Hybrid FIB milling strategy for the fabrication of plasmonic nanostructures on semiconductor substrates

The optical properties of plasmonic semiconductor devices fabricated by focused ion beam (FIB) milling deteriorate because of the amorphisation of the semiconductor substrate. This study explores the effects of combining traditional 30 kV FIB milling with 5 kV FIB patterning to minimise the semiconductor damage and at the same time maintain high spatial resolution. The use of reduced acceleration voltages is shown to reduce the damage from higher energy ions on the example of fabrication of plasmonic crystals on semiconductor substrates leading to 7-fold increase in transmission. This effect is important for focused-ion beam fabrication of plasmonic structures integrated with photodetectors, light-emitting diodes and semiconductor lasers.

Efficient modelling and optimisation of hybrid multilayered plates subject to ballistic impact

Among the key challenges present in the modelling and optimisation of composite structures against impact is the computational expense involved in setting up accurate simulations of the impact event and then performing the iterations required to optimise the designs. It is of more interest to find good designs given the limitations of the resources and time available rather than the best possible design. In this paper, low cost but sufficiently accurate finite element (FE) models were generated in LS Dyna for several experimentally characterised materials by semi-automating the modelling process and using existing material models. These models were then used by an optimisation algorithm to generate new hybrid offspring, leading to minimum weight and/or cost designs from a selection of isotropic metals, polymers and orthotropic fibre-reinforced laminates that countered a specified impact threat. Experimental validation of the optimal designs thus identified was then successfully carried out using a single stage gas gun. With sufficient computational hardware, the techniques developed in this pilot study can further utilise fine meshes, equations of state and sophisticated material models, so that optimal hybrid systems can be identified from a wide range of materials, designs and threats.

Intralaminar toughness characterisation of unbalanced hybrid plain weave laminates

A numerical and experimental investigation on the mode-I intralaminar toughness of a hybrid plain weave composite laminate manufactured using resin infusion under flexible tooling (RIFT) process is presented in this paper. The pre-cracked geometries consisted of overheight compact tension (OCT), double edge notch (DEN) and centrally cracked four-point-bending (4PBT) test specimens. The position as well as the strain field ahead of the crack tip during the loading stage was determined using a digital speckle photogrammetry system. The limitation on the applicability of the standard data reduction schemes for the determination of intralaminar toughness of composite materials is presented and discussed. A methodology based on the numerical evaluation of the strain energy release rate using the J-integral method is proposed to derive new geometric correction functions for the determination of the stress intensity factor for composites. The method accounts for material anisotropy and finite specimen dimension effects regardless of the geometry. The approach has been validated for alternative non-standard specimen geometries. A comparison between different methods currently available for computing the intralaminar fracture toughness in composite laminates is presented and a good agreement between numerical and experimental results using the proposed methodology was obtained. 

Evaluation of a substructured soft Real-time Hybrid Test for performing Seismic analysis of complex structural systems

The hybrid test method is a relatively recently developed dynamic testing technique that uses numerical modelling combined with simultaneous physical testing. The concept of substructuring allows the critical or highly nonlinear part of the structure that is difficult to numerically model with accuracy to be physically tested whilst the remainder of the structure, that has a more predictable response, is numerically modelled. In this paper, a substructured soft-real time hybrid test is evaluated as an accurate means of performing seismic tests of complex structures. The structure analysed is a three-storey, two-by-one bay concentrically braced frame (CBF) steel structure subjected to seismic excitation. A ground storey braced frame substructure whose response is critical to the overall response of the structure is tested, whilst the remainder of the structure is numerically modelled. OpenSees is used for numerical modelling and OpenFresco is used for the communication between the test equipment and numerical model. A novel approach using OpenFresco to define the complex numerical substructure of an X-braced frame within a hybrid test is also presented. The results of the hybrid tests are compared to purely numerical models using OpenSees and a simulated test using a combination of OpenSees and OpenFresco. The comparative results indicate that the test method provides an accurate and cost effective procedure for performing
full scale seismic tests of complex structural systems.

Hybrid Polyoxovanadates: Anion-Influenced Formation of Nanoscopic Cages and Supramolecular Assemblies of Asymmetric Clusters

Organoarsonate-functionalized polyoxovanadates form upon the reduction of vanadates(V) in aqueous systems, whereby the underlying condensation reactions are influenced by the nature of the employed acid. In the presence of Cl− ions that derive from hydrochloric acid, a tetradecanuclear cage [VIV14O16(OH)8(O3AsC6H4-4-NH2)10]4– is obtained. When nitric acid is used, a condensed, decanuclear complex [V10O18(O3AsC6H4-4-NH2)7(DMF)2]5– forms. The latter organizes into a hexagonal packing arrangement in the solid state.

Hybrid Organic–Inorganic Polyoxometalates: Functionalization of VIV/ VV Nanosized Clusters to Produce Molecular Capsules

Functionalization of polyoxovanadate clusters using phosphonate and arsonate ligands results in molecular capsules (see structure; green V, purple P, red O, black C). Through the use of extended homologous ligands, these hybrid organic-inorganic capsules can be successively elongated into tubular molecules.

Composite materials based on silk proteins

A number of animals have evolved to produce silk-based composite materials for a variety of task-specific applications. The review initially focuses on the composite structure of silk fibers produced naturally by silkworms and spiders, followed by the preparation and applications of man-made composite materials (including fibers, films, foams, gels and particulates) incorporating silk proteins in combination with other polymers (both natural and synthetic) and/or inorganic particles. 

Atmospheric Pressure DC Plasma Processing of TIO2/PEDOT:PSS Nanocomposites

In this work we demonstrate the synthesis of a TiO2/PEDOT:PSS nanocomposite material in aqueous solution through atmospheric pressure direct current (DC) plasma processing at room temperature. The dispersion of the TiO2 nanoparticles is enhanced after microplasma processing, and TiO2/polymer hybrid nanoparticles with a distinct core shell structure have been obtained. We have observed increased TiO2/PEDOT:PSS nanocomposite electrical conductivity due to microplasma processing. The improvement in nanocomposite properties is due to the enhanced dispersion and stability in liquid polymer of microplasma treated TiO2 nanoparticles. Both plasma induced surface charge and nanoparticle surface termination with specific plasma chemical species are thought to provide an enhanced barrier to nanoparticle agglomeration and promote nanoparticle-polymer bonding, which is expected to have a significant benefit in materials processing with inorganic nanoparticles for wide range of applications.

Laser-fabricated PET-Ti Hybrid Joints for Medical Device Applications

Currently, micro-joining of plastic parts to metal parts in medical devices is achieved by using medical adhesives, For example, pacemakers, defibrillators and neurological stimulators are designed using silicone adhesive to seal the joint between the polyurethane connector module and the titanium can [1]. Nevertheless, the use of adhesive is problematic because it requires a long time to cure and has high tendency to produce leachable products which might be harmful to the human body. An alternative for directly joining plastics to metal without adhesive is therefore required. Laser transmission joining (LTJ) is growing in importance, and has the potential to gain the niche in micro-fabrication of plastics-metal hybrid joints for medical device applications. The possibility of directly joining plastics to metal by LTJ technique have been demonstrated by a number of studies in recent literature [2]. The widely-accepted understanding of LTJ between plastics and metal is that generation and rapid expansion of micro-bubbles at the plastics-metal interface exert high local pressure to press the melted plastics towards the metal surface features during the laser processing [2]. This subsequently creates the plastics-metal hybrid joint by the mechanisms of mechanical interlocking as well as chemical and physical bonds between the plastics and metal surfaces. Although the micro-bubbles can help promote the mechanical interlocking effect to increase the joint strength, the creation of bubble is a random and complex process depending on the complicated interactions between the laser intensity, thermal degradation properties of plastics, surface temperature and topographical features of metal. In an ideal situation, it is desirable to create the hybrid plastics-metal joint without bubbles. However, the mechanical performance of the hybrid plastics-metal joint without bubbles is still unknown, and systematic comparison between the hybrid joints with and without bubbles is lacking in literature. This becomes the objective of this study. In this work, the laser process parameters were carefully chosen from a preliminary study, such that different hybrid joints: with and without bubbles can be produced and compared. Biocompatible PET and commercially pure Ti were selected as materials for laser joining.

Interacções intermoleculares fracas em materiais funcionais avançados: um estudo espectroscópico e computacional

A utilização combinada de espectroscopia vibracional e de cálculos envolvendo a teoria do funcional de densidade (DFT) possibilita o estudo de ligações de hidrogénio em fase condensada, assim como a análise da estrutura molecular dos sistemas em estudo. Por um lado, a espectroscopia vibracional permite a detecção de associações moleculares, enquanto os métodos computacionais auxiliam na obtenção de informação referente aos mecanismos de associação, nomeadamente no que diz respeito à possível estrutura de dímeros e compostos de inclusão em ciclodextrinas e às energias de interacção e de inclusão. O estudo que originou a presente dissertação pretende contribuir para o reforço da aplicação de estudos espectroscópicos e computacionais na elucidação de diversos fenómenos químicos, com especial destaque para o papel desempenhado por interacções intermoleculares fracas na estrutura e propriedades de materiais moleculares. No âmbito desta tese foram investigados os seguintes tópicos: polimorfismo e pseudopolimorfismo em sólidos farmacêuticos, transições de fase em misturas binárias de ácidos gordos, inclusão em ciclodextrinas, interacção de compostos farmacêuticos com superfícies metálicas e formação de agregados de água em materiais híbridos orgânicos-inorgânicos. Os sistemas foram analisados utilizando a espectroscopia vibracional – particularmente a espectroscopia de difusão de Raman – como técnica fundamental. Para uma melhor caracterização de processos envolvendo transições de fase, foram efectuados estudos com variação de temperatura, variação de humidade relativa e substituição isotópica. O estudo da interacção com superfícies metálicas foi realizado por espectroscopia de Raman intensificada à superfície. Dada a complexidade dos sistemas em estudo, a informação obtida por espectroscopia vibracional foi complementada por resultados de cálculos mecânico-quânticos. Em particular, os cálculos DFT foram utilizados para a optimização de geometrias e previsão de frequências vibracionais de moléculas e associações moleculares, permitindo assim a análise e interpretação de espectros vibracionais e a caracterização da estrutura de materiais.