Vitrocerâmicas para blindagens balísticas

The use of ceramic materials in ballistic armor is considerable. Such materials can be very harder and lighter than metallic materials commonly used and it presents advantages to replace metallic materials when necessary toughness can be achieved. However, as SiC and Al2O3 ceramic, traditionally used for shielding, still have high manufacturing cost or low density do not have enough to shield applications such as aircraft. An alternative is the glass-ceramics, ceramics obtained by controlled crystallization of glasses, whose properties can be adjusted by choosing the chemical composition of glass, heat treatment of crystallization and special treatments such as ion exchange on the surface, resulting in increased mechanical strength . The objective of this project is to study the kinetics of crystallization of a glass composition based on cordierite (2MgO.2Al2O3.5SiO2), low density and high hardness, for the manufacture of glass-ceramics for ballistic tests. Shown in this report are results of heat treatment of crystallization and characterization by thermal analysis (DSC) glass obtained previously, indicating uneven distribution of crystals, and drying, weighing, mixing of raw materials and a new fusion of glass, the same composition

Síntese e caracterização de ferritas de manganês e zinco visando aplicação como agente de contraste em diagnóstico médico

This work aims to synthesize the manganese and zinc ferrite, by the polymeric precursor method, in order to obtain materials with appropriate characteristics for the application in medical diagnosis techniques. The manganese and zinc ferrite powders with the composition of Mn(1-x)ZnxFe2O4, where x=0,23, were prepared and calcined in air at different times and temperatures. The X-ray diffraction (XRD) data show that the sample calcined at 400°C crystallize as ferrite (monophase), but in an inverted spinel structure (high content of iron occupying manganese tetrahedral site and manganese occupying the iron octahedral site). The samples calcined at temperatures between 600°C and 900°C shows the secondary phase of hematite and the sample calcined at 1100oC shows to be monophase in ferrite with normal spinel structure. The monophase powders of ferrite showed a reduction in the surface area and an increasing in the pore size for higher calcination temperatures. The magnetic analysis show that the sample calcined at 400°C presents satisfactory magnetization at room temperature, however, it behaves as diamagnetic material at low temperatures (10K). The powder containing hematite, without the partial substitution of iron ions by manganese, showed to have low transition temperature, and consequently low magnetization at room temperature. The hematite, when partially substituted, provides materials with irregular magnetization at the saturation region. The powder calcined at 1100°C shows high magnetization either at room temperature or low temperature (10K)

Efeito do treinamento com pesos nos distúrbios do sono e na qualidade de vida de pacientes com demência de Alzheimer

The Alzheimer's dementia (AD) is the most prevalent form of dementia in the elderly. Among the harmful changes arising from the DA, there may be sleep disturbance and impaired quality of life. Physical activity is an important non-pharmacological feature that would provide positive effects for the treatment of disease. However, there are still few studies that clarify the effects of resistance training in this population. Thus, the present study has as objective analyzes the effects of the resistance training in sleep disturbance and quality of life of patients with AD. Participated in this study 22 patients with clinical diagnosis of AD divided into two groups: Training Group (TG) and Social Interaction Group (SIG). The subjects of TG underwent a resistance training protocol, appropriate to the individual conditions, during three days no consecutive in the week, with duration of 60 minutes each session, for 16 weeks. The SIG won't participate in any systematized physical activity, but they realized other activities, such as reading, poetry, hiking and painting, among others. This protocol also was realized three times in week for 16 weeks, with duration of 60 minutes each session. Both groups were assessed at the beginning of the program and after 16 weeks. For the assessment of sleep disturbance was used the Mini Sleep Questionnaire and to assess of quality of life was used the Scale for Assessment of Quality of Life in Alzheimer's disease (QL), versions: patient, caregiver, family and the final score. Due to the scalar nature of the data and small sample, all variables were analyzed by nonparametric statistics. The U-Mann Whitney test, Wilcoxon test and Spearman correlation test was used, except for the Modified Baecke... (Complete abstract click electronic access below)

Caracterização funcional da proteína XAC1201 envolvida na patogenicidade de Xanthomonas citri subsp. citri

Pós-graduação em Agronomia (Genética e Melhoramento de Plantas) - FCAV

Microbiota contaminante em bebidas lácteas fermentadas comerciais

Lately, the acceptability of fermented dairy beverages has been increased, due to the nutritional benefits, the practical consumption and the low cost of product for the manufacturers, and consequently for final market price to the consumers. During the manufacturing process, these products can be susceptible to microbiological contamination. The present study investigated the contaminant microbiota in fermented dairy beverages produced by small- and medium-sized companies, by means of analyses on moulds and yeasts counting, determination of the Most Probable Number (MPN) of total and thermo tolerant coliforms, Escherichia coli and Salmonella spp. detection, and determination of pH value. In spite of the absence of Salmonella spp., a high counts of yeasts and moulds were found, and E. coli was detected in five samples (16.67 %); and the sample were classified as “products in poor sanitary conditions”, because they showed thermo-tolerant coliforms counting higher than the standard established by the legislation in force. Therefore, quality programs such as Good Manufacturing Practices (GMP) and Hazard Analysis and Critical Control Points (HACCP) should be employed to prevent any contamination risk, in order to provide safe products to consumers.

Avaliação audiológica, metabólica e de qualidade de vida no indivíduo jovem com zumbido usuário de estéreo pessoal

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Análise de SNPs do DNA mitocondrial em indivíduos residentes no estado do Espírito Santo para aplicação na Identificação Humana

Pós-graduação em Biotecnologia - IQ

In vitro comparison of the force degradation of orthodontic intraoral elastics from different compositions

The synthetic intermaxillary elastic emerged as an alternative for clinical use in patients with latex sensitivity. However, there are disagreements about this elastic protocol use according to the force degradation. The aim of this study was to evaluate, in vitro, the forces generated by latex and synthetic elastics over time. Material and methods: Sample size of 840 elastics were used (420 latex and 420 synthetic), delivering medium strength (Dental Morelli®) with internal diameter of 1/8", 3/16", 1/4" and 5/16". The elastics were randomly divided into 7 groups according to the time of the force measuring and immersed into distilled water at 37°C. To measure the force in each group, the elastics were stretched in six progressive increases of 100% of its internal diameter with the aid of a testing machine Emic and measured up to 72 hours. Data were analyzed with SPSS 16.0, using one-way analysis of variance (ANOVA). Results: Immediate force level of synthetic elastics was statistically higher than latex elastics in all strains, for the same size. However, the latex elastics mean forceslightly decreased over time, while the synthetic elastics presented an abrupt decrease. Conclusion: In view of these findings, Sudanese homemade alcoholic beverages cause oral epithelial atypical changes, which lead to oral precancerous and cancerous lesions. OEFC is a useful procedure for detection and assessment of oral ET.

In vitro comparison of the force degradation of orthodontic intramural elastic from different compositions

Introduction and Objective: The synthetic intermaxillary elastic emerged as an alternative for clinical use in patients with latex sensitivity. However, there are disagreements about this elastic protocol use according to the force degradation. The aim of this study was to evaluate, in vitro, the forces generated by latex and synthetic elastics over time. Material and methods: Sample size of 840 elastics were used (420 latex and 420 synthetic), delivering medium strength (Dental Morelli®) with internal diameter of 1/8”, 3/16”, 1/4” and 5/16”. The elastics were randomly divided into 7 groups according to the time of the force measuring and immersed into distilled water at 37°C. To measure the force in each group, the elastics were stretched in six progressive increases of 100% of its internal diameter with the aid of a testing machine Emic and measured up to 72 hours. Data were analyzed with SPSS 16.0, using one-way analysis of variance (ANOVA). Results: Immediate force level of synthetic elastics was statistically higher than latex elastics in all strains, for the same size. However, the latex elastics mean force slightly decreased over time, while the synthetic elastics presented an abrupt decrease. Conclusion: The synthetic elastic presented severe force degradation, jeopardizing the cost-benefit ratio, which indicates a higher replacement frequency. The latex elastic showed better mechanical performance in comparison to synthetic ones.

Comparison of compressive strength between three different plates for mandibular angle fractures fixation

The present study aims to compare three types of internal fixation for fractures of the mandibular angle. Mechanical testing was performed on replicas of polyurethane hemimandibles sectioned at the angle region to simulate a fracture and fixed with three different hardwares. Fixation devices enrolled on this survey included the grid plates with and without an intermediate bar and the method described by Champy and colleagues in 1978 and the sample consisted of 10 hemimandibles for each group. Vertical loadings were applied on each hemimandible and recorded after a vertical displacement of 3 and 5 mm. Statistical analysis was made by means of the variance analysis (ANOVA) and the Duncan test with a significance level of 5%. The Champy technique showed a statistically significant increased resistance when compared to the grid plates after vertical displacements of 3 and 5 mm. The results of this survey suggest that the Champy technique, when compared to the grid plate positioned at the middle of the mandibular bone (placement site selected for this study), is more resistant than the grid plate and that the inclusion or not of an intermediate bar to the grid plates does not improve its resistance after linear vertical loadings.

Análise de parâmetros de qualidade da água para consumo humano

The Current work to assess the capacity of water potability samples for that, we used seven different brands of mineral water, bought locally, and also collected seven samples of public drinking fountains located in different places on campus headquarters of the State University of Maringá. The parameters analyzed were presence of fecal and total coliform, turbidity, color and compounds with UV-absorption at 254 nm. On the analysis of coliforms, two brands of mineral water and four samples of drinkers showed presence of total coliform, but no analysis indicated the presence of fecal coliforms. In the turbidity parameter, all samples were within the limits allowed by law, for both cases. No apparent color attribute, two samples of mineral water and a sample of drinking were outside the range required by law. Finally, the determination of UV showed the values of light absorption of each sample at a wavelength of 254nm, however, does not yet exist in Brazil a regulation on this parameter. With such analysis, it was possible to compare the results with current legislation. After these findings, it appears that more stringent hygienic practices should be adopted throughout the processing of mineral water as drinking in public. It is also necessary for greater oversight over the other parameters for determining the quality of water.

Tumor mamário canino: estudo in vitro, imunomarcação e ação da doxorrubicina

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Influência de tratamentos termo-mecânicos na estrutura e microestrutura da liga Ti-10%pNi obtida por fusão a arco

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Influência do espaçamento do feixe de laser Nd: YAG na obtenção de óxidos e nitretos na superfície do titânio em pressão atmosférica

Neste trabalho investigou-se a modificação de superfície do titânio pela irradiação com feixe de Laser Nd:YAG. Os parâmetros do laser como a potência, o comprimento de onda, a frequência, a velocidade de varredura e a área de exposição foram mantidos constantes, exceto o espaçamento da matriz, o qual foi de 0,01 e 0,02 mm. A caracterização da superfície foi realizada por Microscopia Eletrônica de Varredura (MEV) e Difração de Raios X (DRX), sendo que os espectros foram refinados pelo método Rietveld. Pela análise de MEV, observou-se uma mudança na topografia, obtendo uma superfície rugosa produzida pelo fenômeno de ablação. As análises por Rietveld dos espectros de difração de raios X detectaram TiN, Ti2N, TiO2 (anatásio e rutilo), sendo que a amostra com espaçamento 0,01 mm apresentou uma maior quantidade de óxidos e nitretos. Isso pode ser devido à sobreposição do feixe, induzindo à formação de uma superfície com maior estabilidade termodinâmica. Os óxidos e nitretos obtidos são de grande importância, pois são responsáveis por produzir uma maior interação entre o osso-implante.

Management of accidental swallowing in implant dentistry

This report describes a protocol for managing the accidental swallowing of dental instruments in implant dentistry, illustrated by a patient who accidentally swallowed a hexagonal wrench. The first step was to refer the patient to the medical emergency hospital service for radiographic and clinical evaluation. The hexagonal wrench was located in the stomach and was immediately removed with an endoscopic procedure. The gastric mucosa was sampled via biopsy and the sample submitted to the urease test, which was positive for Helicobacter pylori. Triple treatment was instituted for gastritis caused by H pylori to avoid exposing the patient to unnecessary risk. Removal of a foreign body by means of an endoscopic procedure constitutes a safe and effective treatment.