(Table 2, page 2172) Chemical analytical data on thirty-two manganese nodules and crusts

Mn, Fe, Ca, Co, Ni, Cu, Zn, Cd, Sn, Tl, Pb and Bi have been estimated in thirty-two nodules from the Pacific, Atlantic and Indian oceans. Various features about the composition of manganese nodules are discussed: element abundances, degrees of enrichment, inter-element relationships (notably between Ni and Cu, and between Zn and Cd), regional variations and some aspects of statistical distribution.

Assessing charge contribution from thermally treated Ni foam as current collectors for Li-ion batteries

In this report we have investigated the use of Ni foam substrates as anode current collectors for Li-ion batteries. As the majority of reports in the literature focus on hydrothermal formation of materials on Ni foam followed by a high temperature anneal/oxidation step, we probed the fundamental electrochemical responses of as received Ni foam substrates and those subjected to heating at 100°C, 300°C and 450°C. Through cyclic voltammetry and galvanostatic testing, it is shown that the as received and 100°C annealed Ni foam show negligible electrochemical activity. However, Ni foams heated to higher temperature showed substantial electrochemical contributions which may lead to inflated capacities and incorrect interpretations of CV responses for samples subjected to high temperature anneals. XRD, XPS and SEM analyses clearly illustrate that the formation of electrochemically active NiO nanoparticles on the surface of the foam is responsible for this behavior. To further investigate the contribution of the oxidized Ni foam to the overall electrochemical response, we formed Co3O4 nanoflowers directly on Ni foam at 450°C and showed that the resulting electrochemical response was dominated by NiO after the first 10 charge/discharge cycles. This report highlights the importance of assessing current collector activity for active materials grown on transition metal foam current collectors for Li-ion applications.

(Table 2, page 156), The comparison of heavy elements in manganese nodules

The comparison of Mn/Fe, Co/Ni, Co/Fe, Ni/Mn, and Cu/Fe ratios is presented and it is noticed that Co/Ni and Ni/Mn ratios of nodules fairly coincide with those of coexisting sediments. This agreement suggests that Mn, Ni, and Co are accumulated in both nodules and sediments at about the same rates. According to the calculation of Somayajulu et al. similar consideration is also applicable to Cu. Results are, however, implying that Cu co-precipitates with Fe, rather than Mn.

Geochemistry, carbon isotope ratio and radiocarbon ages of sediment core GIK1093-2 from Bornholm Basin, Baltic Sea

Concentrations of Cd, Pb, Zn, Cu, Co, Ni, Fe, and Al203, water content, the amounts of organic carbon, the ratio of 13C/12C and the 14C-activity of the organic fraction were determined with sediment depth from a 34 cm long box-core from the Bornholm Basin (Baltic Sea). The average sedimentation rate was 2.4 mm/yr. The upper portion of the core contained increasing amounts of 14C-inactive organic carbon, and above 3 cm depth, man-made 14C from atomic bomb tests. The concentrations of the heavy metals Cd, Pb, Zn, and Cu increase strongly towards the surface, while other metals, as Fe, Ni and Co remain almost unchanged. This phenomenon is attributed to anthropogenic influences. A comparison of the Kieler Bucht, the Bornholm and the Gotland Basins shows that today the anthropogenic addition of Zn is about 100 mg/m**2 yr in all three basins. The beginning of this excess of Zn, however, is delayed by about 20 years in, the Bornholm Basin and by about 40 years in the Gotland Basin. It is suggested that SW-NE transport of these anthropogenically mobilized metals may be related to periodic bottom water renewal in the Baltic Sea sedimentary basins.

(Table 2, Page 270) Average chemical composition of manganese nodules and crust collected at different localities the Pacific Ocean

Considerable regional variations in the chemical composition of manganese nodules from a wide range of the Pacific Ocean have been observed. These variations can be more exactly expressed in terms of inter-element relationships. In particular, Cu-Mn and Cu-Ni associations reveal that Cu content in pelagic nodules increases rapidly in proportion to those of Mn or Ni. In nodules from continental borderland and hemipelagic areas, even if Mn or Ni contents increase, that of Cu increases only slightly. It is suggested that the considerable chemical differences within individual nodules and between nodules from the same site, at a limited pelagic area where there is no marked change in depositional conditions of nodules, are due to the role of hydrolyzable trace elements in the formation of nodules.

Fútbol y redes sociales. Análisis de la gestión de Relaciones Públicas 2.0 por los clubes de fútbol

Las relaciones públicas se configuran como una actividad esencial en la gestión de la comunicación con los públicos de los clubes de fútbol ya que son muy activos y su grado de reactividad es alto. Con este texto se analiza el papel que desempeñan las redes sociales en los clubes de fútbol que poseen mayor número de ingresos. Para ello, se desarrolla una metodología que estudia qué presencia tienen en las redes sociales, el número de seguidores, qué grado de interacción se produce entre clubes y públicos y los contenidos y las temáticas de los textos de las redes sociales. Los resultados muestran un público activo pero con intervenciones relacionadas con los resultados futbolísticos y una gestión comunicativa unidireccional por parte de los clubes.

Fabrication and evaluation of NiO/Y₂O₃-stabilized-ZrO₂ hollow fibers for anode-supported micro-tubular solid oxide fuel cells

<p>In this work NiO/3mol% Y₂O₃-ZrO₂ (3YSZ) and NiO/8mol% Y₂O₃-ZrO₂ (8YSZ) hollow fibers were prepared by phase-inversion. The effect of different kinds of YSZ (3YSZ and 8YSZ) on the porosity, electrical conductivity, shrinkage and flexural strength of the hollow fibers were systematically evaluated. When compared with Ni-8YSZ the porosity and shrinkage of Ni-3YSZ hollow fibers increases while the electrical conductivity decreases, while at the same time also exhibiting enhanced flexural strength. Single cells with Ni-3YSZ and Ni-8YSZ hollow fibers as the supported anode were successfully fabricated showing maximum power densities of 0.53 and 0.67Wcm^-2 at 800°C, respectively. Furthermore, in order to improve the cell performance, a Ni-8YSZ anode functional layer was added between the electrolyte and Ni-YSZ hollow fiber. Here enhanced peak power densities of 0.79 and 0.73Wcm^-2 were achieved at 800°C for single cells with Ni-3YSZ and Ni-8YSZ hollow fibers, respectively.</p>

Synthesis of Pr_0.6Sr_0.4FeO_3-δ-xCe_0.9Pr_0.1O_2-δ cobalt-free composite cathodes by a one-pot method for intermediate-temperature solid oxide fuel cells

<p>Cobalt-free composite cathodes consisting of Pr_0.6Sr_0.4FeO_3-δ-xCe_0.9Pr_0.1O_2-δ (PSFO-xCPO, x = 0-50 wt%) have been synthesized using a one-pot method. X-ray diffraction, scanning electron microscopy, thermal expansion coefficient, conductivity, and polarization resistance (R _P) have been used to characterize the PSFO-xCPO cathodes. Furthermore the discharge performance of the Ni-SSZ/SSZ/GDC/PSFO-xCPO cells has been measured. The experimental results indicate that the PSFO-xCPO composite materials fully consist of PSFO and CPO phases and posses a porous microstructure. The conductivity of PSFO-xCPO decreases with the increase of CPO content, but R _P of PSFO-40CPO shows the smallest value amongst all the samples. The power density of single cells with a PSFO-40CPO composite cathode is significantly improved compared with that of the PSFO cathode, exhibiting 0.43, 0.75, 1.08 and 1.30 W cm^-2 at 650, 700, 750 and 800 °C, respectively. In addition, single cells with the PSFO-40CPO composite cathode show a stable performance with no obvious degradation over 100 h when operating at 750 °C.</p>

The Effect of Residence Time on the Tensile Properties of Superelastic and Thermal Activated Ni-Ti Orthodontic Wires

Since the 1980s, different devices based on superelastic alloys have been developed to fulfill orthodontic applications. Particularly in the last decades several researches have been carried out to evaluate the mechanical behavior of Ni-Ti alloys, including their tensile, torsion and fatigue properties. However, studies regarding the dependence of elastic properties on residence time of Ni-Ti wires in the oral cavity are scarce. Such approach is essential since metallic alloys are submitted to mechanical stresses during orthodontic treatment as well as pH and temperature fluctuations. The goal of the present contribution is to provide elastic stress-strain results to guide the orthodontic choice between martensitic thermal activated and austenitic superelastic Ni-Ti alloys. From the point of view of an orthodontist, the selection of appropriate materials and the correct maintenance of the orthodontic apparatus are essential needs during clinical treatment. The present work evaluated the elastic behavior of Ni-Ti alloy wires with diameters varying from 0.014 to 0.020 inches, submitted to hysteresis tensile tests with 8% strain. Tensile tests were performed after periods of use of 1, 2 and 3 months in the oral cavity of patients submitted to orthodontic treatment. The results from the hysteresis tests allowed to exam the strain range covered by isostress lines upon loading and unloading, as well as the residual strain after unloading for both superelastic and thermal activated Ni-Ti wires. Superelastic Ni-Ti wires exhibited higher load isostress values compared to thermal activated wires. It was found that such differences in the load isostress values can increase with increasing residence time.

Boletin POLIS. Vol. 2 No. 2 - Mayo de 2007

Construyendo herramientas para el seguimiento de las finanzas públicas territoriales del Valle del Cauca y Cali - Relaciones público-privadas en contratos de concesión y estabilidad jurídica. - Educar para la intervención social: retos de la academia. - El futuro de la Sobretasa a la gasolina y la financiación del Sistema Integrado de Transporte Masivo.

Boletin POLIS Vol. 2 No.3 - Febrero de 2008

Contiene: Temas fundamentales para el Valle del Cauca y Cali 2008-2011 - Fragmentación partidaria y gobierno dividido estabilidad política? Cali 2008-2011 - Mercado de trabajo e inquietudes de género Cali 1990-2007 - Epidemiología del VIH/SIDA en Cali: Una problemática de Salud Pública

Votar, ni con temblor

Fondo Margaritainés Restrepo

The Effect of Residence Time on the Tensile Properties of Superelastic and Thermal Activated Ni-Ti Orthodontic Wires

Since the 1980s, different devices based on superelastic alloys have been developed to fulfill orthodontic applications. Particularly in the last decades several researches have been carried out to evaluate the mechanical behavior of Ni-Ti alloys, including their tensile, torsion and fatigue properties. However, studies regarding the dependence of elastic properties on residence time of Ni-Ti wires in the oral cavity are scarce. Such approach is essential since metallic alloys are submitted to mechanical stresses during orthodontic treatment as well as pH and temperature fluctuations. The goal of the present contribution is to provide elastic stress-strain results to guide the orthodontic choice between martensitic thermal activated and austenitic superelastic Ni-Ti alloys. From the point of view of an orthodontist, the selection of appropriate materials and the correct maintenance of the orthodontic apparatus are essential needs during clinical treatment. The present work evaluated the elastic behavior of Ni-Ti alloy wires with diameters varying from 0.014 to 0.020 inches, submitted to hysteresis tensile tests with 8% strain. Tensile tests were performed after periods of use of 1, 2 and 3 months in the oral cavity of patients submitted to orthodontic treatment. The results from the hysteresis tests allowed to exam the strain range covered by isostress lines upon loading and unloading, as well as the residual strain after unloading for both superelastic and thermal activated Ni-Ti wires. Superelastic Ni-Ti wires exhibited higher load isostress values compared to thermal activated wires. It was found that such differences in the load isostress values can increase with increasing residence time.

Nickel isotope fractionation during laterite Ni ore smelting and refining: implications for tracing the sources of Ni in smelter-affected soils

Nickel isotope ratios were measured in ores, fly ash, slags and FeNi samples from two metallurgical plants located in the Goiás State, Brazil (Barro Alto, Niquelândia). This allowed investigating the mass-dependent fractionation of Ni isotopes during the Ni-laterite ore smelting and refining. Feeding material exhibits a large range of δ60Ni values (from 0.02 ± 0.10 ‰ to 0.20 ± 0.05 ‰, n=7), explained by the diversity of Ni-bearing phases, and the average of δ60Nifeeding materials was found equal to 0.08 ± 0.08‰ (2SD, n=7). Both δ60Ni values of fly ash (δ60Ni = 0.07 ± 0.07‰, n=10) and final FeNi produced (0.05 ± 0.02 ‰, n=2) were not significantly different from the feeding materials ones. These values are consistent with the very high production yield of the factories. However, smelting slags present the heaviest δ60Ni values of all the smelter samples, with δ60Ni ranging from 0.11 ± 0.05 ‰ to 0.27 ± 0.05 ‰ (n=8). Soils were also collected near and far from the Niquelândia metallurgical plant, to evaluate the potential of Ni isotopes for tracing the natural vs anthropogenic Ni in soils. The Ni isotopic composition of the non-impacted topsoils developed on ultramafic rocks ranges from -0.26 ± 0.09 ‰ to -0.04 ± 0.05 ‰ (n=20). On the contrary, the Ni isotopic composition of the non-ultramafic topsoils, collected close to the plant, exhibit a large variation of δ60Ni, ranging from -0.19 ± 0.13 ‰ up to 0.10 ± 0.05 ‰ (n=4). This slight but significant enrichment in heavy isotopes highlight the potential impact of smelting activity in the surrounding area, as well as the potential of Ni isotopes for discerning anthropogenic samples (heavier δ60Ni values) from natural ones (lighter δ60Ni values). However, given the global range of published δ60Ni values (from -1.03 to 2.5 ‰) and more particularly those associated to natural weathering of ultramafic rocks (from -0.61 to 0.32‰), the use of Ni isotopes for tracing environmental contamination from smelters will remain challenging.