Expression profiles of fetal membrane nicotinamide adenine dinucleotide phosphate oxidases (NOX) 2 and 3 differentiates spontaneous preterm birth and pPROM pathophysiologies

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

The Role of Implant/Abutment System on Torque Maintenance of Retention Screws and Vertical Misfit of Implant-Supported Crowns Before and After Mechanical Cycling

Purpose: This study aimed to evaluate the role of the implant/abutment system on torque maintenance of titanium retention screws and the vertical misfit of screw-retained implant-supported crowns before and after mechanical cycling. Materials and Methods: Three groups were studied: morse taper implants with conical abutments (MTC group), external-hexagon implants with conical abutments (EHC group), and external-hexagon implants with UCLA abutments (EHU group). Metallic crowns casted in cobalt-chromium alloy were used (n = 10). Retention screws received insertion torque and, after 3 minutes, initial detorque was measured. Crowns were retightened and submitted to cyclic loading testing under oblique loading (30 degrees) of 130 +/- 10 N at 2 Hz of frequency, totaling 1 x 10(6) cycles. After cycling, final detorque was measured. Vertical misfit was measured using a stereomicroscope. Data were analyzed by analysis of variance, Tukey test, and Pearson correlation test (P < .05). Results: All detorque values were lower than the insertion torque both before and after mechanical cycling. No statistically significant difference was observed among groups before mechanical cycling. After mechanical cycling, a statistically significantly lower loss of detorque was verified in the MTC group in comparison to the EHC group. Significantly lower vertical misfit values were noted after mechanical cycling but there was no difference among groups. There was no significant correlation between detorque values and vertical misfit. Conclusions: All groups presented a significant decrease of torque before and after mechanical cycling. The morse taper connection promoted the highest torque maintenance. Mechanical cycling reduced the vertical misfit of all groups, although no significant correlation between vertical misfit and torque loss was found.

Vertical transmission of hepatitis C virus: A tale of multiple outcomes

Globally, hepatitis C virus (HCV) infection affects approximately 130 million people and 3 million new infections occur annually. HCV is also recognized as an important cause of chronic liver disease in children. The absence of proofreading properties of the HCV RNA polymerase leads to a highly error prone replication process, allowing HCV to escape host immune response. The adaptive nature of HCV evolution dictates the outcome of the disease in many ways. Here, we investigated the molecular evolution of HCV in three unrelated children who acquired chronic HCV infection as a result of mother-to-child transmission, two of whom were also coinfected with HIV-1. The persistence of discrete HCV variants and their population structure were assessed using median joining network and Bayesian approaches. While patterns of viral evolution clearly differed between subjects, immune system dysfunction related to HIV coinfection or persistent HCV seronegativity stand as potential mechanisms to explain the lack of molecular evolution observed in these three cases. In contrast, treatment of HCV infection with PegIFN, which did not lead to sustained virologic responses in all 3 cases, was not associated with commensurate variations in the complexity of the variant spectrum. Finally, the differences in the degree of divergence suggest that the mode of transmission of the virus was not the main factor driving viral evolution. (C) 2013 Elsevier B. V. All rights reserved.

Comprehensive Analysis of Gene Expression Profiles of the Beet Armyworm Spodoptera exigua Larvae Challenged with Bacillus thuringiensis Vip3Aa Toxin

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Dose and temporal effects on gene expression profiles of urothelial cells from rats exposed to diuron

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Changes in gene expression in PBMCs profiles of PPAR alpha target genes in obese and non-obese individuals during fasting

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Profiles of steroid hormones in canine X-Linked muscular dystrophy via stable isotope dilution LC-MS/MS

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Metabolite profiles of essential oils in citrus peels and their taxonomic implications

China is an important center of origin for the genus Citrus L. of the family Rutaceae and is rich in wild Citrus species. The taxonomy of Citrus has been a subject of controversy for more than a half century. We propose that the metabolite profiles of Chinese native Citrus species can be used for classification and understanding of the taxonomic relationships within the Citrus germplasm. In this study, triplicate gas chromatography-mass spectrometry (GC-MS) metabolite profiles of 20 Citrus species/varieties were acquired, including 10 native varieties originating in China. R-(+)-limonene, alpha-pinene, sabinene and alpha-terpinene were found to be major characteristic components of the essential oils analyzed in this study, and these compounds contributed greatly to the metabolic classification. The three basic species of the subgenus Eucitrus (Swingle&apos;s system), i.e., C. reticulata Blanco, C. medica L. and C. grandis Osb., were clearly differentiated based upon their metabolite profiles using hierarchical cluster analysis (HCA) and partial least square-discriminant analysis (PLS-DA). All the presumed hybrid genotypes, including sweet orange (C. sinensis Osb.), sour orange (C. aurantium L.), lemon (C. limon Burm.f.), rough lemon (C. jambhiri Lush.), rangpur lime (C. limonia Osb.) and grapefruit (C. paradisi Macf.), were grouped closely together with one of their suggested parent species in the HCA-dendrogram and the PLS-DA score plot. These results clearly demonstrated that the metabolite profiles of Citrus species could be utilized for the taxonomic classification of the genus and are complementary to the existing taxonomic evidence, especially for the identification and differentiation of hybrid species.

Characterization of the phenolic and antioxidant profiles of selected culinary herbs and spices: caraway, turmeric, dill, marjoram and nutmeg

Culinary herbs and spices have long been considered essentially as flavor enhancers or preservatives, with little attention given to their potential health-promoting properties. Nevertheless, recent research has shown them to be significant dietary sources of bioactive phenolic compounds. Despite noteworthy efforts performed in recent years to improve our knowledge of their chemical composition, a detailed phenolic profile of these plant-based products is still lacking. In the present work, antioxidant activities and phenolic composition of five herbs and spices, namely caraway, turmeric, dill, marjoram and nutmeg, have been studied. The use of liquid chromatography coupled to LTQ-Orbitrap mass spectrometry enabled the identification of up to 42 phenolic compounds. To the best of our knowledge, two of them, apigenin-C-hexoside-C-pentoside and apigenin-C-hexoside-C-hexoside have not been previously reported in turmeric. Qualitative and quantitative differences were observed in polyphenol profiles, with the highest phenolic content found in caraway. Multivariate statistical treatment of the results allowed the detection of distinctive features among the studied herbs and spices.

Clinical and epidemiological profiles of individuals with drug-resistant tuberculosis

Drug-resistant tuberculosis (TB) is a growing global threat. Approximately 450,000 people developed multidrugresistant TB worldwide in 2012 and an estimated 170,000 people died from the disease. This paper describes the sociodemographic, clinical-epidemiological and bacteriological aspects of TB and correlates these features with the distribution of anti-TB drug resistance. Mycobacterium tuberculosis (MT) cultures and drug susceptibility testing were performed according to the BACTEC MGIT 960 method. The results demonstrated that MT strains from individuals who received treatment for TB and people who were infected with human immunodeficiency virus were more resistant to TB drugs compared to other individuals (p &lt; 0.05). Approximately half of the individuals received supervised treatment, but most drug-resistant cases were positive for pulmonary TB and exhibited positive acid-fast bacilli smears, which are complicating factors for TB control programs. Primary healthcare is the ideal level for early disease detection, but tertiary healthcare is the most common entry point for patients into the system. These factors require special attention from healthcare managers and professionals to effectively control and monitor the spread of TB drug-resistant cases.

Effects of β-(1→3,1→6)-d-glucan and density of diets on the blood profiles of immunologically challenged weaned piglets

An experiment was conducted to evaluate the effects of two levels of the β-(1→3,1→6)-d-glucan (0 and 500ppm) from yeast Saccharomyces cerevisiae and two levels of energy (3300 and 3450kcalMEkg(-1)) on the hematological, immunological and, biochemical profiles of thirty-six 21-days-old weaned piglets, challenged with 150μgkg(-1) of BW lipopolysaccharide (LPS) from Escherichia coli serotype 055:B5. The experimental design was a randomized complete block design in a 2×2 factorial arrangement with nine replicates per treatment and, one animal per experimental unit. The data were analyzed in accordance with the multivariate analysis procedure of SAS and, the treatment means of parametric and non-parametric data were compared by Bonferroni's test (P<0.05) and, by Dunn's test (P<0.05), respectively. The data of the blood profiles of alanine aminotransferase, alkaline phosphatase and, creatinine showed that LPS did not cause kidney or liver damage in the animals. The addition of beta-glucan in the diets did not prove the robustness of its effect and biological relevance when provided with low nutrient-density. However, its addition combined with the high-nutrient-density diets showed less marked hypoglobulinemia in piglets, which may have contributed to the decreasing of the synthesis of inflammatory mediators.

Relationship between the morphology of the maxillary central incisor and horizontal and vertical measurements of the face

Purpose: In order to assist in the selection of artificial teeth for complete dentures, this study aimed to assess the relationship between horizontal and vertical measurements of the face and the morphology of the maxillary central incisor. Materials and Methods: This was a study of 50 plaster casts and 100 teleradiographs - 50 in lateral norm and 50 in frontal norm, belonging to 50 individuals, Caucasian, with a naturally optimal occlusion, matching at least four of the six keys of Andrews. Images of the upper central incisors were obtained by scanning the plaster casts (three-dimensional) and subjectively classified by three examiners as oval, triangular or quadrangular. Facial measures (vertical and horizontal) were defined by means of teleradiographs. In order to check inter-examiner agreement on the classification of central incisor, the Kappa test was used. To verify whether data had normal distribution, the Kolmogorov-Smirnov test was used ( P > 0.2) was used. One-way analysis of variance was employed to assess the association between variables (P > 0.05). Results: When vertical measurements were compared with the three incisor shapes, there was no statistically significant difference (P > 0.05): Triangular (0.54), oval (0.63) and quadrangular (0.51). Similarly, no difference (P > 0.05) was found for facial width (139.08, 143.37, 141.65), maxillary width (76.68, 78.99, 76.91) and mandibular width (103.47, 105.50, 103.11). Conclusions: The majority of cases showed that horizontal and vertical measurements of the face cannot be used as a reference for determining the morphology of the maxillary central incisor crown. It is relevant to analyze and compare other morphological structures to improve the oral health-related quality of life for the conventional denture wearer.

Impact of Solvent Quality on the Density Profiles of Looped Triblock Copolymer Brushes by Neutron Reflectivity Measurements

Preferential adsorption of poly(2-vinylpyridine)-deuterated polystyrene-poly(2-vinylpyridine) (PVP-dPS-PVP) triblock copolymers from toluene onto silicon leads to the formation of dPS loops tethered by the PVP end blocks. Using neutron reflectometry, we have determined the segment density profiles of these looped polymer brushes in toluene, a good solvent for the dPS block, and in cyclohexane at 20 °C (poor solvent), 32 °C, (near-Θ solvent), and 50 °C (marginal solvent). While the swelling behavior qualitatively agrees with that observed for singly grafted brushes, there are interesting differences in the local structural details: In a good solvent, the segment density profiles are composed of an inner parabolic region and a long, extended tail. In cyclohexane, the profiles are described by exponential decays. We ascribe these features to a novel polydispersity effect that arises due to tethering the PS loops by both ends. The results also show that the less dense layers undergo more significant changes in swollen height as solvent quality is changed and that the looped brushes of different molecular weight, asymmetry, and tethering density adhere to scaling relationships derived for lightly cross-linked polymer gels.

Vertical distribution of benthic invertebrate larvae during an upwelling event along a transect off the tropical Brazilian continental margin

Abundance and composition of marine benthic communities have been relatively well studied in the SE Brazilian coast, but little is known on patterns controlling the distribution of their planktonic larval stages. A survey of larval abundance in the continental margin, using a Multi-Plankton Sampler, was conducted in a cross-shelf transect off Cabo Frio (23 degrees S and 42 degrees W) during a costal upwelling event. Hydrographic conditions were monitored through discrete CDT casts. Chlorophyll-a in the top 100 m of the water column was determined and changes in surface chlorophyll-a was estimated using SeaWiFS images. Based on the larval abundances and the meso-scale hydrodynamics scenario, our results suggest two different processes affecting larval distributions. High larval densities were found nearshore due to the upwelling event associated with high chlorophyll a and strong along shore current. On the continental slope, high larval abundance was associated with a clockwise rotating meander, which may have entrapped larvae from a region located further north (Cabo de Sao Tome, 22 degrees S and 41 degrees W). In mid-shelf areas, our data suggests that vertical migration may likely occur as a response to avoid offshore transport by upwelling plumes and/or cyclonic meanders. The hydrodynamic scenario observed in the study area has two distinct yet extremely important consequences: larval retention on food-rich upwelling areas and the broadening of the tropical domain to southernmost subtropical areas. (C) 2009 Elsevier B.V. All rights reserved.

The rapid atmospheric monitoring system of the Pierre Auger Observatory

The Pierre Auger Observatory is a facility built to detect air showers produced by cosmic rays above 10(17) eV. During clear nights with a low illuminated moon fraction, the UV fluorescence light produced by air showers is recorded by optical telescopes at the Observatory. To correct the observations for variations in atmospheric conditions, atmospheric monitoring is performed at regular intervals ranging from several minutes (for cloud identification) to several hours (for aerosol conditions) to several days (for vertical profiles of temperature, pressure, and humidity). In 2009, the monitoring program was upgraded to allow for additional targeted measurements of atmospheric conditions shortly after the detection of air showers of special interest, e. g., showers produced by very high-energy cosmic rays or showers with atypical longitudinal profiles. The former events are of particular importance for the determination of the energy scale of the Observatory, and the latter are characteristic of unusual air shower physics or exotic primary particle types. The purpose of targeted (or "rapid") monitoring is to improve the resolution of the atmospheric measurements for such events. In this paper, we report on the implementation of the rapid monitoring program and its current status. The rapid monitoring data have been analyzed and applied to the reconstruction of air showers of high interest, and indicate that the air fluorescence measurements affected by clouds and aerosols are effectively corrected using measurements from the regular atmospheric monitoring program. We find that the rapid monitoring program has potential for supporting dedicated physics analyses beyond the standard event reconstruction.