Mechanochemical synthesis of CaTiO3 from CaCO3 - TiO2 mixture

The synthesis of calcium titanate, CaTiO3, was performed by mechanical activation and thermal treatment. Milling for up to 360 minutes in a planetary ball mill mechanically activated an equimolar mixture of CaCO 3 and TiO2 powders. A small amount of mechanically activated mixtures was pressed into briquettes and calcined at 850°C for two hours. The effect of mechanical activation on the solid-state reaction was studied using X-ray powder diffraction and differential thermal analysis. The change of morphology and size of powder particles due to milling, were determined by SEM, while BET analysis was used to determine the specific surface area of the powder. The sintering process was followed by a dilatometer during thermal treatment up to 1300°C. The main conclusion of the analysis of conducted investigations is that CaTiO3 ceramics can be obtained from an activated mixture at a much lower temperature than reported in the literature owing to acceleration of the chemical reaction and sintering.

Thermal degradation of both latex and latex cast films forming membranes: combined TG/FTIR investigation

Latex collected from natural rubber trees forming membranes can be used as biomaterials in several fields being the temperature a key parameter. Thermogravimetry (TG) coupled to Fourier transform infrared spectroscopy (FTIR) is a useful technique to investigate the thermal degradation of both latex and cast films (membranes), wich were obtained from Hevea brasiliensis (RRIM 600 clone) and used without stabilization. The membranes were prepared by casting the latex onto a glass substrate at 65 degrees C for 6 h. The thermal degradation was followed by FTIR spectra acquisition along the process, allowing the identification of the gaseous components evolved upon the thermal treatment. According to TG measurements, the main processes of thermal degradation of the latex and membranes occur at three temperature intervals for both.

Influence of Cu and Cr on the matrix decomposition of quenched Al-Zn-Mg alloy

The Inoue procedure is used to study the influence of Cr and Cu elements, jointly or individually, on the matrix decomposition of quenched Al-Zn-Mg alloys. The addition of copper and copper with chromium does not significantly change the limits of the temperatures of formation of Guinier-Preston zone and the range of the matrix decomposition. The control of the vacancy concentration in the alloys by different heat treatments and the addition of certain elements such as copper and chromium seems to play an important role in the nucleation rate and the kinetics of phase transformations.

Potentiodynamic behaviour of CuA1Ag alloys in NaOH: a comparative study related to the pure metals electrochemistry

The mechanism of electrochemical oxidation of surface reformed CuA1Ag alloys having different composition of heat treatment, in 0.5 M NaOH was studied by means of cyclic polarization, constant potential electrolysis, ICP, AA, SEM and EDX. The surface reformation consisted of a repetitive triangular potential sweep (RTPS) between H 2 and O 2 evolution at 100 mV s -1 in the working solution itself, performed in order to increase the electrode roughness and obtain a quasi-stationary I/E profile in which the potentiodynamic behaviour of copper and silver was clearly revealed. The alloys suffer aluminum dealloying after such an RTPS. The quasi-stationary cyclic polarization curve exhibits a multiplicity of current peaks which have been related to the electrochemical reactions involving the pure alloying elements. Complex potential perturbation programmes in regions having different anodic and cathodic limits allowed the study of the mechanism of the electrochemical oxidation of the surface reformed alloys and the compare with that corresponding to the pure metals. The basic differences between the electro-oxidation processes of the surface reformed CuA1Ag alloys with respect to those established for the high purity alloying metals are the splitting of the peaks corresponding to the formation of the Cu(I) and Ag(I) species. © 1991.

Estudo da estabilidade da cirurgia do tipo sagital da mandíbula com vista a correção de deformidades faciais

This research evaluated the surgical stabilily in patients with mandibular prognathism and retrognathism in which was used sagital split technic to correct those detormities. Twelve patients were selected from the clinic of only one experienced surgeon. Six patients presenter a Class III 6 a Class II molar relationship. A comparative cefalometric analysis using linear and angular measurements was performed of pre-surgery, imediate pós-surgery and 1 year follow-up. The following conclusions were obtained. 1 The Dal Pont sagital split technic modified by Epker to correct mandibular prognathisn and retroghnatism is a stable technic and must be indicated to correct those deformities. 2 Small relapses are easily corrected by the post-surgical orthodontic treatment. 3 A small over correction is advised in cases of large mandibular advancements or set bascks. 4 In those cases which a large amount of mandibular retrusion on advancement need to be performed, a combination of maxillary and mandibular surgery should be used. Rigid fixation technic is also indicated in those cases

Perfil microbilógico de diferentes tipos de saladas provenientes de cozinhas hospitalares

Pós-graduação em Medicina Veterinária - FMVZ

Avaliação dos aspectos de processo no torneamento de madeiras tratadas termicamente

Pós-graduação em Engenharia Mecânica - FEG

Otimização dos parâmetros para obtenção de nanotubos em Ti-Cp por anodização eletroquímica e aplicação na liga experimental Ti-35Nb-7Zr

Pós-graduação em Engenharia Mecânica - FEG

Caracterização mecânica e microestrutural de juntas soldadas a laser em aços maraging com posterior tratamento térmico e termoquímico de superfície a plasma

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Nível de satisfação dos pacientes edêntulos reabilitados com prótese total na faculdade de odontologia de Adamantina FAI

The population’s life expectancy is growing every year. This fact highlights the importance of the elderly for the dentistry. The oral cavity quality has great influence on quality of life at both the biological and the psychological and social factors by maintaining a self-esteem, self-expression, communication and satisfactory facial aesthetics. Unfortunately, the number of edentulous elderly population is also high, which may create problems to their social life. Therefore, the objective of this study was to demonstrate and evaluate the difficulties of treating edentulous patients, comparing data prior to treatment to post data after treatment by complete dentures made to the patients undergoing oral rehabilitation in the Dental Clinic of the Faculty of Dentistry of Adamantina – FAI. For this study, questionnaires were filled in the form of answers developed alternative focused on the degree of patient satisfaction, the current situation of occlusion, and outcome of treatment. The results showed that 96% of patients were satisfied with the results obtained in the treatment, all of whom believed that the prosthesis helped them feel better aesthetically and improved self-esteem. By this methodology, it was concluded that the degree of satisfaction was high, but the services provided must be constantly reevaluated, once the elderly population presents a wide labor market for dental professionals and demand level services will certainly increase each year.

Effectveness inactivation of trypsin inhibitor from brazilian cultivars of beans (Phaseolus vulgaris L.)

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Produção de uva passa de BRS Morena: pré-tratamento, caracterização físico-química e composição fenólica

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Cr+3 distribution in Al1 and Al2 Sites of alexandrite (BeAl2O4: Cr3+) induced by annealing, investigated by optical spectroscopy

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Synthesis and characterization of nanostructured TiO2-SnO2 composite

Nanostructured composites based on titanium dioxide have been studied in order to improve optical and photo-catalytic properties, as well as their performance in gas sensors. In this work, titanium and tin dioxides were simultaneously synthesized by the polyol method resulting in TiO2 platelet coated with SnO2 nanoparticles as was observed by scanning electron microscopy. The thermal analysis showed that the combined synthesis promotes more easily the crystallization of the TiO2 rutile phase. The composite obtained after heat treatment at 500 °C showed to be formed of almost only rutile phases of both oxides. The optical properties analyzed by UV-Vis spectroscopy showed that the combined oxides have higher absorbance, which reinforces a model found in the literature based on the flow of photo-generated electrons to the conduction band of SnO2 delaying the recombination of charges.

Síntese e caracterização de alvo de óxido de zinco dopado com alumínio

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)