Extrusion and characterization of functionalized cellulose whiskers reinforced polyethylene nanocomposites

The surface of ramie cellulose whiskers has been chemically modified by grafting organic acid chlorides presenting different lengths of the aliphatic chain by an esterification reaction. The occurrence of the chemical modification was evaluated by FTIR and X-ray photoelectron spectroscopies, elemental analysis and contact angle measurements. The crystallinity of the particles was not altered by the chain grafting, but it was shown that covalently grafted chains were able to crystallize at the cellulose surface when using C18. Both unmodified and functionalized nanoparticles were extruded with low density polyethylene to prepare nanocomposite materials. The homogeneity of the ensuing nanocomposites was found to increase with the length of the grafted chains. The thermomechanical properties of processed nanocomposites were studied by differential scanning calorimetry (DSC), dynamical mechanical analysis (DMA) and tensile tests. A significant improvement in terms of elongation at break was observed when sufficiently long chains were grafted on the surface of the nanoparticles. It was ascribed to improved dispersion of the nanoparticles within the LDPE matrix. (C) 2009 Elsevier Ltd. All rights reserved.

Development of a new stir bar sorptive extraction coating and its application for the determination of six pesticides in sugarcane juice

In this article, a novel polydimethylsiloxane/activated carbon (PDMS-ACB) material is proposed as a new polymeric phase for stir bar sorptive extraction (SBSE). The PDMS-ACB stir bar, assembled using a simple Teflon (R)/glass capillary mold, demonstrated remarkable stability and resistance to organic solvents for more than 150 extractions. The SBSE bar has a diameter of 2.36 mm and a length of 2.2 cm and is prepared to contain 92 mu L of polymer coating. This new PDMS-ACB bar was evaluated for its ability to determine the quantity of pesticides in sugarcane juice samples by performing liquid desorption (LD) in 200 mu L of ethyl acetate and analyzing the solvent through gas chromatography coupled with mass spectrometry (GC-MS). A fractional factorial design was used to evaluate the main parameters involved in the extraction procedure. Then, a central composite design with a star configuration was used to optimize the significant extraction parameters. The method used demonstrated a limit of quantification (LOQ) of 0.5-40 mu g/L, depending on the analyte detected; the amount of recovery varied from 0.18 to 49.50%, and the intraday precision ranged from 0.072 to 8.40%. The method was used in the analysis of real sugarcane juice samples commercially available in local markets.

TLC Separation and Identification of the Essential Oil Constituents from Aloysia gratissima

The present work had as objective the isolation of the five compounds by thin-layer Chromatography (TLC) from the essential oil of the Aloysia gratissima. For this, a number of systems of eluents were used for its separation, indicating that through the system acetone/hexane in proportions (v/v) 1:30 it was possible to isolate guaiol, elemol, pinocanphone (trans-3-pinanone), cis-pinocarvyl, and acorenone. The isolation of the compound acorenone from the other compounds was possible with the mixture of solvents hexane/dichloromethane in proportions (v/v) (1:1,3).

Comparação entre os intumescimentos de borracha natural e polibutadieno com alto teor 1,4-cis em solventes (n-octano, ciclo-hexano e esqualeno) e em soluções poliméricas

Amostras de borracha natural foram reticuladas por meio de radiação gama (doses de 2, 4, 6 e 8 MRad) e intumescidas: a) em n-octano, ciclo-hexano e esqualeno; b) em polibutadieno líquido (Mn=1830 g/mol; alto teor 1,4- cis) a 45°C; C) em solução de polibutadieno de baixo peso molecular (M,= 1830 g/mol; alto teor 1,4-cis) em n-octano e ciclo-hexano; d) em solução de polibutadieno de alto peso molecular (Mn= 175.000 g/rnol; alto teor 1,4-cis) emn-octano e ciclo-hexano ; e) em solução de borracha natural (Mn=779.000 g/mol) em ciclo- hexano, a 25°C. Amostras de polibutadieno (alto teor 1,4-cis) foram reticuladas por meio de radiação gama (doses de 1,s; 18 e 25 MRad) e intumescidas: a) em n-octano, ciclo-hexano e esquaieno. Salvo quando mencionado em contrário, as amostras de borracha natural e de polibutadieno foram intumescidas nas temperaturas de 25, 35 e 45°C. A partir dos ensaios de intumescirnento acima mencionados, foram determinadas as solubilidades de borracha natural e de polibutadieno em n-octano, ciclo-hexano e esqualeno através dos parâmetros de Flory-Huggins, calculados com o emprego da equação de Flory-Rehner. Verificou-se a influência da temperatura e da concentração de polimero no gel sobre o valor do parâmetro de Flory-Huggins. Também através desse parâmetro procurou-se determinar a compatibilidade entre borracha natural e polibutadieno. Foi demonstrado que cadeias lineares de baixo peso molecular de polibutadieno conseguem penetrar em amostras reticuladas de borracha natural, quando o peso molecular das cadeias lineares for bem inferior ao do arco de rede Mc das amostras reticuladas. Cadeias lineares de polibutadieno e de borracha natural com peso molecular superior ao do arco de rede da borracha natural reticulada, entretanto, não conseguem penetrar no retículo. Quranto mais alta a concentração da solução externa em moléculas de alto peso molecular, tanto menor é o grau de intumescimento da amostra reticulada.

Solubilizacao e interacao de pigmentos com solventes organicos e agentes tenso-ativos

A Mg e Mn-Ftalocianina (Mg e Mn-Pc) foram solubilizados à 25°C em dimetilsulfóxido (DMSO); N, N-dimetilacetamida (DMA); N,N-dimetilformamida (DMF); N-metil-formamida, formamida, piridina, o-diclorobenzeno, monoclorobenzeno, tolueno, metanol, etanol, propanol-1, propanol-2, butanol-1 e octanol-1. Alguns valores representativos obtidos para o logarítimo da absortividade molar (E) da Mn-Pc, são os seguintes: o-diclorobenzeno (E = 4,94); DMSO (E = 4,39); octanol-1 (E = 3,90). Valores correspondentes para Mg-Pc são: o-diclarobenzeno (E = 4,93); DMSO (E = 5,22) e Octanol-1 ( E = 5,06). Em função de interação com solventes, pode-se classificar a Mg-Pc como um indicador básico e a Mn-Pc como indicador ácido. Os pigmentos Mg e Mn-Pc foram também solubillzados em soluções aquosas contendo vários surfatantes à 25°C. A Mg-Pc apresentou solubilidade significativa em água contendo brometo de cetiltrimetilamônio (CTAB), Brij-35, cloreto de cetilpiridinio (CPC1), brometo de cetilpiridínio (CPBr,) Triton X-100, cloreto de metildodecilbenziltrimetilamônio, brometo de cetildimetiletilamõnio e brometo de laurilisoquinolínio. A Mn-Pc foi solúvel em soluções aquosas de Brij-35 e Triton X-100. Em função de sua interação com surfatantes a Mg-Pc é classificada como corante catiônico e a Mn-Pc como corante aniônico. O corante comercial quinóide Oil Blue A [1,4-di(isopropilarnina)-antraquinona - 9,10 foi solubilizado à 25°C em DMF, DMSO, DMA, monoclorobenzeno, benzeno, tolueno, piridina, metanol, etanol, propanol-1, propanol-2, butanol-1 e octanol-1. Foi também solubilizado em soluções aquosas de surfatantes, tais como sódio lauril-sulfato (NaLS), cloreto de cetiltrimetilamônio (CTAB), brometo de cetildimetiletilamônio, Triton X-100, cloreto de cetilpiridínio (CPCl), Brij-35, cloreto de rnetildodecilbenziltrimetilamônio e brometo de laurilisoquinolínio. Em função de suas interações com os solventes o corante é um indicador ácido-básico pouco sensível e em função de sua interação com surfatantes é um corante catiônico. 0s resultados experimentais apresentam importância teórica e prática considerando sistemas que envolvem armazenamento e transferência de energia, compostos porfirínicos, fotossíntese, fotocondutores, coletores solares, semi-condutores e processos de embelezamento e proteção de superficies de vários materiais.

Caracterização química da erva mate (Ilex paraguariensis) : aplicação de diferentes processos de extração e influência das condições de plantio sobre a composição química

O objetivo deste trabalho foi estudar a composição química das folhas de erva-mate, sob diferentes condições agronômicas e técnicas de extração. Os métodos de extração usados foram maceração, ultra-som, extração com líquido pressurizado e extração com fluído supercrítico. Foram investigadas as variáveis que podem influenciar no processo de extração, tais como temperatura, pressão, polaridade do solvente, tempo de extração, massa de amostra, entre outras. A identificação dos compostos foi realizada por cromatografia gasosa acoplada à espectrometria de massas. Todos os métodos de extração utilizados mostraram-se eficientes para a obtenção dos extratos, com as diferenças sendo mais quantitativas do que qualitativas . Entre os métodos de extração que utilizam solventes orgânicos, a extração com líquido pressurizado mostrou-se mais eficiente, produzindo maior rendimento em massa de extrato e maior concentração de alguns dos compostos de interesse, com as vantagens de redução de solvente e tempo de extração. A composição química da erva-mate é influenciada pelas condições agronômicas de plantio, bem como pelas condições de extração de suas folhas. A melhor condição agronômica avaliada, ou seja, aquela que produziu maior quantidade de extrato, foi o cultivo das plantas a pleno sol, adubadas com nitrogênio e com idade de poda de 18 meses. A variável mais importante das técnicas de extração utilizadas foi a polaridade do solvente. Solventes de maior polaridade produziram maior rendimento em extrato. A análise cromatográfica dos extratos obtidos permitiu identificar cerca de 50 compostos qualitativamente e 6 quantitativamente, destacando-se a cafeína, fitol, ácido palmítico, ácido esteárico, esqualeno e vitamina E.

Desenvolvimento de elastômeros termoplásticos a partir de SBR epoxidada e polipropileno

Os elastômeros termoplásticos vulcanizados (TPVs) na sua maioria constituídos por borrachas apolares (EPDM, NR) e poliolefinas (PP, PE), apresentam a vantagem de serem processáveis como termoplásticos e serem facilmente reciclados. No entanto, apresentam desvantagens no que se refere à sua baixa resistência a óleos, combustíveis e graxas em relação à borracha termofixa. Este trabalho, teve como objetivo estudar a obtenção de TPVs com propriedades mecânicas adequadas e resistência a óleos e solventes orgânicos, a partir da borracha comercial SBR 1502 parcialmente epoxidada. Esta, por ter a estrutura química de sua cadeia principal modificada pela introdução de grupos epóxidos, deve apresentar melhor resistência a óleos e solventes. Os TPVs foram obtidos em misturador fechado acoplado a um reômetro Haake, na temperatura de 1800C e velocidade de rotor de 75 rpm, vulcanizados dinamicamente com o sistema Bismaleimida/peróxido de dicumila. Foram caracterizados quanto às suas propriedades mecânicas por medidas tensão-deformação, medidas mecânicas dinâmicas, inchamento em ciclohexano, THF e óleo IRM 903, dureza. A morfologia foi determinada por microscopia eletrônica de varredura, MEV. Foram analisados os fatores que influenciam as propriedades dos TPVs, tais como composição (relação PP/SBR), teor de BMI, grau de epoxidação da borracha, uso de agente compatibilizante. O TPV na composição PP/SBR 40/60, esta epoxidada em 40 mol % e contendo o agente compatibilizante Vestenamer adicionado na forma de blenda (borracha/agente compatibilizante) apresentou a melhor resposta em termos de tensão-deformação na ruptura. Os TPVs com a SBR epoxidada em 70% apresentaram melhor resistência a óleo e solventes. Os fatores, potencialmente, capazes de influenciar a dureza dos TPVs também foram avaliados. Neste particular, verificou-se que o tipo de poliolefina, bem como o uso de plastificante são os fatores que mais influenciam a dureza dos TPVs.

Adolescência e infecção pelo HIV : situações de risco e proteção, autoconceito e sintomatologia psiquiátrica

Esta dissertação tem como objetivo identificar, através de um estudo transversal, associações entre as características demográficas, comportamentos de risco sexual e por drogas, sintomatologia psiquiátrica e autoconceito em uma amostra de adolescentes, comparando-os pela soropositividade HIV. Foram entrevistados 388 adolescentes entre 13 e 20 anos que procuraram espontaneamente o Centro de Triagem e Avaliação (CTA) Paulo César Bonfim para realizar o teste anti-HIV. Foram utilizados os questionários CRA (Comportamentos de Risco para AIDS), SCL-90-R (The Symptom Check-List-90-R) e EFA (Escala Fatorial de Autoconceito). A média da idade foi de 17,7 anos (±2,0). A maioria da amostra era do sexo feminino, solteiro ou sem companheiro/a fixo/a, sem trabalho, com baixas escolaridade e renda familiar. Em relação ao teste sorológico, 73% estavam realizandoo pela primeira vez, e a soropositividade geral da amostra foi de 6,2%. A escolaridade foi significativamente mais baixa em soropositivos (OR= 7,8) e não houve diferença estatística entre os grupos nas demais variáveis demográficas. Houve associação direta entre soropositividade e precocidade de início da vida sexual (OR= 3,6), história de gravidez (OR=4,7), prática de aborto prévio (OR= 5,9) e relação sexual com parceiro sem preservativo (OR=3,2). Do total da amostra, 8% dos adolescentes recebeu dinheiro em troca de relação sexual, e isto foi associado à soropositividade (OR=4,5). O mesmo ocorreu nos 13,2% que tiveram relação sexual com paceiro/a possivelmente soropositivo (OR=8,3). Apenas 18,9% da amostra afirmaram usar preservativos nos 6 meses prévios à coleta e 81,4% da amostra não haviam usado preservativo nas relações sexuais ao longo da vida. A prevalência geral de uso de drogas no mês anterior à coleta foi alta, com relato freqüente de uso de múltiplas drogas, sendo as mais freqüentes o álcool (71,6 %), maconha (24,7%), cocaína intranasal (12,4%) e solventes (9,3 %). A soropositividade foi mais alta nos usuários recentes de maconha (OR= 2,8), estimulantes (OR=2,9) e solventes (OR= 7,5). A freqüência a local específico para uso de drogas ocorreu em 22,5% do total da amostra e foi estatisticamente maior nos soropositivos (OR=2,6). Os adolescentes soropositivos apresentaram siginficativamente mais sintomatologia psiquiátrica em todas as dimensões avaliadas. Não houve diferença nas dimensões de autoconceito. O Tamanho de Efeito Padronizado foi maior nas variáveis da sintomatologia psiquiátrica do que nas do autoconceito. Os resultados indicam que os adolescentes estudados ainda não possuem cuidados preventivos suficientes para diminuir o contágio pelo vírus da AIDS. São indivíduos sob risco constante por apresentarem maior freqüência de exposição ao HIV associada à baixa escolaridade, comportamento sexual, uso de drogas e sintomatologia psiquiátrica. A falta de diferenças no autoconceito dos adolescentes soropositivos e soronegativos pode estar associada ao senso de invulnerabilidade próprio da faixa etária. Os achados apontam para a necessidade de programas específicos de prevenção para adolescentes. Medidas de intervenção futuras deverão levar em conta a interação de fatores individuais, ambientais, comportamentais e psicológicos, com o objetivo de implementar mudanças efetivas no comportamento de risco para que se detenha o avanço da epidemia nessa faixa etária.

Comparison of two extraction methods for evaluation of volatile constituents patterns in commercial whiskeys: Elucidation of the main odour-active compounds

An analytical procedure based on manual dynamic headspace solid-phase microextraction (HS-SPME) method and the conventional extraction method by liquid–liquid extraction (LLE), were compared for their effectiveness in the extraction and quantification of volatile compounds from commercial whiskey samples. Seven extraction solvents covering a wide range of polarities and two SPME fibres coatings, has been evaluated. The highest amounts extracted, were achieved using dichloromethane (CH2Cl2) by LLE method (LLECH2Cl2)(LLECH2Cl2) and using a CAR/PDMS fibre (SPMECAR/PDMS) in HS-SPME. Each method was used to determine the responses of 25 analytes from whiskeys and calibration standards, in order to provide sensitivity comparisons between the two methods. Calibration curves were established in a synthetic whiskey and linear correlation coefficient (r ) were greater than 0.9929 for LLECH2Cl2LLECH2Cl2 and 0.9935 for SPMECAR/PDMS, for all target compounds. Recoveries greater than 80% were achieved. For most compounds, precision (expressed by relative standard deviation, R.S.D.) are very good, with R.S.D. values lower than 14.78% for HS-SPME method and than 19.42% for LLE method. The detection limits ranged from 0.13 to 19.03 μg L−1 for SPME procedure and from 0.50 to 12.48 μg L−1 for LLE. A tentative study to estimate the contribution of a specific compound to the aroma of a whiskey, on the basis of their odour activity values (OAV) was made. Ethyl octanoate followed by isoamyl acetate and isobutyl alcohol, were found the most potent odour-active compounds.

Effectiveness of high-throughput miniaturized sorbent- and solid phase microextraction techniques combined with gas chromatography–mass spectrometry analysis for a rapid screening of volatile and semi-volatile composition of wines: a comparative study

In this study the feasibility of different extraction procedures was evaluated in order to test their potential for the extraction of the volatile (VOCs) and semi-volatile constituents (SVOCs) from wines. In this sense, and before they could be analysed by gas chromatography–quadrupole first stage masss spectrometry (GC–qMS), three different high-throughput miniaturized (ad)sorptive extraction techniques, based on solid phase extraction (SPE), microextraction by packed sorbents (MEPS) and solid phase microextraction (SPME), were studied for the first time together, for the extraction step. To achieve the most complete volatile and semi-volatile signature, distinct SPE (LiChrolut EN, Poropak Q, Styrene-Divinylbenzene and Amberlite XAD-2) and MEPS (C2, C8, C18, Silica and M1 (mixed C8-SCX)) sorbent materials, and different SPME fibre coatings (PA, PDMS, PEG, DVB/CAR/PDMS, PDMS/DVB, and CAR/PDMS), were tested and compared. All the extraction techniques were followed by GC–qMS analysis, which allowed the identification of up to 103 VOCs and SVOCs, distributed by distinct chemical families: higher alcohols, esters, fatty acids, carbonyl compounds and furan compounds. Mass spectra, standard compounds and retention index were used for identification purposes. SPE technique, using LiChrolut EN as sorbent (SPELiChrolut EN), was the most efficient method allowing for the identification of 78 VOCs and SVOCs, 63 and 19 more than MEPS and SPME techniques, respectively. In MEPS technique the best results in terms of number of extractable/identified compounds and total peak areas of volatile and semi-volatile fraction, were obtained by using C8 resin whereas DVB/CAR/PDMS was revealed the most efficient SPME coating to extract VOCs and SVOCs from Bual wine. Diethyl malate (18.8 ± 3.2%) was the main component found in wine SPELiChrolut EN extracts followed by ethyl succinate (13.5 ± 5.3%), 3-methyl-1-butanol (13.2 ± 1.7%), and 2-phenylethanol (11.2 ± 9.9%), while in SPMEDVB/CAR/PDMS technique 3-methyl-1-butanol (43.3 ± 0.6%) followed by diethyl succinate (18.9 ± 1.6%), and 2-furfural (10.4 ± 0.4%), are the major compounds. The major VOCs and SVOCs isolated by MEPSC8 were 3-methyl-1-butanol (26.8 ± 0.6%, from wine total volatile fraction), diethyl succinate (24.9 ± 0.8%), and diethyl malate (16.3 ± 0.9%). Regardless of the extraction technique, the highest extraction efficiency corresponds to esters and higher alcohols and the lowest to fatty acids. Despite some drawbacks associated with the SPE procedure such as the use of organic solvents, the time-consuming and tedious sampling procedure, it was observed that SPELiChrolut EN, revealed to be the most effective technique allowing the extraction of a higher number of compounds (78) rather than the other extraction techniques studied.

Produção de enzimas quitosanolíticas utilizando Paenibacillus ehimensis e Paenibacillus chitinolyticus para obtenção de quitoologossacarídeos

The acquisition of oligosaccharides from chitosan has been the subject of several studies in the pharmaceutical, biochemical, food and medical due to functional properties of these compounds. This study aimed to boost its production of chitooligosaccharides (COS) through the optimization of production and characterization of chitosanolytic enzymes secreted by microorganisms Paenibacillus chitinolyticus and Paenibacillus ehimensis, and evaluating the antioxidant potential of the products obtained. In the process of optimizing the production of chitosanase were employed strategies Fractional Factorial Experimental Design and Central Composite Rotatable Design. The results identified the chitosan, peptone and yeast extract as the components that influenced the production of chitosanase by these microorganisms. With the optimization of the culture media was possible to obtain an increase of approximately 8.1 times (from 0.043 to 0.35 U.mL U.mL-1) and 7.6 times (from 0.08 U.mL-1 to 0.61 U.mL-1) in the enzymatic activity of chitosanase produced by P. chitinolyticus and P. ehimensis respectively. Enzyme complexes showed high stability in temperature ranges between 30º and 55º C and pH between 5.0 and 9.0. Has seen the share of organic solvents, divalent ions and other chemical agents on the activity of these enzymes, demonstrating high stability of these crude complexes and dependence of Mn2+. The COS generated showed the ability of DPPH radical scavenging activity, reaching a maximum rate of scavenging of 61% and 39% when they were produced with enzymes of P. ehimensis and P. chitinolyticus respectively. The use of these enzymes in raw form might facilitate its use for industrial applications

Tratamentos de fibras de carnaúba [copernicia prunífera (miller) h. e. moore] para o desenvolvimento de compósito biodegradável com matriz de polihidroxibutirato

The use of raw materials from renewable sources for production of materials has been the subject of several studies and researches, because of its potential to substitute petrochemical-based materials. The addition of natural fibers to polymers represents an alternative in the partial or total replacement of glass fibers in composites. In this work, carnauba leaf fibers were used in the production of biodegradable composites with polyhydroxybutyrate (PHB) matrix. To improve the interfacial properties fiber / matrix were studied four chemical treatments to the fibers..The effect of the different chemical treatments on the morphological, physical, chemical and mechanical properties of the fibers and composites were investigated by scanning electron microscopy (SEM), infrared spectroscopy, X-ray diffraction, tensile and flexural tests, dynamic mechanical analysis (DMA), thermogravimetry (TGA) and diferential scanning calorimetry (DSC). The results of tensile tests indicated an increase in tensile strength of the composites after the chemical treatment of the fibers, with best results for the hydrogen peroxide treated fibers, even though the tensile strength of fibers was slightly reduced. This suggests a better interaction fiber/matrix which was also observed by SEM fractographs. The glass transition temperature (Tg) was reduced for all composites compared to the pure polymer which can be attributed to the absorption of solvents, moisture and other low molecular weight molecules by the fibers

Injeção de vapor e solvente como um método de recuperação avançada em reservatório avançada em reservatórios de óleo pesado

Currently a resource more and more used by the petroleum industry to increase the efficiency of steam flood mechanism is the addition of solvents. The process can be understood as a combination of a thermal method (steam injection) with a miscible method (solvent injection), promoting, thus, the reduction of interfacial tensions and oil viscosity. The use of solvent alone tends to be limited because of its high cost. When co-injected with steam, the vaporized solvent condenses in the cooler regions of the reservoir and mixes with the oil, creating a zone of low viscosity between the steam and the heavy oil. The mobility of the displaced fluid is then improved, resulting in an increase of oil recovery. To better understand this improved oil recovery method, a numerical study of the process was done contemplating the effects of some operational parameters (distance between wells, injection steam rate, kind of solvent and injected solvent volume)on the accumulated production of oil, recovery factor and oil-steam rate. Semisynthetic models were used in this study but reservoir data can be extrapolated for practical applications situations on Potiguar Basin. Simulations were performed in STARS (CMG, 2007.11). It was found that injected solvent volumes increased oil recovery and oil rates. Further the majority of the injected solvent was produced and can be recycled

Estudo paramétrico do processo de injeção de solventes em poços horizontais para reservatórios de óleos pesados

The world has many types of oil that have a range of values of density and viscosity, these are characteristics to identify whether an oil is light, heavy or even ultraheavy. The occurrence of heavy oil has increased significantly and pointing to a need for greater investment in the exploitation of deposits and therefore new methods to recover that oil. There are economic forecasts that by 2025, the heavy oil will be the main source of fossil energy in the world. One such method is the use of solvent vaporized VAPEX which is known as a recovery method which consists of two horizontal wells parallel to each other, with a gun and another producer, which uses as an injection solvent that is vaporized in order to reduce the viscosity of oil or bitumen, facilitating the flow to the producing well. This method was proposed by Dr. Roger Butler, in 1991. The importance of this study is to analyze how the influence some operational reservoir and parameters are important in the process VAPEX, such as accumulation of oil produced in the recovery factor in flow injection and production rate. Parameters such as flow injection, spacing between wells, type of solvent to be injected, vertical permeability and oil viscosity were addressed in this study. The results showed that the oil viscosity is the parameter that showed statistically significant influence, then the choice of Heptane solvent to be injected showed a greater recovery of oil compared to other solvents chosen, considering the spacing between the wells was shown that for a greater distance between the wells to produce more oil

Análise paramétrica da injeção de vapor e solvente em reservatórios de óleo pesado

A significant fraction of the hydrocarbon reserves in the world is formed by heavy oils. From the thermal methods used to recovery these resources, Steamflooding has been one of the main economically viable alternatives. In Brazil, this technology is widely used by Petrobras in Northeast fields. Latent heat carried by steam heats the oil in the reservoir, reducing its viscosity and facilitating the production. In the last years, an alternative more and more used by the oil industry to increase the efficiency of this mechanism has been the addition of solvents. When co-injected with steam, the vaporized solvent condenses in the cooler regions of the reservoir and mixes with the oil, creating a low viscosity zone between the steam and the heavy oil. The mobility of the displaced fluid is then improved, resulting in an increase of oil recovery. To better understand this improved oil recovery method and investigate its applicability in reservoirs with properties similar to those found in Potiguar Basin, a numerical study was done to analyze the influence of some operational parameters (steam injection rate, injected solvent volume and solvent type) on oil recovery. Simulations were performed in STARS ("Steam, Thermal, and Advanced Processes Reservoir Simulator"), a CMG ("Computer Modelling Group") program, version 2009.10. It was found that solvents addition to the injected steam not only anticipated the heated oil bank arrival to the producer well, but also increased the oil recovery. Lower cold water equivalent volumes were required to achieve the same oil recoveries from the models that injected only steam. Furthermore, much of the injected solvent was produced with the oil from the reservoir