Coupled scalar fields oscillons and breathers in some lorentz violating scenarios

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Michelson interferometer vibrometer using self-correcting synthetic-heterodyne demodulation

Synthetic-heterodyne demodulation is a useful technique for dynamic displacement and velocity detection in interferometric sensors, as it can provide an output signal that is immune to interferometric drift. With the advent of cost-effective, high-speed real-time signal-processing systems and software, processing of the complex signals encountered in interferometry has become more feasible. In synthetic heterodyne, to obtain the actual dynamic displacement or vibration of the object under test requires knowledge of the interferometer visibility and also the argument of two Bessel functions. In this paper, a method is described for determining the former and setting the Bessel function argument to a set value, which ensures maximum sensitivity. Conventional synthetic-heterodyne demodulation requires the use of two in-phase local oscillators; however, the relative phase of these oscillators relative to the interferometric signal is unknown. It is shown that, by using two additional quadrature local oscillators, a demodulated signal can be obtained that is independent of this phase difference. The experimental interferometer is aMichelson configuration using a visible single-mode laser, whose current is sinusoidally modulated at a frequency of 20 kHz. The detected interferometer output is acquired using a 250 kHz analog-to-digital converter and processed in real time. The system is used to measure the displacement sensitivity frequency response and linearity of a piezoelectric mirror shifter over a range of 500 Hz to 10 kHz. The experimental results show good agreement with two data-obtained independent techniques: the signal coincidence and denominated n-commuted Pernick method.

Kinematic analysis of forelimb and hind limb joints in clinically healthy sheep

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Computer graphics applied to anatomy: a study of two bio-cad modeling methods on finite element analysis of human edentulous hemi-mandible

Modeling is a step to perform a finite element analysis. Different methods of model construction are reported in literature, as the Bio-CAD modeling. The purpose of this study was to perform a model evaluation and application using two methods of Bio-CAD modeling from human edentulous hemi-mandible on the finite element analysis. From CT scans of dried human skull was reconstructed a stereolithographic model. Two methods of modeling were performed: STL conversion approach (Model 1) associated to STL simplification and reverse engineering approach (Model 2). For finite element analysis was used the action of lateral pterygoid muscle as loading condition to assess total displacement (D), equivalent von-Mises stress (VM) and maximum principal stress (MP). Two models presented differences on the geometry regarding surface number (1834 (model 1); 282 (model 2)). Were observed differences in finite element mesh regarding element number (30428 nodes/16683 elements (model 1); 15801 nodes/8410 elements (model 2). D, VM and MP stress areas presented similar distribution in two models. The values were different regarding maximum and minimum values of D (ranging 0-0.511 mm (model 1) and 0-0.544 mm (model 2), VM stress (6.36E-04-11.4 MPa (model 1) and 2.15E-04-14.7 MPa (model 2) and MP stress (-1.43-9.14 MPa (model 1) and -1.2-11.6 MPa (model 2). From two methods of Bio-CAD modeling, the reverse engineering presented better anatomical representation compared to the STL conversion approach. The models presented differences in the finite element mesh, total displacement and stress distribution.

Geometrical parameter analysis of a high-sensitivity fiber optic angular displacement sensor

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Nano-displacement measurements of a new piezoelectric flextensional actuator by using a high dynamic range interferometry homodyne method

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

The crystal field strength parameter and the maximum splitting of the 7F1 manifold of the Eu3+ ion in oxides

We examine, from both the experimental and theoretical point of view, the behavior of the maximum splitting ΔE, of the 7F1 manifold of the Eu3+ ion as a function of the so-called crystal field strength parameter, Nv, in a series of oxides. In connection with the original theory that describes the relation between ΔE and Nv, a more consistent procedure to describe this relation is presented for the cases of small total angular momentum J. Good agreement is found between theory and experiment. © 1995.

A 3-D finite element study of the influence of crown-implant ratio on stress distribution

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Influence of occlusal contact area on cusp defection and stress distribution

The purpose of this study was to evaluate the effect of occlusal contact area for loading on the cuspal defection and stress distribution in a first premolar restored with a high elastic modulus restorative material. The Rhinoceros 4.0 software was used for modeling the three-dimensional geometries of dental and periodontal structures and the inlay restoration. Thus, two different models, intact and restored teeth with three occlusal contact areas, 0.1, 0.5 and 0.75 mm(2), on enamel at the occlusal surface of buccal and lingual cusps. Finite element analysis (FEA) was performed with the program ANSYS (Workbench 13.0), which generated a mesh with tetrahedral elements with greater refinement in the regions of interest, and was constrained at the bases of cortical and trabecular bone in all axis and loaded with 100 N normal to each contact area. To analysis of maximum principal stress, the smaller occlusal contact area showed greater compressive stress in region of load application for both the intact and inlay restored tooth. However, tensile stresses at the occlusal isthmus were similar for all three tested occlusal contact areas (60 MPa). To displacement of the cusps was higher for teeth with inlay (0.46-0.48 mm). For intact teeth, the smaller contact area showed greater displacement (0.10 mm). For teeth with inlays, the displacement of the cusps were similar in all types of occlusal area. Cuspal displacement was higher in the restored tooth when compared to the intact tooth, but there were no significant variations even with changes in the occlusal contact area. RELEVANCE CLINICAL: Occlusal contacts have a great influence on the positioning of teeth being able to maintain the position and stability of the mandible. Axial loads would be able to generate more uniform stress at the root presenting a greater concentration of load application in the point and the occlusal surface. Thus, is necessary to analyze the relationship between these occlusal contacts as dental wear and subsequent occlusal interferences.

Three-dimensional finite element analysis of anterior single implant-supported prostheses with different bone anchorages

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Vibração incidente sobre o corpo inteiro do operador de trator agrícola ensaiado em pista de vibração com diferentes lastros, velocidades e pressões de inflação dos pneus

Pós-graduação em Agronomia (Energia na Agricultura) - FCA

Atributos químicos e físicos de um argissolo cultivado com Panicum maximum Jacq. cv. IPR-86 Milênio, sob lotação rotacionada e adubado com nitrogênio

A avaliação dos atributos químicos e físicos do solo é necessária em estudos que exploram intensivamente os sistemas de pastejo. No presente trabalho, objetivou-se avaliar as variações nos atributos físicos e químicos de um Argissolo cultivado com capim-milênio, sob pastejo, no intervalo compreendido entre outubro/2001 e maio/2002, no quinto ano de aplicação sucessiva das seguintes doses de N: 0, 150, 300 e 450 kg ha-1. Após os cinco anos de aplicação de 450 kg ha-1 de N, o teor de MO aumentou em 5 g dm-3, o que resultou em aumento da CTC. No período de outubro/2001 a maio/2002 houve diminuição nos valores de pH e de V com a aplicação de N. A densidade do solo variou pouco com a adubação nitrogenada; a percentagem de microporos aumentou e a de macroporos diminuiu na camada de 0-5 cm com o aumento das doses de N, mas a porosidade total permaneceu constante; e a resistência à penetração, quando o solo apresentava 90 g kg-1 de água, não foi afetada pelas doses de N e não foi restritiva ao crescimento das plantas.

The use of nonlinear programming as a tool for maximum profit feed formulation of broilers

The purpose of this study was to compare linear and nonlinear programming models for feed formulation, for maximum profit, considering the real variation in the prices of the corn, soybean meal and broilers during the period from January of 2008 to October of 2009, in the São Paulo State, Brazil. For the nonlinear formulation model, it was considered the following scenarios of prices: a) the minimum broiler price and the maximum prices of the corn and soybean meal during the period, b) the mean prices of the broiler, corn and soybean meal in the period and c) the maximum broiler price and the minimum prices of the corn and soybean meal, in the considered period; while for the linear formulation model, it was considered just the prices of the corn and the soybean. It was used the Practical Program for Feed Formulation 2.0 for the diets establishment. A total of 300 Cobb male chicks were randomly assigned to the 4 dietary treatments with 5 replicate pens of 15 chicks each. The birds were fed with a starter diet until 21 d and a grower diet from 22 to 42 d of age, and they had ad libitum access to feed and water, on floor with wood shavings as litter. The broilers were raised in an environmentally-controlled house. Body weight, body weight gain, feed intake, feed conversion ratio and profitability (related to the prices variation of the broilers and ingredients) were obtained at 42 d of age. It was found that the broilers fed with the diet formulated with the linear model presented the lowest feed intake and feed conversion ratio as compared with the broilers fed with diets from nonlinear formulation models. There were no significant differences in body weight and body weight gain among the treatments. Nevertheless, the profitabilities of the diets from the nonlinear model were significantly higher than that one from the linear formulation model, when the corn and soybean meal prices were near or below their average values for the studied period, for any broiler chicken price.

Determinação do posicionamento ótimo de apoios em pontes

This paper presents a study to determine the optimal support positions in bridges, as well as the optimal relation between the spans of beams, aiming both the reduction and the unifirmization of the efforts in these structures. The mathematical problem is formulated in order to minimize the maximum bending moments, taking the coordinate of each internal support as design variable. To take into account possible location limitations, size constraints are also considered in the formulation. The software developed based on this study determines the efforts in each support for load shifting along the structure by the usage of the Displacement Method, and the optimization is performed with a mathematical programming technique. The structures analyzed from the computational implementation of the idealized model point to the validation and efficiency of the proposed procedure.

Interpretação racional do ensaio DPL

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)