A method for Ca, Fe, Ga, Na, Si and Zn determination in alumina by inductively coupled plasma optical emission spectrometry after aluminum precipitation

In this present work a method for the determination of Ca, Fe, Ga, Na, Si and Zn in alumina (Al(2)O(3)) by inductively coupled plasma optical emission spectrometry (ICP OES) with axial viewing is presented. Preliminary studies revealed intense aluminum spectral interference over the majority of elements and reaction between aluminum and quartz to form aluminosilicate, reducing drastically the lifetime of the torch. To overcome these problems alumina samples (250 mg) were dissolved with 5 mL HCl + 1.5 mLH(2)SO(4) + 1.5 mL H(2)O in a microwave oven. After complete dissolution the volume was completed to 20 mL and aluminum was precipitated as Al(OH)(3) with NH(3) (by bubbling NH(3) into the solution up to a pH similar to 8, for 10 min). The use of internal standards (Fe/Be, Ga/Dy, Zn/In and Na/Sc) was essential to obtain precise and accurate results. The reliability of the proposed method was checked by analysis of alumina certified reference material (Alumina Reduction Grade-699, NIST). The found concentrations (0.037%w(-1) CaO, 0.013% w w(-1) Fe(2)O(3), 0.012%w w(-1)Ga(2)O(3), 0.49% w w(-1) Na(2)O, 0.014% w w(-1) SiO(2) and 0.013% w w(-1) ZnO) presented no statistical differences compared to the certified values at a 95% confidence level. (C) 2011 Elsevier B.V. All rights reserved.

Application of 1-Allyl-3-(1-butyl)imidazolium Chloride in the Synthesis of Cellulose Esters: Properties of the Ionic Liquid, and Comparison with Other Solvents

The ionic liquid (IL), 1-allyl-3-(1-butyl)imidazolium chloride (AlBuImCl), has been synthesized and its properties determined. Increase in the temperature increased its conductivity and decreased its density, polarity, and viscosity. Microcrystalline cellulose (MCC), dissolves in thisIL by heating at 80 degrees C; this did not affect its degree of polymerization, decreased its index of crystallinity (Ic), and changed in morphology after regeneration. Convenient acylation of MCC was achieved by using 50% excess anhydride at 80 degrees C, for 24 or 48 h for acetic and butyric anhydride, respectively. The composition of the mixed esters depended on the initial ratio of the anhydrides, and their order of addition.

Micellar properties of surface active ionic liquids: A comparison of 1-hexadecyl-3-methylimidazolium chloride with structurally related cationic surfactants

Ionic liquids, ILs, carrying long-chain alkyl groups are surface active, SAIIs. We investigated the micellar properties of the SAIL 1-hexadecyl-3-methylimidazolium chloride, C(16)MeImCl, and compared the data with 1-hexadecylpyridinium chloride, C(16)PYCl, and benzyl (3-hexadecanoylaminoethyl)dimethylammonium chloride, C(15)AEtBzMe(2)Cl. The properties compared include critical micelle concentration, cmc; thermodynamic parameters of micellization; empirical polarity and water concentrations in the interfacial regions. In the temperature range from 15 to 75 degrees C, the order of cmc in H(2)O and in D(2)O is C(16)PYCl > C(16)MeImCl > C(15)AEtBzMe(2)Cl. The enthalpies of micellization, Delta H(mic)(degrees), were calculated indirectly from by use of the van`t Hoff treatment; directly by isothermal titration calorimetry, ITC. Calculation of the degree of counter-ion dissociation, alpha(mic), from conductivity measurements, by use of Evans equation requires knowledge of the aggregation numbers, N(agg), at different temperatures. We have introduced a reliable method for carrying out this calculation, based on the volume and length of the monomer, and the dependence of N(agg) on temperature. The N(agg) calculated for C(16)PyCl and C(16)MeImCl were corroborated by light scattering measurements. Conductivity- and ITC-based Delta H(mic)(degrees) do not agree; reasons for this discrepancy are discussed. Micelle formation is entropy driven: at all studied temperatures for C(16)MeImCl; only up to 65 degrees C for C(16)PyCl; and up to 55 degrees C for C(15)AEtBzMe(2)Cl. All these data can be rationalized by considering hydrogen-bonding between the head-ions of the monomers in the micellar aggregate. The empirical polarities and concentrations of interfacial water were found to be independent of the nature of the head-group. (C) 2010 Elsevier Inc. All rights reserved.

Quantification of N-acetylcysteine in pharmaceuticals using cobalt phthalocyanine modified graphite electrodes

Flow injection analysis (FIA) with amperometric detection was employed for the quantification of N-acetylcysteine (NAC) in pharmaceutical formulations, utilizing an ordinary pyrolytic graphite (OPG) electrode modified with cobalt phthalocyanine (CoPc). Cyclic voltammetry was used in preliminary studies to establish the best conditions for NAC analysis. In FIA-amperometric experiments the OPG-CoPc electrode exhibited sharp and reproducible current peaks over a wide linear working range (5.0 x 10(-5)-1.0 x 10(-3) mol L(-1)) in 0.1 mol L(-1) NaOH solution. High sensitivity (130 mA mol(-1) cm(2)) and a low detection limit (9.0 x 10(-7) mol L(-1)) were achieved using the sensor. The repeatability (R.S.D.%) for 13 successive flow injections of a solution containing 5.0 x 10(-4) mol L(-1) NAC was 1.1%. The new procedure was applied in analyses of commercial pharmaceutical products and the results were in excellent agreement with those obtained using the official titrimetric method. The proposed amperometric method is highly suitable for quality control analyses of NAC in pharmaceuticals since it is rapid, precise and requires much less work than the recommended titrimetric method. (C) 2010 Elsevier B.V. All rights reserved.

Electrocatalytic behavior of glassy carbon electrodes modified with multiwalled carbon nanotubes and cobalt phthalocyanine for selective analysis of dopamine in presence of ascorbic acid

This work describes the development, electrochemical characterization and utilization of a cobalt phthalocyanine modified carbon nanotube electrode for the quantitative determination of dopamine in 0.2 mol L-1 phosphate buffer contaminated with high concentration of ascorbic acid. The electrode surface was analyzed by cyclic voltammetry and electrochemical impedance spectroscopy which showed a modified surface presenting a charge transfer resistance of 500 Omega, against the 16.46 k Omega value found for the bare glassy carbon surface. A pseudo rate constant value of 5.4 x 10(-4) cm s(-1) for dopamine oxidation was calculated. Voltammetric experiments showed a shift of the peak potential of DA oxidation to less positive value at 390 mV as compared with that of a bare GC electrode at 570 mV. The electrochemical determination of dopamine, in presence of ascorbic acid in concentrations up to 0.1 mol L-1 by differential pulse voltarnmetry, yielded a detection limit as low as 2.56 x 10(-7) mol L-1.

Determination of epinephrine in urine using multi-walled carbon nanotube modified with cobalt phthalocyanine in a paraffin composite electrode

This paper describes the development, electrochemical characterization and utilization of a cobalt phthalocyanine (CoPc), modified multi-walled carbon nanotube (MWCNT), and paraffin composite electrode for the quantitative determination of epinephrine (EP) in human urine samples. The electrochemical profile of the proposed composite electrode was analyzed by differential pulse voltammetry (DPV) that showed a shift of the oxidation peak potential of EP at 175 mV to less positive value, compared with a paraffin/graphite composite electrode without CoPc. DPV experiments in PBS at pH 6.0 were performed to determine EP without any previous step of extraction, clean-up, and derivatization, in the range from 1.33 to 5.50 mu mol L(-1), with a detection limit of 15.6 nmol L(-1) (2.86) of EP in electrolyte prepared with purified water. The lifetime of the proposed sensors was at least over 1000 determinations with 1.7 and 3.1 repeatability and reproducibility relative standard deviations, respectively. Human urine samples without any purification step were successfully analyzed under the standard addition method using paraffin/MWCNT/CoPc composite electrode. (C) 2010 Elsevier B.V. All rights reserved.

Direct Electrochemical Determination of Glyphosate at Copper Phthalocyanine/Multiwalled Carbon Nanotube Film Electrodes

A copper phthalocyanine/multiwalled carbon nanotube film-modified glassy carbon electrode has been used for the determination of the herbicide glyphosate (Gly) at -50 mV vs. SCE by electrochemical oxidation using differential pulse voltamtnetry (DPV). Cyclic voltammetry and electrochemical impedance spectroscopy showed that Gly is adsorbed on the metallic centre of the copper phthalocyanine molecule, with formation of Gly-copper ion complexes. An analytical method was developed using DPV in pH 7.4 phosphate buffer solution, without any pretreatment steps: Gly was determined in the concentration range of 0.83-9.90 mu mol L(-1), with detection limit 12.2 nmol L(-1) (2.02 mu g L(-1))

Anticorrosive cerium-based coatings prepared by the sol-gel method

The development of efficient anti-corrosion and environmentally friendly coating systems are needed for the replacement of the highly toxic Cr-based conversion coatings for corrosion protection of aluminum alloys. In this study, we demonstrate that the direct application of ceramic cerium-based sol-gel coatings to AA7075-T6 substrates produces high-performance anti-corrosion layers. Electrochemical experiments and analyses of the microstructure demonstrate that the protective layers are very efficient for the passivation of the alloy surfaces operating as both passive and active barrier for corrosion protection.

Varmsmidning av aluminiumlegering 6026 T9 : Warm forging of aluminum alloy 6026 T9

In this project forging of aluminum alloy Al 6026 T9 has been performed in the temperature range of 400 °C – 470 °C. The alloy which was in the shape of a cylindrical billet was formed in a press with the aim of analyzing the effect of different forging temperatures and required press load for optimal die filling. The component’s dimensions were later measured and compared to a reference piece. To ease the flow of material a lubricant was used between the billet and the die. This was demonstrated by compressing the billet with and without any lubricant.The performed experiments show that the lubricant reduces friction and makes it easier for the material to flow into the die. Higher billet temperature than 450 °C is deemed unnecessary as it does not give any significant improvement in filling the die. The experiments also conclude that a press load of at least 280 tons is required for these conditions.

Solubilizacao e interacao de pigmentos com solventes organicos e agentes tenso-ativos

A Mg e Mn-Ftalocianina (Mg e Mn-Pc) foram solubilizados à 25°C em dimetilsulfóxido (DMSO); N, N-dimetilacetamida (DMA); N,N-dimetilformamida (DMF); N-metil-formamida, formamida, piridina, o-diclorobenzeno, monoclorobenzeno, tolueno, metanol, etanol, propanol-1, propanol-2, butanol-1 e octanol-1. Alguns valores representativos obtidos para o logarítimo da absortividade molar (E) da Mn-Pc, são os seguintes: o-diclorobenzeno (E = 4,94); DMSO (E = 4,39); octanol-1 (E = 3,90). Valores correspondentes para Mg-Pc são: o-diclarobenzeno (E = 4,93); DMSO (E = 5,22) e Octanol-1 ( E = 5,06). Em função de interação com solventes, pode-se classificar a Mg-Pc como um indicador básico e a Mn-Pc como indicador ácido. Os pigmentos Mg e Mn-Pc foram também solubillzados em soluções aquosas contendo vários surfatantes à 25°C. A Mg-Pc apresentou solubilidade significativa em água contendo brometo de cetiltrimetilamônio (CTAB), Brij-35, cloreto de cetilpiridinio (CPC1), brometo de cetilpiridínio (CPBr,) Triton X-100, cloreto de metildodecilbenziltrimetilamônio, brometo de cetildimetiletilamõnio e brometo de laurilisoquinolínio. A Mn-Pc foi solúvel em soluções aquosas de Brij-35 e Triton X-100. Em função de sua interação com surfatantes a Mg-Pc é classificada como corante catiônico e a Mn-Pc como corante aniônico. O corante comercial quinóide Oil Blue A [1,4-di(isopropilarnina)-antraquinona - 9,10 foi solubilizado à 25°C em DMF, DMSO, DMA, monoclorobenzeno, benzeno, tolueno, piridina, metanol, etanol, propanol-1, propanol-2, butanol-1 e octanol-1. Foi também solubilizado em soluções aquosas de surfatantes, tais como sódio lauril-sulfato (NaLS), cloreto de cetiltrimetilamônio (CTAB), brometo de cetildimetiletilamônio, Triton X-100, cloreto de cetilpiridínio (CPCl), Brij-35, cloreto de rnetildodecilbenziltrimetilamônio e brometo de laurilisoquinolínio. Em função de suas interações com os solventes o corante é um indicador ácido-básico pouco sensível e em função de sua interação com surfatantes é um corante catiônico. 0s resultados experimentais apresentam importância teórica e prática considerando sistemas que envolvem armazenamento e transferência de energia, compostos porfirínicos, fotossíntese, fotocondutores, coletores solares, semi-condutores e processos de embelezamento e proteção de superficies de vários materiais.

Aplicação de técnicas eletroquímicas na determinação do potencial de corrosividade de ligas de alumínio em água produzida

The resistance of aluminum and their alloys, to the corrosion phenomenon, in aqueous solutions, is a result of the oxide layer formed. However, the corrosion process in the aluminum alloy is associated with the presence a second phase of particles or the presence of chloride ions which promote the disruption of the oxide layer located producing the corrosion process. On the other hand, the term water produced is used to describe the water after the separation of the oil and gas in API separators. The volumes of produced water arrive around 5 more times to the volume of oil produced. The greatest feature of the water is the presence of numerous pollutants. Due to the increased volume of waste around the world in the current decade, the outcome and the effect of the discharge of produced water on the environment has recently become an important issue of environmental concern where numerous treatments are aimed at reducing these contaminants before disposal. Then, this study aims to investigate the electrochemical corrosion behavior of aluminum alloy 6060 in presence of water produced and the influence of organic components as well as chloride ions, by using the electrochemical techniques of linear polarization. The modification of the passive layer and the likely breakpoints were observed by atomic force microscopy (AFM). In the pit formation potential around -0.4 to -0.8 V/EAg/AgCl was observed that the diffusion of chloride ions occurs via the layer formed with the probable formation of pits. Whereas, at temperatures above 65 °C, it was observed that the range of potential for thepit formation was -0.4 to -0.5 V/EAg/AgCl. In all reactions, the concentration of Al(OH)3 in the form of a gel was observed

Sodium chloride added to transport water and physiological responses of Matrinxã Brycon amazonicus (Teleost: Characidae)

A adição de sal à água tem sido utilizada para a mitigação de estresse e aumento da taxa de sobrevivência em peixes. O presente estudo avaliou o efeito do cloreto de sódio (0,0; 1,0; 3,0 e 6.0 g/l) nas concentrações de cortisol plasmático, glicemia, triglicerídios, proteínas total plasmática, hematócrito, hemoglobina, número de eritrócitos, glicogênio e lipídio hepáticos, e lipídio muscular em matrinxã Brycon amazonicum adultos após quatro horas de transporte e durante período de recuperação de 96 h. Amostras foram coletadas antes e depois do transporte, bem como 24 e 96 h após a chegada. O nível de cortisol plasmático estava mais elevado logo após o transporte quando comparado à condição inicial (pré-transporte), exceto para os peixes transportados com sal nas concentrações 3,0 e 6,0 g/l. Comportamento semelhante foi observado para a glicemia, porém os peixes dos tratamentos 0,0, 1,0 e 3,0 g/l necessitaram de período superior a 24 h para recuperar a condição inicial. Foram registrados níveis mais baixos de glicogênio hepático em peixes do tratamento controle (0,0 g/l). Os parâmetros hemoglobina, número de eritrócitos, proteína plasmática total e lipídio hepático não apresentaram alterações durante o período experimental. Os valores de hematócrito diminuíram logo após o transporte em todos os tratamentos, retornando aos níveis iniciais após 24 h. Todos os tratamentos apresentaram redução nos níveis de lipídio muscular e triglicerídios durante o período de recuperação. Os resultados sugerem que a adição de 6,0 g/l de sal na água de transporte reduz as alterações fisiológicas de estresse e que é necessário período de 96 h após o transporte para a recuperação da condição inicial de matrinxãs transportados sem a adição de sal.

Fast and efficient synthesis of pyrano[3,2-c]quinolines catalyzed by niobium(V) chloride

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Aluminum tolerance on genotypes of signal grass

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Influence of the season of year, stage of lactation and milking time on the chloride content in bovine milk

From January to October 1995, chloride content determinations were accomplished in 2,218 samples of milk collected from 67 quarters of 17 lactating cows, in initial, middle and final stages of lactation, in the morning and afternoon milking. The highest means of chloride contents were observed among the milk samples collected in the final stage of lactation (0,203 gC1/100ml), in the summer (0,212 gC1/100ml) and in the morning milking (0,189 g C1/100ml). The differences observed between the chloride contents in the samples obtained in the different stages of lactation and the seasons of the year were statistically significant (P<0.0001). The gratest occornce of chloride at rates superior to 0.22 gC1100ml was observed in the final stge of lactation (31.4%), summer (44.2%) and after the morning milking (27.8%). These results evidentiate the influence of physiological and external factors (stage of lactation and season of the year) on the concentration of chloride of milk.