Comportamiento mecánico de nuevas aleaciones de wolframio en función de la temperatura

La presente memoria de tesis tiene como objetivo principal la caracterización mecánica en función de la temperatura de nueve aleaciones de wolframio con contenidos diferentes en titanio, vanadio, itria y lantana. Las aleaciones estudiadas son las siguientes: W-0.5%Y2O3, W-2%Ti, W-2% Ti-0.5% Y2O3, W-4% Ti-0.5% Y2O3, W-2%V, W- 2%Vmix, W-4%V, W-1%La2O3 and W-4%V-1%La2O3. Todos ellos, además del wolframio puro se fabrican mediante compresión isostática en caliente (HIP) y son suministradas por la Universidad Carlos III de Madrid. La investigación se desarrolla a través de un estudio sistemático basado en ensayos físicos y mecánicos, así como el análisis post mortem de las muestras ensayadas. Para realizar dicha caracterización mecánica se aplican diferentes ensayos mecánicos, la mayoría de ellos realizados en el intervalo de temperatura de 25 a 1000 º C. Los ensayos de caracterización que se llevan a cabo son: • Densidad • Dureza Vicker • Módulo de elasticidad y su evolución con la temperatura • Límite elástico o resistencia a la flexión máxima, y su evolución con la temperatura • Resistencia a la fractura y su comportamiento con la temperatura. • Análisis microestructural • Análisis fractográfico • Análisis de la relación microestructura-comportamiento macroscópico. El estudio comienza con una introducción acerca de los sistemas en los que estos materiales son candidatos para su aplicación, para comprender las condiciones a las que los materiales serán expuestos. En este caso, el componente que determina las condiciones es el Divertor del reactor de energía de fusión por confinamiento magnético. Parece obvio que su uso en los componentes del reactor de fusión, más exactamente como materiales de cara al plasma (Plasma Facing Components o PFC), hace que estas aleaciones trabajen bajo condiciones de irradiación de neutrones. Además, el hecho de que sean materiales nuevos hace necesario un estudio previo de las características básicas que garantice los requisitos mínimos antes de realizar un estudio más complejo. Esto constituye la principal motivación de la presente investigación. La actual crisis energética ha llevado a aunar esfuerzos en el desarrollo de nuevos materiales, técnicas y dispositivos para la aplicación en la industria de la energía nuclear. El desarrollo de las técnicas de producción de aleaciones de wolframio, con un punto de fusión muy alto, requiere el uso de precursores de sinterizado para lograr densificaciones más altas y por lo tanto mejores propiedades mecánicas. Este es el propósito de la adición de titanio y vanadio en estas aleaciones. Sin embargo, uno de los principales problemas de la utilización de wolframio como material estructural es su alta temperatura de transición dúctil-frágil. Esta temperatura es característica de materiales metálicos con estructura cúbica centrada en el cuerpo y depende de varios factores metalúrgicos. El proceso de recristalización aumenta esta temperatura de transición. Los PFC tienen temperaturas muy altas de servicio, lo que facilita la recristalización del metal. Con el fin de retrasar este proceso, se dispersan partículas insolubles en el material permitiendo temperaturas de servicio más altas. Hasta ahora se ha utilizado óxidos de torio, lantano e itrio como partículas dispersas. Para entender cómo los contenidos en algunos elementos y partículas de óxido afectan a las propiedades de wolframio se estudian las aleaciones binarias de wolframio en comparación con el wolframio puro. A su vez estas aleaciones binarias se utilizan como material de referencia para entender el comportamiento de las aleaciones ternarias. Dada la estrecha relación entre las propiedades del material, la estructura y proceso de fabricación, el estudio se completa con un análisis fractográfico y micrográfico. El análisis fractográfico puede mostrar los mecanismos que están implicados en el proceso de fractura del material. Por otro lado, el estudio micrográfico ayudará a entender este comportamiento a través de la identificación de las posibles fases presentes. La medida del tamaño de grano es una parte de la caracterización microestructural. En esta investigación, la medida del tamaño de grano se llevó a cabo por ataque químico selectivo para revelar el límite de grano en las muestras preparadas. Posteriormente las micrografías fueron sometidas a tratamiento y análisis de imágenes. El documento termina con una discusión de los resultados y la compilación de las conclusiones más importantes que se alcanzan después del estudio. Actualmente, el desarrollo de nuevos materiales para aplicación en los componentes de cara al plasma continúa. El estudio de estos materiales ayudará a completar una base de datos de características que permita hacer una selección de ellos más fiable. The main goal of this dissertation is the mechanical characterization as a function of temperature of nine tungsten alloys containing different amounts of titanium, vanadium and yttrium and lanthanum oxide. The alloys under study were the following ones: W-0.5%Y2O3, W-2%Ti, W-2% Ti-0.5% Y2O3, W-4% Ti-0.5% Y2O3, W-2%V, W- 2%Vmix, W-4%V, W-1%La2O3 and W-4%V-1%La2O3. All of them, besides pure tungsten, were manufactured using a Hot Isostatic Pressing (HIP) process and they were supplied by the Universidad Carlos III de Madrid. The research was carried out through a systematic study based on physical and mechanical tests as well as the post mortem analysis of tested samples. Diverse mechanical tests were applied to perform this characterization; most of them were conducted at temperatures in the range 25-1000 ºC. The following characterization tests were performed: • Density • Vickers hardness • Elastic modulus • Yield strength or ultimate bending strength, and their evolution with temperature • Fracture toughness and its temperature behavior • Microstructural analysis • Fractographical analysis • Microstructure-macroscopic relationship analysis This study begins with an introduction regarding the systems where these materials could be applied, in order to establish and understand their service conditions. In this case, the component that defines the conditions is the Divertor of magnetic-confinement fusion reactors. It seems obvious that their use as fusion reactor components, more exactly as plasma facing components (PFCs), makes these alloys work under conditions of neutron irradiation. In addition to this, the fact that they are novel materials demands a preliminary study of the basic characteristics which will guarantee their minimum requirements prior to a more complex study. This constitutes the motivation of the present research. The current energy crisis has driven to join forces so as to develop new materials, techniques and devices for their application in the nuclear energy industry. The development of production techniques for tungsten-based alloys, with a very high melting point, requires the use of precursors for sintering to achieve higher densifications and, accordingly, better mechanical properties. This is the purpose of the addition of titanium and vanadium to these alloys. Nevertheless, one of the main problems of using tungsten as structural material is its high ductile-brittle transition temperature. This temperature is characteristic of metallic materials with body centered cubic structure and depends on several metallurgical factors. The recrystallization process increases their transition temperature. Since PFCs have a very high service temperature, this facilitates the metal recrystallization. In order to inhibit this process, insoluble particles are dispersed in the material allowing higher service temperatures. So far, oxides of thorium, lanthanum and yttrium have been used as dispersed particles. Tungsten binary alloys are studied in comparison with pure tungsten to understand how the contents of some elements and oxide particles affect tungsten properties. In turn, these binary alloys are used as reference materials to understand the behavior of ternary alloys. Given the close relationship between the material properties, structure and manufacturing process, this research is completed with a fractographical and micrographic analysis. The fractographical analysis is aimed to show the mechanisms that are involved in the process of the material fracture. Besides, the micrographic study will help to understand this behavior through the identification of present phases. The grain size measurement is a crucial part of the microstructural characterization. In this work, the measurement of grain size was carried out by chemical selective etching to reveal the boundary grain on prepared samples. Afterwards, micrographs were subjected to both treatment and image analysis. The dissertation ends with a discussion of results and the compilation of the most important conclusions reached through this work. The development of new materials for plasma facing components application is still under study. The analysis of these materials will help to complete a database of the features that will allow a more reliable materials selection.

Quantitative analysis of morphological changes in yeast colonies growing on solid medium: the eccentricity and Fourier indices

The colony shape of four yeast species growing on agar medium wasmeasured for 116 days by image analysis. Initially, all the colonies are circular, with regular edges. The loss of circularity can be quantitatively estimated by the eccentricity index, Ei, calculated as the ratio between their orthogonal vertical and horizontal diameters. Ei can increase from 1 (complete circularity) to a maximum of 1.17–1.30, depending on the species. One colony inhibits its neighbour only when it has reached a threshold area. Then, Ei of the inhibited colony increases proportionally to the area of the inhibitory colony. The initial distance between colonies affects those threshold values but not the proportionality, Ei/area; this inhibition affects the shape but not the total surface of the colony. The appearance of irregularities in the edges is associated, in all the species, not with age but with nutrient exhaustion. The edge irregularity can be quantified by the Fourier index, Fi, calculated by the minimum number of Fourier coefficients that are needed to describe the colony contour with 99% fitness. An ad hoc function has been developed in Matlab v. 7.0 to automate the computation of the Fourier coefficients. In young colonies, Fi has a value between 2 (circumference) and 3 (ellipse). These values are maintained in mature colonies of Debaryomyces, but can reach values up to 14 in Saccharomyces.All the species studied showed the inhibition of growth in facing colony edges, but only three species showed edge irregularities associated with substrate exhaustion. Copyright © 2014 John Wiley & Sons, Ltd.

Age regression from soft aligned face images using low computational resources

The initial step in most facial age estimation systems consists of accurately aligning a model to the output of a face detector (e.g. an Active Appearance Model). This fitting process is very expensive in terms of computational resources and prone to get stuck in local minima. This makes it impractical for analysing faces in resource limited computing devices. In this paper we build a face age regressor that is able to work directly on faces cropped using a state-of-the-art face detector. Our procedure uses K nearest neighbours (K-NN) regression with a metric based on a properly tuned Fisher Linear Discriminant Analysis (LDA) projection matrix. On FG-NET we achieve a state-of-the-art Mean Absolute Error (MAE) of 5.72 years with manually aligned faces. Using face images cropped by a face detector we get a MAE of 6.87 years in the same database. Moreover, most of the algorithms presented in the literature have been evaluated on single database experiments and therefore, they report optimistically biased results. In our cross-database experiments we get a MAE of roughly 12 years, which would be the expected performance in a real world application.

Design and development of compact optical systems = Diseño y desarrollo de sistemas ópticos compactos

Esta tesis considera dos tipos de aplicaciones del diseño óptico: óptica formadora de imagen por un lado, y óptica anidólica (nonimaging) o no formadora de imagen, por otro. Las ópticas formadoras de imagen tienen como objetivo la obtención de imágenes de puntos del objeto en el plano de la imagen. Por su parte, la óptica anidólica, surgida del desarrollo de aplicaciones de concentración e iluminación, se centra en la transferencia de energía en forma de luz de forma eficiente. En general, son preferibles los diseños ópticos que den como resultado sistemas compactos, para ambos tipos de ópticas (formadora de imagen y anidólica). En el caso de los sistemas anidólicos, una óptica compacta permite tener costes de producción reducidos. Hay dos razones: (1) una óptica compacta presenta volúmenes reducidos, lo que significa que se necesita menos material para la producción en masa; (2) una óptica compacta es pequeña y ligera, lo que ahorra costes en el transporte. Para los sistemas ópticos de formación de imagen, además de las ventajas anteriores, una óptica compacta aumenta la portabilidad de los dispositivos, que es una gran ventaja en tecnologías de visualización portátiles, tales como cascos de realidad virtual (HMD del inglés Head Mounted Display). Esta tesis se centra por tanto en nuevos enfoques de diseño de sistemas ópticos compactos para aplicaciones tanto de formación de imagen, como anidólicas. Los colimadores son uno de los diseños clásicos dentro la óptica anidólica, y se pueden utilizar en aplicaciones fotovoltaicas y de iluminación. Hay varios enfoques a la hora de diseñar estos colimadores. Los diseños convencionales tienen una relación de aspecto mayor que 0.5. Con el fin de reducir la altura del colimador manteniendo el área de iluminación, esta tesis presenta un diseño de un colimador multicanal. En óptica formadora de imagen, las superficies asféricas y las superficies sin simetría de revolución (o freeform) son de gran utilidad de cara al control de las aberraciones de la imagen y para reducir el número y tamaño de los elementos ópticos. Debido al rápido desarrollo de sistemas de computación digital, los trazados de rayos se pueden realizar de forma rápida y sencilla para evaluar el rendimiento del sistema óptico analizado. Esto ha llevado a los diseños ópticos modernos a ser generados mediante el uso de diferentes técnicas de optimización multi-paramétricas. Estas técnicas requieren un buen diseño inicial como punto de partida para el diseño final, que será obtenido tras un proceso de optimización. Este proceso precisa un método de diseño directo para superficies asféricas y freeform que den como resultado un diseño cercano al óptimo. Un método de diseño basado en ecuaciones diferenciales se presenta en esta tesis para obtener un diseño óptico formado por una superficie freeform y dos superficies asféricas. Esta tesis consta de cinco capítulos. En Capítulo 1, se presentan los conceptos básicos de la óptica formadora de imagen y de la óptica anidólica, y se introducen las técnicas clásicas del diseño de las mismas. El Capítulo 2 describe el diseño de un colimador ultra-compacto. La relación de aspecto ultra-baja de este colimador se logra mediante el uso de una estructura multicanal. Se presentará su procedimiento de diseño, así como un prototipo fabricado y la caracterización del mismo. El Capítulo 3 describe los conceptos principales de la optimización de los sistemas ópticos: función de mérito y método de mínimos cuadrados amortiguados. La importancia de un buen punto de partida se demuestra mediante la presentación de un mismo ejemplo visto a través de diferentes enfoques de diseño. El método de las ecuaciones diferenciales se presenta como una herramienta ideal para obtener un buen punto de partida para la solución final. Además, diferentes técnicas de interpolación y representación de superficies asféricas y freeform se presentan para el procedimiento de optimización. El Capítulo 4 describe la aplicación del método de las ecuaciones diferenciales para un diseño de un sistema óptico de una sola superficie freeform. Algunos conceptos básicos de geometría diferencial son presentados para una mejor comprensión de la derivación de las ecuaciones diferenciales parciales. También se presenta un procedimiento de solución numérica. La condición inicial está elegida como un grado de libertad adicional para controlar la superficie donde se forma la imagen. Basado en este enfoque, un diseño anastigmático se puede obtener fácilmente y se utiliza como punto de partida para un ejemplo de diseño de un HMD con una única superficie reflectante. Después de la optimización, dicho diseño muestra mejor rendimiento. El Capítulo 5 describe el método de las ecuaciones diferenciales ampliado para diseños de dos superficies asféricas. Para diseños ópticos de una superficie, ni la superficie de imagen ni la correspondencia entre puntos del objeto y la imagen pueden ser prescritas. Con esta superficie adicional, la superficie de la imagen se puede prescribir. Esto conduce a un conjunto de tres ecuaciones diferenciales ordinarias implícitas. La solución numérica se puede obtener a través de cualquier software de cálculo numérico. Dicho procedimiento también se explica en este capítulo. Este método de diseño da como resultado una lente anastigmática, que se comparará con una lente aplanática. El diseño anastigmático converge mucho más rápido en la optimización y la solución final muestra un mejor rendimiento. ABSTRACT We will consider optical design from two points of view: imaging optics and nonimaging optics. Imaging optics focuses on the imaging of the points of the object. Nonimaging optics arose from the development of concentrators and illuminators, focuses on the transfer of light energy, and has wide applications in illumination and concentration photovoltaics. In general, compact optical systems are necessary for both imaging and nonimaging designs. For nonimaging optical systems, compact optics use to be important for reducing cost. The reasons are twofold: (1) compact optics is small in volume, which means less material is needed for mass-production; (2) compact optics is small in size and light in weight, which saves cost in transportation. For imaging optical systems, in addition to the above advantages, compact optics increases portability of devices as well, which contributes a lot to wearable display technologies such as Head Mounted Displays (HMD). This thesis presents novel design approaches of compact optical systems for both imaging and nonimaging applications. Collimator is a typical application of nonimaging optics in illumination, and can be used in concentration photovoltaics as well due to the reciprocity of light. There are several approaches for collimator designs. In general, all of these approaches have an aperture diameter to collimator height not greater than 2. In order to reduce the height of the collimator while maintaining the illumination area, a multichannel design is presented in this thesis. In imaging optics, aspheric and freeform surfaces are useful in controlling image aberrations and reducing the number and size of optical elements. Due to the rapid development of digital computing systems, ray tracing can be easily performed to evaluate the performance of optical system. This has led to the modern optical designs created by using different multi-parametric optimization techniques. These techniques require a good initial design to be a starting point so that the final design after optimization procedure can reach the optimum solution. This requires a direct design method for aspheric and freeform surface close to the optimum. A differential equation based design method is presented in this thesis to obtain single freeform and double aspheric surfaces. The thesis comprises of five chapters. In Chapter 1, basic concepts of imaging and nonimaging optics are presented and typical design techniques are introduced. Readers can obtain an understanding for the following chapters. Chapter 2 describes the design of ultra-compact collimator. The ultra-low aspect ratio of this collimator is achieved by using a multichannel structure. Its design procedure is presented together with a prototype and its evaluation. The ultra-compactness of the device has been approved. Chapter 3 describes the main concepts of optimizing optical systems: merit function and Damped Least-Squares method. The importance of a good starting point is demonstrated by presenting an example through different design approaches. The differential equation method is introduced as an ideal tool to obtain a good starting point for the final solution. Additionally, different interpolation and representation techniques for aspheric and freeform surface are presented for optimization procedure. Chapter 4 describes the application of differential equation method in the design of single freeform surface optical system. Basic concepts of differential geometry are presented for understanding the derivation of partial differential equations. A numerical solution procedure is also presented. The initial condition is chosen as an additional freedom to control the image surface. Based on this approach, anastigmatic designs can be readily obtained and is used as starting point for a single reflective surface HMD design example. After optimization, the evaluation shows better MTF. Chapter 5 describes the differential equation method extended to double aspheric surface designs. For single optical surface designs, neither image surface nor the mapping from object to image can be prescribed. With one more surface added, the image surface can be prescribed. This leads to a set of three implicit ordinary differential equations. Numerical solution can be obtained by MATLAB and its procedure is also explained. An anastigmatic lens is derived from this design method and compared with an aplanatic lens. The anastigmatic design converges much faster in optimization and the final solution shows better performance.

Global instability analysis and control of three-dimensional long open cavity flow

The three-dimensional wall-bounded open cavity may be considered as a simplified geometry found in industrial applications such as leading gear or slotted flats on the airplane. Understanding the three-dimensional complex flow structure that surrounds this particular geometry is therefore of major industrial interest. At the light of the remarkable former investigations in this kind of flows, enough evidences suggest that the lateral walls have a great influence on the flow features and hence on their instability modes. Nevertheless, even though there is a large body of literature on cavity flows, most of them are based on the assumption that the flow is two-dimensional and spanwise-periodic. The flow over realistic open cavity should be considered. This thesis presents an investigation of three-dimensional wall-bounded open cavity with geometric ratio 6:2:1. To this aim, three-dimensional Direct Numerical Simulation (DNS) and global linear instability have been performed. Linear instability analysis reveals that the onset of the first instability in this open cavity is around Recr 1080. The three-dimensional shear layer mode with a complex structure is shown to be the most unstable mode. I t is noteworthy that the flow pattern of this high-frequency shear layer mode is similar to the observed unstable oscillations in supercritical unstable case. DNS of the cavity flow carried out at different Reynolds number from steady state until a nonlinear saturated state is obtained. The comparison of time histories of kinetic energy presents a clearly dominant energetic mode which shifts between low-frequency and highfrequency oscillation. A complete flow patterns from subcritical cases to supercritical case has been put in evidence. The flow structure at the supercritical case Re=1100 resembles typical wake-shedding instability oscillations with a lateral motion existed in the subcritical cases. Also, This flow pattern is similar to the observations in experiments. In order to validate the linear instability analysis results, the topology of the composite flow fields reconstructed by linear superposition of a three-dimensional base flow and its leading three-dimensional global eigenmodes has been studied. The instantaneous wall streamlines of those composited flows display distinguish influence region of each eigenmode. Attention has been focused on the leading high-frequency shear layer mode; the composite flow fields have been fully recognized with respect to the downstream wave shedding. The three-dimensional shear layer mode is shown to give rise to a typical wake-shedding instability with a lateral motions occurring downstream which is in good agreement with the experiment results. Moreover, the spanwise-periodic, open cavity with the same length to depth ratio has been also studied. The most unstable linear mode is different from the real three-dimensional cavity flow, because of the existence of the side walls. Structure sensitivity of the unstable global mode is analyzed in the flow control context. The adjoint-based sensitivity analysis has been employed to localized the receptivity region, where the flow is more sensible to momentum forcing and mass injection. Because of the non-normality of the linearized Navier-Stokes equations, the direct and adjoint field has a large spatial separation. The strongest sensitivity region is locate in the upstream lip of the three-dimensional cavity. This numerical finding is in agreement with experimental observations. Finally, a prototype of passive flow control strategy is applied.

Estimación eficiente de atributos demográficos del rostro humano en imágenes

Sin duda, el rostro humano ofrece mucha más información de la que pensamos. La cara transmite sin nuestro consentimiento señales no verbales, a partir de las interacciones faciales, que dejan al descubierto nuestro estado afectivo, actividad cognitiva, personalidad y enfermedades. Estudios recientes [OFT14, TODMS15] demuestran que muchas de nuestras decisiones sociales e interpersonales derivan de un previo análisis facial de la cara que nos permite establecer si esa persona es confiable, trabajadora, inteligente, etc. Esta interpretación, propensa a errores, deriva de la capacidad innata de los seres humanas de encontrar estas señales e interpretarlas. Esta capacidad es motivo de estudio, con un especial interés en desarrollar métodos que tengan la habilidad de calcular de manera automática estas señales o atributos asociados a la cara. Así, el interés por la estimación de atributos faciales ha crecido rápidamente en los últimos años por las diversas aplicaciones en que estos métodos pueden ser utilizados: marketing dirigido, sistemas de seguridad, interacción hombre-máquina, etc. Sin embargo, éstos están lejos de ser perfectos y robustos en cualquier dominio de problemas. La principal dificultad encontrada es causada por la alta variabilidad intra-clase debida a los cambios en la condición de la imagen: cambios de iluminación, oclusiones, expresiones faciales, edad, género, etnia, etc.; encontradas frecuentemente en imágenes adquiridas en entornos no controlados. Este de trabajo de investigación estudia técnicas de análisis de imágenes para estimar atributos faciales como el género, la edad y la postura, empleando métodos lineales y explotando las dependencias estadísticas entre estos atributos. Adicionalmente, nuestra propuesta se centrará en la construcción de estimadores que tengan una fuerte relación entre rendimiento y coste computacional. Con respecto a éste último punto, estudiamos un conjunto de estrategias para la clasificación de género y las comparamos con una propuesta basada en un clasificador Bayesiano y una adecuada extracción de características. Analizamos en profundidad el motivo de porqué las técnicas lineales no han logrado resultados competitivos hasta la fecha y mostramos cómo obtener rendimientos similares a las mejores técnicas no-lineales. Se propone un segundo algoritmo para la estimación de edad, basado en un regresor K-NN y una adecuada selección de características tal como se propuso para la clasificación de género. A partir de los experimentos desarrollados, observamos que el rendimiento de los clasificadores se reduce significativamente si los ´estos han sido entrenados y probados sobre diferentes bases de datos. Hemos encontrado que una de las causas es la existencia de dependencias entre atributos faciales que no han sido consideradas en la construcción de los clasificadores. Nuestro resultados demuestran que la variabilidad intra-clase puede ser reducida cuando se consideran las dependencias estadísticas entre los atributos faciales de el género, la edad y la pose; mejorando el rendimiento de nuestros clasificadores de atributos faciales con un coste computacional pequeño. Abstract Surely the human face provides much more information than we think. The face provides without our consent nonverbal cues from facial interactions that reveal our emotional state, cognitive activity, personality and disease. Recent studies [OFT14, TODMS15] show that many of our social and interpersonal decisions derive from a previous facial analysis that allows us to establish whether that person is trustworthy, hardworking, intelligent, etc. This error-prone interpretation derives from the innate ability of human beings to find and interpret these signals. This capability is being studied, with a special interest in developing methods that have the ability to automatically calculate these signs or attributes associated with the face. Thus, the interest in the estimation of facial attributes has grown rapidly in recent years by the various applications in which these methods can be used: targeted marketing, security systems, human-computer interaction, etc. However, these are far from being perfect and robust in any domain of problems. The main difficulty encountered is caused by the high intra-class variability due to changes in the condition of the image: lighting changes, occlusions, facial expressions, age, gender, ethnicity, etc.; often found in images acquired in uncontrolled environments. This research work studies image analysis techniques to estimate facial attributes such as gender, age and pose, using linear methods, and exploiting the statistical dependencies between these attributes. In addition, our proposal will focus on the construction of classifiers that have a good balance between performance and computational cost. We studied a set of strategies for gender classification and we compare them with a proposal based on a Bayesian classifier and a suitable feature extraction based on Linear Discriminant Analysis. We study in depth why linear techniques have failed to provide competitive results to date and show how to obtain similar performances to the best non-linear techniques. A second algorithm is proposed for estimating age, which is based on a K-NN regressor and proper selection of features such as those proposed for the classification of gender. From our experiments we note that performance estimates are significantly reduced if they have been trained and tested on different databases. We have found that one of the causes is the existence of dependencies between facial features that have not been considered in the construction of classifiers. Our results demonstrate that intra-class variability can be reduced when considering the statistical dependencies between facial attributes gender, age and pose, thus improving the performance of our classifiers with a reduced computational cost.

Analysis of the role of the Spitzenkörper in fungal morphogenesis by computer simulation of apical branching in Aspergillus niger

High-resolution video microscopy, image analysis, and computer simulation were used to study the role of the Spitzenkörper (Spk) in apical branching of ramosa-1, a temperature-sensitive mutant of Aspergillus niger. A shift to the restrictive temperature led to a cytoplasmic contraction that destabilized the Spk, causing its disappearance. After a short transition period, new Spk appeared where the two incipient apical branches emerged. Changes in cell shape, growth rate, and Spk position were recorded and transferred to the fungus simulator program to test the hypothesis that the Spk functions as a vesicle supply center (VSC). The simulation faithfully duplicated the elongation of the main hypha and the two apical branches. Elongating hyphae exhibited the growth pattern described by the hyphoid equation. During the transition phase, when no Spk was visible, the growth pattern was nonhyphoid, with consecutive periods of isometric and asymmetric expansion; the apex became enlarged and blunt before the apical branches emerged. Video microscopy images suggested that the branch Spk were formed anew by gradual condensation of vesicle clouds. Simulation exercises where the VSC was split into two new VSCs failed to produce realistic shapes, thus supporting the notion that the branch Spk did not originate by division of the original Spk. The best computer simulation of apical branching morphogenesis included simulations of the ontogeny of branch Spk via condensation of vesicle clouds. This study supports the hypothesis that the Spk plays a major role in hyphal morphogenesis by operating as a VSC—i.e., by regulating the traffic of wall-building vesicles in the manner predicted by the hyphoid model.

Dynamic contrast-enhanced magnetic resonance imaging reveals stress-induced angiogenesis in MCF7 human breast tumors.

The mechanism of contrast enhancement of tumors using magnetic resonance imaging was investigated in MCF7 human breast cancer implanted in nude mice. Dynamic contrast-enhanced images recorded at high spatial resolution were analyzed by an image analysis method based on a physiological model, which included the blood circulation, the tumor, the remaining tissues, and clearance via the kidneys. This analysis enabled us to map in rapidly enhancing regions within the tumor, the capillary permeability factor (capillary permeability times surface area per voxel volume) and the fraction of leakage space. Correlation of these maps with T2-weighted spin echo images, with histopathology, and with immunohistochemical staining of endothelial cells demonstrated the presence of dense permeable microcapillaries in the tumor periphery and in intratumoral regions that surrounded necrotic loci. The high leakage from the intratumoral permeable capillaries indicated an induction of a specific angiogenic process associated with stress conditions that cause necrosis. This induction was augmented in tumors responding to tamoxifen treatment. Determination of the distribution and extent of this stress-induced angiogenic activity by contrast-enhanced MRI might be of diagnostic and of prognostic value.

Quantitative analysis of senile plaques in Alzheimer disease: observation of log-normal size distribution and molecular epidemiology of differences associated with apolipoprotein E genotype and trisomy 21 (Down syndrome).

The discovery that the epsilon 4 allele of the apolipoprotein E (apoE) gene is a putative risk factor for Alzheimer disease (AD) in the general population has highlighted the role of genetic influences in this extremely common and disabling illness. It has long been recognized that another genetic abnormality, trisomy 21 (Down syndrome), is associated with early and severe development of AD neuropathological lesions. It remains a challenge, however, to understand how these facts relate to the pathological changes in the brains of AD patients. We used computerized image analysis to examine the size distribution of one of the characteristic neuropathological lesions in AD, deposits of A beta peptide in senile plaques (SPs). Surprisingly, we find that a log-normal distribution fits the SP size distribution quite well, motivating a porous model of SP morphogenesis. We then analyzed SP size distribution curves in genotypically defined subgroups of AD patients. The data demonstrate that both apoE epsilon 4/AD and trisomy 21/AD lead to increased amyloid deposition, but by apparently different mechanisms. The size distribution curve is shifted toward larger plaques in trisomy 21/AD, probably reflecting increased A beta production. In apoE epsilon 4/AD, the size distribution is unchanged but the number of SP is increased compared to apoE epsilon 3, suggesting increased probability of SP initiation. These results demonstrate that subgroups of AD patients defined on the basis of molecular characteristics have quantitatively different neuropathological phenotypes.

Propriedades superficiais de filmes à base de gelatina

O objetivo do presente trabalho foi caracterizar as propriedades superficiais de filmes à base de gelatina. Para o qual foram elaborados filmes de: (i) Gelatina plastificado com glicerol (G) (gelatina: 5 g/100 g SFF; glicerol: 30 g/100 g de gelatina), (ii) Gelatina reforçado com montmorilhonita (G/MMT) (gelatina: 5 g/100 g SFF; glicerol: 30 g/100 g de gelatina; MMT: 5 g/100 g de gelatina) e Gelatina plastificado com citrato de acetiltributila (G/ATB) (gelatina: 5 g/100 g SFF; ATB: 50 g/100 de gelatina; lecitina de soja: 60 g/100 g de ATB; etanol: 20 g/100 g SFF). Os filmes foram produzidos mediante o uso de um aplicador automático de filmes \"Spreading\". Logo, os filmes foram submetidos a testes para determinação da espessura, umidade e propriedades óticas (brilho, cor e opacidade). Também foi caracterizada a microestrutura por microscopia eletrônica de varredura (MEV) e microscopia de força atômica (AFM); às imagens obtidas por MEV foi aplicado um analise de imagem mediante o programa Image J, para obter o valor da dimensão fractal (DF). Depois foram caracterizadas as propriedades superficiais de ângulo de contato (AC), molhabilidade ou coeficiente de espalhamento (Se), e energia livre superficial (ELS) mediante a medida do ângulo de contato pelo método da gota séssil (água: 5 µL e 1-Bromonaftaleno: 3 µL). Para o cálculo da ELS também foi aplicado o método de Owens-Wendt. Estas caracterizações foram feitas em ambos os lados do filme, lado ar e lado placa. A natureza do filme de G/ATB influenciou na umidade e as propriedades óticas, enquanto que os filmes de G e G/MMT apresentaram características similares. Em relação à microestrutura e rugosidade, o filme de G apresentou a superfície mais homogênea e lisa, contrario ao observado no filme de G/MMT, que apresentou a maior rugosidade seguida do filme de G/ATB. Foi observado que houve uma relação entre os valores de rugosidade e DF. De acordo com o valor do AC, os filmes apresentaram um caráter hidrofóbico, pois seus valores foram superiores a 65° (em ambos os lados dos filmes), na seguinte ordem: G/MMT > G > G/ATB; sendo que o Se seguiu a mesma tendência. Cabe mencionar também que não foi encontrada uma correlação significativa entre os valores de AC e rugosidade. Em função dos valores de AC, Se e ELS (especificamente a componente polar), o filme de G/ATB apresentou o menor caráter hidrofóbico, pois apresentou menores valores de AC e maiores valores de Se em comparação com os outros dois filmes. Os valores da componente polar da G/ATB foram os maiores, explicando de melhor maneira o caráter menos hidrofóbico deste filme. Pode-se concluir que os filmes à base de gelatina elaborados no presente trabalho têm propriedades hidrofóbicas (AC>65°), sendo a G/MMT o filme com melhores características hidrofóbicas.

Caracterização geométrica e mecânica de macrofibras poliméricas.

Uma grande diversidade de macrofibras poliméricas para reforço de concreto se encontram disponibilizadas hoje em dia. Por natureza estas fibras apresentam grande diversidade de características e propriedades. Estas variações afetam sua atuação como reforço no concreto. No entanto, não há normas brasileiras sobre o assunto e as metodologias de caracterização de normas estrangeiras apresentam divergências. Algumas normas definem que a caracterização do comportamento mecânico deva ser feita nos fios originais e outras que se devam utilizar métodos definidos para caracterização de materiais metálicos. A norma EN14889-2:2006 apresenta maior abrangência, mas deixa dúvidas quanto à adequação dos critérios de caracterização geométrica das fibras e não define um método de ensaio específico para sua caracterização mecânica. Assim, há a necessidade de estabelecimento de uma metodologia que permita a realização de um programa de controle de qualidade da fibra nas condições de emprego. Esta metodologia também proporcionaria uma forma de caracterização do material para estudos experimentais, o que permitiria maior fundamentação científica desses trabalhos que, frequentemente, fundamentam-se apenas em dados dos fabricantes. Assim, foi desenvolvido um estudo experimental focando a caracterização de duas macrofibras poliméricas disponíveis no mercado brasileiro. Focou-se o estudo na determinação dos parâmetros geométricos e na caracterização mecânica através da determinação da resistência à tração e avaliação do módulo de elasticidade. Na caracterização geométrica foi adotada como referência a norma europeia EN14889-2:2006. As medições do comprimento se efetuaram por dois métodos: o método do paquímetro e o método de análise de imagens digitais, empregando um software para processamento das imagens. Para a medição do diâmetro, além das metodologias mencionadas, foi usado o método da densidade. Conclui-se que o método do paquímetro, com o cuidado de esticar previamente as macrofibras, e o método das imagens digitais podem ser igualmente utilizados para medir o comprimento. Já parar determinar o diâmetro, recomenda-se o método da densidade. Quanto à caracterização mecânica, foi desenvolvida uma metodologia própria a partir de informações obtidas de outros ensaios. Assim, efetuaram-se ensaios de tração direta nas macrofibras coladas em molduras de tecido têxtil. Complementarmente, foi avaliado também o efeito do contato abrasivo das macrofibras com os agregados durante a mistura em betoneira no comportamento mecânico do material. Também se avaliou o efeito do método de determinação da área da seção transversal nos resultados medidos no ensaio de tração da fibra. Conclui-se que o método proposto para o ensaio de tração direta da fibra é viável, especialmente para a determinação da resistência à tração. O valor do módulo de elasticidade, por sua vez, acaba sendo subestimado. A determinação da área da seção da fibra através do método da densidade forneceu também os melhores resultados. Além disso, comprovou-se que o atrito das fibras com o agregado durante a mistura compromete o comportamento mecânico, reduzindo tanto a resistência quanto o módulo de elasticidade. Assim, pode-se afirmar que a metodologia proposta para o controle geométrico e mecânico das macrofibras poliméricas é adequada para a caracterização do material.

Caracterização tecnológica de minérios auríferos por análise automatizada de imagens obtidas por microscopia eletrônica de varredura.

O ouro, assim como outros bens minerais, é uma commodity, ou seja, um produto não diferenciado, com preço determinado pelo mercado internacional, sem a interferência de seus produtores. Diante desse cenário, associado à exaustão dos depósitos minerais de maiores teores, as mineradoras vêm buscando melhores formas de aproveitamento de matérias-primas minerais mais complexas quanto à extração e ao beneficiamento. Os retornos financeiros são obtidos no estrito controle da produção com redução de custos e mitigação de perdas nas operações unitárias. A caracterização tecnológica está inserida como uma abordagem multidisciplinar e fundamental para o melhor aproveitamento dos bens minerais. Possibilita um maior conhecimento do minério e das associações minerais presentes, que auxiliará no desenvolvimento das alternativas de explotação e na otimização do processo em funcionamento. Dentre os procedimentos de caracterização das associações minerais mais acurados citam-se os sistemas automatizados de análise de imagens adquiridas por microscopia eletrônica de varredura. Permitem a avaliação qualitativa ou quantitativa de grande número de partículas quanto à composição química e mineral, partição de elementos nos minerais presentes, formas de associações e liberação entre os minerais. Este estudo se concentra na caracterização de quatro amostras mineralizadas a ouro, de diferentes regiões do Brasil, pela análise automatizada de imagens e por métodos laboratoriais de separações minerais e extração hidrometalúrgica do ouro. A combinação de procedimentos laboratoriais com a análise de imagens permitiu confrontar os resultados das recuperações potenciais, fornecendo subsídios para abordagens de processo, para obtenção da máxima recuperação do ouro e para diagnosticar as características interferentes nesses processos.

Detección automática con snakes y representación 3D sobre imágenes cerebrales

Comunicación presentada en la VI Conferencia de la Asociación Española para la Inteligencia Artificial (CAEPIA'95), Alicante, 15-17 noviembre 1995.

Recolonization of mortars by endolithic organisms on the walls of San Roque church in Campeche (Mexico): A case of tertiary bioreceptivity

San Roque church (Campeche, Mexico) was built at the end of the 17th century with a micritic limestone and lime mortar in baroque style. In 2005 the church exhibited heavy biodeterioration associated with the development of extensive dark green phototrophic-based biofilms. Several cyanobacteria belonging to the order Chroococcales and lichenized fungi (Toninia nordlandica, Lobaria quercizans, Lecanora subcarnea, Cystocoleus ebeneus) were predominant in the dark biofilm samples, as revealed by DNA-based molecular techniques. In 2009, a cleaning and restoration intervention was adopted; however, after few months, microbial recolonization started to be noticeable on the painted church walls, representing an early phototrophic-based recolonization. According to molecular analysis, scanning electron microscopy observations and digital image analysis of cross sections, new phototrophic-based colonization, composed of cyanobacteria and bryophytes, developed mainly beneath the restored mortars. The intrinsic properties of the mortars, the tropical climate of Campeche and the absence of a biocide treatment in the restoration protocol influenced the recolonization of the church façades and enhanced the overall rate of deterioration in a short-term period.

Petrography, chemistry and magnetic properties of ODP Leg 115 basalts

A detailed study of the Fe-Ti oxides in four basalt samples-one from each of the four holes drilled into basement on Ocean Drilling Program Leg 115 (Sites 706, 707, 713, and 715) has been performed. Ilmenite is present only in samples from Sites 706 and 715. In the sample from Site 715, Ti-magnetite intergrowths are characteristic of subaerial (?) high-temperature oxy-exsolution; Ti-magnetite in the other three samples has experienced pervasive low-temperature oxidation to Ti-maghemite, as evidenced by the double-humped, irreversible, saturation magnetization vs. temperature (Js/T) curves. The bulk susceptibility of these samples, which are similar in terms of major element chemistry, varies by a factor of ~20 and correlates semiquantitatively with the modal abundance of Fe-Ti spinel, as determined by image analysis with an electron microprobe. The variation in Fe-Ti oxide abundance correlates with average grain size: fine-grained samples contain less Fe-Ti oxide. This prompts the speculation that the crystallization rate may also influence Fe-Ti oxide abundance.