Cold worked Cu-Fe-Cr alloys

The aim of this project was to investigate the properties of copper rich Cu-Fe-Cr alloys for the purpose of developing a new cost effective, high-strength, high-conductivity copper alloy. This paper reports on the influence of cold work. The age hardening response of the Cu-0.7%Cr-2.0%Fe alloy was minimal, but the resistance to softening was superior to that reported for any commercial high-strength, high-conductivity (HSHC) copper alloy with comparable mechanical and electrical properties. For example, an excess of 85% of the original hardness of the 40% cold worked alloy is retained after holding at 700 degreesC for 1 hour, whereas commercial HSHC Cu-Fe-P alloys have been reported to soften significantly after 1 hours exposure at less than 500 degreesC. The Cu-0.7Cr-2.0Fe alloy would therefore be expected to be more suitable for applications with a significant risk of exposure to elevated temperatures. Optical microscope examination of cold worked and aged microstructures confirmed the high resistance to recrystallization for Cu-0.7%Cr-2.0%Fe. The Zener-Smith drag term, predicting the pinning effect of second phase particles on dislocations in cold worked microstructures, was calculated using the precipitate characteristics obtained from TEM, WDS and resistivity measurements. The pinning effect of the precipitate dispersions in the peak-aged condition was determined to be essentially equivalent for the Cu-0.7%Cr-0.3%Fe and Cu-0.7%Cr-2.0%Fe alloys. A lower recrystallisation temperature in the Cu-0.7%Cr-0.3%Fe alloy was therefore attributed to faster coarsening kinetics of the secondary precipitates resulting from a higher Cr concentration in the precipitates at lower iron content. (C) 2001 Kluwer Academic Publishers.

Effects of moist chilling and solid matrix priming on germination of loblolly pine (Pinus taeda L.) seeds

Loblolly pine ( Pinus taeda L.) seeds from sources with a mild climate under maritime influence (North Carolina) required shorter moist chilling to achieve maximum germination vigor than seeds from sources with a harsher continental climate (Oklahoma). Solid matrix priming (SMP) for 6 d achieved as much as 60 d of moist chilling to improve rapidity, synchrony and completeness of germination for three of the four families studied. SMP after moist chilling increased the rapidity, synchrony and completeness of germination. The benefit of SMP was greatest for non-stratified seeds and the benefit decreased with length of moist chilling. In general, delaying planting for one week after SMP had minor effects on germination when seeds were kept in the SMP matrix at 4 degreesC. Delayed planting after SMP can increase germination rapidity and synchrony of seeds that have received long moist chilling and reduce the benefit of SMP in non-moist-chilled seeds.

Complete DNA sequence and gene organization of the mitochondrial genome of the liverfluke, Fasciola hepatica L. (Platyhelminthes; Trematoda)

The complete nucleotide sequence of the mitochondrial (mt) DNA molecule of the liverfluke, Fasciola hepatica (phylum Platyhelminthes, class Trematoda, family Fasciolidae), was determined, It comprises 14462 bp, contains 12 protein-encoding, 2 ribosomal and 22 transfer RNA genes, and is the second complete flatworm (and the first trematode) mitochondrial sequence to be described in detail. All of the genes are transcribed from the same strand. Of the genes typically found in mitochondrial genomes of eumetazoans, only atp8 is absent. The nad4L and nad4 genes overlap by 40 nt. Most intergenic sequences are very short. Two larger non-coding regions are present. The longer one (817 nt) is located between trnG and cox3 and consists of 8 identical tandem repeats of 85 nt, rich in G and C, followed by 1 imperfect repeat. The shorter non-coding region (187 nt) exhibits no special features and is separated from the longer region by trnG. The gene arrangement resembles that of some other trematodes including the eastern Asian Schistosoma species (and cyclophyllidean cestode species) but it is strikingly different from that of the African schistosomes, represented by Schistosoma mansoni. The genetic code is as inferred previously for flatworms. Transfer RNA genes range in length from 58 to 70 nt, their products producing characteristic 'clover leaf' structures, except for tRNA(S-VON) and tRNA(S-AGN) lacking the DHU arm.

Effect of propionyl-L-carnitine on exercise performance in peripheral arterial disease

Background: Supplementation with propionyl-L-carnitine (PLC) may be of use in improving the exercise capacity of people with peripheral arterial disease. Methods: After a 2-wk exercise familiarization phase, seven subjects displaying intermittent claudication were studied over a 12-wk period consisting of three 4-wk phases, baseline (B), supplementation (S), and placebo (P). PLC was supplemented at 2 g(.)d(-1), and subjects were blinded to the order of supplementation. Unilateral calf strength and endurance were assessed weekly. Walking performance was assessed at the end of each phase using an incremental protocol, during which respiratory gases were collected. Results: Although there was not a significant increase in maximal walking time (similar to 14%) in the whole group, walking time improved to a greater extent than the individual baseline coefficient of variation in four of the seven subjects. The changes in walking performance were correlated with changes in the respiratory exchange ratio both at steady state (r = 0.59) and maximal exercise (r = 0.79). Muscle strength increased significantly from 695 +/- 198 N to 812 +/- 249 N by the end of S. Changes in calf strength from B to S were modestly related to changes in walking performance (r = 0.56). No improvements in calf endurance were detected throughout the study. Conclusions: These preliminary data suggest that, in addition to walking performance, muscle strength can be increased in PAD patients after 4 wk of supplementation with propionyl-L-carnitine.

High-performance L-band series and parallel switches using low-cost p-i-n diodes

Low-cost UHF-band p-i-n diodes are used to develop high-performance L-band series and parallel switches. To stop the rectification of large RF, signals, the diodes are biased at a large reverse-bias voltage. Parasitic elements of the diodes are tuned out using LC circuits in biasing circuits without increasing the size of the switches. (C) 2002 John Wiley Sons, Inc.

Genetic differentiation between Australian and North American populations of the monarch butterfly Danaus plexippus (L.) (Lepidoptera : Nymphalidae): an exploration using allozyme electrophoresis

Allozyme analysis was used to address the question of the source of the Australian populations of the monarch butterfly Danaus plexippus (L.). The study had three major aims: (1) To compare the levels of diversity of Australian and Hawaiian populations with potential source populations. (2) To determine whether eastern and western North American populations were sufficiently divergent for the Australian populations to be aligned to a source population. (3) To compare the differentiation among regions in Australia and North America to test the prediction of greater genetic structure in Australia, as a consequence of reduced migratory behaviour. The reverse was found, with F-ST values an order of magnitude lower in Australia than in North America. Predictably, Australian and Hawaiian populations had lower allelic diversity, but unexpected higher heterozygosity values than North American populations. It was not possible to assign the Australian populations to a definitive source, although the high levels of similarity of Australian populations to each other suggest a single colonization event. The possibility that the Australian populations have not been here long enough to reach equilibrium is discussed. (C) 2002 The Linnean Society of London, Biological Journal of the Linnean Society, 2002, 75, 437-452.

Urine D-arabinitol/L-arabinitol ratio in diagnosing Candida infection in patients with haematological malignancy and HIV infection

Adult patients with hematologic malignancies along with HIV infected patients were prospectively studied to determine the performance of urine D-arabinitol/L-arabinitol (DA/LA) ratio in diagnosing invasive candidiasis. Ten evaluable febrile neutropenic patients had proven invasive candidiasis and elevated DA/LA ratios were found in 5. Invasive candidiasis with normal DA/LA ratios was most frequently due to Candida krusei infection. This Candida species is a non-producer of arabinitol. Only 4 of 81 febrile neutropenic patients given either antifungal prophylaxis or empiric antifungal treatment had elevated DA/LA ratios. Only 1 of 15 HIV positive patients with either oropharyngeal or esophageal candidiasis had elevated DA/LA ratios. Widespread use of fluconazole prophylaxis in bone marrow transplantation patients at the study hospital has led to an increased prevalence of C. krusei infection. This is the likely reason for the low sensitivity of the test in proven and suspected invasive Candida infections reported here. (C) 2002 Elsevier Science Inc. All rights reserved.

Characterization of a chemsensory protein (ASP3c) from honeybee (Apis mellifera L.) as a brood pheromone carrier

Chemosensory proteins (CSPs) are ubiquitous soluble small proteins isolated from sensory organs of a wide range of insect species, which are believed to be involved in chemical communication. We report the cloning of a honeybee CSP gene called ASP3c, as well as the structural and functional characterization of the encoded protein. The protein was heterologously secreted by the yeast Pichia pastoris using the native signal peptide. ASP3c disulfide bonds were assigned after trypsinolysis followed by chromatography and mass spectrometry combined with microsequencing. The pairing (Cys(I)-Cys(II), Cys(III)-Cys(IV)) was found to be identical to that of Schistocerca gregaria CSPs, suggesting that this pattern occurs commonly throughout the insect CSPs. CD measurements revealed that ASP3c mainly consists of alpha-helices, like other insect CSPs. Gel filtration analysis showed that ASP3c is monomeric at neutral pH. Using ASA, a fluorescent fatty acid anthroyloxy analogue as a probe, ASP3c was shown to bind specifically to large fatty acids and ester derivatives, which are brood pheromone components, in the micromolar range. It was unable to bind tested general odorants and other tested pheromones (sexual and nonsexual). This is the first report on a natural pheromonal ligand bound by a recombinant CSP with a measured affinity constant.

Modelling of Lamb waves in composite laminated plates excited by interdigital transducers

The technique of permanently attaching interdigital transducers (IDT) to either flat or curved structural surfaces to excite single Lamb wave mode has demonstrated great potential for quantitative non-destructive evaluation and smart materials design, In this paper, the acoustic wave field in a composite laminated plate excited by an IDT is investigated. On the basis of discrete layer theory and a multiple integral transform method, an analytical-numerical approach is developed to evaluate the surface velocity response of the plate due to the IDTs excitation. In this approach, the frequency spectrum and wave number spectrum of the output of IDT are obtained directly. The corresponding time domain results are calculated by applying a standard inverse fast Fourier transformation technique. Numerical examples are presented to validate the developed method and show the ability of mode selection and isolation. A new effective way of transfer function estimation and interpretation is presented by considering the input wave number spectrum in addition to the commonly used input frequency spectrum. The new approach enables the simple physical evaluation of the influences of IDT geometrical features such as electrode finger widths and overall dimension and excitation signal properties on the input-output characteristics of IDT. Finally, considering the convenience of Mindlin plate wave theory in numerical computations as well as theoretical analysis, the validity is examined of using this approximate theory to design IDT for the excitation of the first and second anti-symmetric Lamb modes. (C) 2002 Elsevier Science Ltd. All rights reserved.

Shear stress and sediment transport calculations for sheet flow under waves

A simple method is provided for calculating transport rates of not too fine (d(50) greater than or equal to 0.20 mm) sand under sheet flow conditions. The method consists of a Meyer-Peter-type transport formula operating on a time-varying Shields parameter, which accounts for both acceleration-asymmetry and boundary layer streaming. While velocity moment formulae, e.g.., = Constant x calibrated against U-tube measurements, fail spectacularly under some real waves (Ribberink, J.S., Dohmen-Janssen, C.M., Hanes, D.M., McLean, S.R., Vincent, C., 2000. Near-bed sand transport mechanisms under waves. Proc. 27th Int. Conf. Coastal Engineering, Sydney, ASCE, New York, pp. 3263-3276, Fig. 12), the new method predicts the real wave observations equally well. The reason that the velocity moment formulae fail under these waves is partly the presence of boundary layer streaming and partly the saw-tooth asymmetry, i.e., the front of the waves being steeper than the back. Waves with saw-tooth asymmetry may generate a net landward sediment transport even if = 0, because of the more abrupt acceleration under the steep front. More abrupt accelerations are associated with thinner boundary layers and greater pressure gradients for a given velocity magnitude. The two real wave effects are incorporated in a model of the form Q(s)(t) = Q(s)[theta(t)] rather than Q(S)(t) = Q(S)[u(infinity)(t)], i.e., by expressing the transport rate in terms of an instantaneous Shields parameter rather than in terms of the free stream velocity, and accounting for both streaming and accelerations in the 0(t) calculations. The instantaneous friction velocities u(*)(t) and subsequently theta(t) are calculated as follows. Firstly, a linear filter incorporating the grain roughness friction factor f(2.5) and a phase angle phi(tau) is applied to u(infinity)(t). This delivers u(*)(t) which is used to calculate an instantaneous grain roughness Shields parameter theta(2.5)(t). Secondly, a constant bed shear stress is added which corresponds to the streaming related bed shear stress -rho ($) over bar((u) over tilde(w) over tilde)(infinity) . The method can be applied to any u(infinity)(t) time series, but further experimental validation is recommended before application to conditions that differ strongly from the ones considered below. The method is not recommended for rippled beds or for sheet flow with typical prototype wave periods and d(50) < 0.20 turn. In such scenarios, time lags related to vertical sediment movement become important, and these are not considered by the present model. (C) 2002 Elsevier Science B.V. All rights reserved.

Vertical fluxes of sediment in oscillatory sheet flow

Time series of vertical sediment fluxes are derived from concentration time series in sheet flow under waves. While the concentrations C(z,t) vary very little with time for \z\ < 10d(50), the measured vertical sediment fluxes Q(zs)(z,t) vary strongly with time in this vertical band and their time variation follows, to some extent, the variation of the grain roughness Shields parameter 02,5(t). Thus, sediment distribution models based on the pickup function boundary condition are in some qualitative agreement with the measurements. However, the pickup function models are only able to model the upward bursts of sediment during the accelerating phases of the flow. They are, so far, unable to model the following strong downward sediment fluxes, which are observed during the periods of flow deceleration. Classical pickup functions, which essentially depend on the Shields parameter, are also incapable of modelling the secondary entrainment fluxes, which sometimes occur at free stream velocity reversal. The measured vertical fluxes indicate that the effective sediment settling velocity in the high [(0.3 < C(z,t) < 0.4] concentration area is typically only a few percent of the clear water settling velocity, while the measurements of Richardson and Jeronimo [Chem. Eng. Sci. 34 (1979) 1419], from a different physical setting, lead to estimates of the order 20%. The data does not support gradient diffusion as a model for sediment entrainment from the bed. That is, detailed modelling of the observed near-bed fluxes would require diffusivities that go negative during periods of flow deceleration. An observed general trend for concentration variability to increase with elevation close to the bed is also irreconcilable with diffusion models driven by a bottom boundary condition. (C) 2002 Published by Elsevier Science B.V.

Partial automation of database processing of simulation outputs from L-systems models of plant morphogenesis

Models of plant architecture allow us to explore how genotype environment interactions effect the development of plant phenotypes. Such models generate masses of data organised in complex hierarchies. This paper presents a generic system for creating and automatically populating a relational database from data generated by the widely used L-system approach to modelling plant morphogenesis. Techniques from compiler technology are applied to generate attributes (new fields) in the database, to simplify query development for the recursively-structured branching relationship. Use of biological terminology in an interactive query builder contributes towards making the system biologist-friendly. (C) 2002 Elsevier Science Ireland Ltd. All rights reserved.

Single mode Lamb waves in composite laminated plates generated by piezoelectric transducers

The technique of permanently attaching piezoelectric transducers to structural surfaces has demonstrated great potential for quantitative non-destructive evaluation and smart materials design. For thin structural members such as composite laminated plates, it has been well recognized that guided Lamb wave techniques can provide a very sensitive and effective means for large area interrogation. However, since in these applications multiple wave modes are generally generated and the individual modes are usually dispersive, the received signals are very complex and difficult to interpret. An attractive way to deal with this problem has recently been introduced by applying piezoceramic transducer arrays or interdigital transducer (IDT) technologies. In this paper, the acoustic wave field in composite laminated plates excited by piezoceramic transducer arrays or IDT is investigated. Based on dynamic piezoelectricity theory, a discrete layer theory and a multiple integral transform method, an analytical-numerical approach is developed to evaluate the input impedance characteristics of the transducer and the surface velocity response of the plate. The method enables the quantitative evaluation of the influence of the electrical characteristics of the excitation circuit, the geometric and piezoelectric properties of the transducer array, and the mechanical and geometrical features of the laminate. Numerical results are presented to validate the developed method and show the ability of single wave mode selection and isolation. The results show that the interaction between individual elements of the piezoelectric array has a significant influence on the performance of the IDT, and these effects can not be neglected even in the case of low frequency excitation. It is also demonstrated that adding backing materials to the transducer elements can be used to improve the excitability of specific wave modes. (C) 2002 Elsevier Science Ltd. All rights reserved.