Use of Photovoltaic on an E-bike? : A Feasibility Study

In recent years the number of bicycles with e-motors has been increased steadily. Within the pedelec – bikes where an e-motor supports the pedaling – a special group of transportation bikes has developed. These bikes have storage boxes in addition to the basic parts of a bike. Due to the space available on top of those boxes it is possible to install a PV system to generate electricity which could be used to recharge the battery of the pedelec. Such a system would lead to grid independent charging of the battery and to the possibility of an increased range of motor support. The feasibility of such a PV system is investigated for a three wheeled pedelec delivered by the company BABBOE NORDIC.The measured data of the electricity generation of this mobile system is compared to the possible electricity generation of a stationary system.To measure the consumption of the pedelec different tracks are covered, and the energy which is necessary to recharge the bike battery is measured using an energy logger. This recharge energy is used as an indirect measure of the electricity consumption. A PV prototype system is installed on the bike. It is a simple PV stand alone system consisting of PV panel, charge controller with MPP tracker and a solar battery. This system has the task to generate as much electricity as possible. The produced PV current and voltage aremeasured and documented using a data logger. Afterwards the average PV power is calculated. To compare the produced electricity of the on-bike system to that of a stationary system, the irradiance on the latter is measured simultaneously. Due to partial shadings on the on-bike PV panel, which are caused by the driver and some other bike parts, the average power output during riding the bike is very low. It is too low to support the motor directly. In case of a similar installation as the PV prototype system and the intention always to park the bike on a sunny spot an on-bike system could generate electricity to at least partly recharge a bike battery during one day. The stationary PV system using the same PV panel could have produced between 1.25 and 8.1 times as much as the on-bike PV system. Even though the investigation is done for a very specific case it can be concluded that anon-bike PV system, using similar components as in the investigation, is not feasible to recharge the battery of a pedelec in an appropriate manner. The biggest barrier is that partial shadings on the PV panel, which can be hardly avoided during operation and parking, result in a significant reduction of generated electricity. Also the installation of the on-bike PV system would lead to increased weight of the whole bike and the need for space which is reducing the storage capacity. To use solar energy for recharging a bike battery an indirect way is giving better results. In this case a stationary PV stand alone system is used which is located in a sunny spot without shadings and adjusted to use the maximum available solar energy. The battery of the bike is charged using the corresponding charger and an inverter which provides AC power using the captured solar energy.

Adição de resíduo cerâmico em pastas geopoliméricas para cimentação de poços de petróleo

The development of activities the of oil and gas sector have promoted the search for suitable materials for cementing oil wells. In the state of the Rio Grande do Norte, the integrity of the cement sheath tends to be impaired during steam injection, a procedure necessary to increase oil recovery in reservoirs with low-viscosity oil. The geopolymer is a material that can be used as alternative cement, since it has been used in the production of fire-resistant components, building structures, and for the control of toxic or radioactive residues. Geopolymers result from condensation polymer alkali aluminosilicates and silicates resulting three-dimensional polymeric structures. They are produced in a manner different from that of Portland cement, which is made an activating solution that is mixed with geopolymer precursor. Among the few works studied allowed us to conclude that the pastes prepared with metakaolin as precursor showed better performance of its properties. Several studies show the addition of waste clay as a means of reducing cost and improving end of the folder properties. On this basis, the goal is to study the influence of the addition of ceramic waste in geopolymer paste. To develop the study of rheology tests were carried out, filtered, thickening time, compressive strength, free water, specific gravity and permeability, according to the American Pretoleum Institute (API). The results for all formulations studied show that the folders have high mechanical strength to a light paste; low filtrate volume, absence of free water, very low permeability, slurry, consistent with a light paste, and thickening time low that can be corrected with the use of a retardant handle. For morphological characterization, microstructural, physical, chemical and thermal tests were carried out by XRD, MEV, DTA, TG, FTIR. In the trial of XRD, it was found that geopolymer is an amorphous material, with a peak of crystalline kaolinite. In tests of TG / DTA, revealed the presence of a significant event, which represents the mass loss related to water, and also observed the reduction of weight loss by increasing the concentration of ceramic waste. In the trial of MEV, we found a uniform matrix without the presence of other phases. In the trial of FT-IR, we observed the presence of the band related to water. From all results it was determined that the optimum concentration range of use is between 2.5 and 5% of waste ceramic

Application of fuzzy logic for the evaluation of livestock slaughtering

A lógica fuzzy admite infinitos valores lógicos intermediários entre o falso e o verdadeiro. Com esse princípio, foi elaborado neste trabalho um sistema baseado em regras fuzzy, que indicam o índice de massa corporal de animais ruminantes com objetivo de obter o melhor momento para o abate. O sistema fuzzy desenvolvido teve como entradas as variáveis massa e altura, e a saída um novo índice de massa corporal, denominado Índice de Massa Corporal Fuzzy (IMC Fuzzy), que poderá servir como um sistema de detecção do momento de abate de bovinos, comparando-os entre si através das variáveis linguísticas )Muito BaixaM, ,BaixaB, ,MédiaM, ,AltaA e Muito AltaM. Para a demonstração e aplicação da utilização deste sistema fuzzy, foi feita uma análise de 147 vacas da raça Nelore, determinando os valores do IMC Fuzzy para cada animal e indicando a situação de massa corpórea de todo o rebanho. A validação realizada do sistema foi baseado em uma análise estatística, utilizando o coeficiente de correlação de Pearson 0,923, representando alta correlação positiva e indicando que o método proposto está adequado. Desta forma, o presente método possibilita a avaliação do rebanho, comparando cada animal do rebanho com seus pares do grupo, fornecendo desta forma um método quantitativo de tomada de decisão para o pecuarista. Também é possível concluir que o presente trabalho estabeleceu um método computacional baseado na lógica fuzzy capaz de imitar parte do raciocínio humano e interpretar o índice de massa corporal de qualquer tipo de espécie bovina e em qualquer região do País.

Eficácia do diquat no controle de Hydrilla verticillata, Egeria densa e Egeria najas e toxicidade aguda para o Guaru (Phallocerus caudimaculatus), em condições de laboratório

No Brasil, as macrófitas aquáticas submersas, Egeria densa e Egeria najas, têm causado prejuízos aos usos múltiplos da água. Hydrilla verticillata foi recentemente introduzida, mas tem histórico como planta problemática nos EUA, no México e na Austrália. O objetivo deste trabalho foi avaliar as suscetibilidades relativas dessas três macrófitas aquáticas ao diquat e os riscos da utilização desse herbicida para o guaru (Phallocerus caudimaculatus). Para isso, foram instalados ensaios em condições de laboratório, a fim de avaliar a suscetibilidade relativa das três macrófitas por meio da manutenção de ponteiros dessas plantas em soluções contendo 0,0; 0,2; 0,4; 0,8; e 1,6 mg L-1 de diquat (Reward®) por 14 dias. A avaliação foi realizada pela variação do acúmulo de matéria fresca e do comprimento dos ponteiros no período de exposição ao herbicida. H. verticillata mostrou maior sensibilidade ao diquat em comparação com as duas macrófitas do gênero Egeria, mesmo em baixas concentrações do herbicida. Nas maiores concentrações, E. densa mostrou maior sensibilidade que E. najas. O risco da aplicação do diquat para P. caudimaculatus foi estimado pela toxicidade aguda. Alevinos de P. caudimaculatus de 0,4 ± 0,2 mg foram expostos a soluções de 0,0; 1,0; 5,0; 10,0; 15,0; 20,0; 25,0; e 30,0 mg L-1 de diquat. A concentração letal de 50% (CL(I) (50;96h)) do diquat estimada para P. caudimaculatus foi de 7,17 mg L-1. Para P. caudimaculatus, a toxicidade aguda foi superior à concentração recomendada para o controle de macrófitas aquáticas submersas, indicando risco muito baixo para esse peixe.

Efeito do ácido alfa-lipóico sobre biomarcadores de estresse oxidativo, inflamação e fatores de risco cardiovascular em hipertensos

Alpha-lipoic acid (ALA) is a potent antioxidant with favourable anti-inflammatory, metabolic and endothelial effects, and has been widely investigated due to its potential against cardiovascular risk factors. This study aimed to evaluate the effect of oral ALA supplementation on oxidative stress biomarkers, inflammation and cardiovascular risk factors in patients with hypertension. This is a double-blind placebo-controlled randomized clinical trial, where the intervention was evaluated prospectively comparing results in both groups. The sample consisted of 64 hypertensive patients who were randomly distributed into ALA group (n = 32), receiving 600 mg / day ALA for twelve weeks and control group (n = 32), receiving placebo for the same period. The following parameters were evaluated before and after intervention: lipid peroxidation, content of reduced glutathione (GSH), enzymatic activities of glutathione peroxidase (GPx) and superoxide dismustase, ultrasensitive C-reactive protein (hs-CRP), triglycerides, total cholesterol and fractions, fasting glucose and anthropometric indicators. There was a statistically significant reduction (p <0.05) in serum concentrations of total cholesterol, very low density lipoprotein (VLDL), high density lipoprotein (HDL), triglycerides and blood glucose. There was a reduction in body weight and waist, abdominal and hip circumferences in the group that received ALA. In addition, there was a statistically significant increase (p <0.05) in the contents of reduced glutathione (GSH) and glutathione peroxidase (GPx) in the group receiving ALA. Oral administration of ALA appears to be a valuable adjuvant therapy, which may contribute to decrease the damage caused by oxidative stress and other risk factors associated with the atherosclerotic process

Modelagem e estimação de parâmetros genéticos e fenotípicos para pesos do nascimento à seleção (378 dias) de machos Nelore

Genetic parameters for weights (17, 942 records), obtained in intervals of 60 days, from the birth to selection (378 days of age), of 2,582 males of the Nellore breed was estimated in univariate analyses by the Maximum Restricted Likelihood method. The models of analysis models included the fixed effects of contemporary groups, month of birth, mother age and age when the weights were collected as covariate. Three models differing in random effects were tested: the model 1 (M1) was adjusted for the direct and maternal addictive genetic effects and maternal permanent environment; in model 2 (M2) the maternal genetic effect was excluded; and the model 3 (M3) was only adjusted for the direct addictive genetic effect. The test of likelihood (LRT) detected significant differences, for all the ages, of M2 and M1 in relation to the simple model (M3), evidencing the importance of the maternal effects. Except for the birth weight (0.40), low values (0.05 to 0.12) of h(2) were found for M1 and M2 until 8 months of age and, after this period, reasonable increase could be observed, reaching 0.28 until 13 months of age. The estimates of the total variance fraction, due to the effect of maternal permanent environment, were high and practically became unaffected between the models 1 and 2. Maternal effects, not necessarily decomposed (in genetic addictive and permanent environment), affected the Nellore males growth. Models that contemplate maternal effects, besides the genetic addictive direct effects, are more realistic to describe the trajectory of the variances in the initial phases of growth of Nelore male calves.

Results of 23 years of selection for post-weaning weight in a Caracu beef herd

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Genetic parameters and relationships between growth traits and scrotal circumference measured at different ages in Nellore cattle

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Desenvolvimento e análise de material compósito a base de penas de frango (fibras de queratina-KF) e matriz de poliéster insaturado

Use of natural fibres as a reinforcement material in the manufacture of composites show a series of advantages: availability, biodegradability, low weight and regeneration in relation to synthetic fibres, thus justifying its utilization. In the present research work, composites were developed with chicken feathers (KF), using unsaturated polyester resin as matrix, for diversified applications, mainly in the furniture/timber industry.At present, in Brazil the chicken feathers are used as part of the animal feed, even though this material possesses low aggregated value. The chicken feathers are hollow, light and resistant. After washing with water at room temperature, a part of the chicken feathers were treated with 2% NaOH. Composites were manufactured using treated and untreated chicken feathers with unsaturated orthothalic polyester resin and 1% peroxide as catalyser, obtained in the commerce. Samples with size 150x25x3 mm for mechanical tests were cut by laser in the composite plate. Mechanical analyses were carried out in the Laboratório de Metais e Ensaios Mecânicos UFRN. All the analyses were in accordance with ASTM standards. SEM analyses were also carried out on the samples.In the analyses of the results obtained, it was observed that the composites made with untreated chicken feathers showed better results (Traction 11.406 MPa and 9.107 MPa Bending 34.947 and 20.918 MPa for samples with and without treatment respectively) compared to the composite with treated feathers. Very low values of the water absorption results, evidenced the impermeability characteristic of the feathers. From the SEM images, the structure, fracture and the fibre/matrix adsorption can be evidenced. In the flammability test, it was observed that despite the feathers having sulfur as a constituent, natural inhibitor of flame, no burning support of the composites, because the manufacturing process of the composite

Determinação de dados de equilíbrio líquido-vapor a altas pressões para sistemas de hidrocarbonetos assimétricos

Crude oil is a complex liquid mixture of organic and inorganic compounds that are dominated by hydrocarbons. It is a mixture of alkanes from the simplest to more complex aromatic compounds that are present derivatives such as gasoline, diesel, alcohol, kerosene, naphtha, etc.. These derivatives are extracted from any oil, however, only with a very high quality, in other words, when the content of hydrocarbons of low molecular weight is high means that production of these compounds is feasible. The American Petroleum Institute (API) developed a classification system for the various types of oil. In Brazil, the quality of most of the oil taken from wells is very low, so it is necessary to generate new technology to develop best practices for refining in order to produce petroleum products of higher commercial value. Therefore, it is necessary to study the thermodynamic equilibrium properties of its derivative compounds of interest. This dissertation aims to determine vapor-liquid equilibrium (VLE) data for the systems Phenilcyclohexane - CO2, and Cyclohexane - Phenilcyclohexane - CO2 at high pressure and temperatures between 30 to 70oC. Furthermore, comparisons between measured VLE experimental data from this work and from the literature in relation to the Peng- Robinson molecular thermodynamic model, using a simulation program SPECS IVCSEP v5.60 and two adjustable interaction parameters, have been performed for modeling and simulation purposes. Finally, the developed apparatus for determination of phase equilibrium data at high pressures is presented

Enhanced stabilization of aerosol-OT surfactant monolayer upon interaction with small amounts of bovine serum albumin at the air-water interface

An investigation is made of the influence from small amounts of the protein bovine serum albumin (BSA) on the lateral organization of low molecular weight surfactant sodium bis-2-ethylhexyl sulfosuccinate (AOT) at the air-water interface. Surface pressure (pi - A), surface potential (DeltaV - A) and Brewster angle microscopy (BAM) experiments were carried out, with particular emphasis on the monolayer stability under successive compression-expansion cycles. AOT monolayer is not stable at the air-water interface, which means that the majority of AOT molecules go into the aqueous subphase as monomers and/or normal micelles. When a waiting time elapses between spreading and compression, the surfactant monolayer tends to reorganize partially at the air-water interface, with a monolayer expansion being observed for waiting times as large as 12 h. The incorporation of very small amount of BSA (10(-9) M) at the interface, also inferred from BAM, increases the monolayer stability as revealed by pi - A and DeltaV - A results. For a waiting time of circa 3 h, the mixed monolayer reaches its maximum stability. This must be related to protein (and/or protein-surfactant complexes) adsorbed onto the AOT monolayer, thus altering the BSA conformation to accommodate its hydrophobic/hydrophilic residues. Furthermore, the effects from such small amounts of BSA in the monolayer formation and stabilization mean that the AOT monolayer responds cooperatively to BSA. (C) 2004 Elsevier B.V. All rights reserved.

Hydroxymethylnitrofurazone Is Active in a Murine Model of Chagas' Disease

The addition of a hydroxymethyl group to the antimicrobial drug nitrofurazone generated hydroxymethylnitrofurazone (NFOH), which had reduced toxicity when its activity against Trypanosoma cruzi was tested in a murine model of Chagas' disease. Four groups of 12 Swiss female mice each received 150 mg of body weight/kg/day of NFOH, 150 mg/kg/day of nitrofurazone (parental compound), 60 mg/kg/day of benznidazole (BZL), or the solvent as a placebo. Treatments were administered orally once a day 6 days a week until the completion of 60 doses. NFOH was as effective as BZL in keeping direct parasitemia at undetectable levels, and PCR results were negative. No histopathological lesions were seen 180 days after completion of the treatments, a time when the levels of anti-T. cruzi antibodies were very low in mice treated with either NFOH or BZL. Nitrofurazone was highly toxic, which led to an overall rate of mortality of 75% and necessitated interruption of the treatment. In contrast, the group treated with its hydroxymethyl derivative, NFOH, displayed the lowest mortality (16%), followed by the BZL (33%) and placebo (66%) groups. The findings of histopathological studies were consistent with these results, with the placebo group showing the most severe parasite infiltrates in skeletal muscle and heart tissue and the NFOH group showing the lowest. The present evidence suggests that NFOH is a promising anti-T. cruzi agent.

Influência da densidade de estocagem sobre o crescimento, ciclo de muda e o comportamento em juvenis do camarão marinho Litopenaeus vannamei

One of the factors that may interfere with the cultivation of Litopenaeus vannamei is the population density. This study aimed to assess the effect of density on growth, mortality, physical integrity and behavior of shrimp. The study was divided into two stages. At first, the shrimp were placed in tanks at densities of 50, 75 and 100 shrimp m-2. The animals were monitored in relation to the degree of proventricular filling, the stage of the molt cycle and physical integrity three times a week and in relation to the weight and length once a week. Mortality, growth and proventricular filling were not influenced by the density; frequency of records in specific stages of the molt cycle varied according to the density. The lower proportion of broken appendages and higher frequency of necrotic lesions occurred in lower density. The second stage of the research, conducted in aquaria, was divided into two parts. The first described social or feeding behavioral categories: slow displacement by contact, slow displacement by approximation, abrupt displacement by contact, abrupt displacement by approximation, reactivity, cannibalism, occupying the tray, get feed in the tray and get feed outside the tray. In the second part, these and other behavioral categories, described in the literature, were recorded in densities of 50, 75 and 100 shrimp m-2. Mortality was more frequent in higher density. The frequency of most behaviors mentioned above was very low, not differing between densities or being too low to determine differences between them. The behavioral profile of animals in different densities was, in general, very similar, with no difference in exploration, digging and cleaning between the densities. Even so, inactivity, feeding, crawling, burrowing, swimming, and proximity between animals were influenced by the density. These results suggest that some behaviors suffer greater interference from population density. However, the density may not have a broader influence on the animals when other factors, such as physico-chemical parameters of water and feed offering, are adequate

Low levels of realized seed and pollen gene flow and strong spatial genetic structure in a small, isolated and fragmented population of the tropical tree Copaifera langsdorffii Desf

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

A function to predict the risk for death in the neonatal sepsis

This was a prospective study of 43 septic neonates at the NICU of the School of Medicine of Botucatu, São Paulo State University. Clinical and laboratory data of sepsis were analyzed based on outcome divided into two groups, survival and death. We calculated the discriminatory power of the relevant variables for the diagnosis of sepsis in each group, and using software for Discriminant Analysis, a function was proposed. There were 43 septic cases with 31 survivals and 12 deaths. The variables that had the highest discriminatory power were: n(o) of compromised systems, the SNAP, FiO2, and (A-a)O2. The study of these and others variables, such as birth weight, n(o) of risk factors, and pH using a Linear Discriminant Function(LDF) allowed us to identify the high-risk neonates for death with a low error rate (8.33%). The LDF was: F = 0.00043 (birth weight) + 0.30367 (n(o) of risk factors) - 0.1171 (n(o) of compromised systems) + 0.33223 (SNAP) + 2.27972 (pH) - 14.96511 (FiO2) + 0.01814 ((A-a)O2). If F > 22.77 there was high risk of death. This study suggests that the LDF at the onset of sepsis is useful for the early identification of the high-risk neonates that need special clinical and laboratory surveillance.