上，且随海拔高度变化不大；晚材宽度与年轮总宽度之间的相关系数随海拔高度的变化较大，并有随海拔升高而降低的趋势。样地年表序列之间相关系数差异很大，高海拔样地年表间多为显著正相关；低海拔样地年表间的相关系数变化不一；高海拔和低海拔样地年表之间相关性较差，且多不显著。样地年表的第1主分量能解释年表序列总方差的37.5%，反映了不同海拔高度岷江冷杉林木共同的径向生长变化格局；第2和第3主分量分别解释总方差的24.5%和18.2%，表现出明显的高海拔和低海拔样地树木间不同的径向生长变化，除一些样地例外，它们一般与低海拔样地年表有正相关，与高海拔样地年表有负相关。在那些另外的样地，海拔以外的其他因素可能也影响了树木径向生长变化。不同海拔高度样地林木的生长抑制和生长释放频率在不同时期表现出较大的差异，表明了不同的干扰历史和林木补充时间。 人工针叶林和次生混交林各样地林木早材宽度与其年轮总宽度年表之间相关系数均高达0.9以上；晚材宽度与年轮总宽度年表之间也都显著正相关，但人工针叶林样地的明显较高。样地年表序列之间的相关关系表现为，林分起源和经营管理相似的样地年表之间的相关系数明显较高，如人工针叶林与人工针叶林尽管树种不同，但样地年表之间显著正相关，而与次生混交林样地年表间关系不显著；反之亦然。综合比较各项生长参数及不同时期的树木径向生长速率，人工针叶林树木的胸径增长至少在40年以内是优于次生混交林的同种（或不同种）针叶树的。不同样地林木生长释放和生长抑制及人工针叶林树木胸高断面积增长分析表明，除严重的人为干扰外，林分郁闭后林木密度过大是造成高频率生长抑制的主要原因，在林分发育的适当时期通过抚育间伐等措施调控林分密度，是保证林木胸高断面积在一定时期内保持较高的连年增长的关键。日本落叶松作为引进的树种，在海拔3100 m左右种植表现良好，近30年来各项生长指标均高于林龄相近的云杉人工林，因此，适当用其作为川西亚高山针叶林采伐迹地快速恢复是合理的。 Miyaluo area is one of the typical regions covered by subalpine coniferous forests in western Sichuan province of southwestern China. To develop the regional tree-ring width chronology series for the dominant conifers such as Abies faxoniana, Picea asperata, P. purpurea and Larix potaninii, and to understand the radial growth patterns of conifers in Abies faxoniana natural forest stands at different altitudes, and in coniferous plantations and natural regenerated mixed stands in their different restoring processes as well, increment cores were sampled in the field together with conventional plots investigations for dendroecological analyses. After the increment cores being prepared according to standard procedures, the ring widths (total-ring and intra-ring widths) were measured with a WinDENDRO image-analysis system, and the measured tree-ring sequences were crossdated and quality-controlled with the software COFECHA. Using the software ARSTAN, we developed tree-ring width based chronology series of the four dominant conifers, eight site-specific Abies faxoniana chronologies, and seven site-specific chronologies of conifers in coniferous plantations and natural regenerated mixed stands. Mean sensitivities for total ring width chronologies of the four sampled dominant conifers were all below 0.2, while those for the latewood width chronologies of the same species were relatively much higher. Correlation coefficients between standard earlywood and total ring width chronologies of the four conifers were all above 0.9, but those between standard latewood and total ring width chronologies exhibited differences among species, with the coefficient of Larix potaninii the highest and that of Abies faxoniana the lowest. Correlation coefficients between latewood and total ring width of A. faxoniana obviously decreased from 1920-1970 for successive 50-year segments with 10-years lag analyses, though the same for the other three species changed unnoticeably with time. Tree-ring standard chronologies among species showed significant positive correlations, with the correlation coefficients between chronologies of Picea asperata and P. purpurea, and of Larix potaninii and Abies faxoniana relatively much higher. The first principal component of tree-ring chronologies represented the common radial growth patterns of the four conifers in Miyaluo area. The second, third and fourth PCs expressed the differences in radial growth responses for the genus Picea and Abies, for the evergreen and deciduous confers, and for the two species of the genus Picea, respectively. In general, mean sensitivities of the eight Abies faxoniana site-specific tree-ring width chronologies decreased with increasing altitude. The correlation coefficients between earlywood and total ring width chronologies for all sites reached 0.9, which did not change much with altitude; but those between latewood and total ring width chronologies diversified, with a decreasing tendency from lower altitudinal sites to higher altitudinal sites. Correlation coefficients among site chronologies varied considerably, with significant positive correlations among higher site chronologies, mixed results among lower site chronologies, and poor and insignificant correlations between chronologies of higher site and lower site. The first PC, which represents 37.5% of the total variance, reflected a common radial growth response at sites of different altitudes, and it showed a tendency of explaining more variance with increasing altitude. The second and the third PCs contributed to 24.5% and 18.2% of the total variance, respectively, exhibiting distinctive differences in radial growth responses between low- and high-altitudinal sites. With some exceptions, the radial growth represented by the second and third PCs had a positive correlation with that at the low-altitudinal sites and a negative correlation with that at the high-altitudinal sites. For those exceptional sites, factors other than altitude might also play a role in affecting tree-ring growth variations. Trees in stands of different altitudes showed great differences in frequencies of growth suppressions and releases through times, suggesting different disturbance histories and periods when trees recruiting to the canopy. Correlation coefficients between earlywood and total ring width chronologies for all sites of coniferous plantations and natural regenerated mixed stands were also above 0.9; and the same between latewood width and total ring width chronologies all positively correlated, too, with the coefficients of the coniferous plantations obviously much higher. Correlations among site chronologies showed that the coefficients among sites with similar stand origin and management regimes were much higher than those among sites with different stand origin and management regimes. For example, significant positive correlations were found for chronologies among different coniferous plantations, irrespective of species differences; while insignificant correlations between chronologies of the same conifer from a coniferous plantation and a natural regenerated mixed stand, and vise versa. Integrative comparisons of different tree growth parameters and radial growth rates at different stages indicated that the diameter at breast height (DBH) increments for trees in coniferous plantations were faster than those for trees of the same (or different) species in the natural regenerated mixed stands, at least within their first 40 years of stand development. Analyses of growth releases and suppressions, and basal area increments of trees in different stands demonstrated that over-dense individuals after canopy closure was the main factor resulting in high frequencies of radial growth suppressions, with some exceptions of severe man-made disturbances. Therefore, to ensure a continuous basal area current annual increment in certain periods, tree density controlling through thinning in due time during the stand development process are necessary. It should be mentioned that, as an introduced conifer to Miyaluo area, Larix kaempferi grew quite well at altitude of ca. 3100 m after planting in 1970s. In their near 30 years of stand development, Larix kaempferi trees exhibited faster growth in various parameters than Picea asperata trees of the similar stand age did. Thus we think it reasonable to use Larix kaempferi as a fast restoring species at appropriate sites of cutting blanks of subalpine coniferous forests in western Sichuan.

厌氧产氢菌的分离筛选、诱变选育及其产氢特性的研究

本文从四川绵竹酒厂、成都市龙泉长安垃圾填埋场以及四川大学荷花池底的厌氧污泥中先后分离得到63株厌氧产氢菌，其中H-8、H-61、HC-10等16株产氢细菌产氢能力较高，HC-10的产氢能力最高，最大产氢量和最大产氢速率分别达到2840 ml H2/L培养基和25.39 mmol H2/g drycell·h，对HC-10进行生理生化鉴定和分子生物学鉴定，判定其为clostridium sp.，对HC-10的产氢条件进行了研究，结果表明，该菌的最适生长温度为35 ℃，最适生长初始pH为7，以葡萄糖为最佳碳源，以蛋白胨为最佳氮源，不利用无机氮源，其产氢发酵液相产物以乙醇和乙酸为主，其发酵类型属于乙醇型发酵。此外，以酒糟废液作为底物，进行了菌株HC-10的生物强化试验，研究表明，投加了HC-10的强化系统其产氢量比对照高出40.32%。 同时为了获得厌氧产氢菌的高效突变株，分别以产氢菌H-8和H-61为原始菌株进行微波诱变处理，对微波诱变参数进行了优化，考察了突变株的遗传稳定性、产氢特性及耐酸性。菌株H-8经过微波诱变得到5株高产氢突变株HW7、HW33、HW181、HW184、HW195，经多次传代表明HW195是稳定的高产突变株。突变株HW195具有较好的耐酸性，在pH值为2.8时仍能生长。通过间歇发酵实验，其最大产氢量和最大产氢速率分别达到2460 mL/L培养基和27.97 mmol H2/g drycell·h，比原始菌分别提高了50.75%和41.7%。菌株H-61经过微波诱变后选育得到的突变株HW-18，其最大产氢量和最大产氢速率分别达到2190 mL/L培养基和25.86 mmol H2/g drycell·h，比原始菌分别提高了23.03%和31.00%。 为了对比各种诱变方式对产氢菌产氢能力的影响，以厌氧产氢菌H-61为原始菌株，先后经亚硝基胍(NTG)、紫外(UV)诱变，选育得到1株高产突变株HCM-23。在葡萄糖浓度为10 g/L的条件下，其产氢量为3024 mL/L培养基，比原始菌株提高了69.89%；其最大产氢速率为33.19 mmol H2/g drycell·h，比原始菌株提高了68.14%。经过多次传代实验，稳定性良好。其发酵末端产物以乙醇和乙酸为主，属于典型乙醇型发酵。其最适产氢初始pH为6.5，最适生长温度为36 ℃，以蔗糖为最佳碳源。与原始菌株相比，突变株HCM-23的产氢特性发生了改变，如生长延滞期延长，可利用无机氮源等。 From anaerobic activated sludge, 16 strains of hydrogen producing bacteria were newly isolated. One of them named as HC-10 had the highest hydrogen producing capability, under the batch fermentative hydrogen production condition, the maximal hydrogen yield and hydrogen production rate was 2840 mL/L culture and 25.39 mmol H2/g drycell·h. It was identified as clostridium sp.HC-10 by 16S rDNA sequence analysis. Various parameters for hydrogen production, including substrates, initial pH and temperature, have been studied. The optimum condition for hydrogen producing of strain HC-10 were achieved as: initial pH 7.0, temperature 35 ℃, glucose as the favorite substrate, Moreover, using distiller's solubles wastewater as substrate, HC-10 strain was added in the biohydrogen producing system to research the bioaugmentation effection. The results showed that the hydrogen production of bioaugmentation system was 40.32% higher than the noaugmentation system. An anaerobic, hydrogen producing strain H-8 was irradiated by microwave to optimize the microwave mutagenesis condition, and to test the heredity, hydrogen-producing potential and aciduric of the mutants. An aciduric mutant named as HW195 with steady hydrogen-producing capability was obtained, which can grow at pH 2.8. Its capability of hydrogen production was tested in the batch culture experiments. The maximum hydrogen yield and hydrogen production rate was 2460 mL/L culture and 29.97 mmol H2/g drycell·h, which was 50.7% and 41.7% higher than those of the initial strain, respectively. When used the strain H-61 as original strain, a mutant named as HW18 was obtained. The maximum hydrogen yield and hydrogen production rate was 2190 mL/L culture and 25.86 mmol H2/g drycell·h, which was 23.03% and 31.00% higher than those of the initial strain, respectively. The results demonstrated that microwave mutagenesis could be used in the field of hydrogen producing microorganism. The hydrogen producing strain H-61 was used as an original strain which was induced by NTG and UV for increasing and the hydrogen production capability. One of the highest efficient H2-producing mutants was named as HCM-23 with its stable hydrogen production capability. which was tested in the batch culture experiments. With the condition of 10 g/L glucose, its cumulative hydrogen yield and hydrogen production rate was 3024 mL/L culture and 33.19 mmol H2/g drycell·h, 69.89％and 68.14％ higher than that of the original strain, respectively. The terminal liquid product compositions showed that the mutant HCM-23 fermentation was ethanol type, while the original strain H-61 fermentation was butyric acid type. Varieties of parameters of hydrogen production fermentation were studied, including time, carbon source, nitrogen source, glucose concentration, glucose utilization, initial pH and incubation temperature had been studied, indicated the optimum condition of hydrogen production for the mutant HCM-23 as initial pH6.5, temperature 36 ℃, and the favorite substrate was sucrose. The hydrogen production characters of the mutant and the original strain were different, such as, the growth lag phase and the utilization of inorganic nitrogen source, etc. This work shows a good application potential of NTG-UV combined mutation in the biohydrogen production. And the hydrogen production mechanism and metabolic pathway should be explored furthermore.