Buried screen-printed contacts for silicon solar cells

A Simple way to improve solar cell efficiency is to enhance the absorption of light and reduce the shading losses. One of the main objectives for the photovoltaic roadmap is the reduction of metalized area on the front side of solar cell by fin lines. Industrial solar cell production uses screen-printing of metal pastes with a limit in line width of 70-80 μm. This paper will show a combination of the technique of laser grooved buried contact (LGBC) and Screen-printing is able to improve in fine lines and higher aspect ratio. Laser grooving is a technique to bury the contact into the surface of silicon wafer. Metallization is normally done with electroless or electrolytic plating method, which a high cost. To decrease the relative cost, more complex manufacturing process was needed, therefore in this project the standard process of buried contact solar cells has been optimized in order to gain a laser grooved buried contact solar cell concept with less processing steps. The laser scribing process is set at the first step on raw mono-crystalline silicon wafer. And then the texturing etch; phosphorus diffusion and SiNx passivation process was needed once. While simultaneously optimizing the laser scribing process did to get better results on screen-printing process with fewer difficulties to fill the laser groove. This project has been done to make the whole production of buried contact solar cell with fewer steps and could present a cost effective opportunity to solar cell industries.

Desenvolvimento de antenas de microfita e antenas DRA Broadband

The search for ever smaller device and without loss of performance has been increasingly investigated by researchers involving applied electromagnetics. Antennas using ceramics materials with a high dielectric constant, whether acting as a substract element of patch radiating or as the radiant element are in evidence in current research, that due to the numerous advantages offered, such as: low profile, ability to reduce the its dimensions when compared to other devices, high efficiency of ratiation, suitability the microwave range and/or millimeter wave, low temperature coefficient and low cost. The reason for this high efficiency is that the dielectric losses of ceramics are very low when compared to commercially materials sold used in printed circuit boards, such as fiberglass and phenolite. These characteristics make ceramic devices suitable for operation in the microwave band. Combining the design of patch antennas and/or dielectric resonator antenna (DRA) to certain materials and the method of synthesis of these powders in the manufacture of devices, it s possible choose a material with a dielectric constant appropriate for the design of an antenna with the desired size. The main aim of this work is the design of patch antennas and DRA antennas on synthesis of ceramic powders (synthesis by combustion and polymeric precursors - Pe- chini method) nanostructured with applications in the microwave band. The conventional method of mix oxides was also used to obtain nanometric powders for the preparation of tablets and dielectric resonators. The devices manufactured and studied on high dielectric constant materials make them good candidates to have their small size compared to other devices operating at the same frequency band. The structures analyzed are excited by three different techniques: i) microstrip line, ii) aperture coupling and iii) inductive coupling. The efficiency of these techniques have been investigated experimentally and compared with simulations by Ansoft HFSS, used in the accurate analysis of the electromagnetic behavior of antennas over the finite element method (FEM). In this thesis a literature study on the theory of microstrip antennas and DRA antenna is performed. The same study is performed about the materials and methods of synthesis of ceramic powders, which are used in the manufacture of tablets and dielectric cylinders that make up the devices investigated. The dielectric media which were used to support the analysis of the DRA and/or patch antennas are analyzed using accurate simulations using the finite difference time domain (FDTD) based on the relative electrical permittivity (er) and loss tangent of these means (tand). This work also presents a study on artificial neural networks, showing the network architecture used and their characteristics, as well as the training algorithms that were used in training and modeling some parameters associated with the devices investigated

Otimização dos parâmetros de monopolos planares de microfita para aplicações em sistemas de banda ultra larga

This work presents a theoretical and experimental investigation about the properties of microstrip antennas for ultra-wideband systems. Configurations of elliptic monopoles with different eccentricities and circular monopoles are considered. Two prototypes for each antenna configuration were built, one with the typical microstrip configuration and the other is similar to the first, except for a small aperture in the ground plane. Therefore, this work proposes to modify the configuration of the ground plane of the monopoles designed adding a rectangular stub, in order to optimize and improve the performance of such structures. The obtained results show that the introduction of that rectangular aperture in the ground plane allows an improvement of the frequency response for the considered antenna propotypes. It is observed a good agreement between the measured and simulated results. Finally, some proposals for future works are presented

Uma nova proposta de antenas Quasi-Yagi banda larga para comunicação sem fio

ln this work, planar quasi- Y agi antennas are investigated based on the concept of the classic Y agi_Uda antennas. These antennas represent improvements on the topologies of the antennas existing printed because they present characteristics of broad bandwidth, excellent radiation diagrams and simple construction. New configurations are adapted for the driver of the antennas, introducing patches elements into the driver. These new configurations are named Patches Elements Anteonas (PEA). This adaptation is obtained from simulations that are executed usiog the software C8T Microwave 8tudio 5. After doing the optimizations, procedures for construction and measurement ofthe prototypes are executed in order to improve the performance of the antennas in such way that they could be used in wireless communication applications, such as Bluetooth, WLAN' s and Wi-Fi. Next, the quasi- Y agi antennas are studied in order to implement them in arrangements. The arrangements construction is based 00 the best driver configuration of the antenna developed in this work. First, a linear arrangement composed by two elements of quasi¬Yagi antennas is constructed in such way that the radiation characteristics and the mutual coupling effects could be analyzed. After that, a 90° angle arrangement composed by two elements is studied to observe the effect of circular polarization. Experiments are executed in order to evaluate the arrangements performance. The experimental results show that the analysis made in this work is efficient and accurate. The numerical values obtained for the analyzed parameters of each structure developed are compared with the experimental values. 80, it is possible to observe a good concordance between them. Finally, some future works proposals are presented

Análise de antenas de microfita em rampa com múltiplas camadas dielétricas

The present work deals with the ana1ysis of microstrip patch antennas printed on tapered dielectric substrates. We investigate the influence ofthe substrate height variations on the properties of configurations such as microstrip patch antennas, microstrip patch antennas with overlay and suspendeô microstrip patch antennas. The dielectric substrates can be isotropic or anisotropic ones. This accurate analysis is based on the full-wave formulation. It is carried out initially for the determination of the impedance matrix, through the use of the spectral¬domain immitance approach. We use a model based on a segmentation of the considered line into uniform microstrip line subsections. Normalized phase constants and characteristic impedances are obtained by means of the Galerkin numerical technique. Then, the cascaded combination of the uniform microstrip subsections are analyzed through an interactive procedure. Numerical results are presented for the input reflection coefficient, voltage standing wave ratio, resonant frequency, and radiation pattems ofthe E_plane and H-plane diagrams. It is found that the variations in the substrate height profile produce a great influence on the bandwidth of microstrip antennas. This procedure gives bandwidth improvements without altering considerably the resonant frequency. Furthermore, the tapered microstrip antenna can be used as a lightweight altemative for bandwidth control and to eXtend the use of microstiip antenna technology to a wider variety of applications. Finally, suggestions for the continuity of this work are presented

Antenas monopolo planar com patch em anel circular para sistemas UWB

The microstrip antennas are largely used in wireless communication systems due to their low cost, weight, less complex construction and manufacturing, in addition to its versatility. UWB systems have emerged as an alternative to wireless communications over short distances because they offer of higher capacity and lower multipath distortion than other systems with the same purpose. Combining the advantages of microstrip antennas to the characteristics of UWB, it is possible to develop more and more smaller devices, with diverse geometries to operate satisfactorily in these systems. This paper aims to propose alternatives to microstrip antennas for UWB systems operate in the range between 3.1 and 10.6 GHz, with a patch on circular ring. Some techniques are analyzed and employed to increase the bandwidth of proposed antenna: the insertion of a parasitic elements and a rectangular slit in the displaced ground plane. For this, key issues are presented as the basic principles of UWB systems, the fundamental theory of antennas and microstrip antennas. The simulations and experimental characterization of constructed antennas are presented, as well as analysis of parameters such as bandwidth and radiation pattern

Caracterização numérica de antenas para aplicações RFID utilizando o método das ondas - WCIP

In recent years, the radio frequency identification technology (RFID) has gained great interest both industrial communities as scientific communities. Its ability to locate and monitor objects, animals and persons with active or passive tags allows easy development, with good cost-benefice and still presents undeniable benefits in applications ranging from logistics to healthcare, robotics, security, among others. Within this aspect what else comes excelling are RFID tags and the antennas used in RFID readers. Most tags have antennas omnidirectional and are usually manufactured as dipoles modified printed. The primary purpose of a project of antenna for tag is to achieve the required input impedance to perform a good marriage impedance with the load impedance of the chip. Already the objective principal in project of antennas for readers is to achieve reduced sizes and structures with good data transmission capacity. This work brings the numerical characterization of antennas for RFID applications, being these divided into tags RFID and antennas for RFID readers. Three tags RFID and two antennas for RFID readers, found in literature, are analyzed. The analysis of these structures is made using the Method of Waves - WCIP. Initial results found in the literature are compared with those obtained through simulations in WCIP with objective to show that the Method of Waves is able to analyze such structures. To illustrate the results obtained in simulations is presented the behavior of electric and magnetic fields. It also performed a literature review on the characteristics and principles of RFID technology. Suggestions for continuity to this work are presented

Antenas de microfita com patch em anel e múltiplas camadas dielétricas anisotrópicas uniaxiais

This work presents an analysis of the annular ring microstrip antennas printed on uniaxial anisotropic substrates and with superstrate.The analysis uses the full-wave formulation by means of the Hertz vector potentials method, in the Hankel transform domain. The definition of the Hertz vector potentials and the application of the appropriate boundary conditions to the structure allow determining the dyadic Green functions, relating the current densities in the conducting patch to the transforms of the tangential electric field components. Galerkin s method is then used to obtain the matrix equation whose nontrivial solution gives the complex resonant frequency of the antenna. From the modeling, it is possible to obtain results for the resonant frequency, bandwidth and quality factor, as a function of several parameters of the antenna, for different configurations. We have considered annular ring microstrip antennas on a single dielectric layer, antennas with two anisotropic dielectric layers, and annular ring microstrip antennas on suspended substrates. Numerical results for the resonant frequency of the these structures printed on isotropic substrates are also presented and compared with those published by other authors, showing a good agreement

Giant monopole resonance and nuclear compression modulus for Ca-40 and O-16

Using a collective potential derived previously on the basis of the generator coordinate method with Skyrme interactions, we obtain values for the compression modulus of Ca-40 which are in good agreement with a recently obtained experimental value. Calculated values for the compression modulus for O-16 are also given. The procedure involved in the derivation of the collective potential is briefly reviewed and discussed.

Electrochemical and spectroscopic characterization of screen-printed gold-based electrodes modified with self-assembled monolayers and Tc85 protein

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

DETECTION of BISPHENOL A on A SCREEN-PRINTED CARBON ELECTRODE IN CTAB MICELLAR MEDIUM

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Voltammetric sensing of the fuel dye marker Solvent Blue 14 by screen-printed electrodes

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Determination of isoniazid in human urine using screen-printed carbon electrode modified with poly-L-histidine

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)