Comparative tracing experiments to investigate epikarst structural and compositional heterogeneity

Comparative tracer testing may be used to evaluate the vulnerability of groundwater to specific contaminants by comparing reactive tracer response to that of a simultaneously injected non-reactive “conservative” substance. Conversely, knowledge of tracer reaction with specific materials permits information about subsurface heterogeneity to be inferred. A series of tests completed in the vadose zone overlying a limestone aquifer employed a cocktail of particles along with reactive and non-reactive solute tracers to investigate transport rates between the ground surface and monitoring points approximately 10 m below ground. Short pulse tests revealed both solutes and particulate contaminants could travel at rates of over 10 m/h. Comparison of particle (microorganisms) and non-reactive solute tracer breakthrough revealed that particle tracers experience pore exclusion resulting in higher peak relative concentrations which arrive earlier than those of the solute. Prolonged tracer injection during subsequent experiments confirmed the response observed and illustrated that over 40 % of flow paths between injection and monitoring points were inaccessible to particles, but could allow solutes to pass through them. Similarly, the difference in response between various reactive tracers demonstrated tracers reached monitoring points via multiple flow paths and suggests geochemical heterogeneity plays an important role in influencing tracer behaviour. The results of this investigation highlight the complexity of water flow through the epikarst and the vulnerability of groundwater in karst aquifers to contamination when soil cover is thin to absent.

A review of Ni-like X-ray laser experiments undertaken using the VULCAN laser at the Rutherford Appleton Laboratory

Recent progress using the VULCAN laser at the Rutherford Appleton Laboratory to pump X-ray lasing in nickel-like ions is reviewed. Double pulse pumping with similar to 100 ps pulses has been shown to produce significantly greater X-ray laser output than single pulses of duration 0.1-1 ns. With double pulse pumping, the main pumping pulse interacts with a pre-formed plasma created by a pre-pulse. The efficiency of lasing increases as there is a reduced effect of refraction of the X-ray laser beam due to smaller density gradients and larger gain volumes, which enable propagation of the X-ray laser beam along the full length of the target. The record shortest wavelength saturated laser at 5.9 nm has been achieved in Ni-like dysprosium using double pulse pumping of 75 ps duration from the VULCAN laser. A variant of the double pulse pumping using a single similar to 100 ps laser pulse and a superimposed short similar to 1 ps pulse has been found to further increase the efficiency of lasing by reducing the effects of over-ionisation during the gain period. The record shortest wavelength saturated laser pumped by a short similar to 1 ps pulse has been achieved in Ni-like samarium using the VULCAN laser operating in chirped pulse amplified (CPA) mode. Ni-like samarium lases at 7.3 nm. (C) 2000 Academie des sciences/Editions scientifiques et medicales Elsevier SAS.

A virtual inspection framework for precision manufacturing of aerofoil components

The finite element method plays an extremely important role in forging process design as it provides a valid means to quantify forging errors and thereby govern die shape modification to improve the dimensional accuracy of the component. However, this dependency on process simulation could raise significant problems and present a major drawback if the finite element simulation results were inaccurate. This paper presents a novel approach to assess the dimensional accuracy and shape quality of aeroengine blades formed from finite element hot-forging simulation. The proposed virtual inspection system uses conventional algorithms adopted by modern coordinate measurement processes as well as the latest free-form surface evaluation techniques to provide a robust framework for virtual forging error assessment. Established techniques for the physical registration of real components have been adapted to localise virtual models in relation to a nominal Design Coordinate System. Blades are then automatically analysed using a series of intelligent routines to generate measurement data and compute dimensional errors. The results of a comparison study indicate that the virtual inspection results and actual coordinate measurement data are highly comparable, validating the approach as an effective and accurate means to quantify forging error in a virtual environment. Consequently, this provides adequate justification for the implementation of the virtual inspection system in the virtual process design, modelling and validation of forged aeroengine blades in industry.