Reliability driven reconfiguration of rural power distribution systems

This paper presents a reliability-based reconfiguration methodology for power distribution systems. Probabilistic reliability models of the system components are considered and Monte Carlo method is used while evaluating the reliability of the distribution system. The reconfiguration is aimed at maximizing the reliability of the power supplied to the customers. A binary particle swarm optimization (BPSO) algorithm is used as a tool to determine the optimal configuration of the sectionalizing and tie switches in the system. The proposed methodology is applied on a modified IEEE 13-bus distribution system.

Power sharing and stability enhancement of an autonomous microgrid with inertial and non-inertial DGs with DSTATCOM

This paper proposes a method of enhancing system stability with a distribution static compensator (DSTATCOM) in an autonomous microgrid with multiple distributed generators (DG). It is assumed that there are both inertial and non-inertial DGs connected to the microgrid. The inertial DG can be a synchronous machine of smaller rating while inertia less DGs (solar) are assumed as DC sources. The inertia less DGs are connected through Voltage Source Converter (VSC) to the microgrid. The VSCs are controlled by either state feedback or current feedback mode to achieve desired voltage-current or power outputs respectively. The power sharing among the DGs is achieved by drooping voltage angle. Once the reference for the output voltage magnitude and angle is calculated from the droop, state feedback controllers are used to track the reference. The angle reference for the synchronous machine is compared with the output voltage angle of the machine and the error is fed to a PI controller. The controller output is used to set the power reference of the synchronous machine. The rate of change in the angle in a synchronous machine is restricted by the machine inertia and to mimic this nature, the rate of change in the VSCs angles are restricted by a derivative feedback in the droop control. The connected distribution static compensator (DSTATCOM) provides ride through capability during power imbalance in the microgrid, especially when the stored energy of the inertial DG is not sufficient to maintain stability. The inclusion of the DSATCOM in such cases ensures the system stability. The efficacies of the controllers are established through extensive simulation studies using PSCAD.

Evaluating information systems

The book within which this chapter appears is published as a research reference book (not a coursework textbook) on Management Information Systems (MIS) for seniors or graduate students in Chinese universities. It is hoped that this chapter, along with the others, will be helpful to MIS scholars and PhD/Masters research students in China who seek understanding of several central Information Systems (IS) research topics and related issues. The subject of this chapter - ‘Evaluating Information Systems’ - is broad, and cannot be addressed in its entirety in any depth within a single book chapter. The chapter proceeds from the truism that organizations have limited resources and those resources need to be invested in a way that provides greatest benefit to the organization. IT expenditure represents a substantial portion of any organization’s investment budget and IT related innovations have broad organizational impacts. Evaluation of the impact of this major investment is essential to justify this expenditure both pre- and post-investment. Evaluation is also important to prioritize possible improvements. The chapter (and most of the literature reviewed herein) admittedly assumes a blackbox view of IS/IT1, emphasizing measures of its consequences (e.g. for organizational performance or the economy) or perceptions of its quality from a user perspective. This reflects the MIS emphasis – a ‘management’ emphasis rather than a software engineering emphasis2, where a software engineering emphasis might be on the technical characteristics and technical performance. Though a black-box approach limits diagnostic specificity of findings from a technical perspective, it offers many benefits. In addition to superior management information, these benefits may include economy of measurement and comparability of findings (e.g. see Part 4 on Benchmarking IS). The chapter does not purport to be a comprehensive treatment of the relevant literature. It does, however, reflect many of the more influential works, and a representative range of important writings in the area. The author has been somewhat opportunistic in Part 2, employing a single journal – The Journal of Strategic Information Systems – to derive a classification of literature in the broader domain. Nonetheless, the arguments for this approach are believed to be sound, and the value from this exercise real. The chapter drills down from the general to the specific. It commences with a highlevel overview of the general topic area. This is achieved in 2 parts: - Part 1 addressing existing research in the more comprehensive IS research outlets (e.g. MISQ, JAIS, ISR, JMIS, ICIS), and Part 2 addressing existing research in a key specialist outlet (i.e. Journal of Strategic Information Systems). Subsequently, in Part 3, the chapter narrows to focus on the sub-topic ‘Information Systems Success Measurement’; then drilling deeper to become even more focused in Part 4 on ‘Benchmarking Information Systems’. In other words, the chapter drills down from Parts 1&2 Value of IS, to Part 3 Measuring Information Systems Success, to Part 4 Benchmarking IS. While the commencing Parts (1&2) are by definition broadly relevant to the chapter topic, the subsequent, more focused Parts (3 and 4) admittedly reflect the author’s more specific interests. Thus, the three chapter foci – value of IS, measuring IS success, and benchmarking IS - are not mutually exclusive, but, rather, each subsequent focus is in most respects a sub-set of the former. Parts 1&2, ‘the Value of IS’, take a broad view, with much emphasis on ‘the business Value of IS’, or the relationship between information technology and organizational performance. Part 3, ‘Information System Success Measurement’, focuses more specifically on measures and constructs employed in empirical research into the drivers of IS success (ISS). (DeLone and McLean 1992) inventoried and rationalized disparate prior measures of ISS into 6 constructs – System Quality, Information Quality, Individual Impact, Organizational Impact, Satisfaction and Use (later suggesting a 7th construct – Service Quality (DeLone and McLean 2003)). These 6 constructs have been used extensively, individually or in some combination, as the dependent variable in research seeking to better understand the important antecedents or drivers of IS Success. Part 3 reviews this body of work. Part 4, ‘Benchmarking Information Systems’, drills deeper again, focusing more specifically on a measure of the IS that can be used as a ‘benchmark’3. This section consolidates and extends the work of the author and his colleagues4 to derive a robust, validated IS-Impact measurement model for benchmarking contemporary Information Systems (IS). Though IS-Impact, like ISS, has potential value in empirical, causal research, its design and validation has emphasized its role and value as a comparator; a measure that is simple, robust and generalizable and which yields results that are as far as possible comparable across time, across stakeholders, and across differing systems and systems contexts.

Evaluating the Java Virtual Machine as a Target for Languages Other Than Java

The portability and runtime safety of programs which are executed on the Java Virtual Machine (JVM) makes the JVM an attractive target for compilers of languages other than Java. Unfortunately, the JVM was designed with language Java in mind, and lacks many of the primitives required for a straighforward implementation of other languages. Here, we discuss how the JVM may be used to implement other object-oriented languages. As a practical example of the possibilities, we report on a comprehensive case study. The open source Gardens Point Component Pascal compiler compiles the entire Component Pascal language, a dialect of Oberon-2, to JVM bytecodes. This compiler achieves runtime efficiencies which are comparable to native-code implementations of procedural languages.

Implementing languages other than Java on the Java Virtual Machine

The portability and runtime safety of programs which are executed on the Java Virtual Machine (JVM) makes the JVM an attractive target for compilers of languages other than Java. Unfortunately, the JVM was designed with language Java in mind, and lacks many of the primitives required for a straight forward implementation of other languages. Here, we discuss how the JVM may be used to implement other object oriented languages. As a practical example of the possibilities, we report on a comprehensive case study. The open source Gardens Point Component Pascal compiler compiles the entire Component Pascal language, a dialect of Oberon 2, to JVM bytecodes. This compiler achieves runtime efficiencies which are comparable to native code implementations of procedural languages.

Statistical analysis and reduction of multiple access interference in MC-CDMA systems

Multicarrier code division multiple access (MC-CDMA) is a very promising candidate for the multiple access scheme in fourth generation wireless communi- cation systems. During asynchronous transmission, multiple access interference (MAI) is a major challenge for MC-CDMA systems and significantly affects their performance. The main objectives of this thesis are to analyze the MAI in asyn- chronous MC-CDMA, and to develop robust techniques to reduce the MAI effect. Focus is first on the statistical analysis of MAI in asynchronous MC-CDMA. A new statistical model of MAI is developed. In the new model, the derivation of MAI can be applied to different distributions of timing offset, and the MAI power is modelled as a Gamma distributed random variable. By applying the new statistical model of MAI, a new computer simulation model is proposed. This model is based on the modelling of a multiuser system as a single user system followed by an additive noise component representing the MAI, which enables the new simulation model to significantly reduce the computation load during computer simulations. MAI reduction using slow frequency hopping (SFH) technique is the topic of the second part of the thesis. Two subsystems are considered. The first sub- system involves subcarrier frequency hopping as a group, which is referred to as GSFH/MC-CDMA. In the second subsystem, the condition of group hopping is dropped, resulting in a more general system, namely individual subcarrier frequency hopping MC-CDMA (ISFH/MC-CDMA). This research found that with the introduction of SFH, both of GSFH/MC-CDMA and ISFH/MC-CDMA sys- tems generate less MAI power than the basic MC-CDMA system during asyn- chronous transmission. Because of this, both SFH systems are shown to outper- form MC-CDMA in terms of BER. This improvement, however, is at the expense of spectral widening. In the third part of this thesis, base station polarization diversity, as another MAI reduction technique, is introduced to asynchronous MC-CDMA. The com- bined system is referred to as Pol/MC-CDMA. In this part a new optimum com- bining technique namely maximal signal-to-MAI ratio combining (MSMAIRC) is proposed to combine the signals in two base station antennas. With the applica- tion of MSMAIRC and in the absents of additive white Gaussian noise (AWGN), the resulting signal-to-MAI ratio (SMAIR) is not only maximized but also in- dependent of cross polarization discrimination (XPD) and antenna angle. In the case when AWGN is present, the performance of MSMAIRC is still affected by the XPD and antenna angle, but to a much lesser degree than the traditional maximal ratio combining (MRC). Furthermore, this research found that the BER performance for Pol/MC-CDMA can be further improved by changing the angle between the two receiving antennas. Hence the optimum antenna angles for both MSMAIRC and MRC are derived and their effects on the BER performance are compared. With the derived optimum antenna angle, the Pol/MC-CDMA system is able to obtain the lowest BER for a given XPD.

A study into the permeability and compressibility of Australian bagasse pulp

This is an experimental study into the permeability and compressibility properties of bagasse pulp pads. Three experimental rigs were custom-built for this project. The experimental work is complemented by modelling work. Both the steady-state and dynamic behaviour of pulp pads are evaluated in the experimental and modelling components of this project. Bagasse, the fibrous residue that remains after sugar is extracted from sugarcane, is normally burnt in Australia to generate steam and electricity for the sugar factory. A study into bagasse pulp was motivated by the possibility of making highly value-added pulp products from bagasse for the financial benefit of sugarcane millers and growers. The bagasse pulp and paper industry is a multibillion dollar industry (1). Bagasse pulp could replace eucalypt pulp which is more widely used in the local production of paper products. An opportunity exists for replacing the large quantity of mainly generic paper products imported to Australia. This includes 949,000 tonnes of generic photocopier papers (2). The use of bagasse pulp for paper manufacture is the main application area of interest for this study. Bagasse contains a large quantity of short parenchyma cells called ‘pith’. Around 30% of the shortest fibres are removed from bagasse prior to pulping. Despite the ‘depithing’ operations in conventional bagasse pulp mills, a large amount of pith remains in the pulp. Amongst Australian paper producers there is a perception that the high quantity of short fibres in bagasse pulp leads to poor filtration behaviour at the wet-end of a paper machine. Bagasse pulp’s poor filtration behaviour reduces paper production rates and consequently revenue when compared to paper production using locally made eucalypt pulp. Pulp filtration can be characterised by two interacting factors; permeability and compressibility. Surprisingly, there has previously been very little rigorous investigation into neither bagasse pulp permeability nor compressibility. Only freeness testing of bagasse pulp has been published in the open literature. As a result, this study has focussed on a detailed investigation of the filtration properties of bagasse pulp pads. As part of this investigation, this study investigated three options for improving the permeability and compressibility properties of Australian bagasse pulp pads. Two options for further pre-treating depithed bagasse prior to pulping were considered. Firstly, bagasse was fractionated based on size. Two bagasse fractions were produced, ‘coarse’ and ‘medium’ bagasse fractions. Secondly, bagasse was collected after being processed on two types of juice extraction technology, i.e. from a sugar mill and from a sugar diffuser. Finally one method of post-treating the bagasse pulp was investigated. The effects of chemical additives, which are known to improve freeness, were also assessed for their effect on pulp pad permeability and compressibility. Pre-treated Australian bagasse pulp samples were compared with several benchmark pulp samples. A sample of commonly used kraft Eucalyptus globulus pulp was obtained. A sample of depithed Argentinean bagasse, which is used for commercial paper production, was also obtained. A sample of Australian bagasse which was depithed as per typical factory operations was also produced for benchmarking purposes. The steady-state pulp pad permeability and compressibility parameters were determined experimentally using two purpose-built experimental rigs. In reality, steady-state conditions do not exist on a paper machine. The permeability changes as the sheet compresses over time. Hence, a dynamic model was developed which uses the experimentally determined steady-state permeability and compressibility parameters as inputs. The filtration model was developed with a view to designing pulp processing equipment that is suitable specifically for bagasse pulp. The predicted results of the dynamic model were compared to experimental data. The effectiveness of a polymeric and microparticle chemical additives for improving the retention of short fibres and increasing the drainage rate of a bagasse pulp slurry was determined in a third purpose-built rig; a modified Dynamic Drainage Jar (DDJ). These chemical additives were then used in the making of a pulp pad, and their effect on the steady-state and dynamic permeability and compressibility of bagasse pulp pads was determined. The most important finding from this investigation was that Australian bagasse pulp was produced with higher permeability than eucalypt pulp, despite a higher overall content of short fibres. It is thought this research outcome could enable Australian paper producers to switch from eucalypt pulp to bagasse pulp without sacrificing paper machine productivity. It is thought that two factors contributed to the high permeability of the bagasse pulp pad. Firstly, thicker cell walls of the bagasse pulp fibres resulted in high fibre stiffness. Secondly, the bagasse pulp had a large proportion of fibres longer than 1.3 mm. These attributes helped to reinforce the pulp pad matrix. The steady-state permeability and compressibility parameters for the eucalypt pulp were consistent with those found by previous workers. It was also found that Australian pulp derived from the ‘coarse’ bagasse fraction had higher steady-state permeability than the ‘medium’ fraction. However, there was no difference between bagasse pulp originating from a diffuser or a mill. The bagasse pre-treatment options investigated in this study were not found to affect the steady-state compressibility parameters of a pulp pad. The dynamic filtration model was found to give predictions that were in good agreement with experimental data for pads made from samples of pretreated bagasse pulp, provided at least some pith was removed prior to pulping. Applying vacuum to a pulp slurry in the modified DDJ dramatically reduced the drainage time. At any level of vacuum, bagasse pulp benefitted from chemical additives as quantified by reduced drainage time and increased retention of short fibres. Using the modified DDJ, it was observed that under specific conditions, a benchmark depithed bagasse pulp drained more rapidly than the ‘coarse’ bagasse pulp. In steady-state permeability and compressibility experiments, the addition of chemical additives improved the pad permeability and compressibility of a benchmark bagasse pulp with a high quantity of short fibres. Importantly, this effect was not observed for the ‘coarse’ bagasse pulp. However, dynamic filtration experiments showed that there was also a small observable improvement in filtration for the ‘medium’ bagasse pulp. The mechanism of bagasse pulp pad consolidation appears to be by fibre realignment. Chemical additives assist to lubricate the consolidation process. This study was complemented by pulp physical and chemical property testing and a microscopy study. In addition to its high pulp pad permeability, ‘coarse’ bagasse pulp often (but not always) had superior physical properties than a benchmark depithed bagasse pulp.